Robertshaw 5320 User manual

Brand: Robertshaw

Model: 5320

Category: Thermostats

Type: User manual

This manual is also suitable for

Detailed

Installer Guide

Programmable Touchscreen Thermostats

Speciﬁcations

Installation and Wiring

Quick Reference

Installer Settings

System Testing

To prevent damage to the thermostat, never use a sharp instrument

to press the touchscreen keys. Always press keys with your ﬁngers.

Attention

• Possible electric shock or damage to equipment can occur.

• Disconnect power before beginning installation.

Caution

This thermostat requires 24 Volt AC Power or 2 properly installed “AA” Alkaline

batteries for

proper operation. When connecting 24 Volt AC Power the batteries may

be installed as a backup.

For use only as described in this manual. Any other use will void warranty.

5310

Single Stage Heat / Cool Conventional

or Heat Pump

5320

Up to 4 Heat / 2 Cool Heat Pump

Up to 3 Heat / 2 Cool Conventional

Warning

For installation by experienced service technicians only.

Touchscreen

This thermostat is compatible with:

  • Singlestageheat/coolconventionalandheatpumpsystems

  • Conventionalsystemsupto3stagesofheatingand2stagesofcooling(5320only)

  • Heatpumpsystemsupto4stagesofheatingand2stagesofcooling(5320only)

  • 250–750millivoltheatingonlysystems

Electrical and control speciﬁcations:

  • ElectricalRating:24VoltAC

  • 1ampmaximumloadperterminal

  • ACPower:18–30VoltsAC

  • DCPower:3.0VoltDC(2“AA”AlkalineBatteriesIncluded)

  • ControlRange:45°–90°F(7°–32°C)

  • TemperatureAccuracy:+/-1°F(+/-.5°C)

  • OutdoorTemperatureDisplayRange:-40°-120°F(-40°-49°C)

Terminations

  • 5310:G,Rc,Rh,W1,O/B,Y1,C,S1,S2

  • 5320:A,G,Rc,Rh,W1/E/AUX1,W2/AUX2,W3/O/B,Y1,Y2,C,L,S1,S2

Speciﬁcations

5310W-100-04

Model number is located on back of thermostat.

Thermostat Location

Installthethermostatapproximately5feet(1.5m)abovetheoorinanareathathasagoodamountofair

circulationandmaintainsanaverageroomtemperature.

Avoidinstallationinlocationswherethethermostatcanbeaffectedbydrafts,deadairspots,hotorcoldair

ducts,sunlight,appliances,concealedpipes,chimneysandoutsidewalls.

Installer Guide 2

Install your new Braeburn thermostat in 4 basic steps:

1 InstalltheSub-Base

2 ProvidePower

3 ConnectYourWires

4 AttachThermostattoSub-Base

Install the Sub-Base:

•Removethesub-basefromthebodyofthethermostat.

•Mountthesub-baseasshownbelow:

Warning

Disconnect power before beginning installation.

Installation and Wiring

Drill 3/16” pilot holes in your

desired location. Use supplied

anchors for drywall or plaster.

3 Installer Guide

Provide Power

24VAC Power Terminal (C)

Wiring Terminations for model 5310

Terminal Function Description

 G Output FanControl

 Rc Input 24VoltACCoolingTransformer

   (DualTransformerSystemsOnly)

 Rh Input PowerConnection(24VoltACHeating

   TransformerorMillivoltPowerSource)

 W1 Output ConventionalHeatRelay

 O/B Output ReversingValve(CoolActiveorHeatActive)

 Y1 Output CompressorRelay

 C Input 24VoltACTransformerCommon

 S1

 S2

Connect Your Wires

Input OptionalRemoteSensor(indoororoutdoor)

• For24VoltACpower,youmustconnectthecommonsideofthetransformertotheCterminalonthethermostatsub-base.In

 dualtransformerinstallations,thetransformercommonmustcomefromthecoolingtransformer.

• Forbatterypower,insertthe2supplied“AA”typealkalinebatteriesintothebatterycompartmentlocatedintherear

 housingofthethermostat.MakesuretopositionthePositive(+)andNegative(-)sidesofthebatteriescorrectlywith

 the+/-symbolsinthebatterycompartment.

