Hearth and Home Technologies SL-350TRS-D User manual

Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 1

Models:

SL-750TRS-IPI-E

SL-550TRS-IPI-E

SL-350TRS-D

SL-350TRS-IPI

Owner’s Manual

Installation and Operation

• Do not store or use gasoline or other ﬂ am-

mable vapors and liquids in the vicinity of

this or any other appliance.

• What to do if you smell gas

- Do not try to light any appliance

- Do not touch any electrical switch. Do not

use any phone in your building.

- Immediately call your gas supplier from a

neighbor’s phone. Follow the gas suppli-

er’s instructions.

- If you cannot reach your gas supplier, call

the ﬁ re department.

• Installation and service must be performed

by a qualiﬁ ed installer, service agency, or the

gas supplier.

WARNING: If the information in these

instructions is not followed exactly, a ﬁ re

or explosion may result causing property

damage, personal injury, or death.

DO NOT DISCARD THIS MANUAL

CAUTION

This appliance may be installed as an OEM installation in

manufactured home (USA only) or mobile home and must be

installed in accordance with the manufacturer’s instructions and

the manufactured home construction and safety standard, Title

24 CFR, Part 3280 or Standard for Installation in Mobile Homes,

CAN/CSA Z240MH.

This appliance is only for use with the type(s) of gas indicated

on the rating plate.

Installation and service of this appliance should be

performed by qualiﬁ ed personnel. Hearth & Home

Technologies suggests NFI certiﬁ ed or factory trained

professionals, or technicians supervised by an NFI

certiﬁ ed professional.

• Leave this manual with

party responsible for use

and operation.

DO NOT

DISCARD

WARNING

• Important operating

and maintenance

instructions included.

• Read, understand and follow

these instructions for safe

installation and operation.

In the Commonwealth of Massachusetts:

• installation must be performed by a licensed plumber

or gas ﬁ tter;

See Table of Contents for location of additional

Commonwealth of Massachusetts requirements.

This appliance has been supplied with an integral barrier

to prevent direct contact with the ﬁ xed glass panel. Do

NOT operate the appliance with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the

barrier is not present or help is needed to properly install one.

HOT! DO NOT TOUCH.

SEVERE BURNS MAY RESULT.

CLOTHING IGNITION MAY RESULT.

• CAREFULLY SUPERVISE children in same room as

appliance.

• Alert children and adults to hazards of high temperatures.

• Do NOT operate with protective barriers open or

removed.

• Keep clothing, furniture, draperies and other combustibles

away.

Glass and other surfaces are hot during

operation and cool down.

• Keep children away.

Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/072

Congratulations

Listing Label Information/Location

Model Name: ___________________________________________ Date purchased/installed: __________________

Serial Number: __________________________________________ Location on appliance: ____________________

Dealership purchased from: _______________________________ Dealer Phone: __________________________

Notes: _______________________________________________________________________________________

_____________________________________________________________________________________________

Congratulations on selecting a Heat & Glo gas appliance

—an elegant and clean alternative to wood burning

appliances. The Heat & Glo gas appliance you have

selected is designed to provide the utmost in safety,

reliability, and efﬁ ciency.

As the owner of a new appliance, you’ll want to read and

carefully follow all of the instructions contained in this

Owner’s Manual. Pay special attention to all Cautions and

Warnings.

This Owner’s Manual should be retained for future

reference. We suggest that you keep it with your other

important documents and product manuals.

The information contained in this Owner’s Manual, unless

noted otherwise, applies to all models and gas control

systems.

Your new Heat & Glo gas appliance will give you years of

durable use and trouble-free enjoyment. Welcome to the

Heat & Glo family of appliance products!

Read this manual before installing or operating this appliance.

Please retain this owner’s manual for future reference.

We recommend that you record the following pertinent

information about your appliance.

Gas and Electric

Information

Serial Number

Type of Gas

The model information regarding your speciﬁ c appliance can be found on

the rating plate usually located in the control area of the appliance.

Homeowner Reference Information

Heat & Glo, a of Hearth & Home Technologies, Inc.

20802 Kensington Boulevard, Lakeville, MN 55044

brand

Heat & Glo, a of Hearth & Home Technologies, Inc.

20802 Kensington Boulevard, Lakeville, MN 55044

brand

Not

for

use

with

solid

fuel.

(

Ne

doit

pas

entre

utilise

avec

un

combustible

solide).

This

appliance

must

be

installed

in

accordance

with

local

codes,

if

any;

if

not,

follow

ANSI

Z223.1

in

the

USA

or

CAN/CGA

B149

installation

codes.

(Installer

l’appareil

selon

les

codes

ou

reglements

locaux

ou,

en

l’absence

de

tels

reglements,

selon

les

codes

d’installation

CAN/CGA-B149.)

Type

of

Gas

(Sorte

De

Gaz)

Gaz):

NA

TURAL

GAS

MADE

IN

USA

Minimum

Permissible

Gas

Supply

for

Purposes

of

Input

Adjustment.

Approved

Minimum

(De

Gaz)

Acceptable

0.0

in

w.c.

(Po.

Col.

d’eau)

Maximum

Pressure

(Pression)

0.0

in

w.c.

(Po.

Col.

d’eau)

Maximum

Manifold

Pressure

(Pression)

0.0

in

w.c.

(Po.

Col.

d’eau)

Minimum

Manifold

Pressure

(Pression)

0.0

in

w.c.

(Po.

Col.

d’eau)

Model:

(Modele):

Serial

(Serie):

ANSI

Z21XX-XXXX

·

CSA

2.XX-MXX

·

UL307B

XXXXXXXX

IN

CANADA

ALTITUDE:

0-0000

FT.

0000-0000FT.

MAX.

INPUT

BTUH:

00,000

MIN.

INPUT

BTUH:

00,000

ORIFICE

SIZE:

#XXXXX

XXXXXXXX

Total

Electrical

Requirements:

000Vac,

00Hz.,

less

than

00

Amperes

This product may be covered by one or more of the following patents: (Nos produits sont couverts par un ou plusieurs des brevets suivants): (United States)

4593510, 4686807, 4766876, 4793322, 4811534, 5000162, 5016609, 5076254, 5113843, 5191877, 5218953, 5263471, 5328356, 5341794, 5347983, 5429495,

5452708, 5542407, 5601073, 5613487, 5647340, 5688568, 5762062, 5775408, 5890485, 5931661, 5941237, 5947112, 5996575, 6006743, 6019099, 6048195,

6053165, 6145502, 6170481, 6237588, 6296474, 6374822, 6413079, 6439226, 6484712, 6543698, 6550687, 6601579, 6672860, 6688302B2, 6715724B2,

6729551, 6736133, 6748940, 6748942, D320652, D445174, D462436; (Canada)1297749, 2195264, 2225408; or other U.S. and foreign patents pending (ou

autres brevets americains et etrangers en attente).

