Robertshaw Braeburn 7300 7305 Thermostat User manual

Brand: Robertshaw

Model: Braeburn 7300 7305 Thermostat

Category: Thermostats

Type: User manual

Installer Guide

Universal Programmable Smart Wi-Fi Thermostats

Speciﬁcations

Installation and Wiring

Quick Reference

Installer Settings

System Testing

• Possible electric shock or damage to equipment can occur.

• Disconnect power before beginning installation.

Caution

This thermostat requires 24 Volt AC Power or 2 properly installed “AA” Alkaline

batteries for

proper operation. If connecting this thermostat to a Wi-Fi network,

a 24 VAC common (C wire) is required.

For use only as described in this manual. Any other use will void warranty.

7300

Single Stage Heat / Cool

Conventional or Heat Pump

7305

Up to 3 Heat / 2 Cool Heat Pump

Up to 2 Heat / 2 Cool Conventional

Warning

For installation by experienced service technicians only.

This thermostat is compatible with:

  • Singlestageheat/coolconventionalandheatpumpsystems

  • Conventionalsystemsupto2stagesofheatingand2stagesofcooling(7305only)

  • Heatpumpsystemsupto3stagesofheatingand2stagesofcooling(7305only)

  • 2or3wirehydroniczonesystems

Electrical and control speciﬁcations:

  • ElectricalRating:24VoltAC

  • 1ampmaximumloadperterminal

  • ACPower:18–30VoltsAC

  • DCPower:3.0VoltDC(2“AA”AlkalineBatteriesIncluded)

  • ControlRange:45°–90°F(7°–32°C)

  • TemperatureAccuracy:+/-1°F(+/-.5°C)

  • OutdoorTemperatureDisplayRange:-40°-120°F(-40°-49°C)

Terminations

  • 7300:Rc,Rh,W1,C,Y1,K,O/B/V3,G,S2,S1

  • 7305:Rc,Rh,W2,W1/E/W3,A,C,L,Y2,Y1,K,O/B/V3,G,S2,S1

Speciﬁcations

7300-100-02

Model number is located on back of thermostat.

See Wi-Fi Setup Guide for Wi-Fi Setup Instructions

“C” Common

Wire Required

for Wi-Fi

Thermostat Location

Installthethermostatapproximately5feet(1.5m)abovetheoorinanareathathasagoodamountofair

circulationandmaintainsanaverageroomtemperature.

Avoidinstallationinlocationswherethethermostatcanbeaffectedbydrafts,deadairspots,hotorcoldair

ducts,sunlight,appliances,concealedpipes,chimneysandoutsidewalls.

Installer Guide 2

Install your new Braeburn thermostat in 4 basic steps:

1 InstalltheSub-Base

2 ProvidePower

3 ConnectYourWires

4 AttachThermostattoSub-Base

Install the Sub-Base:

•Removethesub-basefromthebodyofthethermostat.

•Mountthesub-baseasshownbelow:

Warning

Disconnect power before beginning installation.

Installation and Wiring

Drill 3/16” pilot holes in your

desired location. Use supplied

anchors for drywall or plaster.

3 Installer Guide

Provide Power

24VAC Power Terminal (C)

Wiring Terminations for model 7300

Terminal Function Description

 Rc Input 24VoltACCoolingTransformer

   (DualTransformerSystemsOnly)

 Rh Input PowerConnection(24VoltAC

HeatingTransformer)

GOutput FanControl

 W1Output ConventionalHeatRelay

O/B/V3 Output (O)CoolActiveReversingValve   

   (B)HeatActiveReversingValve

   (V3)ZoneValvePowerClose

 Y1 Output CompressorRelay

 C Input 24VoltACTransformerCommon

K  - OptionalShare-a-Wire

     moduleconnection

 S1

 S2

Connect Your Wires

Input OptionalRemoteSensor(indoororoutdoor)

• For24VoltACpower,youmustconnectthecommonsideofthetransformertotheCterminalonthethermostat

 sub-base.Indualtransformerinstallations,thetransformercommonmustcomefromthecoolingtransformer.

•Forbatterypower,insertthe2supplied“AA”typealkalinebatteriesintothebatterycompartmentlocatedintherear

 housingofthethermostat.MakesuretopositionthePositive(+)andNegative(-)sidesofthebatteriescorrectlywith

 the+/-symbolsinthebatterycompartment.

• If connecting this thermostat to a Wi-Fi network, a 24 VAC common (C wire) is required.

