MICRO-EPSILON scanCONTROL 30x0 User manual

Brand: MICRO-EPSILON

Model: scanCONTROL 30x0

Category: Measuring & layout tools

Type: User manual

This manual is also suitable for

scanCONTROL 30xx

Operating Instructions

scanCONTROL 30xx

MICRO-EPSILON

MESSTECHNIK

GmbH & Co. KG

Koenigbacher Str. 15

94496 Ortenburg / Germany

Tel. +49 (0) 8542 / 168-0

Fax +49 (0) 8542 / 168-90

e-mail: [email protected]

www.micro-epsilon.com

Laser scanner

scanCONTROL 30xx

Contents

1. Safety .......................................................................................................................................... 7

1.1 Symbols Used .................................................................................................................................................... 7

1.2 Warnings ............................................................................................................................................................ 7

1.3 Notes on CE Marking ......................................................................................................................................... 8

1.4 Intended Use ...................................................................................................................................................... 9

1.5 Proper Environment ........................................................................................................................................... 9

2. Laser Safety .............................................................................................................................. 10

2.1 General ............................................................................................................................................................. 10

2.2 Laser Class 2M ................................................................................................................................................. 11

2.3 Laser Class 3R ................................................................................................................................................. 12

3. Functional Principle, Technical Data ....................................................................................... 13

3.1 Short Description ............................................................................................................................................. 13

3.1.1 Measuring Principle ........................................................................................................................................ 13

3.1.2 System Setup ................................................................................................................................................... 13

3.1.3 Special Performance Features ......................................................................................................................... 14

3.1.4 Advantages of the Used Sensor Matrix (Difference to Conventional Line Scanners) .................................... 14

3.1.5 Further Features ............................................................................................................................................... 14

3.2 Technical Data .................................................................................................................................................. 15

3.4 LED Displays .................................................................................................................................................... 17

4. Delivery ..................................................................................................................................... 18

4.1 Unpacking, Included in Delivery ...................................................................................................................... 18

4.2 Storage ............................................................................................................................................................. 18

5. Installation and Mounting ........................................................................................................ 19

5.1 Attachment and Mounting .............................................................................................................................. 19

5.2 Connections ..................................................................................................................................................... 24

5.2.1 General ............................................................................................................................................................. 24

5.2.2 Power Supply .................................................................................................................................................. 25

5.2.3 RS422, Synchronization................................................................................................................................... 26

5.2.4 Switching Inputs ............................................................................................................................................... 28

5.2.5 Ethernet Connection ........................................................................................................................................ 30

scanCONTROL 30xx

5.2.6 External Laser Switching (optional) ................................................................................................................. 32

5.3 Installation Instructions .................................................................................................................................... 33

5.4 Getting Ready for Operation, Initial Operation ................................................................................................ 33

6. Operation of the Sensor with a PC .......................................................................................... 34

6.1 Displays ............................................................................................................................................................ 34

6.2 Operating and Demonstration Programs ........................................................................................................ 34

6.3 Installation ........................................................................................................................................................ 35

6.3.1 Requirements ................................................................................................................................................... 35

6.3.2 Connecting scanCONTROL 30xx to the PC ................................................................................................... 35

6.4 Instructions for Operation ................................................................................................................................ 36

6.4.1 Measuring Field Selection ............................................................................................................................... 36

6.4.2 Calibration ........................................................................................................................................................ 38

6.4.3 Operating Modes ............................................................................................................................................. 39

6.4.4 Automatic Exposure Time Regulation ............................................................................................................. 40

6.5 Error Influences ................................................................................................................................................ 41

6.5.1 Reflection of the Target Surface ....................................................................................................................... 41

6.5.2 Color Differences ............................................................................................................................................. 41

6.5.3 Temperature Influences ................................................................................................................................... 41

6.5.4 External Light ................................................................................................................................................... 42

6.5.5 Mechanical Vibrations ...................................................................................................................................... 42

6.5.6 Surface Roughness.......................................................................................................................................... 42

6.5.7 Shadowing Effects ........................................................................................................................................... 43

6.6 Cleaning ........................................................................................................................................................... 44

7. scanCONTROL Output Unit ..................................................................................................... 45