Batteries Installed as Shown

Installer Guide 4

Wiring Terminations for model 5320

Terminal Function Description

 A Output EconomizerControl

  G Output FanControl

  Rc Input 24VoltACCoolingTransformer

    (DualTransformerSystemsOnly)

  Rh Input PowerConnection(24VoltACHeating  

    TransformerorMillivoltPowerSource)

 W1/E/ Output (W1)1stStageConventionalHeat,

 AUX1  (E)EmergencyHeat,    

(AUX1)1stStageAuxiliaryHeat

 W2/AUX2 Output (W2)2ndStageConventionalHeat,  

    (AUX2)2ndStageAuxHeat

 W3/O/B Output (W3)3rdStageConventionalHeat,  

    (O)CoolActiveReversingValve   

    (B)HeatActiveReversingValve

  Y1 Output 1stStageCompressor

  Y2 Output 2ndStageCompressor

  C Input 24VoltACTransformerCommon

  L Input SystemMalfunctionIndicator

  S1

  S2

Connecting Your Wires (continued)

Input OptionalRemoteSensor(indoororoutdoor)

5 Installer Guide

1 HEAT / 1 COOL Single or Dual Transformer

Set System Type to 11CONV

24VoltACPower(heatingtransformer)[note 2]

24VoltACPower(coolingtransformer)[note 2]

W1 HeatRelay

Y1 CompressorRelay

G FanRelay

C 24VoltACTransformerCommon[note 1, 3]

NOTES - Conventional Systems

[1]Optional24VoltACcommonconnection.

[2]Removefactoryinstalledjumperfordual

 transformersystems.Providedisconnectand

 overloadprotectionasrequired.

[3]Indualtransformersystems,transformer

 commonmustcomefromcoolingtransformer.

[4]Ifneededforsystem.

Provide disconnect and overload protection as required.

3 HEAT / 2 COOL Single or Dual Transformer

Set System Type to 32CONV

24VoltACPower(heatingtransformer)[note 2]

24VoltACPower(coolingtransformer)[note 2]

W1 HeatRelayStage1

W2 HeatRelayStage2

W3 HeatRelayStage3

Y1 CompressorRelayStage1

Y2 CompressorRelayStage2 [note 4]

G FanRelay

C 24VoltACTransformerCommon[note 1, 3]

2 HEAT / 2 COOL Single or Dual transformer

Set System Type to 22CONV

24VoltACPower(heatingtransformer)[note 2]

24VoltACPower(coolingtransformer)[note 2]

W1 HeatRelayStage1

W2 HeatRelayStage2

Y1 CompressorRelayStage1

Y2 CompressorRelayStage2 [note 4]

G FanRelay

C 24VoltACTransformerCommon[note 1, 3]

Typical Wiring Conﬁgurations

NOTE: The “System Type” option will be conﬁgured in the Installer Settings section. The 5310 is a single stage

thermostat and not intended for multi stage equipment.

Conventional Systems

NOTE: Additional options are conﬁgured in the

Installer Settings section.

A EconomizerControl(5320only)[note 2]

NOTES - Additional Wiring Options

[1]Theseterminalscanbeusedtoconnecta

 Braeburn

indoororoutdoorremotesensor.

[2]

Thisterminalcanbeusedforeconomizer

 control(5320).

Additional Wiring Options

IndoororOutdoorRemoteSensor[note 1]

Heat Only or Millivolt

Set System Type to 11CONV

Rh PowerConnection

W1 HeatRelay

G FanRelay[note 4]

C 24VoltACTransformerCommon[note 1]

Installer Guide 6

1 HEAT / 1 COOL - No Auxiliary Heat

Set System Type to 11HP

Rh 24VoltACPower

Rc ConnectedtoRhwithsuppliedJumperWire

O/B

ChangeoverValve [note 2]

Y1 CompressorRelay(appearsasYonthe5310)

G FanRelay

C 24VoltACTransformerCommon [note 1]