Batteries Installed as Shown

Installer Guide 4

Wiring Terminations for model 7305

Terminal Function Description

  Rc Input 24VoltACCoolingTransformer

    (DualTransformerSystemsOnly)

  Rh Input PowerConnection(24VoltAC  

    HeatingTransformer)

G Output FanControl

W1/E/W3 Output (W1)1stStageConventionalHeat,

   (E)EmergencyHeat,    

(W3)3rdStageAuxiliaryHeat

   W2 Output 2ndStageConventionalHeat  

 O/B/V3 Output (O)CoolActiveReversingValve   

    (B)HeatActiveReversingValve

    (V3)ZoneValvePowerClose

  Y1 Output 1stStageCompressor

  Y2 Output 2ndStageCompressor

  L Input SystemMalfunctionIndicator

  A Output Economizer,FreshAirorOutputControl

C Input 24VoltACTransformerCommon

  K - OptionalShare-a-Wire

    moduleconnection

  S1

  S2

Connecting Your Wires (continued)

Input OptionalRemoteSensor(indoororoutdoor)

5 Installer Guide

Heat Only

Set System Type to 11CONV

Rh PowerConnection

W1 HeatRelay

G FanRelay[note 4]

C 24VoltACTransformerCommon[note 1]

1 HEAT / 1 COOL Single or Dual Transformer

Set System Type to 11CONV

24VoltACPower(heatingtransformer)[note 2]

24VoltACPower(coolingtransformer)[note 2]

W1 HeatRelay

Y1 CompressorRelay

G FanRelay

C 24VoltACTransformerCommon[note 1, 3]

NOTES - Conventional Systems

[1]Optional24VoltACcommonconnection

 (requiredforWi-Fi).

[2]Onlyremovefactoryinstalledjumperfordual

 transformersystems.

[3]Indualtransformersystems,transformer

 commonmustcomefromcoolingtransformer.

[4]Ifneededforsystem.

Provide disconnect and overload protection as required.

2 HEAT / 2 COOL Single or Dual transformer

Set System Type to 22CONV

24VoltACPower(heatingtransformer)[note 2]

24VoltACPower(coolingtransformer)[note 2]

W1 HeatRelayStage1

W2 HeatRelayStage2

Y1 CompressorRelayStage1

Y2 CompressorRelayStage2 [note 4]

G FanRelay

C 24VoltACTransformerCommon[note 1, 3]

Typical Wiring Congurations

NOTE: The “System Type” option will be conﬁgured in the Installer Settings section. The 7300 is a single stage

thermostat and not intended for multi stage equipment.

Conventional Systems

Hydronic Heat Only

Set System Type to 1HD

24VoltACPower(heatingtransformer)[note 2]

W1 ZoneValvePowerOpen

V3 ZoneValvePowerClose

G FanRelay[note 4]

C 24VoltACTransformerCommon[note 1]

Hydronic Heat / 1 Cool

Set System Type to 11HD

24VoltACPower(heatingtransformer)[note 2]

24VoltACPower(coolingtransformer)[note 2]

W1 ZoneValvePowerOpen

V3 ZoneValvePowerClose

Y1 CompressorRelay

G FanRelay

C 24VoltACTransformerCommon[note 1, 3]

Installer Guide 6

1 HEAT / 1 COOL - No Auxiliary Heat

Set System Type to 11HP

Rh 24VoltACPower

Rc ConnectedtoRhwithsuppliedJumperWire

O/B

ChangeoverValve [note 2]

Y1 CompressorRelay

G FanRelay

C 24VoltACTransformerCommon [note 1]

3 HEAT / 2 COOL – Including Auxiliary Heat

Set System Type to 32HP

Rh 24VoltACPower

ConnectedtoRhwithsuppliedJumperWire

O/B ChangeoverValve [note 2]

Compressor1Relay(1ststageheating/cooling)

Compressor2Relay(2ndstageheating/cooling)

AuxiliaryHeatRelay(3rdstageheating)[note 5]

G FanRelay

C 24VoltACTransformerCommon[note 1]

L OptionalSystemFaultMonitor[note 4]

2 HEAT / 1 COOL - Including Auxiliary Heat

Set System Type to 22HP

Rh 24VoltACPower

Rc ConnectedtoRhwithsuppliedJumperWire

O/B

ChangeoverValve[note 2]

Y1 CompressorRelay(1ststageheating/cooling)

AuxiliaryHeatRelay(2ndstageheating)[note 3]

E EmergencyHeatRelay[note 3]

G FanRelay

C 24VoltACTransformerCommon[note 1]

L OptionalSystemFaultMonitor[note 4]

2 HEAT / 2 COOL - No Auxiliary Heat

Set System Type to 32HP

Rh 24VoltACPower

Rc ConnectedtoRhwithsuppliedJumperWire

O/B

ChangeoverValve[note 2]

Compressor1Relay(1ststageheating/cooling)

Compressor2Relay(2ndstageheating/cooling)

G FanRelay

C 24VoltACTransformerCommon[note 1]

L OptionalSystemFaultMonitor[note 4]

NOTES - Heat Pump Systems

[1] Optional24VoltACcommonconnection

(requiredforWi-Fi).