7.1 scanCONTROL Output Unit - Components..................................................................................................... 45

7.2 Connect the Power Supply .............................................................................................................................. 46

7.3 Commissioning scanCONTROL Output Unit .................................................................................................. 47

7.4 Specification of the Components .................................................................................................................... 48

7.4.1 Output Unit Basic ............................................................................................................................................ 48

7.4.2 Supported Modules ......................................................................................................................................... 49

7.4.3 OU-DigitalOut/8-Channel/DC24 V/0.5 A/High-side Switching/8 Actuators ..................................................... 50

7.4.4 OU-AnalogOut/4-Channel/0-10 V .................................................................................................................... 51

8. scanControl Gateway ............................................................................................................... 52

scanCONTROL 30xx

9. Liability for Material Defects .................................................................................................... 53

10. Service, Repair ......................................................................................................................... 53

11. Decommissioning, Disposal .................................................................................................... 53

12. Error Codes .............................................................................................................................. 54

Appendix

A 1 Accessories .............................................................................................................................. 56

A 1.1 Recommended Accessories ............................................................................................................................ 56

A 1.2 Optional Accessories ....................................................................................................................................... 57

scanCONTROL 30xx

Page 7

Safety

scanCONTROL 30xx

1. Safety

The handling of the sensor assumes knowledge of the operating instructions.

1.1 Symbols Used

The following symbols are used in this operating instructions:

Indicates a hazardous situation which, if not avoided, may result in minor or moderate

injury.

Indicates a situation that may result in property damage if not avoided.

Indicates a user action.

Indicates a tip for users.

Measure

Indicates hardware or a software button/menu.

1.2 Warnings

Avoid unnecessary laser radiation to be exposed to the human body.

Switch off the sensor for cleaning and maintenance.

Switch off the sensor for system maintenance and repair if the sensor is integrated into a system.

Caution - use of controls or adjustments or performance of procedures other than those specified may cause

harm.

Connect the power supply and the display/output device according to the safety regulations for electrical

equipment

> Risk of injury

> Damage to or destruction of the sensor

Avoid shocks and impacts to the sensor.

> Damage to or destruction of the sensor

The supply voltage must not exceed the specified limits.

> Damage to or destruction of the sensor

Page 8

Safety

scanCONTROL 30xx

Avoid constant exposure of the sensor to dust or splashes of water by appropriate methods such as blowing

or using a protective housing.

> Damage to or destruction of the sensor

Do not touch the protective windows of the optics. Wipe off any fingerprints immediately with pure alcohol

and a clean cotton cloth with no streaks.

Protect the cables against damage.

> Failure of the measuring device

Do not plug or unplug devices during the operation.

1.3 Notes on CE Marking

The following apply to the scanCONTROL 30xx sensor:

- EU Directive 2014/30/EU,

- EU Directive 2011/65/EU

Products which carry the CE mark satisfy the requirements of the EU directives cited and the relevant

applicable harmonized European standards (EN). The measuring system is designed for use in industrial

environments.

The EU Declaration of Conformity is available to the responsible authorities according to EU Directive,

article 10.

Page 9

Safety

scanCONTROL 30xx

1.4 Intended Use

- The scanCONTROL 30xx sensor is designed for use in industrial applications.

- It is used for

 measuring profile

 measuring length

 monitoring quality and checking dimensions

- The sensor must only be operated within the limits specified in the technical data, see Chap. 3.2.

- The sensor must be used in such a way that no persons are endangered or machines and other material

goods are damaged in the event of malfunction or total failure of the sensor.

- Take additional precautions for safety and damage prevention in case of safety-related applications.

1.5 Proper Environment

- Protection class

 Sensor: IP67 (applies only when connected output connectors or protective caps)

- Temperature range

 Operation: 0 ... +45 °C (+32 ... +113 °F) (with free air circulation)

 Storage: -20 ... +70 °C (-4 ... +158 °F)

- Ambient pressure: Atmospheric pressure

- Humidity: 5 - 95 % (non condensing)

The protection class does not apply for the optical sections during operation as their soiling / contamination

results in adversely affecting or failure of the function.

Only use shielded cables or original cables from the range of accessories for the connection to a power sup-

ply and for the outputs.

Note also the assembly and installation instructions, see Chap. 5.

