KitchenAid KHPF 7520/I User guide

Brand: KitchenAid

Model: KHPF 7520/I

Category: Hobs

Type: User guide

This manual is also suitable for

KHPS 7520/I

KitchenAid KHPF 7520/I gas hob provides highly efficient burners with different heat outputs to meet your various cooking needs. It features a wok burner with dual flame control, allowing you to cook Asian dishes with authentic flavors. The semi-fast burners offer versatility for everyday cooking tasks, while the auxiliary burner is ideal for simmering or keeping food warm.

Instructions for use

Product description and symbols 4

Using the burners 4

Practical advice on using the hob 5

Positioning the pan supports and wok support 5

Hood and cabinetry clearances (mm) 6

Injector table 6

Warnings and suggestions 7

Safeguarding the environment 8

EC Declaration of conformity 8

Installation (Flush and Semi-Flush fitting) 9

Gas connection 9

Electrical connection 10

Fixing the Hob to the supporting structure.

Traditionally fitted model (Semi Flush fitting). 10

Fixing the Hob to the worktop. Flush fitted model. 11

Adaption to a different type of gas supply 12

Replacing the injectors 12

Fitting the wok burner 13

Regulating the minimum flow level of the gas taps 13

General cleaning & maintenance 14

Care and maintenance of the gas burners 14

Troubleshooting guide 15

After Sales Service 15

1. Removable pan supports

2. 1 kWh auxiliary burner

3. 1.65 kWh semi-fast burner

4. 1.65 kWh semi-fast burner

5. Professional wok burner

6. Auxiliary burner control knob

7. Semi-fast burner control knob

8. Semi-fast burner control knob

9. Professional wok burner control knob

Control Symbols

Off

Maximum flame

Minimum flame

Product description and symbols

To turn on one of the burners:

1. Turn the corresponding control knob

anticlockwise until the indicator coincides with

the maximum flame symbol .

2. Press the control knob to ignite the burner.

3. Once the burner has lit, keep the control knob

pressed for about 5 seconds to allow the safety

thermocouple fitted to each burner to engage.

The thermocouple will switch off the gas supply

to the burner should the flame be accidentally

lost ( A gust of air, momentary interruption of

gas supply or liquid spillage etc).

If the burner does not ignite within about 15

seconds, switch off the burner, check the

fitting of the burner cap and plate for correct

fitting. Wait at least 1 minute before trying

again.

If the burner goes out when the control knob

is released, the thermocouple did not engage.

wait al least 1 minute before repeating strps 1

to 3.

Sometimes, when switching on the WOK’s

burner when cold, the external crown may

take from 2 to 5 seconds to come on. This is a

normal behaviour, due to the time taken for

the gas to reach the crown itself.

Using the burners

Read the instructions to get the best out of your

hob.

• Use pans with a similar diameter to the

burner(see the table).

• Use flat bottomed pans except with the wok

support.

• Do not use excessive water when cooking

foods and use the lid.

• Ensure that pans are fully supported by the pan

supports and do not protrude over the edges.

You should never use:

• two burners simultaneously with just one

container such as a fish kettle.

Burner Ø Pans

wok from 24 to 26 cm

semi fast from 16 to 24 cm

auxiliary from 8 to 14 cm

Practical advice on using the hob

Position the pan supports and wok support as indicated in the figure.

Positioning the pan supports and wok support

Category II2H3+

Electric Power: 230 V - 50 Hz

If a hood is to be installed above the hob, refer to the hood

installation instructions to ensure the correct height above

the hob.

Note: If the distance “A” between the kitchen wall cabinets is

between 600 and 730 mm, height “B" shall be at least 530

mm.

If the distance “A” between the kitchen wall cabinets is wider

than the hob’s width, height “B shall be at least 400 mm.

Hood and cabinetry clearances (mm)

Injector table

Type of gas used Ty p e o f

burner

Injector

label

Control

primary air

(X) (mm)

Nominal

heat flow

Nominal

consumption

Reduced

heat flow

Gas pressure (mbar)

min. nom. max.

