Sanyo VA-80LAN Installation guide

Category
Security cameras
Type
Installation guide
This option board supports bi-directional communication, allowing you to transfer video and voice data between the camera and PC.
Cautions on Connecting Microphone/Speakers for Bi-directional Voice Communication
Howling may occur if microphone and speakers are put too close. Move them apart or change the speakers orientation to
prevent howling. Also adjust the microphone sensitivity as well as the speaker volume.
For speakers on the camera side, use speakers with built-in amplifier.
System Requirements
The system requirements for camera operation via network are as follows:
•PC: IBM PC/AT and compatibles
•OS: Windows 2000/Windows XP Home Edition/Windows XP Professional
•CPU: Pentium III (800MHz or higher)
Memory: 128MB or more
Network interface: 10Base-T/100Base-TX
Display card: 1024 x 768 pixels or higher, 16 million colors or higher
Web browser: Internet Explorer Ver.6.0 or higher
INSTALLATION MANUAL
Option Board (Network)
About this manual
Please read this installation manual before installing this unit, and always follow the instructions in it for proper use.
VA-80LAN
English Deutsch Français Español
中文简体
L9EBF_WA(VA-80LAN_INSTALLATION).book 1 ページ 2006年12月11日 月曜日 午前10時38分
2
Connection - 1
Connect the camera to the LAN through a switching hub using LAN cables (straight type).
Switching hub PC
Speaker
Microphone
LAN cable (straight type)
Max. 100 m
LAN cable
(straight type)
Voice signal transmission to camera
Voice signal check at PC
Video output
(BNC connector)
Voice output (black)
3.5 φ mini jack
(supplied with the option board)
External microphone input
(white)
3.5 φ mini jack
(supplied with the option board)
Microphone
Speaker
TV monitor
Video/voice data
Max. 100 m
When directly connecting the camera to a PC, use the
LAN cable (cross type).
To prevent electromagnetic interference,
attach the LAN cable to the supplied
clamping core, wrapping it once around the
core.
* Use shielded LAN cables.
L9EBF_WA(VA-80LAN_INSTALLATION).book 2 ページ 2006年12月11日 月曜日 午前10時38分
3
Connection - 1
Internet connection
Connect the camera to a router or ADSL modem with LAN interface
using LAN cables.
About the internet connection
Port forwarding must be set on two of the router ports (camera side).
For details on how to set port forwarding, please refer to your router's
instruction manual.
Video port number
Conduct the following port forwarding settings with respect to the
router:
IP address on the LAN side: Camera IP address (default:
192.168.0.2)
Port number on the LAN side: Camera video port number
(default: 80)
Port number on the WAN side: Optional
For communication, use TCP/IP.
Voice port number
Conduct the following port forwarding settings with respect to the
router:
IP address on the LAN side: Camera IP address (default:
192.168.0.2)
Port number on the LAN side: Camera voice port number
(default: 34341)
Port number on the WAN side: Camera voice port number
(default: 34341)
For communication, use UDP.
When installing multiple cameras on the LAN side, change the voice port
number for the second camera onwards accordingly (default: 34341),
and make the port forwarding setting for the corresponding router.
When connecting to a router, use the straight type LAN cable.
When connecting to an ADSL modem or other devices, refer to the
instruction manual for the device.
Router or
ADSL modem
Internet
To prevent
electromagnetic
interference,
attach the LAN
cable to the
supplied clamping
core, wrapping it
once around the
core.
L9EBF_WA(VA-80LAN_INSTALLATION).book 3 ページ 2006年12月11日 月曜日 午前10時38分
4
1. Installing the Option Board
1
Use the three supplied screws to install the
option board on the power board unit (see the
figure on the left).
2
Pass the LAN cable through the cable hole and
plug it into the LAN port.
Note:
When it is difficult to plug in or pull out the LAN cable, we
recommend that you either use a LAN cable that has no plug cover
at the cable end, or displace the cover if there is one.
3
When using the voice interface, connect the two
supplied cables to the option board.
Connect the red connector cable to the CN893 (red) terminal for
voice output and the white connector cable to the CN892 (white)
terminal for microphone input. These connector cables should be
fixed firmly by wrapping once around the fixer.
4
Configure the network settings (see page 5).
CN893
CN892
1
1
1
2
3
3
L9EBF_WA(VA-80LAN_INSTALLATION).book 4 ページ 2006年12月11日 月曜日 午前10時38分
5
2. Configuring the Network Settings
On the NETWORK SETTING screen, specify the options required for connecting the camera to the network (LAN).
The NETWORK SETTING screen appears only when the camera is equipped with this option board.
For displaying the menu screen, refer to the instruction manual supplied with the camera.
In the following instructions, the lever operations of the system controller (VSP-9000) are shown using xy for vertical operation and vw for horizontal
operation.
1
Use the lever (xy) to select “IP ADDRESS”, use
the lever (vw) to select the IP address assignment
option, and press the [ENTER] button.
2
Use the lever (xy) to select the setting item you
want to change, and press the lever to the right
(vw).
ROnly the selected option is displayed on the screen, and “x
appears below the address.
CAMERA
LENS
PAN/TILT
AUTO MODE
PASSWORD
LANGUAGE
OPTION
ADVANCED MENU
SET
SET
SET
SET
SET
SET
SET
SET
y
y
y
y
y
y
y
y
ENTER
y
y
OPTION
INFORMATION
AUTO FLIP
NETWORK
SET
OFF
SET
ENTER
NETWORK SETTING
IP ADDRESS
PORT
ALARM
MAC ADDRESS
08-00-7I-81-25-J2
FIX
00080
OUT1/2
y
Menu screen
Use the lever (xy) to select “OPTION”.