The IP67 protection class is a specification which is limited to the protection with respect to dust and water.

Oil, steam and emulsion penetration are not included in this protection class and must be tested separately.

Page 10

Laser Safety

scanCONTROL 30xx

2. Laser Safety

2.1 General

The scanCONTROL 30xx sensors operate with a

semiconductor laser having a wavelength of 658 nm

(visible/red) resp. 405 nm (visible/blue).

When operating the scanCONTROL 30xx sensors,

the relevant regulations according to IEC 60825, Part

1 of 05/2014 and the applicable accident prevention

regulations must be followed.

The laser warning labels for Germany have already

been attached. For other non German speaking

countries, an IEC standard label is included in deliv-

ery and the versions valid for the user’s country must

be attached before the device is put into operation for

the first time.

If both warning labels are coverd over when

the unit is installed, the user must ensure that

supplementary labels are applied.

Laser operation is indicated by LED, see Chap. 3.4.

The housing of the optical senors must only be

opened by the manufacturer, see Chap. 9.

For repair and service purposes, the sensors must

always be sent to the manufacturer.

scanCONTROL

LASER RADIATION

DO NOT STARE INTO BEAM

OR EXPOSE USERS OF

TELESCOPE OPTICS

CLASS 2M LASER PRODUCT

IEC 60825-1: 2014

P ≤ 10mW, P ≤ 10mW; E≤ 6mW/cm²;

0 P

λ = 405nm; F = 0...25kHz, t = 7µs...∞

COMPLIES WITH 21 CFR 1040.10 AND 1040.11

EXCEPT FOR CONFORMANCE WITH

IEC 60825-1 ED. 3., AS DESCRIBED IN

LASER NOTICE NO. 56, DATED MAY 8, 2019

LASER

APERTURE

Fig. 1 Sensor with laser labels

Page 11

Laser Safety

scanCONTROL 30xx

Laser radiation.

Close your eyes or im-

mediately turn away if

the laser beam hits the

eye. Irritation or injury

of the eyes possible.

2.2 Laser Class 2M

The sensors fall within laser class 2M. The laser is operated on a pulsed mode, the maximum optical power

is ≤ 10 mW or ≤ 12 mW. The pulse frequency depends on the adjusted measuring rate (0 ... 25 kHz). The

pulse duration can be 7 µs up to infinite.

Observe the laser protection regulations.

Accordingly, the following applies: Laser equipment of the Class 2M can be employed without further

protective measures, when deliberate viewing into the laser beam or into a beam reflected by mirrors is not

longer than 0.25 s. Directly looking into the beam can be dangerous, if the eye-closure reflex is consciously

suppressed, e.g., during adjusting. Directly looking into the beam with optical devices, such as magnifying

glasses, is dangerous. Since generally the presence of the eye-closure reflex should not be assumed, one

should close the eyes or immediately turn away if the laser radiation impinges on the eye.

Laser equipment of the Class 2M can be employed without further protective measures, when deliberate

viewing into the laser beam or into a beam reflected by mirrors is not longer than 0.25 s. Since generally the

presence of the eye-closure reflex should not be assumed, one should close the eyes or immediately turn

away if the laser radiation impinges on the eye.

Lasers of Class 2M are not subject to notification and a laser protection officer is not required.

Attach the following warning labels to the cover (front and rear side) of the housing:

LASER RADIATION

DO NOT STARE INTO BEAM

OR EXPOSE USERS OF

TELESCOPE OPTICS

CLASS 2M LASER PRODUCT

IEC 60825-1: 2014

10 mW, P 10 mW; E 6 mW/cm²;

0 P

λ = 405nm; F = 0...25kHz, t = 7µs...∞

LASER RADIATION

DO NOT STARE INTO BEAM

OR EXPOSE USERS OF

TELESCOPE OPTICS

CLASS 2M LASER PRODUCT

IEC 60825-1: 2014

10 mW, P 10 mW; E 6 mW/cm²;

0 P

λ = 658nm; F = 0...25kHz, t = 7µs...∞

LASER RADIATION

DO NOT STARE INTO BEAM

OR EXPOSE USERS OF

TELESCOPE OPTICS

CLASS 2M LASER PRODUCT

IEC 60825-1: 2014

12 mW, P 12 mW; E 6 mW/cm²;

0 P

λ = 658nm; F = 0...25kHz, t = 7µs...∞

LLT30xx-25/BL, 30xx-50/BL LLT30xx-25, 30xx-50 LLT30xx-200

COMPLIES WITH 21 CFR 1040.10 AND 1040.11

EXCEPT FOR CONFORMANCE WITH

IEC 60825-1 ED. 3., AS DESCRIBED IN

LASER NOTICE NO. 56, DATED MAY 8, 2019

Only for USA

Mark the laser area recognizable and everlasting.