[2]O(coolactive)orB(heatactive)isselectedinthe

 InstallerSettingsmenu.

[3] Installaeldsuppliedjumperbetweenthe

 W2andW1/E/W3terminalsifthereis

 noseparateemergencyheatrelayinstalled.

[4] IftheLterminalisused,the24VoltACcommon

 mustbeconnected(Cterminal).

[5] Ifaseparateemergencyheatrelayisinstalled,the

 W1/E/W3terminalshouldhaveboththeauxiliary

 heat1relayandemergencyheatrelayconnected.

Provide disconnect and overload protection as required.

Typical Wiring Congurations

NOTE: The “System Type” option will be conﬁgured in the Installer Settings section. The 7300 is a single

stage thermostat and not intended for multi stage equipment.

Heat Pump Systems

NOTE: Additional options are conﬁgured in the

Installer Settings section.

A Economizer,FreshAirorOutputControl

K Share-a-Wire

Module[note 2]

NOTES - Additional Wiring Options

[1]Theseterminalscanbeusedtoconnecta

 Braeburn

indoororoutdoorremotesensor.

[2]

Canbeusedtoshareawireonexistinginstallations

 whereacommonconnection(Cwire)isrequired.

Additional Wiring Options - All System Types

IndoororOutdoorRemoteSensor[note 1]

INSTRUCTIONS

DAY/TIME

7 Installer Guide

NOTE: This thermostat ships congured as a 1H/1C conventional

thermostat. Conrm installer settings. See page 10.

W1/E

/AUX1

W2/

AUX2

W3/

O/B

W1/E

/AUX

Attach Thermostat to Sub-Base

3) InsertQuickReferenceCardintoslot

 ontopofthermostat.

1) Lineupthethermostatbodywiththesub-base.

2) Carefullypushthethermostatbodyagainstthe

 sub-baseuntilitsnapsinplace.

Installer Guide 8

Quick Reference

* BACKand NEXTaresecondaryfunctionsofthePROGandHOLDbuttons.Wheninprogrammingor 

  congurationmodes,BACKandNEXTappearinthedisplayscreenindicatingthatthePROGand

HOLDbuttonsnowfunctionasBACKandNEXT.

  **Alsosee#25onpage9.

BACK NEXT

3 4

Room Temperature...................... Displaysthecurrentroomtemperature

Set Temperature..........................Displaysthecurrentsetpointtemperature

Outdoor Temperature Indicator...Displaysalongwiththeoutdoortemperaturereading**

BACK Indicator*........................... BACKbuttonisactive

NEXT Indicator*............................ NEXTbuttonisactive

Service Indicators ...................... Displaysvariousservice/maintenanceinformation

Fan Indicator................................ Indicateswhenthesystemfanisrunning

Wi-Fi Indicator.............................

IndicateswhenconnectedtoWi-Fi(asheswhenconnectionhasbeenlost)

Low Battery Indicator.................. Indicateswhenthebatteriesneedtobereplaced

Hold Mode Indicator ................... IndicatesifthethermostatisinHOLDmode

Lock Mode Indicator ................... Indicatesifthethermostatislocked

System Status Indicator ............. Displaysinformationaboutthestatusofthesystem

Day of the Week........................... Displaysthecurrentdayoftheweek

Program Event Indicator..............Displaystheprogramevent

Time of Day ................................. Displaysthecurrenttimeofday

Thermostat Display

9 Installer Guide

INSTRUCTIONS

DAY/ TIME

BACK NEXT

18 19 20 21

Reset Button ............................... Resetscurrenttime,programandusersettings

SYSTEM Button............................Selectsthesystemyouwanttocontrol

DAY/TIME Button.......................... Setsthecurrenttimeanddayoftheweek

PROG Button................................. Selectsprogrammingmodeorpressfor3secondstoselectSpeedSet

BACK Button*...............................SecondaryfunctionofthePROGbutton-movesbackasetting

HOLD Button.................................Enters/ExitstheHOLDmode(programbypass)

NEXT Button*............................... SecondaryfunctionoftheHOLDbutton-movestonextsetting

RETURN Button............................ Returnstonormalmodefromprogramorsettingmodes

FAN Button................................... Selectsthesystemfanmode

Quick Reference Instructions......Storedinslotlocatedattopofthermostat

SpeedBar

...................................Increasesordecreasessettings(time,temperature,etc.)