3 HEAT / 2 COOL – Including Auxiliary Heat

Set System Type to 32HP

Rh 24VoltACPower

ConnectedtoRhwithsuppliedJumperWire

O/B ChangeoverValve [note 2]

Compressor1Relay(1ststageheating/cooling)

Compressor2Relay(2ndstageheating/cooling)

AUX1

AuxiliaryHeatRelay(3rdstageheating)[note 5]

G FanRelay

C 24VoltACTransformerCommon[note 1]

L OptionalSystemFaultMonitor[note 4]

2 HEAT / 1 COOL - Including Auxiliary Heat

Set System Type to 22HP

Rh 24VoltACPower

Rc ConnectedtoRhwithsuppliedJumperWire

O/B

ChangeoverValve[note 2]

Y1 CompressorRelay(1ststageheating/cooling)

AuxiliaryHeatRelay(2ndstageheating)[note 3]

E EmergencyHeatRelay[note 3]

G FanRelay

C 24VoltACTransformerCommon[note 1]

L OptionalSystemFaultMonitor[note 4]

2 HEAT / 2 COOL - No Auxiliary Heat

Set System Type to 32HP

Rh 24VoltACPower

Rc ConnectedtoRhwithsuppliedJumperWire

O/B

ChangeoverValve[note 2]

Compressor1Relay(1ststageheating/cooling)

Compressor2Relay(2ndstageheating/cooling)

G FanRelay

C 24VoltACTransformerCommon[note 1]

L OptionalSystemFaultMonitor[note 4]

4 HEAT / 2 COOL - Including Auxiliary Heat

Set System Type to 42HP

Rh 24VoltACPower

Rc ConnectedtoRhwithsuppliedJumperWire

O/B ChangeoverValve[note 2]

Compressor1Relay(1ststageheating/cooling)

Compressor2Relay(2ndstageheating/cooling)

AUX1

AuxiliaryHeatRelay1(3rdstageheating)[note 5]

AUX2

AuxiliaryHeatRelay2Relay(4thstageheating)

G FanRelay

C 24VoltACTransformerCommon[note 1]

L OptionalSystemFaultMonitor[note 4]

NOTES - Heat Pump Systems

[1] Optional24VoltACcommonconnection.

[2] O(coolactive)orB(heatactive)isselectedin

 theInstallerSettingsmenu.

[3] Installaeldsuppliedjumperbetweenthe

 W2/AUX2andW1/E/AUX1terminalsifthereis

 noseparateemergencyheatrelayinstalled.

[4] IftheLterminalisused,the24VoltACcommon

 mustbeconnected(Cterminal).

[5] Ifaseparateemergencyheatrelayisinstalled,the

 W1/E/AUX1terminalshouldhaveboththeauxiliary

 heat1relayandemergencyheatrelayconnected.

Provide disconnect and overload protection as required.

Typical Wiring Conﬁgurations

NOTE: The “System Type” option will be conﬁgured in the Installer Settings section. The 5310 is a single

stage thermostat and not intended for multi stage equipment.

Heat Pump Systems

7 Installer Guide

NOTE: This thermostat ships conﬁgured as a 1H/1C conventional

thermostat. Conﬁrm installer settings. See page 10.

W1/E

/AUX1

W2/

AUX2

W3/

O/B

W1/E

AUX

Attach Thermostat to Sub-Base

3) InsertQuickReferenceCardintoslot

 ontopofthermostat.

1) Lineupthethermostatbodywiththesub-base.

2) Carefullypushthethermostatbodyagainstthe

 sub-baseuntilitsnapsinplace.

NOTE: Additional options are conﬁgured in the

Installer Settings section.

A EconomizerControl(5320only)[note 2]

NOTES - Additional Wiring Options

[1]Theseterminalscanbeusedtoconnecta

 Braeburn

indoororoutdoorremotesensor.

[2]

Thisterminalcanbeusedforeconomizer

 control(5320).