Page 12

Laser Safety

scanCONTROL 30xx

2.3 Laser Class 3R

The sensors with the /3R option fall within laser class 3R. The laser is operated on a pulsed mode, the maxi-

mum optical power is ≤ 30 mW. The pulse frequency depends on the adjusted measuring rate (0 ... 25 kHz).

The pulse duration can be 7 µs up to infinite.

Observe the laser protection regulations.

Accordingly, the following applies: The accessible laser radiation is harmful to the eyes. Looking directly into

the laser beam is harmful to the eyes with laser class 3R devices. Reflections of shiny or mirroring surfaces

are also harmful to the eyes.

Class 3R laser sensors require a laser protection officer.

Attach the following warning labels to the cover (front and rear side) of the sensor housing:

LASER RADIATION

AVOID DIRECT EYE EXPOSURE

CLASS 3R LASER PRODUCT

IEC 60825-1: 2014

P ≤ 30mW, P ≤ 30mW; E ≤ 18mW/cm²;

0 P

λ = 658nm; F = 0...25kHz, t = 7µs...∞

COMPLIES WITH 21 CFR 1040.10 AND 1040.11

EXCEPT FOR CONFORMANCE WITH

IEC 60825-1 ED. 3., AS DESCRIBED IN

LASER NOTICE NO. 56, DATED MAY 8, 2019

LLT30xx-25, LLT30xx-50, LLT30xx-200 Only for USA

In addition, the following information label must be attached to the laser output on the sensor housing:

LASER

APERTURE

Laser radiation. Close

your eyes or immedi-

ately turn away if the

laser beam hits the eye.

Irritation or injury of the

eyes possible.

Page 13

Functional Principle, Technical Data

scanCONTROL 30xx

3. Functional Principle, Technical Data

3.1 Short Description

3.1.1 Measuring Principle

The scanCONTROL 30xx sensor operates ac-

cording to the principle of optical triangulation

(light intersection method):

- A laser line is projected onto the target

surface via a linear optical system.

- The diffusely reflected light from the laser

line is replicated on a sensor matrix by a

high quality optical system and evaluated

in two dimensions.

The laser line triangulation corresponds in

principle to the triangulation of a laser point.

In addition, during the measurement a row

of lines are simultaneously illuminated by the

laser line. Apart from the distance informa-

tion (Z-axis), the exact position of each point

on the laser line (X-axis) is also acquired and

output by the system.

Measuring range

X-axis (profile width)

Measuring

range Z-axis

(profile height)

3.1.2 System Setup

The scanCONTROL 30xx sensor is a compact sensor with an integrated controller. All necessary integral

parts are combined in one housing.

Page 14

Functional Principle, Technical Data

scanCONTROL 30xx

3.1.3 Special Performance Features

- scanCONTROL 30xx features speed and compact design with simultaneously high measurement accu-

racy. A special line-scanning optical system ensures uniform exposure of the measuring field.

- The sensor matrix is arranged in the sensor head according to the Scheimpflug condition which facilitates

uniform image focusing over the whole depth of the measurement range (Z-axis).

- The scanCONTROL 30xx series with integrated profile analysis works even without a PC in conjunction

with saved configurations. The sensor runs the profile measurement internally and calculates default mea-

sured values such as angle or edge position.

Besides measurement value output via Ethernet (Modbus TCP protocol, UDP protocol) and RS422 (Mod-

bus RTU protocol or ASCII format), additional switching signals (results of the determination of limit values)

and analog measurement values can be output. This is done by an optional scanCONTROL Output Unit,

which transforms the determined measurement signals in switching and analog signals for further process-

ing in a PLC.