NATURAL GAS

(Methane) G20

wok

semi-fast

auxiliary

145

4,20

1,65

1,00

400 l/h

157 l/h

95 l/h

1,40

0,40

0,30

17 20 25

LIQUID

PETROLEUM

GAS (Butane)

G30

wok

semi-fast

auxiliary

100

4,20

1,65

1,00

305 g/h

120 g/h

73 g/h

1,40

0,40

0,30

20 28-30 35

LIQUID

PETROLEUM

GAS (Propane)

G31

wok

semi-fast

auxiliary

100

4,20

1,65

1,00

300 g/h

118 g/h

71 g/h

1,40

0,40

0,30

25 37 45

Type of gas used Configuration model Nominal heat flow kW Overall nominal

consumption

Required air (m

) for

the combustion 1 m

gas

G20 20 mbar 4 burners 8,5 809 l/h 9,52

G30 28-30 mbar 4 burners 8,5 618 g/h 30,94

G31 37 mbar 4 burners 8,5 607 g/h 23,80

To get the most out of your hob, please read

the instructions carefully and keep them for

future consultation.

• These instructions are only valid in the countries

whose destination symbol is shown on the serial

number plate on the hob.

• The packing (plastic bags, expanded

polyurethane, etc) pose a potential threat to

children and should be disposed of carefully.

• Check the appliance has not been damaged

during transportation and remove all

protective packing and films before

installation.

• This hob (cat. 3) was designed to be used

exclusively for cooking food in household

surroundings. Any other use (for example

heating rooms) should be regarded as

improper and dangerous.

• The installation and connection of this

appliance to a gas or electrical supply must

be carried out by a competant, qualified

person in compliance with current

legislation.

• This appliance should be installed in

compliance with standards in force and

only used in well ventilated rooms. Read

the instructions before installing and using

this appliance.

• The pre-fitted gas connector and it's supply

pressure are shown on the label attached

to the bottom of the hob. If this type of gas

supply is not being used, please refer to

the section called Adaption to different

types of gas supply on page 11.

Warnings and suggestions

Packing

The packing material is 100% recyclable and is

labelled with the recycling symbol . Please

dispose of all packing responsibly and carefully.

Product

This appliance is marked according to the

European Directive 2002/96/EC, Waste Electrical

and Electronic Equipment (WEEE).

By ensuring that this product is disposed of

correctly, you will help prevent potentially negative

consequences for the environment and human

health.

The symbol on the product, or on the

documents accompanying this appliance indicates

that this product should not be disposed of as

household waste. Please dispose of this appliance

at an Electrical & Electronic Equipment Collection

point as in accordance with local environmental

regulations for waste disposal. For details of your

local Collection Point please contact your Local

Authority.

Note:

• Incorrect placement of the pan supports can

scratch the hob. To avoid this always ensure

that the rubber feet on the bottom of the pan

supports are the only part of the pan supports

that touch the hob and do not drag the pan

supports across the hob surface.

• Do not use two burners to cook 1 pan.

• In the event of prolonged usage, additional

ventilation may be required (opening a window

or increasing the extraction speed of the hood).

Warning

• This appliance is not intended for use by

persons (including children) with reduced

physical, sensor or mental capabilities or lack of

experience and knowledge unless they have

been given initial supervision or instruction

concerning use of the applaince by a person

responsible for their safety.

• Keep children away from the hob when in

use and don't let them play with the

control knobs or any other part of the

appliance.

• Do not let children play with the pan

supports. The rubber feet on the

underneath of the pan supports could be

swallowed by small and cause serious injury

or suffocation.

• Before replacing the pan supports on the

hob, please check that all the rubber feet

are in place.

• Each time you finish using the hob, always

check that the control knobs are in the off

position and shut off the tap to the gas

mains or cylinder.

• Do not obstruct the air vents at the back

of the appliance in any way.

Safeguarding the environment

EC Declaration of conformity

This appliance has been designed, constructed and marketed in compliance with:

- safety requirements of "GAS" Directive 2009/142/EC (ex-90/396/EEC);

- safety objectives of "Low Voltage" Directive 2006/95/EC (which replaces 73/23/EEC and subsequent

amendments);

- protection requirements of "EMC" Directive 2004/108/EC.