Model Number

Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 3

Î = Contains updated information.

Table of Contents

1 Listing and Code Approvals

A. Appliance Certiﬁ cation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

B. Glass Speciﬁ cations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

C. BTU Speciﬁ cations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

D. High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . . . . 4

E. Non-Combustible Materials Speciﬁ cation. . . . . . . . . . . . . . 4

F. Combustible Materials Speciﬁ cation . . . . . . . . . . . . . . . . . 4

G. Requirements for the Commonwealth of Massachusetts . . 5

2 Getting Started

A. Design and Installation Considerations . . . . . . . . . . . . . . . 6

B. Tools and Supplies Needed . . . . . . . . . . . . . . . . . . . . . . . . 6

C. Inspect Appliance and Components . . . . . . . . . . . . . . . . . . 6

3 Framing and Clearances

A. Selecting Appliance Location . . . . . . . . . . . . . . . . . . . . . . . 7

B. Constructing the Appliance Chase . . . . . . . . . . . . . . . . . . . 8

C. Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

D. Elevated Hearth Systems . . . . . . . . . . . . . . . . . . . . . . . . . . 9

E. Mantel Projections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

4 Termination Locations

A. Vent Termination Minimum Clearances . . . . . . . . . . . . . . .11

5 Vent Information and Diagrams

A. Vent Table Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

B. Use of Elbows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

C. Measuring Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

D. Use of Flex Vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

E. Vent Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

6 Vent Clearances and Framing

A. Pipe Clearances to Combustibles . . . . . . . . . . . . . . . . . . 25

B. Wall Penetration Framing . . . . . . . . . . . . . . . . . . . . . . . . . 25

C. Vertical Penetration Framing . . . . . . . . . . . . . . . . . . . . . . 26

7 Appliance Preparation

A. Top Vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

B. Rear Vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

C. Securing and Leveling the Appliance . . . . . . . . . . . . . . . . 29

8 Installing Vent Pipe

A. Assembly of Vent Sections (DVP Pipe) . . . . . . . . . . . . . . 30

B. Disassembly of Vent Sections (DVP Pipe) . . . . . . . . . . . . 32

C. Installing Heat Shield and Horizontal Termination Cap

(DVP Pipe) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

D. Assembly of Vent Sections (SL pipe) . . . . . . . . . . . . . . . . 34

E. Installing Wall Shield Firestops and Horizontal

Termination Cap (SL Pipe) . . . . . . . . . . . . . . . . . . . . . . . . 35

F. Installing Roof Flashing and Vertical Termination Cap . . . 36

9 Gas Information

A. Fuel Conversions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

B. Gas Pressures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

C. Gas Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

10 Electrical Information

A. Recommendation for Wire . . . . . . . . . . . . . . . . . . . . . . . . 40

B. Connecting to the Appliance. . . . . . . . . . . . . . . . . . . . . . . 40

C. Intelliﬁ re Ignition System Wiring . . . . . . . . . . . . . . . . . . . . 41

D. Standing Pilot Ignition System Wiring . . . . . . . . . . . . . . . 41

E. Junction Box Installation. . . . . . . . . . . . . . . . . . . . . . . . . . 43

F. Wall Switch Installation for Fan (Optional) . . . . . . . . . . . . 43

11 Finishing

A. Mantel Projections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

B. Facing Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

C. Splatter Guard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

D. Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

12 Appliance Setup

A. Remove Shipping Materials . . . . . . . . . . . . . . . . . . . . . . . 49

B. Clean the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

C. Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

D. Lava Rock, Mineral Wool/Ember Placement . . . . . . . . . . 49

E. Install Refractory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

F. Positioning the Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

G. Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

H. Grilles and Trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

I. Air Shutter Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

13 Operating Instructions

A. Before Lighting Appliance. . . . . . . . . . . . . . . . . . . . . . . . . 58

B. Lighting Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

C. After Appliance is Lit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

D. Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . 61

14 Troubleshooting

A. Standing Pilot Ignition System . . . . . . . . . . . . . . . . . . . . . 62

B. Intelliﬁ re Ignition System . . . . . . . . . . . . . . . . . . . . . . . . . 64

15 Maintaining and Servicing Appliance

A. Maintenance Tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

16 Reference Materials

A. Appliance Dimension Diagram . . . . . . . . . . . . . . . . . . . . . 68

B. Vent Components Diagrams . . . . . . . . . . . . . . . . . . . . . . 69

C. Service Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

D. Limited Lifetime Warranty . . . . . . . . . . . . . . . . . . . . . . . . . 84

E. Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/074

MODELS: SL-750TRS-IPI-E,SL-550TRS-IPI-E,

SL-350TRS-D, SL-350TRS-IPI

LABORATORY: Underwriters Laboratories, Inc. (UL)

TYPE: Direct Vent Gas Appliance Heater

STANDARD: ANSI Z21.88a-2007 • CSA 2.33a-2007

Models

U.S. (0-2000 ft.) or

Canada (2000-4500 ft.)

Maximum

Input

BTU/h

Minimum

Input

BTU/h

Oriﬁ ce

Size

(DMS)

SL-750TRS-IPI-E (NG) U.S. 30,800 20,200 #37

Canada 27,720 18,180 #38

SL-750TRS-IPI-E (LP) U.S. 30,700 23.300 #52

Canada 27,630 20,970 #53

SL-550TRS-IPI-E (NG) U.S. 27,300 18,200 #40

Canada 24,570 16,380 #41

SL-550TRS-IPI-E (LP) U.S. 25,100 18,300 #53

Canada 22,590 16,470 #54

SL-350TRS-D (NG)

SL-350TRS-IPI (NG) U.S. 20,500 14,400 #44

Canada 18,450 12,960 #45

SL-350TRS-D (LP)

SL-350TRS-IPI (LP) U.S. 20,000 14,900 #55

Canada 18,000 13,410 #56

B. Glass Speciﬁ cations

Hearth & Home Technologies appliances manufactured

with tempered glass may be installed in hazardous loca-

tions such as bathtub enclosures as deﬁ ned by the Con-

sumer Product Safety Commission (CPSC). The tempered

glass has been tested and certiﬁ ed to the requirements

of ANSI Z97.1 and CPSC 16 CFR 1202 (Safety Glazing

Certiﬁ cation Council SGCC# 1595 and 1597. Architectur-

al Testing, Inc. Reports 02-31919.01 and 02-31917.01).