- scanCONTROL Gateway allows for scanCONTROL SMART sensors to be integrated into various fieldbus

systems (PROFINET, EtherNet/IP, EtherCAT).

3.1.4 Advantages of the Used Sensor Matrix (Difference to Conventional Line Scanners)

- A global shutter (high speed shutter) for the whole profile enables a high profile accuracy for fast applica-

tions without “tilting”.

- The matrix enables the simultaneous exposure and reading of the previous image. Thus the exposure time

is longer at the same profile frequency. With it also dark objects can be measured with a high rate.

- The High Dynamic Range mode (HDR) provides optimal measuring data on difficult target surfaces.

3.1.5 Further Features

- External synchronization and triggering

- Serial interface (RS422) for communication with PLC or PC

- Digital switching inputs, selectable TTL or HTL (selectable Pull-up or Pull down behaviour)

- The automatic control of the exposure time enables consistent measurement results with changing sur-

faces. This function can be switched off on request.

- Ethernet 100/1000 Mbit as fast standard connection to PC

Page 15

Functional Principle, Technical Data

scanCONTROL 30xx

3.2 Technical Data

Model LLT30xx-25 LLT30xx-25/BL LLT30xx-50 LLT30xx-50/BL LLT30xx-200

Z-axis

Measuring range

SMR 77.5 mm 105 mm 200 mm

MMR 85 mm 125 mm 310 mm

EMR 92.5 mm 145 mm 420 mm

HMR 15 mm 40 mm 220 mm

Extended

measuring range

SMR - - 160 mm

EMR - - 460 mm

Linearity

(2 s)

±0.08 % FSO ±0.06 % FSO ±0.08 % FSO ±0.06 % FSO ±0.1 % FSO

Reference resolution

2 3

1.5 µm 3 µm 26 µm

X-axis

Measuring range

SMR 22.9 mm 43,3 mm 130 mm

MMR 25 mm 50 mm 200 mm

EMR 26.8 mm 55,9 mm 270 mm

Extended

measuring range

SMR - - 100 mm

EMR - - 290 mm

Resolution x-axis 2,048 points/profile

Profile

frequency

Standard up to 300 Hz

HIGHSPEED up to 10,000 Hz

Interfaces

Ethernet GigE Vision Output of masurement values; Sensor control; Profile data transmission

Digital inputs Mode switching; Encoder (counter); Trigger

RS422 (half duplex)

Output of masurement values; Sensor control; Trigger; Synchronization

Output of measurement values

Ethernet (UDP datagrams / Modbus TCP); RS422 (ASCII / Modbus RTU)

Analogue

; Switch signal

PROFINET

; EtherCAT

; EtherNet/IP

Page 16

Functional Principle, Technical Data

scanCONTROL 30xx

Model LLT30xx-25 LLT30xx-25/BL LLT30xx-50 LLT30xx-50/BL LLT30xx-200

Display (LED) 1 x Laser ON/OFF, 1 x Data, 1 x Error

Light source (Semiconductor laser) 658 nm (red) 405 nm (blue) 658 nm (red) 405 nm (blue) 658 nm (red)

Aperture angle of laser line 23° 28° 45°

Laser power

Standard (laser class 2M ≤ 10 mW ≤ 12 mW

Option (laser class 3R) ≤ 30 mW - ≤ 30 mW - ≤ 30 mW

Laser switch-off via software, hardware switch-off with /SI option

Permissible

ambient light

(fluorescent light)

10,000 lx

Protection class (sensor) IP67 (when connected)

EMC requirements

according to DIN EN 61000-6-2: 2005, DIN EN61000-6-3: 2007,

DIN EN61326-1:2013 und DIN EN50581:2012

Vibration 2g / 20 … 500 Hz

Shock 15g / 6 ms

Temperature

range

Operation 0 … +45 °C (+32 ... +113 °F)

Storage -20 … +70 °C (-4 ... +158 °F)

Dimensions 96 x 112 x 40 mm

Sensor weight (without cable) 415 g

Supply

11 … 30 VDC, nominal value 24 V, 500 mA,

IEEE 802.3af class 2, Power over Ethernet

FSO = Full Scale Output | SMR = Start of measuring range | MMR = Mid of measuring range |