Outdoor Temperature................... IfaBraeburn

outdoorsensorwasconnectedyoucanviewtheoutdoor

temperaturebypressingthePROGandHOLDbuttonsatthesametime.

Battery Compartment.................. Locatedinthebackofthermostat

Thermostat

* BACKand NEXTaresecondaryfunctionsofthePROGandHOLDbuttons.Wheninprogrammingor 

  congurationmodes,BACKandNEXTappearinthedisplay,indicatingthatthePROGandHOLDbuttons 

  nowfunctionasBACKandNEXT.

INSTRUCTIONS

DAY/ TIME

TheInstallerSettingsmustbeproperlyconguredinorderforthisthermostattooperatecorrectly.TheInstaller

Settingsaremenudriven.Theportionofthesesettingsthatdonotapplytoyoursetupwillbeskipped.These

settingsareindicatedbelowwithcomments.Moredetailoneachsettingfollowsthistable.

Installer Guide 10

1. PressandholddowntheRETURNand

 buttonsfor3seconds.

2. Releasebothbuttonsandtherstinstaller

 settingwillbedisplayed.

3. Changesettingsasrequiredusingthe

 orportionoftheSpeedBar

4. PressNEXT (HOLD)orBACK (PROG)to

 movetothenextorprevioussetting,

 pressRETURNtoexit.

No. Installer Setting Factory Setting Comments

(Notes follow this table) Default Options (More information follows this table)

1  Residentialor RES RES SelectforResidentialprole

  orCommercialProle    COMM SelectforCommercialprole

2  ProgrammingMode 7 PROG 7 PROG Selectfor7dayprogrammingmode

[note 1] 52 PROG Selectfor5-2dayprogrammingmode

NO PROG Selectfornon-programmablemode

3  ClockFormat 12 HR 12 HR Selectfor12hourclock

24 HR Selectfor24hourclock

4  TemperatureScale F DEG F DEG SelectforFahrenheitdisplay

C DEG SelectforCelsiusdisplay

5  AutoChangeover oF AUTO oF AUTO DisablesAutoChangeovermode

ON AUTO EnablesAutoChangeovermode

11CONV Selectfor1H/1CConventionalsystem

22CONV Selectfor2H/2CConventionalsystem

6  SystemType 11CONV 11HP Selectfor1H/1CHeatPumpsystem

22HP Selectfor2H/2CHeatPumpsystem

32HP Selectfor3H/2CHeatPumpsystem

1HD SelectforHeatOnlyHydronicsystem

11HD SelectforHydronicHeat/1Csystem

7  1stStageDifferential 0.5 DIF1 0.5, 1.0or Selecta1ststagetemperaturedifferentialof.5°,

2.0 DIF1 1°or2°F(.25°,.5°or2°C)

8  2ndStageDifferential 2.0 DIF2 1.0, 2.0, 3.0, Selecta2ndstagetemperaturedifferentialof1°,

[note 2] 4.0, 5.0or 2°,3°,4°,5°or6°F(.5°,1°,1.5°,2°,2.5°or3°C)

6.0 DIF2

9  3rdStageDifferential 2.0 DIF3 1.0, 2.0, 3.0, Selecta3rdstagetemperaturedifferentialof1°,2°,

[note 2] 4.0, 5.0or 3°,4°,5°or6°F(.5°,1°,1.5°,2°,2.5°or3°C)

6.0 DIF3

Installer Settings

NOTE: Shaded areas below do not apply to the 7300.