This statement is in compliance with CPSC 16 CFR Sec-

tion 1201.5 “Certiﬁ cation and labeling requirements”

which refers to 15 U.S. Code (USC) 2063 stating “…Such

certiﬁ cate shall accompany the product or shall otherwise

be furnished to any distributor or retailer to whom the

product is delivered.”

Some local building codes require the use of tempered

glass with permanent marking in such locations. Glass

meeting this requirement is available from the factory.

Please contact your dealer or distributor to order.

Note: This installation must conform with local codes. In the

absence of local codes you must comply with the National

Fuel Gas Code, ANSI Z223.1-latest edition in the U.S.A. and

the CAN/CGA B149 Installation Codes in Canada.

1

1 Listing and Code Approvals

C. BTU Speciﬁ cations

Do NOT use this appliance if any part has been under water.

Immediately call a qualiﬁ ed service technician to inspect the

appliance and to replace any part of the control system and

any gas control which has been under water.

This product is listed to ANSI standards for “Vented Gas

Appliance Heaters” and applicable sections of “Gas Burn-

ing Heating Appliances for Manufactured Homes and

Recreational Vehicles”, and “Gas Fired Appliances for

Use at High Altitudes”.

Heat & Glo Quality Systems

registered by SGS ICS

A. Appliance Certiﬁ cation

E. Non-Combustible Materials Speciﬁ cation

Material which will not ignite and burn. Such materials are

those consisting entirely of steel, iron, brick, tile, concrete,

slate, glass or plasters, or any combination thereof. Mate-

rials that are reported as passing ASTM E 136, Standard

Test Method for Behavior of Materials in a Vertical

Tube Furnace at 750ºC, shall be considered non-com-

bustible materials.

F. Combustible Materials Speciﬁ cation

Materials made of or surfaced with wood, compressed

paper, plant ﬁ bers, plastics, or other material that can ig-

nite and burn, whether ﬂ ame proofed or not, or whether

plastered or unplastered shall be considered combustible

materials.

WARNING

NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.

This appliance is tested and approved as either supplemen-

tal room heat or as a decorative appliance. It should not be

factored as primary heat in residential heating calculations. D. High Altitude Installations

U.L. Listed gas appliances are tested and approved with-

out requiring changes for elevations from 0 to 2000 feet in

the U.S.A. and Canada.

When installing this appliance at an elevation above 2000

feet, it may be necessary to decrease the input rating

by changing the existing burner oriﬁ ce to a smaller size.

Input rate should be reduced by 4% for each 1000 feet

above a 2000 foot elevation in the U.S.A., or 10% for el-

evations between 2000 and 4500 feet in Canada. If the

heating value of the gas has been reduced, these rules

do not apply. To identify the proper oriﬁ ce size, check with

the local gas utility.

If installing this appliance at an elevation above 4500 feet

(in Canada), check with local authorities.

Î

Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 5

G. Requirements for the Commonwealth of

Massachusetts

For all side wall horizontally vented gas fueled equipment

installed in every dwelling, building or structure used in

whole or in part for residential purposes, including those

owned or operated by the Commonwealth and where the

side wall exhaust vent termination is less than seven (7)

feet above ﬁ nished grade in the area of the venting, in-

cluding but not limited to decks and porches, the following

requirements shall be satisﬁ ed:

Installation of Carbon Monoxide Detectors

At the time of installation of the side wall horizontal vented

gas fueled equipment, the installing plumber or gas ﬁ tter

shall observe that a hard wired carbon monoxide detector

with an alarm and battery back-up is installed on the ﬂ oor

level where the gas equipment is to be installed. In addi-

tion, the installing plumber or gas ﬁ tter shall observe that

a battery operated or hard wired carbon monoxide detec-

tor with an alarm is installed on each additional level of

the dwelling, building or structure served by the side wall

horizontal vented gas fueled equipment. It shall be the

responsibility of the property owner to secure the services

of qualiﬁ ed licensed professionals for the installation of

hard wired carbon monoxide detectors.

In the event that the side wall horizontally vented gas fu-

eled equipment is installed in a crawl space or an attic,

the hard wired carbon monoxide detector with alarm and

battery back-up may be installed on the next adjacent

ﬂ oor level.

In the event that the requirements of this subdivision can

not be met at the time of completion of installation, the

owner shall have a period of thirty (30) days to comply

with the above requirements; provided, however, that dur-

ing said thirty (30) day period, a battery operated carbon

monoxide detector with an alarm shall be installed.

Approved Carbon Monoxide Detectors

Each carbon monoxide detector as required in accor-

dance with the above provisions shall comply with NFPA

720 and be ANSI/UL 2034 listed and IAS certiﬁ ed.

Signage

A metal or plastic identiﬁ cation plate shall be permanent-

ly mounted to the exterior of the building at a minimum

height of eight (8) feet above grade directly in line with the

exhaust vent terminal for the horizontally vented gas fu-

eled heating appliance or equipment. The sign shall read,

in print size no less than one-half (1/2) inch in size, “GAS

VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OB-

STRUCTIONS”.

Inspection

The state or local gas inspector of the side wall horizon-

tally vented gas fueled equipment shall not approve the

installation unless, upon inspection, the inspector ob-

serves carbon monoxide detectors and signage installed

in accordance with the provisions of 248 CMR 5.08(2)(a)1

through 4.

Exemptions

The following equipment is exempt from 248 CMR

5.08(2)(a)1 through 4:

• The equipment listed in Chapter 10 entitled “Equip-

ment Not Required To Be Vented” in the most current

edition of NFPA 54 as adopted by the Board; and

• Product Approved side wall horizontally vented gas fu-

eled equipment installed in a room or structure sep-

arate from the dwelling, building or structure used in

whole or in part for residential purposes.

MANUFACTURER REQUIREMENTS

Gas Equipment Venting System Provided

When the manufacturer of Product Approved side wall

horizontally vented gas equipment provides a venting

system design or venting system components with the

equipment, the instructions provided by the manufacturer

for installation of the equipment and the venting system

shall include:

• Detailed instructions for the installation of the venting

system design or the venting system components; and

• A complete parts list for the venting system design or

venting system.