EMR = End of measuring range | HMR = Height of measuring range

1) Measuring range (standard)

2) Measurement object: Micro-Epsilon standard object

3) According to a one-time averaging across the measuring field (2,048 points)

4) RS422 interface, programmable either as serial interface or as input for triggering/synchronization

5) Only with Output Unit

6) Only with scanCONTROL Gateway

Page 17

Functional Principle, Technical Data

scanCONTROL 30xx

3.4 LED Displays

LED Laser

Meaning

Yellow Laser is on

LED Data

Meaning

Green Measurement is active

Green, flashes slowly Data transmission is active

Green, flashes short Controller accesses

LED Error

Meaning

Red, flashes Error code, see Chap. 12.

Page 18

Delivery

scanCONTROL 30xx

4. Delivery

4.1 Unpacking, Included in Delivery

- 1 scanCONTROL 30xx sensor

- 1 Assembly instructions

- 1 Calibration final inspection

- 2 Protective caps

- 2 Centering elements

- 1 PCR3000-5 multifunction cable, length 5 m; for power supply, trigger and RS422;

screw connector and free cable ends

Carefully remove the components of the measuring system from the packaging and ensure that the

goods are forwarded in such a way that no damage can occur.

Check the delivery for completeness and shipping damage immediately after unpacking.

If there is damage or parts are missing, immediately contact the manufacturer or supplier.

4.2 Storage

Temperature range storage: -20 ... +70 °C (-4 ... +158 °F)

Humidity: 5 - 95 % (non condensing)

Page 19

Installation and Mounting

scanCONTROL 30xx

5. Installation and Mounting

5.1 Attachment and Mounting

- using 2 or 3 screws M5, screwed directly

- using 2 or 3 screws M4, screwed pushed through

Depending on the installation position, it is recommended to define the sensor position using centering ele-

ments and fitting bores.

The cylindrical counterbore ø8H7 is intended for the position-defining centering elements. This allows for the

sensor to be mounted in a reproducible and exchangeable way.

The mounting dimensions refer to the dimensional drawings.

Pay attention to careful handling during mounting and operation.

> Damage to or destruction of the sensor

The laser beam must strike the target surface at right angles. Otherwise, inaccurate measurements cannot be

excluded.

Mount the sensor by means of screws type M5 or by means of through bores for M4.

Bolt connection

Through length Screw Washer Torque

40 mm M4 x ISO 4762-A2 A 4,3 ISO 7089-A2 1.9 Nm

Direct fastening

Screw depth Screw Torque

min 14 mm M5 x ISO 4762-A2 2.5 Nm

Fig. 2 Mounting conditions

The bearing surfaces surrounding the fastening holes (through-holes) are slightly raised.

Mount the sensor only to the existing holes on a flat surface. Clamps of any kind are not permitted. Do not

exceed torques.

> Damage to or destruction of the sensor

> Inaccurate, erroneous measuring values

Page 20

Installation and Mounting

scanCONTROL 30xx

(2)

(1)

(1) Screw M4

(2) Centering element

(2)

(1)

(1) Screw M5

(2) Centering element

Fig. 3 Mounting example with bolt connection Fig. 4 Mounting example with direct fastening

Bolt connection:

- 3 threaded holes (M4)

with centering element:

- additionally 2 cylindrical counter-

bores 8H7 depth 1.8 - 2 mm

100 ±0.2

71.5 ±0.2

3 x

ø4.5

3 x M4

ø8 H7

1.9 ±0.1

Direct fastening:

- 3 bores ø 5.5

with centering element:

- additionally 2 cylindrical counterbores

8H7 depth 1.8 - 2 mm

Fig. 5 Dimensional drawing mounting bores,

dimensions in mm, not to scale

Page is loading ...

MICRO-EPSILON scanCONTROL 30x0 User manual

Brand: MICRO-EPSILON

Model: scanCONTROL 30x0

Category: Measuring & layout tools

Type: User manual

This manual is also suitable for

scanCONTROL 30xx

Download PDF

report

MICRO-EPSILON scanCONTROL 30x0 User manual

This manual is also suitable for

MICRO-EPSILON scanCONTROL 30x0 User manual

Related papers

Other documents