INSTRUCTIONS

DAY/ TIME

BACK NEXT

11 Installer Guide

No. Installer Setting Factory Setting Comments

(

Notes follow this table) Default Options (More information follows this table)

 10 1stStageFanControl HG FAN 1 HG FAN 1 Selectfor1ststageGasheating

[note 3] HE FAN 1 Selectfor1ststageElectricheating

 11 EmergencyHeat HE EMER HE EMER SelectforElectricEmergencyHeat

  FanControl[note 4] HG EMER SelectforGasEmergencyHeat

 12 ReversingValve REVO REVO SelectforcoolactiveReversingValve(Oterminal)

  (O/BTerminal)[note 5] REVB SelectforheatactiveReversingValve(Bterminal)

 13 FossilFuel AE AUX AE AUX SelectforElectricAuxiliaryheat(withcompressor)

  BackupHeat[note 4] AG AUX SelectforGasAuxiliaryheat(withoutcompressor)

 14

CompressorPowerOutage

oF CPOP oF CPOP DisablesPowerOutageLockoutDelay

  Protection [notes 4, 6] on CPOP EnablesPowerOutageLockoutDelay

 15 ACPowerInterrupt

AC oF MONR

AC oF MONR DisablesACPowerInterruptWarning

  Warning[note 6] AC on MONR EnablesACPowerInterruptWarning

 16 CompressorShort 5 CSCP 5, 4, 3, 2or Selectacompressorshortcycleprotectiondelayof5, 

  CycleProtection[note 7] 0 CSCP  4,3,2or0minutes

 17 ResidualCooling 60 FAN 90, 60, 30  SelectaResidualCoolingFanDelayof90,60,

  FanDelay[note 7]   or0 FAN 30or0seconds.

18 CirculatingFanLock oF CIRC oF CIRC DisablesCirculatingFanLockmode

on CIRC EnablesCirculatingFanLockmode

19 AdaptiveRecovery oF REC oF REC DisablesAdaptive(early)Recoverymode

  Mode(ARM™) [note 8] on REC EnablesAdaptive(early)Recoverymode

 20 IndoorRemoteSensor I SENS I SENS Temperatureissensedfromthermostatonly.

  Control*[note 9] E SENS Temperatureissensedfromremotesensoronly.

A SENS Temperatureiscombinedwiththethermostatand 

        theremotesensor.

 21 LockoutSecurityLevel 2 LOCK 2 LOCK Iflocked–Completelockoutisenabled

1 LOCK Iflocked–Partiallockoutisenabled(SpeedBar

is 

        stillfunctional)

 22 AutoChangeover 3 BAND 2, 3, 4or5 SelectaDeadBandof2°,3°,4°or5˚F  

  DeadBand[note 10] BAND  (1°,2°or3°C)forAutoChangeovermode.

23 CompressorBalance NO BALC NO BALC DisablesBalancePoints

Point[notes 4, 11] 0-50 BALC SelectaCompressorBalancePointof0°-50°F

 (-9°-10°C)

24 AuxiliaryHeatBalance NO BALA NO BALA DisablesBalancePoints

Point[notes 4, 11]

70-40 BALA

SelectaAuxiliaryHeatBalancePointof70°-40°F 

 (21°-4°C)

25 EconomizerFreshAiror OA NONE OA NONE DisablesFreshAirIntakeoption

  OutputControl[note 12] OA ECON EnablesFreshAirIntake(EconomizerMode)

OA TOD EnablesFreshAirIntake(TimeofDayMode)

26

HeatSetPointUpperLimit

90LIM 90-60 LIM

SelectaHeatSetPointUpperLimitof90°-60°F(32°-10°C)

27

CoolSetPointLowerLimit

45LIM 45-80 LIM

SelectaCoolSetPointLowerLimitof45°-80°F(7°-27°C)

[note 7]

 28 InstallerClear CLR0 CLR0 ClearOff-Nochangesmadetosettings

CLR2 Clearsallthermostatsettings(factorydefaults)

*WhenaBraeburn

outdoorsensorisconnected,thethermostatautomaticallyrecognizesit.PressPROGandHOLDatthesame

timetodisplayoutdoortemperature.

NOTE: Additional options such as Service Monitors, setting the lock code, etc. are located in the User Settings –

See User manual for information on setting these options.

Installer Guide 12

NOTES - Installer Settings

1 OnlyavailableifResidentialprolewasselectedinoption1.

2 Onlyavailableifa2or3stagesystemtypewasselectedinoption6.

3 OnlyavailableifaConventionalsystemwasselectedinoption6.

4 Onlyavailableifa2or3stageHeatPumpsystemwasselectedinoption6.

5 OnlyavailableifaHeatPumpsystemwasselectedinoption6.

6 Onlyavailableifthe24VoltACcommonwireisconnectedtotheCterminal.

7 Notavailableifaheatonlyhydronicsystemisselectedinoption6.

8 Onlyavailableifaprogrammableprolewasselectedinoption2.

9 OnlyavailableifaBraeburn®indoorremotesensorwasconnected.

10 Onlyavailableifautochangeoverwasenabledinoption5.

11 OnlyavailableifaBraeburnoutdoorsensorwasconnected.

12 OnlyavailableifaCommercialprolewasselectedinoption1.

Detailed Explanation of Installer Settings (also see NOTES above):

1 Proﬁle–Selectsaresidential(RES)orcommercial(COMM)prole.Ifresidentialisselected,4programming

 eventsperdayareavailable.Ifcommercialisselected,2event,7dayprogrammingisavailable.