Gas Equipment Venting System NOT Provided

When the manufacturer of a Product Approved side wall

horizontally vented gas fueled equipment does not pro-

vide the parts for venting the ﬂ ue gases, but identiﬁ es

“special venting systems”, the following requirements

shall be satisﬁ ed by the manufacturer:

• The referenced “special venting system” instructions

shall be included with the appliance or equipment in-

stallation instructions; and

• The “special venting systems” shall be Product Ap-

proved by the Board, and the instructions for that sys-

tem shall include a parts list and detailed installation

instructions.

A copy of all installation instructions for all Product Ap-

proved side wall horizontally vented gas fueled equip-

ment, all venting instructions, all parts lists for venting

instructions, and/or all venting design instructions shall

remain with the appliance or equipment at the completion

of the installation.

See Gas Connection section for additional Common-

wealth of Massachusetts requirements.

Note: The following requirements reference various

Massachusetts and national codes not contained in this

document.

Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/076

A. Design and Installation Considerations

Heat & Glo direct vent gas appliances are designed to

operate with all combustion air siphoned from outside of

the building and all exhaust gases expelled to the out-

side. No additional outside air source is required.

2

2 Getting Started

C. Inspect Appliance and Components

When planning an appliance installation, it’s necessary to

determine the following information before installing:

• Where the appliance is to be installed.

• The vent system conﬁ guration to be used.

• Gas supply piping.

• Electrical wiring.

• Framing and ﬁ nishing details.

• Whether optional accessories—devices such as a fan,

wall switch, or remote control—are desired.

B. Tools and Supplies Needed

Before beginning the installation be sure that the following

tools and building supplies are available.

Reciprocating saw Framing material

Pliers Hi temp caulking material

Hammer Gloves

Phillips screwdriver Framing square

Flat blade screwdriver Electric drill and bits (1/4 in.)

Plumb line Safety glasses

Level 1/2 - 3/4 inch length, #6 or #8 Self-drilling screws

Manometer Voltmeter

Tape measure Noncorrosive leak check solution

One 1/4 inch female connection (for optional fan).

• Carefully remove the appliance and components from

the packaging.

• The vent system components and trim doors are shipped

in separate packages.

• The gas logs may be packaged separately and must be

ﬁ eld installed.

• Report to your dealer any parts damaged in shipment,

particularly the condition of the glass.

• Read all of the instructions before starting the insta-

llation. Follow these instructions carefully during the

installation to ensure maximum safety and beneﬁ t.

Check building codes prior to installation.

• Installation MUST comply with local, regional, state and

national codes and regulations.

• Consult local building, ﬁ re ofﬁ cials or authorities having jurisdic-

tion about restrictions, installation inspection, and permits.

CAUTION

Keep appliance dry.

• Mold or rust may cause odors.

• Water may damage controls.

Inspect appliance and components for damage.

Damaged parts may impair safe operation.

• Do NOT install damaged components.

• Do NOT install incomplete components.

• Do NOT install substitute components.

Report damaged parts to dealer.

Hearth & Home Technologies disclaims any

responsibility for, and the warranty will be voided

by, the following actions:

• Installation and use of any damaged appliance or vent

system component.

• Modiﬁ cation of the appliance or vent system.

• Installation other than as instructed by Hearth & Home

Technologies.

• Improper positioning of the gas logs or the glass door.

• Installation and/or use of any component part not approved

by Hearth & Home Technologies.

Any such action may cause a ﬁ re hazard.

WARNING

Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 7

K

C

A

L

F

I

B

G

E

D

J

JG

A

F

CA

H

M

N

In addition to these framing dimensions, also reference the following sections:

• Clearances and Mantel Projections (Section 3.C and 3.D)

• Vent Clearances and Framing (Section 6).

3

3 Framing and Clearances

Note:

• Illustrations reflect typical installations and are FOR

DESIGN PURPOSES ONLY.

• Illustrations/diagrams are not drawn to scale.

• Actual installation may vary due to individual design

preference.

Fire Risk

Provide adequate clearance:

• Around air openings

• To combustibles

• For service access

Locate appliance away from trafﬁ c areas.

A. Selecting Appliance Location

When selecting a location for your appliance it is important to

consider the required clearances to walls (see Figure 3.1).

Figure 3.1 Appliance Locations

NOTE: For actual appliance dimensions refer to Sec-

tion 16.

WARNING

Models A B C D E

Min. F

Min. GH I JKL M N

SL-750TRS-IPI-E in. 45-1/2 42 64-3/8

See Section

E for Alcove

Installation

1 1/2 45-1/2 64-3/8 16-1/4 48-1/2 68-3/4 16-5/8 7-1/2 9

mm 1155 1067 1635 25 13 1155 1635 413 1232 1737 422 191 229

SL-550TRS-IPI-E in. 42 37 59-1/2 1 1/2 44 62-1/4 16-1/4 48-1/2 68-3/4 15-1/16 7-1/2 7-1/8

mm 1067 940 1511 25 13 1117 1581 413 1232 1737 383 191 181

SL-350TRS-D in. 39-1/2 34 55-7/8 1 1/2 44 62-1/4 16-1/4 48-1/2 68-3/4 13-1/2 7-1/2 6

mm 1003 864 1413 25 13 1117 1581 413 1232 1737 343 191 152

Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/078

Figure 3.2 Clearances to Combustibles

C

B

D

A

Models

ABCDEFGHIJ

DVP PIPE SL PIPE Rough

Opening

(Height)

*DVP PIPE SL PIPE Rough

Opening

(Width)

Clearance

to Ceiling Combustible

Floor Combustible

Flooring Behind

Appliance Sides of

Appliance Front of

Appliance

Rough

Opening

(Width)

Rough

Opening

(Width)

Rough

Opening

(Depth)

Rough

Opening

(Depth)

SL-750TRS-IPI-E Inches 10 8-5/8 38-1/4 28-1/4 16-1/4 42 32 0 0 1/2 1/2 36

Millimeters 254 219 971 699 413 1067 813 0 0 13 13 915

SL-550TRS-IPI-E Inches 10 8-5/8 34-3/4 28-1/4 16-1/4 37 32 0 0 1/2 1/2 36

Millimeters 254 219 882 699 413 940 813 0 0 13 13 915

SL-350TRS-D Inches 10 8-5/8 32-3/4 28-1/4 16-1/4 34 32 0 0 1/2 1/2 36

Millimeters 254 219 832 699 413 864 813 0 0 13 13 915

E

H

I

F

G

J

MEASURE FROM

TOP OF UNIT OPENING

OR FROM TOP OF HOOD

Fire Risk.