This appliance is suitable for contact with foodstuffs and complies with EC Regulation no. 1935/2004.

Technical information for the installer

• Warning: this is a heavy products which

requires the installation to be carried out

by two people.

• When installing the hob it is advisable to wear

protective gloves.

• This appliance can be installed into a 20mm -

50mm thick worktop.

• If no oven is to be installed below the hob, a

panel must be fitted under the hob to prevent

hob damage and protect the cupboard contents.

This panel must cover the whole of the

underside of the hob and must be positioned so

that an air gap of at least 50mm between the

panel and hob underside is maintained, as a

minimum, and as a maximum 150mm to the

underneath of the work surface.

• This hob is designed to operate perfectly with

any oven in the KitchenAid range. The

Manufacturer declines all responsibility should

any other make of oven be installed. The

manufacturer declines all responsibility

should another make of oven be installed.

Before installation, please ensure that:

• The gas supply (type and pressure) and the

calibration on the hob are compatible (see serial

number plate on the hob and the injector table).

• The cabinetry and appliances surrounding/next

to the hob are heat resistant and in compliance

with local regulations.

• The products of combustion are removed from

the atmosphere in the room by using an

extraction hood or electrical fan installed to the

walls and or windows, in line with current

regulations.

• The air circulates naturally through a suitable

opening that is no less than 100cm

in cross

section, which must be:

- permanent and accessible on the walls of the

room being ventilated and extracting towards

the outside.

- created in such a way that the openings both

inside and out cannot be obstructed, even in

error.

- Protected by plastic grill, metallic netting etc.

that should not reduce the 100cm

cross

section.

- Located in such a position so as not to

interfere with the extraction of the products

of combustion.

Installation (Flush and Semi-Flush fitting)

Connection to the mains gas system must be carried out by a

competant, registered person, in compliance with current

legislation.

• The connection of the hob to the gas mains network or gas

cylinder must be done using a rigid copper or steel pipe with parts

that comply with local standards, or using a flexible stainless steel

pipe with continuous surfaces that comply with local standards.

The flexible metallic pipe should be no longer than 2 linear

metres.

A Gas supply

B Gasket

C Cooktop

Warning: if you use a stainless steel flexible pipe, it must be installed

in such a way that it does not come into contact with moving

cabinetry like drawers or kitchen cupboards and passes at a point

free of obstacles where it can be examined in its entirety.

• After connecting to the gas mains, use soap and water to check

there are no leaks.

Gas connection

The electrical connections must comply with current

legislation and be carried out by a qualified, competent

person.

• Information on the voltage and power absorbed are shown

on the serial no. plate.

• The appliance must be earthed.

• When installing the appliance, we recommend that this hob

is protected by a 3mm bi-polar switch.

• If damaged, the power cable must be replaced with an

identical type of powercable ( H05V2V2-FT90ºC, or

H05RR-F type). We recommend that this operation be

conducted by our After Sales Service. Please contact our

Customer Care Centre on 00800-3810-4026.

• Do not use extension cables.

• The manufacturer declines all responsibility for damage to

persons, pets or goods as a result of failure to comply with

the regulations above.

Electrical connection

Earth

(yellow/green)

Important: The following procedure shall be carried out by

competent technical personnel only. The hob can be installed

on different types of materials, such as masonry, metal, bare

wood and heat resistant laminate coated wood (90°C).

Cut an opening in the worktop to the dimensions shown in the

diagram.

Carefully place the seal on the external outline of the worktop, as

shown in the figure below. Apply a light hand pressure to ensure a

good adhesion to the surface.

Fix the hob to the unit, using the fixing brackets provided.

Note: the electrical power cable must be long enough to allow the

hob to be lifted out from above.

Fixing the Hob to the supporting structure. Traditionally fitted

model (Semi Flush fitting).

Important: The following procedure shall

be carried out by competent technical

personnel only. The hob can be installed

on different types of materials, such as

masonry, metal, bare wood and heat

resistant laminate coated wood (90°C).

Cut an opening into the worktop to the

dimensions shown in the diagram. In order to

correctly fit this type of hob, a 3mm deep

recess around the edge of the opening is also

needed.