Additional Wiring Options

IndoororOutdoorRemoteSensor[note 1]

Installer Guide 8

Room Temperature...................... Displaysthecurrentroomtemperature

Lock Mode Indicator ................... Indicatesifthethermostatislocked

Set Temperature.......................... Displaysthecurrentsetpointtemperature

Service Indicators ...................... Displaysvariousservice/maintenanceinformation

Time of Day .................................Displaysthecurrenttimeofday

Program Event Indicator.............. Displaystheprogramevent

Day of the Week........................... Displaysthecurrentdayoftheweek

System Status Indicator ............. Displaysinformationaboutthestatusofthesystem

Hold Mode Indicator ................... IndicatesifthethermostatisinHOLDmode

Fan Indicator................................ Indicateswhenthesystemfanisrunning

Low Battery Indicator.................. Indicateswhenthebatteriesneedtobereplaced

Quick Reference Instructions...... Storedinslotlocatedattopofthermostat

SpeedBar

...................................Increasesordecreasessettings(time,temperature,etc.)

Reset Button ...............................Resetscurrenttime,programandusersettings

Battery Compartment ................. Locatedinthebackofthermostat

Quick Reference

Thermostat Display

Thermostat

9 Installer Guide

Thermostat TouchPads

NOTE: Thermostat TouchPads are located on the left, right and bottom portions of the display screen. They are

the “touch sensitive” segments used to adjust your thermostat. Depending on the equipment installed, all touch

pads may not show.

SYSTEM......SelectsAUTO(Heat/Cool),COOL,OFFHEATorEMER(EmergencyHeat)

FAN.............SelectsAUTO,ON,CIRC(Circulation)andPROG(Program)fanmodes

PROG..........Selectsprogrammingmodeorpressfor3secondstoselectSpeedSet

mode

HOLD..........Enters/ExitstheHOLDmode(programbypass)

DAY/TIME...Setsthecurrenttimeanddayoftheweek

BACK..........Movesbackinsettingandprogrammingmodes

NEXT...........Movesforwardinsettingandprogrammingmodes

RETURN......Returnstonormalmodefromprogramorsettingsmodes

CONFIG.......EnterstheUserandInstallersettingsmodes

CLEAN........Entersabriefscreencleaningmode

Outdoor Temperature

IfaBraeburn

outdoortemperaturesensorwasconnected,youmaytouchtheroomtemperatureareaofthe

screentoviewtheoutdoortemperature.

TheInstallerSettingsmustbeproperlyconguredinorderforthisthermostattooperatecorrectly.TheInstaller

Settingsaremenudriven.Theportionofthesesettingsthatdonotapplytoyoursetupwillbeskipped.These

settingsareindicatedbelowwithcomments.Moredetailoneachsettingfollowsthistable.

Installer Guide 10

1. TouchandholddowntheSYSTEMandCONFIGTouchPadsfor3seconds.

2. Releasebothbuttonsandtherstinstallersettingwillbedisplayed.

3. ChangesettingsasrequiredusingtheUPorDOWNportionoftheSpeedBar

4. TouchNEXTorBACKtomovetothenextorprevioussetting,touchRETURNtoexit.

NOTE: Shaded areas below do not apply to the 5310.

No. Installer Setting Factory Setting Comments

(Notes follow this table) Default Options (More information follows this table)

1  Residentialor RES RES SelectforResidentialprole

  orCommercialProle    COMM SelectforCommercialprole

2  ProgrammingMode 7 PROG 7 PROG Selectfor7dayprogrammingmode

[note 1] 52 PROG Selectfor5-2dayprogrammingmode

NO PROG Selectfornon-programmablemode

3  ClockFormat 12 HR 12 HR Selectfor12hourclock

24 HR Selectfor24hourclock

4  TemperatureScale F DEG F DEG SelectforFahrenheitdisplay

C DEG SelectforCelsiusdisplay

5  AutoChangeover oF AUTO oF AUTO DisablesAutoChangeovermode

ON AUTO EnablesAutoChangeovermode

11CONV Selectfor1H/1CConventionalsystem

22CONV Selectfor2H/2CConventionalsystem

32CONV Selectfor3H/2CConventionalsystem

6  SystemType 11CONV 11HP Selectfor1H/1CHeatPumpsystem

22HP Selectfor2H/2CHeatPumpsystem

32HP Selectfor3H/2CHeatPumpsystem

42HP Selectfor4H/2CHeatPumpsystem

7  1stStageDifferential 0.5 DIF1 0.5, 1.0or Selecta1ststagetemperaturedifferentialof.5°,