2 Programming Mode [note 1]–Selectstheprogrammingmode,eitherfull7dayor5-2day(weekday/

 weekend)programmingornon-programmable.

3 Clock Type–Selectseithera12houror24hourclock.

4 Temperature Scale–Selectsatemperaturescaleofeither°For°C.

5 Auto Changeover–Selectsautochangeoveronoroff.Whenautochangeovermodeisenabledand

 selected,thesystemautomaticallyswitchesbetweenheatingandcoolingmodes.Thereisa5minutedelay

 whenswitchingfromheatingtocoolingorcoolingtoheatinginautochangeovermode.

NOTE: Also see “Auto Changeover Dead Band” in option 21.

6 System Type–Selectsthesystemtypeforyourinstallation.NOTE: Changes made to this option will reset

options 7 through 15 back to their default values dependant on the system type.

7 1st Stage Differential–Selectsa1ststagetemperaturedifferential.

8 2nd Stage Differential [note 2]–Selectsa2ndstagetemperaturedifferential.

9 3rd Stage Differential [note 2]–Selectsa3rdstagetemperaturedifferential.

10 1st Stage Fan Control [note 3]–Selectsa1ststagefancontrolofeithergasorelectricheat.

11 Emergency Heat Fan Control [note 4]–Selectsemergencyheatfancontrolofeithergasorelectricheat.

12 Reversing Valve [note 5]–SelectstheoutputstateoftheO/Bterminal.SelectOforthisterminaltobe

 activeinthecoolmodeorselectBforthisterminaltobeactiveintheheatmode.

13 Auxiliary Fossil Fuel Heat Pump Control [note 4]–Whensettoelectric(AEAUX),boththecompressor

 (1ststage)andauxiliarystage(s)willrunwhenacallforauxiliaryheatismade.Whensettogas(AGAUX),

 thecompressorstage(s)willbelockedoutoneminuteafteracallforauxiliaryheat.NOTE: This option can

be overridden if setting an auxiliary heat balance point in Option 23.

14 Compressor Power Outage Protection [notes 4, 6]–Selectspoweroutageprotectiononoroff.When

 enabled,thisthermostatwillprovidecoldweathercompressorprotectionbylockingoutthecompressor

 stage(s)ofheatingforaperiodoftimeafterapoweroutagegreaterthan60minutes.

15 AC Power Interrupt Warning [note 6]–Whenenabled,thethermostatwilldisplayanoutagewarning

 whenACpowertothethermostatislost.

13 Installer Guide

16 Short Cycle Protection [note 7]–Selectsthenumberofminutesthecoolingcompressorwillbelocked

 outafterturningoff.Thisshortcycleprotectionisalsoactiveintheheatmodeifaheatpumpsystemwas

 selectedinOption6.

17 Residual Cooling Fan Delay [note 7]–

Selectsadelayforthesystemfanafterthecoolingcompressorhas

 turnedoff.Thisdelaywillhelpremovetheremainingcoolairoutoftheductworkprovidingadditionalefciency.

18 Circulating Fan Lock–Whenenabled,theonlyuserfanoptionsavailableareONandCIRC(Circulation).

 TheAUTOoptionisnotavailablewiththisoptionenabled.

19 Adaptive Recovery Mode (early recovery) [note 8]–EnablesordisablestheARM

(adaptiverecovery

 mode)feature.DuringARM,roomtemperatureisrecoveredbyturningontheheatingorcoolingbeforethe

 endofthesetbackperiod.Thesetpointtemperatureischangedtothatoftheupcomingprogramtemperature.

20 Indoor Remote Sensor Control [note 9]–IfaBraeburn

indoorremotesensorisconnectedduring

 installation,thethermostatwillautomaticallydetectthesensor.Whenanindoorsensorisdetected,youmay

 selectbetweenthermostatonly(ISENS),remotesensoronly(ESENS)orcombiningthethermostatandthe

 remotesensor(ASENS).NOTE: This option does not apply to a Braeburn outdoor sensor. When an outdoor

sensor is connected the thermostat automatically recognizes it and no further conﬁguration is necessary.