• Construct chase to all clearance speciﬁ cations

in manual.

• Locate and install appliance to all clearance

speciﬁ cations in manual.

B. Constructing the Appliance Chase

A chase is a vertical boxlike structure built to enclose the

gas appliance and/or its vent system. Vertical vents that

run on the outside of a building may be, but are not re-

quired to be, installed inside a chase.

Construction of the chase may vary with the type of build-

ing. These instructions are not substitutes for the require-

ments of local building codes. Local building codes MUST

be checked.

Chases should be constructed in the manner of all out-

side walls of the home to prevent cold air drafting prob-

lems. The chase should not break the outside building

envelope in any manner.

Walls, ceiling, base plate and cantilever ﬂ oor of the chase

should be insulated. Vapor and air inﬁ ltration barriers

should be installed in the chase as per regional codes for

the rest of the home. Additionally, in regions where cold

air inﬁ ltration may be an issue, the inside surfaces may be

sheetrocked and taped for maximum air tightness.

To further prevent drafts, the wall shield and ceiling

ﬁ restops should be caulked with high temperature caulk

to seal gaps. Gas line holes and other openings should

be caulked with high temp caulk or stuffed with unfaced

C. Clearances

Fire Risk.

Odor Risk.

• Install appliance on hard metal or wood surfaces

extending full width and depth of appliance.

• Do NOT install appliance directly on carpeting,

vinyl, tile or any combustible material other than

wood.

insulation. If the appliance is being installed on a cement

slab, a layer of plywood may be placed underneath to pre-

vent conducting cold up into the room.

WARNING

* Dimension when rear venting with one 90º elbow

Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 9

D. Elevated Hearth Systems

Use the table below to identify the hearth system that will be used. The table will also help identify effects on the various dimensions.

Some hearth systems will elevate the appliance off the ﬂ oor at a given dimension. For example, if appliance will be used with a

Kenwood Cabinet with Base, the appliance will be elevated 9-1/4 inches. The 9-1/4 inch elevation will also have to be added to the

following: Extension Wall Hole referenced in Figure 6.3 (Exterior Wall Hole) and Rough Opening Height (header height) referenced in

Figure 3.2. NOTE: Finished ﬂ oor thickness should also be considered when determining installation dimensions.

MODEL DESCRIPTION PART # ELEVATED APPLIANCE

DIMENSION

See Note 1

MARBLE LEG CUT

LENGTH

See Note 2

SL-350

KENWOOD CABINET KDC44SBP 0 27 3/8 in.

KENWOOD CABINET W/ BASE KDC44SBP W/ HTKDC44SBP 9 1/4 in. 27 3/8 in.

KENWOOD CORNER CABINET KDA44SBP 0 27 3/8 in.

KENWOOD CORNER CABINET W/ BASE KDA44SBP W/ HTKDA44SBP 9 1/4 in. 27 3/8 in.

SL-550

KENWOOD CABINET KDC44SBP 0 29-3/8 in.

KENWOOD CABINET W/ BASE KDC44SBP W/ HTKDC44SBP 9-1/4 in. 29-3/8 in.

KENWOOD CORNER CABINET KDA44SBP 0 29-3/8 in.

KENWOOD CORNER CABINET W/ BASE KDA44SBP W/ HTKDA44SBP 9-1/4 in. 29-3/8 in.

KENWOOD MANTEL AFKDMPA 0 (See Note 3) 27-3/8 in.

KENWOOD MANTEL W/ BASE AFKDMPA W/ HTKDMPA 9 1/4 in. 29-3/8 in.

LAURENT SURROUND LAURENT-32 1-1/2 in. N/A

CAMDEN SURROUND CAM550PG 0 N/A

CAMDEN SURROUND W/HEARTH CAM550PGH 1-3/4 in. N/A

CAMDEN SURROUND W/MANTEL CAMM550PG 0 N/A

CAMDEN SURROUND W/MANTEL &

HEARTH CAMM550PGH 1-3/4 in. N/A

ESSEX SURROUND ESSEX550PG 0 N/A

ESSEX SURROUND W/HEARTH ESSEX550PGH 1-3/4 in. N/A

ESSEX SURROUND W/MANTEL ESSEXM550PG 0 N/A

ESSEX SURROUND W/MANTEL &

HEARTH ESSEXM550PGH 1-3/4 in. N/A

MONROE SURROUND MON550PG 0 N/A

MONROE SURROUND W/HEARTH MON550PGH 1-3/4 in. N/A

MONROE SURROUND W/MANTEL MONM550PG 0 N/A

MONROE SURROUND W/MANTEL &

HEARTH MONM550PGH 1-3/4 in. N/A

SL-750

KENWOOD CABINET KDC48DBP 0 32-7/8 in.

KENWOOD CABINET W/ BASE KDC48DBP W/ HTKDC48DBP 9-1/4 in. 32-7/8 in.

KENWOOD CORNER CABINET KDA48SBP 0 32-7/8 in.

KENWOOD CORNER CABINET W/ BASE KDA48SBP W/ HTKDA48SBP 9-1/4 in. 32-7/8 in.

KENWOOD MANTEL AFKDMPB 0 (See Note 3) 27-3/8 in.

KENWOOD MANTEL W/ BASE AFKDMPB W/ HTKDMPB 9-1/4 in. 29-3/8 in.

LAURENT SURROUND LAURENT-36 1-1/2 in. N/A

CAMDEN SURROUND CAM36PG 0 N/A

CAMDEN SURROUND W/HEARTH CAM36PGH 1-3/4 in. N/A

CAMDEN SURROUND W/MANTEL CAMM36PG 0 N/A

CAMDEN SURROUND W/MANTEL &

HEARTH CAMM36PGH 1-3/4 in. N/A

ESSEX SURROUND ESSEX36PG 0 N/A

ESSEX SURROUND W/HEARTH ESSEX36PGH 1-3/4 in. N/A

ESSEX SURROUND W/MANTEL ESSEXM36PG 0 N/A

ESSEX SURROUND W/MANTEL &

HEARTH ESSEXM36PGH 1-3/4 in. N/A

MONROE SURROUND MON36PG 0 N/A

MONROE SURROUND W/HEARTH MON36PGH 1-3/4 in. N/A

MONROE SURROUND W/MANTEL MONM36PG 0 N/A

MONROE SURROUND W/MANTEL &

HEARTH MONM36PGH 1-3/4 in. N/A

NOTE 1. Add dimensions to Exterior Wall Hole (Figure 6.3) and Rough Opening Height (Figure 3.2).