Note: In case of laminated worktops with a laminate thickness lower

than 3 mm, create a recess as shown as on the detailed schematic

drawing.

Before positioning the hob, apply the adhesive seal supplied on the

bottom perimeter of the hob itself, where this will be in contact with

the worktop (fig. 2).

Once the seal is in position, place the hob in the recess. Fix the hob

to the worktop using the screws and brackets provided, tightening

them carefully until the hob is perfectly flush. (fig. 3).

Carefully trim the excess seal. In case of installation on wood

(particularly chipboard), any small spaces between the edge of the

recess and the outside edge of the hob should be filled with small

quantities of silicon sealant (see fig. 4). Once the appliance has been

installed, the bottom part of the hob should be completely accessible.

Important:

• tighten the fixing brackets of the hob to the work top by hand,

using minimum force.

• In case of wooden (or similar) worktops, before fitting the

adhesive seal protect the surface of the milled recess with a

primer.

Slots for extra brackets have been created on the bottom of the

appliance, to help achieve a more flush positioning (should this be

necessary). Appropriate brackets can be obtained from the Customer

Care Centre.

Fixing the Hob to the worktop. Flush fitted model.

R.10

Fig. 1

Fig. 2

Fig. 3

Fig. 4

Note: Refer to the injector table to ensure the correct type of

injector is to be fitted.

Traditional burners (T)

1. Remove the pan supports (A).

2. Remove the burners (B).

3. Unscrew the injector (C) with a box spanner 7.

4. Replace the injector with the one for the new gas.

5. Replace burners and pan supports.

Note: Before installing the hob, please remember to stick the gas

calibration label, provided with the replacement injectors over the

gas information on the underside of the hob.

Wok Burner (W)

It is best to change the wok double crown burner before starting

installation. However it is necessary:

1. Lift out the hob from the work surface, removing the installation

fixing pieces.

2. Remove the screws securing the glass, at the back of the hob plate

and those located on both sides of the hob (E).

3. Remove the holding screws that fix the burner to the glass hob.

Once you have removed the glass hob, you can access the wok

burner injector.

4. Remove the injector (F) using a 10mm spanner.

5. Slacken the holding screw (H) to regulate the position (X) of the

gas inlet coupling (G) with regard to the injector.

Replacing the injectors

If you are using a different kind of gas from the one

indicated on the serial no. plate and the orange

label on the back of the hob, you must replace the

injectors; in the case of the Wok burner, adjust the

primary air (see Injector table on page 6).

The orange label should be removed and kept

together with the manual.

Use pressure regulators suitable for the gas

pressures indicated on page 6

• In order to replace the injectors, contact the

Customer Care Centre on 00800-3810-4026,

or a qualified electrician.

• Injectors not supplied as standard should be

requested from the Customer Care Centre on

00800-3810-4026.

• Regulate the minimum levels of the taps.

Note: with liquid petroleum gas ( G30/G31)

the bypass screw must be screwed in fully. If

you then experiance difficulty in turning the

control knob, contact our After sales Service

though our Customer Care Centre on

00800-3810-4026, who will arrange for a

replacement after ascertaining that the tap is

damaged.

Adaption to a different type of gas supply

To fit the double crown wok burner:

Insert in the following order:

1. burner ring (A);

2. decorative covering ring (B);

3. external burner cap (C);

4. internal burner cap (D).

Note: make sure that:

1. the locating pin for the burner ring (A) is inserted correctly in the

slot on the burner unit.

2. that the locating pin on the external

burner cap (C) is inserted in the slot

on the burner ring (A).

Fitting the wok burner

Regulating the minimum flow level must be done with the tap at the

lowest position (small flame) .

There is no need to regulate the primary air in the burners.

To ensure the minimum level is properly regulated, remove the

control knob and adjust the screws found on the tap as follows:

1. tighten to reduce the height of the flame 1 (-)

2. slacken to increase the height of the flame (+);

3. With the burners on, rotate the buttons from the maximum to

the minimum position to check the stability of the flame.

Once you have finished regulating, close up the seals again using

sealing wax.