21 Lockout Security Level–Selectsthelevelofkeypadlockoutwhenthethermostatislocked.Level2locks

theentirethermostat(includingthefrontresetbutton).Level1lockseverythingexcepttheSpeedBar

 allowingforupanddowntemperatureadjustment.NOTE: The lock code is set in the User Settings mode

(see User Manual).

22 Auto Changeover Dead Band [note 10]–Whenautochangeovermodeisenabledinoption5and

 selected,thesystemautomaticallyswitchesbetweenheatingandcoolingwhentheroomtemperature

 meetsthenormalcriteriaforeitheraheatingorcoolingcall.Thereisaforcedseparation(deadband)

 betweentheheatingandcoolingsetpointssothatthesystemsdonotworkagainsteachother.This

 optionselectstheamountofthisdeadbandindegreeswiththedefaultbeing3°F.

23 Compressor Balance Point [notes 4, 11]–Locksouttheuseofthecompressorheatstagewhenthe

 outsideairtemperatureislessthantheselectedsettingof15°Fto50°F(-9°Cto10°C)

24 Auxiliary Heat Balance Point [notes 4, 11]–Locksouttheuseoftheauxiliaryheatstagewhenthe

 outsideairtemperatureexceedstheselectedsettingof70°Fto40°F(21°Cto4°C).NOTE: This balance

point overrides the fossil fuel compressor lockout in option 13. If this option is set to gas and the outdoor

temperature is over the auxiliary balance point, the compressor will remain on during a call for auxiliary heat.

Continued

Installer Guide 14

26 Heat Set Point Upper Limit–Selectstheheatingsetpointupperadjustmentlimit.

27 Cool Set Point Lower Limit [note 7] –Selectsthecoolingsetpointloweradjustmentlimit.

28 Installer Clear–Clearssettingsbasedonyourselection.CLROmakesnochangesandCLR2clearsALL

 thermostatsettingstofactorydefault.

WARNING:IfyoupressNEXTorRETURNafterselectingCLR2theclearwilltakeplaceandtheappropriate

 settingswillbereturnedtofactorydefaults.Ifyoudonotwishtomakeanychanges,usetheSpeedBar

to

 selectCLRO.

Time Step / Override Cooling Call

Occupied YES or NO ON ON OFF

YES ON OFF OFF

NO OFF OFF OFF

Override YES or NO ON ON OFF

External Air or Output Control (A)

Economizer Time of Disabled

Mode Day Mode

Time Step / Override Heating Call

Occupied YES or NO ON ON OFF

YES OFF OFF OFF

NO OFF OFF OFF

Override YES or NO ON ON OFF

External Air Output (A)

Economizer Time of Disabled

Mode Day Mode

Unoccupied

25 Economizer, Fresh Air or Output Control [note 12]–Selectscontroloptions.Selectbetweendisabled

 (NONE),economizermode(ECON)andtimeofday(TOD)mode.

ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigitaldevice,pursuanttoPart15oftheFCCRules.Theselimits

aredesignedtoprovidereasonableprotectionagainstharmfulinterferenceinaresidentialinstallation.Thisequipmentgeneratesusesandcanradiate

radiofrequencyenergyand,ifnotinstalledandusedinaccordancewiththeinstructions,maycauseharmfulinterferencetoradiocommunications.

However,thereisnoguaranteethatinterferencewillnotoccurinaparticularinstallation.Ifthisequipmentdoescauseharmfulinterferencetoradio

ortelevisionreception,whichcanbedeterminedbyturningtheequipmentoffandon,theuserisencouragedtotrytocorrecttheinterferencebyone

ormoreofthefollowingmeasures:

•Reorientorrelocatethereceivingantenna.

•Increasetheseparationbetweentheequipmentandreceiver.

•Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiverisconnected.

•Consultthedealeroranexperiencedradio/TVtechnicianforhelp.

Changesormodicationsnotexpresslyapprovedbythepartyresponsibleforcompliancecouldvoidtheuser’sauthoritytooperatetheequipment.

Thisdevicecomplieswithpart15oftheFCCRules.Operationissubjecttothefollowingtwoconditions:(1)Thisdevicemaynotcauseharmful

inter

ference,and(2)thisdevicemustacceptanyinterferencereceived,includinginterferencethatmaycauseundesiredoperation.

ThisdevicecomplieswithIndustryCanada’slicence-exemptRSSs.Operationissubjecttothefollowingtwoconditions:

(1)Thisdevicemaynotcauseinterference;and

(2)Thisdevicemustacceptanyinterference,includinginterferencethatmaycauseundesiredoperationofthedevice.