NOTE 2. Verify Marble Cut Lengths on site prior to cutting.

NOTE 3. Dimensions assume use of a 3/4 in. Hearth Pad.

Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/0710

E. Mantel Projections

5678910

345

12

11

10

9

8

7

6

TOP OF HOOD OR FIREPLACE OPENING

4

12 13

11

32

CEILING

All measurements are in inches.

Figure 3.3 Clearances to mantels or other combustibles

above appliance

1/2 in.

SHEETROCK

3-1/2 in.

1/2 in.

NON-COMBUSTIBLE ZONE

NON-COMBUSTIBLE

BOARD SHIPPED

WITH APPLIANCE

Figure 3.4 Non-Combustible Zone

3 FT. MAXIMUM

2-7/8 IN.

MINIMUM

1/2 IN.

MINIMUM

Note: Clearance from opening

to perpendicular wall.

Figure 3.5 Clearances to Mantel Legs or Wall Projections

(Acceptable on both sides of opening.)

5-3/8 IN.

MINIMUM

3 IN.

MINIMUM

UNLIMITED

Note: Clearance from opening

to perpendicular wall.

Figure 3.6 Wall Projection (Acceptable on one side of opening.)

Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 11

A. Vent Termination Minimum Clearances

Fire Risk.

Explosion Risk.

Maintain vent clearance to combustibles as

speciﬁ ed.

• Do not pack air space with insulation or other

materials.

Failure to keep insulation or other materials

away from vent pipe may cause ﬁ re.

Roof Pitch H (Min.) Ft.

Flat to 6/12...........................................................1.0*

Over 6/12 to 7/12 .................................................1.25*

Over 7/12 to 8/12 .................................................1.5*

Over 8/12 to 9/12 .................................................2.0*

Over 9/12 to 10/12 ...............................................2.5

Over 10/12 to 11/12 .............................................3.25

Over 11/12 to 12/12 .............................................4.0

Over 12/12 to 14/12 .............................................5.0

Over 14/12 to 16/12 .............................................6.0

Over 16/12 to 18/12 .............................................7.0

Over 18/12 to 20/12 .............................................7.5

Over 20/12 to 21/12 .............................................8.0

Figure 4.1

Figure 4.2 Minimum height from roof to lowest discharge

opening

4

4 Termination Locations

Measure horizontal clearances from this surface.

Measure vertical clearances from this surface.

Figure 4.3 Multiple Vertical Termination

Figure 4.2 speciﬁ es minimum vent heights for various

pitched roofs.

(See Figure 4.4 for speciﬁ c clearances)

* 3 foot minimum in snow regions

HORIZONTAL

OVERHANG

VERTICAL

WALL

GAS DIRECT VENT

TERMINATION CAP

12

X

ROOF PITCH

IS X/ 12

LOWEST

DISCHARGE

OPENING

2 FT.

MIN.

20 INCHES MIN.

H (MIN.) - MINIMUM HEIGHT FROM ROOF

TO LOWEST DISCHARGE OPENING

C

A

GAS

TERMINATION

B

GAS, WOOD OR FUEL

OIL TERMINATION

WARNING

Gas

Termination Wood & Fuel Oil

Termination Comments

A6 in. 20 in. min. Horizontal distance between terminations

B20 in. 24 in. min. Distance to perpendicular wall

C18 in. 18 in. Vertical distance between terminations

Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/0712

V= VENT TERMINAL X= AIR SUPPLY INLET = AREA WHERE TERMINAL IS NOT PERMITTED

Figure 4.4 Minimum Clearances for Termination

A = 12 inches.................clearances above grade, veranda,

porch, deck or balcony

B = 12 inches.................clearances to window or door

that may be opened, or to perma-

nently closed window. (Glass)

D* = 18 inches.................vertical clearance to unventilated

sofﬁ t or to ventilated sofﬁ t located

above the terminal

*30 inches ................for vinyl clad sofﬁ ts and below

electrical service

F = 9 inches..................clearance to outside corner

G = 6 inches...................clearance to inside corner

H = 3 ft. (Canada) ..........not to be installed above a gas

meter/regulator assembly within 3

feet (90 cm) horizontally from the

center-line of the regulator

I = 3 ft ...........................clearance to gas service regulator

vent outlet

J = 9 inches (U.S.A.)

12 inches (Canada) clearance to non-mechanical

air supply inlet to building or the

combustion air inlet to any other

appliance

K = 3 ft. (U.S.A.)

6 ft. (Canada) ...........clearance to a mechanical (pow-

ered) air supply inlet

CAUTION: IF EXTERIOR WALLS ARE FINISHED WITH VINYL SIDING, IT IS SUGGESTED THAT A VINYL PROTECTOR KIT BE INSTALLED.

** a vent shall not terminate directly above a sidewalk or paved driveway

which is located between two single family dwellings and serves both

dwellings.

*** only permitted if veranda, porch, deck or balcony is fully open on a

minimum of 2 sides beneath the ﬂ oor, or meets Note 2.

NOTE 1: On private property where termination is less than 7 feet above

a sidewalk, driveway, deck, porch, veranda or balcony, use of a listed cap

shield is suggested. (See vents components page)

NOTE 2: Termination in an alcove space (spaces open only on one side

and with an overhang) are permitted with the dimensions speciﬁ ed for

vinyl or non-vinyl siding and sofﬁ ts. 1. There must be 3 feet minimum

between termination caps. 2. All mechanical air intakes within 10 feet

of a termination cap must be a minimum of 3 feet below the termination

cap. 3. All gravity air intakes within 3 feet of a termination cap must be a

minimum of 1 foot below the termination cap.

(See Note 1)

(See Note 2)

NOTE 3: Local codes or regulations may require different

clearances.

NOTE 4: Termination caps may be hot. Consider their proximity to

doors or other trafﬁ c areas.

NOTE 5: Location of the vent termination must not interfere with

access to the electrical service.

