Page is loading ...
Jumpstone – Installation manual
AUDIONETIC_INSTALLATIE HANDLEIDING_1..0 - COPYRIGHT PLAYNETIC 2014
Call us +44(0)131 214 1180
www.inclusiveplay.com
Jumpstone
Jumpstone – Installation manual
AUDIONETIC_INSTALLATIE HANDLEIDING_1..0 - COPYRIGHT PLAYNETIC 2014
Minimal 150 cm
Obstacle free zone
2.Determine the place of the Jumpstone. Take into account
that there are no obstacles in the obstacle free zone. See
picture.
1. Check using the part list if all parts are supplied correctly.
Tijdens installatie moet er zorg voor gedragen worden dat
potentiële gebruikers niet worden blootgesteld aan gevaren.
Before
installation
Mutual dinstance
minimal 40 cm and
maximal 60 cm or
minimal 150 cm
Single
Cluster
Jumpstone – Installation manual
AUDIONETIC_INSTALLATIE HANDLEIDING_1..0 - COPYRIGHT PLAYNETIC 2014
PERMANENT PERMANENT
PREFAB
Select the desired installation method for your application.
For questions please contact your supplier.
Installation
Jumpstone – Installation manual
AUDIONETIC_INSTALLATIE HANDLEIDING_1..0 - COPYRIGHT PLAYNETIC 2014
Cast
Add potting soil
for instalation
0 mm
- 350 mm
One can in itself determine the amount of
potting soil and with it the weight of the
foundation (at least 64 liters potting soil)
Jumpstone – Installation manual
AUDIONETIC_INSTALLATIE HANDLEIDING_1..0 - COPYRIGHT PLAYNETIC 2014
Install the Jumpstone mounting frame
such as the top part is equal and
horizontal with the ground.
Dig a hole of 650 x 350 and 350 mm deep. Set
the mounting frame above the hole and fill it
with potting soil. Make sure the mounting frame
stands upright/level.
Add potting soil
for installation
Jumpstone – Installation manual
AUDIONETIC_INSTALLATIE HANDLEIDING_1..0 - COPYRIGHT PLAYNETIC 2014
Remove all M10 bolts ont he outside of the
Jumpstone and remove the service hatch.
Lift the outside hood and the rubbet tile.
Place the Jumpstone on the mounting
frame.
Add potting soil
for installation
Jumpstone – Installation manual
AUDIONETIC_INSTALLATIE HANDLEIDING_1..0 - COPYRIGHT PLAYNETIC 2014
Confirm 4x M10 bolts at the marked
holes indicated above in the
mounting frame.
Mount in reverse direction. See
previous page.
Firstly remove the axis by pulling it
upwards. Keep the spring. Romove
the four bolts on the place of the
circles. After that; lift the plate a
little and disconnet the plugs of the
mini computer by twisting the front
side of the plugs untill you can
remove them smoothly.
Add potting soil
for installation
Jumpstone – Installation manual
AUDIONETIC_INSTALLATIE HANDLEIDING_1..0 - COPYRIGHT PLAYNETIC 2014
Installation
using prefab
concrete block
PERMANENT PREFAB
0 mm
- 350 mm
- Great for in tile plateau (300x300mm);
- Easy installation based on prefab concrete block
Jumpstone – Installation manual
AUDIONETIC_INSTALLATIE HANDLEIDING_1..0 - COPYRIGHT PLAYNETIC 2014
Monteer de adapterplaat aan de
Audionetic. Houdt de verzonken
gaten aan de onderzijde. Plaat
vastzetten met de 4 bouten.
Install the concrete block in such a way
that the top is equal and horizontal with
the ground level.
350 mm
Dig a hole of at least 350 x 350 mm
and 350 mm deep.
350 mm
Installation
using prefab
concrete block
Jumpstone – Installation manual
AUDIONETIC_INSTALLATIE HANDLEIDING_1..0 - COPYRIGHT PLAYNETIC 2014
Installation
using prefab
concrete block
Remove all M10 bolts on the outside of the
Jumpstone. Remove the service hatch.
Lift the outside hood and the rubber tile
from the Jumpstone and place the
Jumpstone on the mouting frame.
Jumpstone – Installation manual
AUDIONETIC_INSTALLATIE HANDLEIDING_1..0 - COPYRIGHT PLAYNETIC 2014
Installation
using prefab
concrete block
. Firstly remove the axis by pulling it
upwards. Keep the spring. Romove
the four bolts on the place of the
circles. After that; lift the plate a
little and disconnet the plugs of the
mini computer by twisting the front
side of the plugs untill you can
remove them smoothly.
Confirm 4x M10 bolts at the marked
holes indicated above in the
mounting frame.
Mount in reverse direction. See
previous page.
/