2.0 DIF1 1°or2°F(.25°,.5°or2°C)

8  2ndStageDifferential 2.0 DIF2 1.0, 2.0, 3.0, Selecta2ndstagetemperaturedifferentialof1°,

[note 2] 4.0, 5.0or 2°,3°,4°,5°or6°F(.5°,1°,1.5°,2°,2.5°or3°C)

6.0 DIF2

9  3rdStageDifferential 2.0 DIF3 1.0, 2.0, 3.0, Selecta3rdstagetemperaturedifferentialof1°,2°,

[note 2] 4.0, 5.0or 3°,4°,5°or6°F(.5°,1°,1.5°,2°,2.5°or3°C)

6.0 DIF3

10 4thStageDifferential 2.0 DIF4 1.0, 2.0, 3.0,

Selecta4thstagetemperaturedifferentialof1˚,

[note 2] 4.0, 5.0or 2°,3°,4°,5°or6°F(.5°,1°,1.5°,2°,2.5°or3°C)

6.0 DIF4

Installer Settings

11 Installer Guide

No. Installer Setting Factory Setting Comments

(

Notes follow this table) Default Options (More information follows this table)

 11 1stStageFanControl HG FAN 1 HG FAN 1 Selectfor1ststageGasheating

[note 3] HE FAN 1 Selectfor1ststageElectricheating

 12 EmergencyHeat] HE EMER HE EMER SelectforElectricEmergencyHeat

FanControl[note 4] HG EMER SelectforGasEmergencyHeat

 13 ReversingValve REVO REVO SelectforcoolactiveReversingValve(Oterminal)

  (O/BTerminal)[note 5] REVB SelectforheatactiveReversingValve(Bterminal)

 14 FossilFuel AE AUX AE AUX SelectforElectricAuxiliaryheat(withcompressor)

BackupHeat[note 4] AG AUX SelectforGasAuxiliaryheat(withoutcompressor)

 15

CompressorPowerOutage

oF CPOP oF CPOP DisablesPowerOutageLockoutDelay

Protection [notes 4, 6] on CPOP EnablesPowerOutageLockoutDelay

 16 ACPowerInterrupt

AC oF MONR

AC oF MONR DisablesACPowerInterruptWarning

Warning[note 6] AC on MONR EnablesACPowerInterruptWarning

 17 CompressorShort 5 CSCP 5, 4, 3, 2or Selectacompressorshortcycleprotectiondelayof5, 

  CycleProtection   0 CSCP  4,3,2or0minutes

 18 ResidualCooling 60 FAN 90, 60, 30  SelectaResidualCoolingFanDelayof90,60,

FanDelay or0 FAN 30or0seconds.

 19 CirculatingFanLock oF CIRC oF CIRC DisablesCirculatingFanLockmode

on CIRC EnablesCirculatingFanLockmode

 20 AdaptiveRecovery oF REC oF REC DisablesAdaptive(early)Recoverymode

Mode(ARM™) [note 7] on REC EnablesAdaptive(early)Recoverymode

 21 IndoorRemoteSensor I SENS I SENS Temperatureissensedfromthermostatonly.

Control*[note 8] E SENS Temperatureissensedfromremotesensoronly.

A SENS Temperatureiscombinedwiththethermostatand 

        theremotesensor.

 22 LockoutSecurityLevel 2 LOCK 2 LOCK Iflocked–Completelockoutisenabled

1 LOCK Iflocked–Partiallockoutisenabled(SpeedBar

is 

        stillfunctional)

 23 AutoChangeover 3 BAND 2, 3, 4or5 SelectaDeadBandof2°,3°,4°or5˚F  

DeadBand[note 9] BAND (1°,2°or3°C)forAutoChangeovermode.