CetappareilestconformeauxCNRexemptsdelicenced’IndustrieCanada.Sonfonctionnementestsoumisauxdeuxconditionssuivantes:

(1)Cedispositifnepeutcauserdesinterférences;et

(2)Cedispositifdoitacceptertouteinterférence,ycomprislesinterférencesquipeuventcauserunmauvaisfonctionnementdel’appareil.

MPEG LA License Agreement

THISPRODUCTISLICENSEDUNDERTHEWIRELESSNETWORKPATENTPORTFOLIOLICENSEFORUSEBYACONSUMEROROTHERUSESFORWHICH

THEREISNOREMUNERATION.ANYOTHERUSEOFTHISPRODUCTINANYMANNERISNOTLICENSEDANDISEXPRESSLYPROHIBITEDWITHOUTA

LICENSEUNDERAPPLICABLEPATENTSINTHEWIRELESSNETWORKPATENTPORTFOLIO,WHICHLICENSEISAVAILABLEFROMMPEGLA,LLC,4600S.

ULSTERST.,SUITE400,DENVER,COLORADO80237U.S.A.SEEHTTP://WWW.MPEGLA.COM.

PleaseNote:Thisthermostatmayhavebeenupdatedovertheinternetsincethismanualwasprinted.

Alwaysrefertothesupportwebsiteforthelatestinformation.

15 Installer Guide

Warning

Read Before Testing

• Donotshort(orjumper)acrossterminalsonthegasvalveorattheheatingorcoolingsystemcontrolboard

 totestthethermostatinstallation.Thiscoulddamagethethermostatandvoidthewarranty.

• DonotselecttheCOOLmodeofoperationiftheoutsidetemperatureisbelow50ºF(10ºC).Thiscould

 possiblydamagethecontrolledcoolingsystemandmaycausepersonalinjury.

• Thisthermostatincludesanautomaticcompressorprotectionfeaturetoavoidpotentialdamagetothe

 compressorfromshortcycling.Whentestingthesystem,makesuretotakethisdelayintoaccount.

NOTE: The compressor delay can be bypassed by pressing the reset button on the front of the thermostat.

All user settings will be returned to factory default, however all Installer settings will remain as originally

programmed in section 4.

1 PresstheSYSTEMbuttonuntilthethermostatisinHEATmode.

2 UsingtheSpeedBar®raisethesettemperatureaminimumof3degreesabovethecurrentroom 

 temperature.Thesystemshouldstartwithinafewseconds.Withagasheatingsystem,thefanmay

 notstartrightaway.

3 PressSYSTEMuntilthethermostatisintheOFFmode.Allowtheheatingsystemtofullyshutdown.

4 PressSYSTEMuntilthethermostatisintheCOOLmode.

5 UsingtheSpeedBarlowerthesettemperatureaminimumof3degreesbelowthecurrentroom 

 temperature.Thesystemshouldstartwithinafewseconds(unlesscompressorshortcycleprotection

 isactive–Seenoteabove).

6 PressSYSTEMuntilthethermostatisintheOFFmode.Allowthecoolingsystemtofullyshutdown.

7 PressFANuntilthethermostatisinFANONmode.Thesystemfanshouldstartwithinafewseconds.

8 PressFANuntilthethermostatisinFANAUTOmode.Allowthesystemfantoturnoff.

System Testing

Limited Warranty

Wheninstalledbyaprofessionalcontractor,thisproductisbackedbya5yearlimited

warranty.Limitationsapply.Forlimitations,termsandconditions,youmayobtainafull

copyofthiswarranty:

·Visitusonline:www.braeburnonline.com/warranty

·Phoneus:866.268.5599

·Writeus: BraeburnSystemsLLC

2215CornellAvenue

Montgomery,IL60538

YEAR

WARRANT Y

LIMITED

BraeburnSystemsLLC

2215CornellAvenue•Montgomery,IL60538

TechnicalAssistance:www.braeburnonline.com

Callustoll-free:866-268-5599(U.S.)

630-844-1968(OutsidetheU.S.)

7300-100-02

Store this manual for futur

e reference.

Foradditionalinformationvisit:www.braeburnonline.com

Foronlineaccessvisit:www.bluelinksmartconnect.com

Robertshaw Braeburn 7300 7305 Thermostat User manual

Brand: Robertshaw

Model: Braeburn 7300 7305 Thermostat

Category: Thermostats

Type: User manual

Download PDF

report

Robertshaw Braeburn 7300 7305 Thermostat User manual

Robertshaw Braeburn 7300 7305 Thermostat User manual

Related papers

Other documents