WARNING: In the U.S: Vent system termination is NOT permitted in

screened porches. You must follow side wall, overhang and ground

clearances as stated in the instructions.

In Canada: Vent system termination is NOT permitted in screened

porches. Vent system termination is permitted in porch areas with

two or more sides open. You must follow all side walls, overhang

and ground clearances as stated in the instructions.

Heat & Glo assumes no responsibility for the improper performance

of the appliance when the venting system does not meet these

requirements.

Electrical

Service

V

S

VS

V

T

D*

V

MN

P

R

Q

N = 6 inches ..................non-vinyl sidewalls

12 inches ................vinyl sidewalls

P = 8 ft.

QMIN RMAX

1 cap 3 feet 2 x Q ACTUAL

2 caps 6 feet 1 x Q ACTUAL

3 caps 9 feet 2/3 x Q ACTUAL

4 caps 12 feet 1/2 x Q ACTUAL

QMIN = # termination caps x 3 RMAX = (2 / # termination caps) x QACTUAL

Alcove Applications

(See Note 1)

(See Note 5)

L** = 7 ft. ......................... clearance above paved

sidewalk or a paved driveway

located on public property

M*** = 18 inches................ clearance under veranda, porch,

deck, balcony or overhang

42 inches ............... vinyl

S = 6 inches................. clearance from sides of electri-

cal service

T = 12 inches................ clearance above electrical

service

Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 13

Fire Hazard.

Explosion Risk.

Asphyxiation Risk.

Do NOT connect this gas appliance to a chimney

ﬂ ue serving a separate solid-fuel or gas burning

appliance.

• Vent this appliance directly outside.

• Use separate vent system for this appliance.

May impair safe operation of this appliance or

other appliances connected to the ﬂ ue.

CAUTION

ALL vent conﬁ guration speciﬁ cations MUST be followed.

• This product is tested and listed to these speciﬁ cations.

• Appliance performance will suffer if speciﬁ cations are not

followed.

B. Use of Elbows

Diagonal runs have both vertical and horizontal vent as-

pects when calculating the effects. Use the rise for the

vertical aspect and the run for the horizontal aspect (see

Figure 5.1).

Two 45º elbows may be used in place of one 90º elbow. On

45º runs, one foot of diagonal is equal to 8.5 inches hori-

zontal run and 8.5 inches vertical run. A length of straight

pipe is allowed between two 45º elbows (see Figure 5.1).

Figure 5.1

5

5 Vent Information and Diagrams

A. Vent Table Key

The abbreviations listed in this vent table key are used in

the vent diagrams.

C. Measuring Standards

Vertical and horizontal measurements listed in the vent

diagrams were made using the following standards.

1. Pipe measurements are shown using the effective length

of pipe (see Figure 5.2).

2. Measurements are made from the appliance outer wrap,

not from the standoffs.

3. Horizontal terminations are measured to the outside

mounting surface (ﬂ ange of termination cap) (see

Figure 4.1).

4. Vertical terminations are measured to bottom of termi-

nation cap.

5. Horizontal pipe installed level with no rise.

Figure 5.2 DVP Pipe Effective Length

Effective

Height/Length

Symbol Description

V1First section (closest to appliance) of vertical length

V2Second section of vertical length

H1First section (closest to appliance) of horizontal length

H2Second section of horizontal length

Horizontal

Vertical

8-1/2 in.

12 in.

Pipe Effective Length

Inches Millimeters

DVP4 4 102

DVP6 6 152

DVP12 12 305

DVP24 24 610

DVP36 36 914

DVP48 48 1219

DVP6A 3 to 6 76 to 152

DVP12A 3 to 12 76 to 305

DVP12MI 3 to 12 76 to 305

DVP24MI 3 to 24 76 to 610

WARNING

Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/0714

3in.CLEARANCE TERMINATION

CAP

FLEX-VENT

1in.

CLEARANCE

D. Use of Flex Vent

The ﬂ ex vent must be supported with

the spacing between support intervals

not exceeding 4 feet, with no more

than ½ inch sag between supports.

A support is required at each change

in venting direction, and in any location

where it is necessary to maintain the

necessary clearance to combustibles.

A simple “up and out” installation (Fig-

ure 5.3) requires only enough support

to maintain the necessary clearance

to combustibles. However, the vent at-

tachment point and the ﬁ restop loca-

tion are considered to be supports.

Figure 5.3

Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 15

Figure 5.4

E. Vent Diagrams

1. Top Vent - Horizontal Termination Venting

V Minimum H1 Maximum

SL-350TRS-D SL-550, SL-750TRS-E

90º Elbow 1-1/2 ft. 457 mm 1 ft. 305 mm

1/2 ft. 152 mm 2 ft. 610 mm 2 ft. 610 mm

1-1/2 ft. 457 mm 3 ft. 914 mm 3 ft. 914 mm

2-1/2 ft. 762 mm 5 ft. 1-1/2 m 5 ft. 1-1/2 m

3-1/2 ft. 1.1 m 7 ft. 2.1 m 7 ft. 2.1 m

4-1/2 ft. 1.4 m 15 ft. 4.6 m 15 ft. 4.6 m

H1 Maximum= 15 ft. (4.6 m)

V1 + H1 Maximum= 40 ft. (12.2 m)

Note: Use SL-D Series

components only.

Note: There MUST be a 25%

reduction in total H when using

ﬂ ex vent except when using the

simple up and out installation

(see Figure 5.3).

Fire Risk. Explosion Risk.

Do NOT pack insulation or other combustibles between ceiling ﬁ restops.

• ALWAYS maintain speciﬁ ed clearances around venting and ﬁ restop systems.

• Install wall shield and ceiling ﬁ restops as speciﬁ ed.

Failure to keep insulation or other material away from vent pipe may cause ﬁ re.

WARNING

V1

H1

One Elbow

Fire Risk.

• When using SL-HRC-SS and SL-HRC-ZC-SS

termination caps on top vented ﬁ replaces, a one

foot minimum vertical vent section is required

before installing ﬁ rst elbow.

WARNING

Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/0716

H1

H2V1

Figure 5.5

Two Elbows

V Minimum H Maximum

SL-350TRS-D, SL-550TRS-E, SL-750TRS-E

90º Elbow NOT ALLOWED

1/2 ft. 152 mm 1 ft. 305 mm

1-1/2 ft. 457 mm 2 ft. 610 mm

2-1/2 ft. 762 mm 4 ft. 1.2 m

3-1/2 ft. 1.1 m 6 ft 1.8 m

4-1/2 ft. 1.4 m 14 ft. 4.3 m

H1 + H2 Maximum= 14 ft. (4.3 m)

V1 + H1 + H2 Maximum= 40 ft. (12.2 m)

Note: Use SL-D Series

components only.