24 CompressorBalance NO BALC NO BALC DisablesBalancePoints

Point[notes 4, 10] 15-50 BALC SelectaCompressorBalancePointof15°-50°F

(-9°-10°C)

25 AuxiliaryHeatBalance NO BALA NO BALA DisablesBalancePoints

Point[notes 4, 10]

70-40 BALA

SelectaAuxiliaryHeatBalancePointof70°-40°F

(21°-4°C)

26 OutsideAirIntake OA NONE OA NONE DisablesOutsideAirIntakeoption

(ATerminal)[note 11] OA ECON EnablesOutsideAirIntake(EconomizerMode)

OA TOD EnablesOutsideAirIntake(TimeofDayMode)

 27

HeatSetPointUpperLimit

90LIM 90-60 LIM

SelectaHeatSetPointUpperLimitof90°-60°F(32°-10°C)

28

CoolSetPointLowerLimit

45LIM 45-80 LIM

SelectaCoolSetPointLowerLimitof45°-80°F(7°-27°C)

*WhenaBraeburn

outdoorsensorisconnected,thethermostatautomaticallyrecognizesit.Pressroomtemperaturedigitsto

displayoutdoortemperature.

NOTE: Additional options such as Service Monitors, Setting the lock code, audible tone, etc. are located in the

User Settings – See User manual for information on setting these options.

Installer Guide 12

NOTES - Installer Settings

1 OnlyavailableifResidentialprolewasselectedinoption1.

2 Onlyavailableifa2,3or4stagesystemtypewasselectedinoption6.

3 OnlyavailableifaConventionalsystemwasselectedinoption6.

4 Onlyavailableifa2,3or4stageHeatPumpsystemwasselectedinoption6.

5 OnlyavailableifaHeatPumpsystemwasselectedinoption6.

6 Onlyavailableifthe24VoltACcommonwireisconnectedtotheCterminal.

7 Onlyavailableifaprogrammableprolewasselectedinoption2.

8 OnlyavailableifaBraeburn®indoorremotesensorwasconnected.

9 Onlyavailableifautochangeoverwasenabledinoption5.

10 OnlyavailableifaBraeburnoutdoorsensorwasconnected.

11 OnlyavailableifCommercialprolewasselectedinoption1.

Detailed Explanation of Installer Settings (also see NOTES above):

1 Proﬁle–Selectsaresidential(RES)orcommercial(COMM)prole.Ifresidentialisselected,4programming

 eventsperdayareavailable.Ifcommercialisselected,2event,7dayprogrammingisavailable.

2 Programming Mode [note 1]–Selectstheprogrammingmode,eitherfull7dayor5-2day(weekday/

 weekend)programmingornon-programmable.

3 Clock Type–Selectseithera12houror24hourclock.

4 Temperature Scale–Selectsatemperaturescaleofeither°For°C.

5 Auto Changeover–Selectsautochangeoveronoroff.Whenautochangeovermodeisenabledand

 selected,thesystemautomaticallyswitchesbetweenheatingandcoolingmodes.Thereisa5minutedelay

 whenswitchingfromheatingtocoolingorcoolingtoheatinginautochangeovermode.

NOTE: Also see “Auto Changeover Dead Band” in option 23.

6 System Type–Selectsthesystemtypeforyourinstallation.NOTE: Changes made to this option will reset

options 7 through 15 back to their default values dependant on the system type.

7 1st Stage Differential–Selectsa1ststagetemperaturedifferential.

8 2nd Stage Differential [note 2]–Selectsa2ndstagetemperaturedifferential.

9 3rd Stage Differential [note 2]–Selectsa3rdstagetemperaturedifferential.

10 4th Stage Differential [note 2]–Selectsa4thstagetemperaturedifferential.

11 1st Stage Fan Control [note 3]–Selectsa1ststagefancontrolofeithergasorelectricheat.

12 Emergency Heat Fan Control [note 4]–Selectsemergencyheatfancontrolofeithergasorelectricheat.

13 Reversing Valve [note 5]–SelectstheoutputstateoftheO/Bterminal.SelectOforthisterminaltobe

 activeinthecoolmodeorselectBforthisterminaltobeactiveintheheatmode.