Regulating the minimum flow level of the gas taps

Always disconnect the hob from the electrical

power supply and wait until it cools before cleaning

and/or doing maintenance work. n order to keep

your hob in good condition, you must keep it

clean, removing any remaining food each time you

use it. Cleaning the hob surface:

• the stainless steel surface may become stained if

it comes into contact with hard water over

along period of time or with extremely strong

cleaning products. Always clean any spillages as

quickly as possible (sauce, coffee, etc..). Wash

with lukewarm water and a mild detergent,

rinse and dry carefully with a soft cloth, or a

cloth designed to clean stainless steel. Only use

stainless steel cleaning products on the stainless

steel trim.

• Do not use harsh or corrosive products,

chloride based products or scourers.

• Do not steam clean.

• Do not use inflammable products.

• Do not leave acidic or alkaline based products

like vinegar, mustard, salt, sugar or lemon juice

lying on the hob, as this will damage the hob

and 'etch' the glass surface.

Note: With time, regular use of the hob could

cause some discolouration around the

burners. This is caused by the high

temperature of the flame and will not affect

the operation or performance of the hob.

General cleaning & maintenance

The pan supports and burners can be removed to

make cleaning easier.

1. Hand wash carefully in hot water with a mild

detergent making sure that all the ingrained dirt

is removed and the openings on the burner are

not blocked. The internal burner cap (D), on

page 12 is made of brass and is subject to a

natural burnishing when it heats up. Clean it

each time you use it with a product specifically

designed for brass. Use hot water and a mild

deteregent to clean the the wok burner

external cap (item (C) on page 12). Never use

harsh products, or scourers that will damage

the special surface coverings.

2. Rinse and dry carefully.

3. Correctly refit the burners and caps in their place.

4. Make sure that when replacing the pan

supports, the pan support is located correctly

for each burner.

Note: Hobs fitted with electronic ignition and

thermocouples must have the ends of the igniters

and thermocouples cleaned regularly and

frequently in order to operate. Please clean them

very carefully with a damp cloth. Any remaining

ingrained food should be removed carefully with a

toothpick, or similar.

To avoid damaging the electronic ignition only

operate with the burners and pan supports

correctly in place.

Care and maintenance of the gas burners

If the hob is not working properly, work through

this guide before contacting our Customer Care

Centre.

The burner does not ignite, or the flame is

unsteady? Check that:

1. the gas, or electricity supply has not been

interrupted and that the control knob is turned

fully on.

2. the gas supply has not run out.

3. the openings on the burner have become

blocked.

4. the end of the electronic igniter is clean.

5. all the parts on the burner are properly

positioned.

The flame doesn’t stay on? Check that:

1. the button was pushed in properly when turning

on the burner for the time required to activate

the safety thermocouple.

2. the burner's openings are not blocked near, or

around the thermocouple.

3. the end part of the thermocouple is clean.

The pans are not stable? Check that:

1. the bottom of the pan is perfectly flat.

2. the pan is centred on the burner.

3. the pan supports are correctly positioned with

all the rubber feet in place.

Troubleshooting guide

Before contacting our Customer Care Centre

please check to see if the problem can be

fixed by refering to the troubleshooting guide.

1. If the fault persists contact us on 00800-3810-

4026. We will ask you for some information, it

will help us, help you if you have the following

information ready to give us:

• a short description of the falut

• the serial number and model number of the

appliance

• the service number ( the number after the

word service on the rating plate on the bottom

of the hob. The service number can also be

found in the warranty booklet.

• your name, full address including postcode and

telephone number.

Note: If there is a problem with your hob,

failure to contact us could seriously

compromise the safety and quality of this

appliance.

After Sales Service

5019 719 01132/C

Printed in Italy

06/10

Whirlpool Europe S.r.l.

Viale G. Borghi, 27 - 21025 Comerio (VA)

Phone 0332.759111 - Fax 0332.759268

www.whirlpool.eu

KitchenAid KHPF 7520/I User guide

Brand: KitchenAid

Model: KHPF 7520/I

Category: Hobs

Type: User guide

This manual is also suitable for

KHPS 7520/I

Download PDF

report

KitchenAid KHPF 7520/I User guide

This manual is also suitable for

KitchenAid KHPF 7520/I User guide

Related papers

Other documents