Note: There MUST be a 25%

reduction in total H when using

ﬂ ex vent except when using the

simple up and out installation

(see Figure 5.3).

Fire Risk.

• When using SL-HRC-SS and SL-HRC-ZC-SS

termination caps on top vented ﬁ replaces, a one

foot minimum vertical vent section is required

before installing ﬁ rst elbow.

WARNING

Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 17

Figure 5.6

1. Top Vent - Horizontal Termination - (continued)

Three Elbows

H1

H2

V1

V2

V1 Minimum H1 Maximum H1 + H2 Maximum H1 Maximum H1 + H2 Maximum

Model: SL-350TRS-D Models: SL-550TRS-IPI-E, SL-750TRS-IPI-E

Elbow only 1-1/2 ft. 457 mm 2 ft. 610 mm 1 ft. 305 mm 2 ft. 610 mm

1/2 ft. 152 mm 2 ft. 610 mm 4 ft. 1.2 m 2 ft. 610 mm 4 ft. 1.2 m

1-1/2 ft. 457 mm 3 ft. 914 mm 6 ft. 1.8 m 3 ft. 914 mm 6 ft. 1.8 m

2-1/2 ft. 762 mm 5 ft. 1.5 m 10 ft 3.0 m 5 ft. 1.5 m 10 ft. 3.0 m

3-1/2 ft. 1.1 m 7 ft. 2.1 m 14 ft. 4.3 m 7 ft. 2.1 m 14 ft. 4.3 m

4-1/2 ft. 1.4 m 14 ft. 4.3 m 14 ft. 4.3 m 14 ft. 4.3 m 14 ft. 4.3 m

V1 + H1 + V2 + H2 Maximum = 40 ft. (12.2 m)

Note: Use SL-D Series

components only.

Note: There MUST be a 25%

reduction in total H when using

ﬂ ex vent except when using the

simple up and out installation

(see Figure 5.3).

Fire Risk.

• When using SL-HRC-SS and SL-HRC-ZC-SS

termination caps on top vented ﬁ replaces, a one

foot minimum vertical vent section is required

before installing ﬁ rst elbow.

WARNING

Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/0718

2. Top Vent - Vertical Termination

No Elbow

V1 = 44 ft. Max. (13.4 m)

Note: Use SL-D Series

components only.

Figure 5.8

INNER HEAT SHIELD

Top Vent Application

Rear Vent Application

Note: Be sure to re-

install the inner heat

shield after exhaust

restrictor installation.

Figure 5.7

CAP

V1

Exhaust restrictors are recommended for these verti-

cally terminated products which have excessive draft.

Exhaust restrictors will compensate for high draft, and

restore visual ﬂ ame height. If the vent conﬁ guration has

a total vertical of 15-44 feet, an exhaust restrictor may

be needed. The exhaust restrictor can be located in the

appliance manual bag.

Exhaust restrictor Instructions

1. Install the exhaust restrictor over the center of the ex-

haust outlet in the ﬁ rebox (see Figure 5.8).

2. Center the exhaust restrictor in the open end of the

exhaust outlet and secure through the slots on the ex-

haust restrictor with the 2-1/4 in. self tapping screws

provided in the appliance manual bag.

Exhaust restrictor

To access the

exhaust openings,

remove the inner

heat shield. To

remove inner heat

shield, remove the

two screws.

Note: If installing a vertical vent/termination off the top of

the appliance, the optional vertical termination bafﬂ e may

be needed.

Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 19

Figure 5.8

Two 90º Elbows

H1

V1

V2

V1 Minimum H1 Maximum H1 Maximum V2V1 + V2 Minimum

SL-350TRS-D SL-550TRS-E, SL-750TRS-E * *

90º Elbow 1-1/2 ft. 457 mm 1 ft. 305 mm * *

1/2 ft. 152 mm 2 ft. 610 mm 2 ft. 610 mm * *

1 ft. 305 mm 2-1/2 ft. 762 mm 2-1/2 ft. 762 mm * *

2 ft. 610 mm 4 ft. 1.2 m 4 ft. 1.2 m * *

3 ft. 914 m 6 ft. 1.8 m 6 ft. 1.8 m * *

4 ft. 1.2 m 8 ft. 2.4 m 8 ft. 2.4 m * *

5 ft. 1.5 m 15 ft. 4.6 m 15 ft 4.6 m * *

H1 Maximum= 15 ft. (4.6 m)

V1 + V2 + H Maximum = 40 ft. (12.2 m)

*No speciﬁ c restrictions on this value EXCEPT V1 + V2 + H1 CANNOT exceed 40 ft. (12.2 m)

Note: Use SL-D Series

components only.

Note: There MUST be a 25%

reduction in total H when using

ﬂ ex vent except when using the

simple up and out installation

(see Figure 5.3).

2. Top Vent - Vertical Termination - (continued)

Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/0720

Figure 5.9

2. Top Vent - Vertical Termination - (continued)

Three 90º Elbows

H1

H2V1

V2

ALL MODELS

V1 H

1+ H2 Maximum V2V1 + V2 Minimum

90º Elbow 0 0 1-1/2 ft. 457 mm 1-1/2 ft. 457 mm

1/2 ft.. 152 mm 1 ft. 305 mm * * * *

1-1/2 ft. 457 mm 2 ft. 610 mm * * * *

2-1/2 ft. 762 mm 4 ft. 1.2 m * * * *

3-1/2 ft. 1.1 m 6 ft. 1.8 m * * * *

4-1/2 ft. 1.4 m 14 ft. 4.3 m * * * *

H1 Maximum = 14 ft. (4.3 m)

*No speciﬁ c restrictions on this value EXCEPT V1 + V2 + H1 + H2

CANNOT exceed 40 ft. (12.2 m).

Note: Use SL-D Series

components only.

Note: There MUST be a 25%

reduction in total H when using

ﬂ ex vent except when using the

simple up and out installation

(see Figure 5.3).

Î

Page is loading ...

Hearth and Home Technologies SL-350TRS-D, SL-350TRS-IPI, SL-550TRS-IPI-E, SL-750TRS-IPI-E User manual

Related papers

Other documents