14 Auxiliary Fossil Fuel Heat Pump Control [note 4]–Whensettoelectric(AEAUX),boththecompressor

 (1ststage)andauxiliarystage(s)willrunwhenacallforauxiliaryheatismade.Whensettogas(AGAUX),

 thecompressorstage(s)willbelockedoutoneminuteafteracallforauxiliaryheat.NOTE: This option can

be overridden if setting an auxiliary heat balance point in Option 25.

15 Compressor Power Outage Protection [notes 4, 6]–Selectspoweroutageprotectiononoroff.When

 enabled,thisthermostatwillprovidecoldweathercompressorprotectionbylockingoutthecompressor

 stage(s)ofheatingforaperiodoftimeafterapoweroutagegreaterthan60minutes.

13 Installer Guide

16 AC Power Interrupt Warning [note 6]–Whenenabled,thethermostatwilldisplayanoutagewarning

 whenACpowertothethermostatislost.

17 Short Cycle Protection–Selectsthenumberofminutesthecoolingcompressorwillbelockedoutafter

 turningoff.Thisshortcycleprotectionisalsoactiveintheheatmodeifaheatpumpsystemwasselectedin

 Option6.

18 Residual Cooling Fan Delay–Selectsadelayforthesystemfanafterthecoolingcompressorhasturned

 off.Thisdelaywillhelpremovetheremainingcoolairoutoftheductworkprovidingadditionalefciency.

19 Circulating Fan Lock–Whenenabled,theonlyuserfanoptionsavailableareONandCIRC(Circulation).

 TheAUTOoptionisnotavailablewiththisoptionenabled.

20 Adaptive Recovery Mode (early recovery) [note 7]–EnablesordisablestheARM

(adaptiverecovery

 mode)feature.DuringARM,roomtemperatureisrecoveredbyturningontheheatingorcoolingbeforethe

 endofthesetbackperiod.Thesetpointtemperatureischangedtothatoftheupcomingprogramtemperature.

21 Indoor Remote Sensor Control [note 8]–IfaBraeburn

indoorremotesensorisconnectedduring

 installation,thethermostatwillautomaticallydetectthesensor.Whenanindoorsensorisdetected,youmay

 selectbetweenthermostatonly(ISENS),remotesensoronly(ESENS)orcombiningthethermostatandthe

 remotesensor(ASENS).NOTE: This option does not apply to a Braeburn outdoor sensor. When an outdoor

sensor is connected the thermostat automatically recognizes it and no further conﬁguration is necessary.

22 Lockout Security Level–Selectsthelevelofkeypadlockoutwhenthethermostatislocked.Level2locks

theentirethermostat(includingthefrontresetbutton).Level1lockseverythingexcepttheSpeedBar

 allowingforupanddowntemperatureadjustment.NOTE: The lock code is set in the User Settings mode

(see User Manual).

23 Auto Changeover Dead Band [note 9]–Whenautochangeovermodeisenabledinoption5and

 selected,thesystemautomaticallyswitchesbetweenheatingandcoolingwhentheroomtemperature

 meetsthenormalcriteriaforeitheraheatingorcoolingcall.Thereisaforcedseparation(deadband)

 betweentheheatingandcoolingsetpointssothatthesystemsdonotworkagainsteachother.This

 optionselectstheamountofthisdeadbandindegreeswiththedefaultbeing3°F.

24 Compressor Balance Point [notes 4, 10]–Locksouttheuseofthecompressorheatstagewhenthe

 outsideairtemperatureislessthantheselectedsettingof15°Fto50°F(-9°Cto10°C)

25 Auxiliary Heat Balance Point [notes 4, 10]–Locksouttheuseoftheauxiliaryheatstagewhenthe

 outsideairtemperatureexceedstheselectedsettingof70°Fto40°F(21°Cto4°C).NOTE: This balance

point overrides the fossil fuel compressor lockout in option 14. If this option is set to gas and the outdoor

temperature is over the auxiliary balance point, the compressor will remain on during a call for auxiliary heat.

Installer Guide 14

26 Outside Air Intake [note 11]–Selectseconomizercontroloptions.Selectbetweendisabled(NONE),

 economizermode(ECON)andtimeofday(TOD)mode.

Time Step / Override Cooling Call

Occupied YES or NO ON ON OFF

YES ON OFF OFF

NO OFF OFF OFF

Override YES or NO ON ON OFF

External Air Output (A)

Economizer Time of Disabled

Mode Day Mode

Time Step / Override Heating Call

Occupied YES or NO ON ON OFF

YES OFF OFF OFF

NO OFF OFF OFF

Override YES or NO ON ON OFF

External Air Output (A)

Economizer Time of Disabled

Mode Day Mode

Unoccupied

27 Heat Set Point Upper Limit–Selectstheheatingsetpointupperadjustmentlimit.

28 Cool Set Point Lower Limit–Selectsthecoolingsetpointloweradjustmentlimit.

15 Installer Guide

Warning

Read Before Testing

• Donotshort(orjumper)acrossterminalsonthegasvalveorattheheatingorcoolingsystemcontrolboard

 totestthethermostatinstallation.Thiscoulddamagethethermostatandvoidthewarranty.

• DonotselecttheCOOLmodeofoperationiftheoutsidetemperatureisbelow50ºF(10ºC).Thiscould

 possiblydamagethecontrolledcoolingsystemandmaycausepersonalinjury.

• Thisthermostatincludesanautomaticcompressorprotectionfeaturetoavoidpotentialdamagetothe

 compressorfromshortcycling.Whentestingthesystem,makesuretotakethisdelayintoaccount.

NOTE: The compressor delay can be bypassed by pressing the reset button on the front of the thermostat.

All user settings will be returned to factory default, however all Installer settings will remain as originally

programmed in section 4.

1 TouchtheSYSTEMTouchPaduntilthethermostatisinHEATmode.

2 UsingtheSpeedBar®raisethesettemperatureaminimumof3degreesabovethecurrentroom 

 temperature.Thesystemshouldstartwithinafewseconds.Withagasheatingsystem,thefanmay

 notstartrightaway.

3 TouchSYSTEMuntilthethermostatisintheOFFmode.Allowtheheatingsystemtofullyshutdown.

4 TouchSYSTEMuntilthethermostatisintheCOOLmode.

5 UsingtheSpeedBarlowerthesettemperatureaminimumof3degreesbelowthecurrentroom 

 temperature.Thesystemshouldstartwithinafewseconds(unlesscompressorshortcycleprotection

 isactive–Seenoteabove).

6 TouchSYSTEMuntilthethermostatisintheOFFmode.Allowthecoolingsystemtofullyshutdown.

7 TouchFANuntilthethermostatisinFANONmode.Thesystemfanshouldstartwithinafewseconds.

8 TouchFANuntilthethermostatisinFANAUTOmode.Allowthesystemfantoturnoff.

9 Ifthethermostatiscontrollingauxiliaryequipmentsuchasaneconomizer(5320only),etc.,adjustthe

 thermostatsettingstotestthesedevices.

System Testing

Store this manual for future reference.

Limited Warranty

Wheninstalledbyaprofessionalcontractor,thisproductisbackedbya5yearlimited

warranty.Limitationsapply.Forlimitations,termsandconditions,youmayobtainafull

copyofthiswarranty:

·Visitusonline:www.braeburnonline.com/warranty

·Phoneus:866.268.5599

·Writeus:BraeburnSystemsLLC

2215CornellAvenue

Montgomery,IL60538

YEAR

WARRANT

LIMITED

BraeburnSystemsLLC

2215CornellAvenue•Montgomery,IL60538

TechnicalAssistance:www.braeburnonline.com

Callustoll-free:866-268-5599(U.S.)

630-844-1968(OutsidetheU.S.)

5310W-100-04

Robertshaw 5320 User manual

Brand: Robertshaw

Model: 5320

Category: Thermostats

Type: User manual

This manual is also suitable for

Download PDF

report

Robertshaw 5320 User manual

This manual is also suitable for

Robertshaw 5320 User manual

Related papers

Other documents