OPTION screen NETWORK SETTING screen
Use the lever (xy) to select “NETWORK”. Perform the network settings.
FIX : Manual assignment (default: 192.168.0.2)
Go to step
2 (IP ADDRESS SETTING).
AUTO
Automatic assignment (DHCP)
Confirm the information in the screen, and go to step
4.
MEMO: The “MAC ADDRESS” cannot be changed.
NETWORK SETTING
IP ADDRESS
PORT
ALARM
MAC ADDRESS
08-00-7I-81-25-J2
FIX
00080
OUT1/2
y
ENTER
R
IP ADDRESS SETTING
IP ADDRESS
192.168.000.002
SUBNETMASK
255.255.255.000
GATEWAY
192.168.000.001
IP ADDRESS SETTING
IP ADDRESS
192.168.000.002
x
L9EBF_WA(VA-80LAN_INSTALLATION).book 5 ページ 2006年12月11日 月曜日 午前10時38分
6
2. Configuring the Network Settings
3
Select the digit to be changed, and specify the
value.
Use the lever (vw) to move “x” to the digit you want to change,
and use the lever (vw) to select the number.
If you change the setting item, use the lever vw) to move “x” to
either end, and press the lever (vw) toward the same end. This
displays the IP ADDRESS SETTING screen, returning you to
step
2.
4
Use the lever (xy) to select “MENU” – “BACK”,
and press the [ENTER] button.
RReturns to the NETWORK SETTING screen.
5
To change the port number, use the lever (xy) to
select “PORT”, and press the lever to the right (w).
RUse the same procedure as step 3 to change the port number
to your desired value (between 1 and 65535).
6
Use the lever (xy) to select “ALARM” and then
use the lever (vw) to select the alarm output
option.
•OFF: Disables alarm output from the camera to the
network.
•OUT1: Enables alarm output 1 to be sent to the network.
•OUT2: Enables alarm output 2 to be sent to the network.
OUT1/2: Enables alarm outputs 1 and 2 to be sent to the
network (default setting).
7
Use the lever (xy) to select “MENU”, use the
lever (vw) to select “END”, and press [ENTER].
RCloses the settings screen and returns to the normal monitoring
screen.
To return to the previous screen, select “BACK” and press the
[ENTER] button.
IP ADDRESS SETTING
IP ADDRESS
192.168.000.052
x
NETWORK SETTING
IP ADDRESS
PORT
ALARM
MAC ADDRESS
08-00-7I-81-25-J2
FIX
00080
x
OUT1/2
y
NETWORK SETTING
IP ADDRESS
PORT
ALARM
MAC ADDRESS
08-00-7I-81-25-J2
FIX
00090
OUT1/2
y
L9EBF_WA(VA-80LAN_INSTALLATION).book 6 ページ 2006年12月11日 月曜日 午前10時38分
7
2. Configuring the Network Settings
Screen Sequence
IP ADDRESS SETTING
IP ADDRESS
192.168.000.002
SUBNETMASK
255.255.255.000
GATEWAY
192.168.000.001
MENU BACK
NETWORK SETTING
IP ADDRESS
PORT
ALARM
MAC ADDRESS
08-00-7I-81-25-J2
MENU
FIX
00080
OUT1/2
BACK
y
CAMERA
LENS
PAN/TILT
AUTO MODE
PASSWORD
LANGUAGE
OPTION
ADVANCED MENU
PRESET
MENU
SET
SET
SET
SET
SET
SET
SET
SET
OFF
END
y
y
y
y
y
y
y
y
y
y
OPTION
INFORMATION
AUTO FLIP
NETWORK
PRESET
MENU
SET
OFF
SET
OFF
BACK
AUTO
FIX
OFF
OUT1
OUT2
OUT1/2
1-65535
L9EBF_WA(VA-80LAN_INSTALLATION).book 7 ページ 2006年12月11日 月曜日 午前10時38分
8
3. Flow of Camera Operation through to Network Operation
Perform the following procedures according to the detailed instructions given in the INSTRUCTION MANUAL [VA-SW3050LITE] contained in the
supplied CD-ROM.
Refer to
1 Accessing the Camera
Enter your user name and password, and then select a language you want to display on the screen.
User name: admin
Password: admin
6
5
2 Monitoring The Live Video In The Main Screen
8
5
3 Selecting the Operating Conditions
Using the [MAIN SETTINGS] screen for an administrative user, configure the detailed settings for administration.
When you access the camera for the first time, be sure to perform the settings on the [CLOCK SETTINGS] screen.
12
5
4 Changing the Camera Settings
Changes in the camera settings can be made through the network connection.
26
MEMO: After you turn on the power, wait approximately one minute before network connection is established.
If you have to configure TCP/IP settings for your PC, refer to the INSTRUCTION MANUAL from page 4 onward.
L9EBF_WA(VA-80LAN_INSTALLATION).book 8 ページ 2006年12月11日 月曜日 午前10時38分
9
4. Software Setup Procedure for VA-SW3050LITE
The VA-SW3050LITE software achieves multiple monitoring by using up to 128 cameras and allows you to switch the monitoring screen
between single, 4-part split and 16-part split viewing.
Perform the following procedures according to the detailed instructions given in the INSTRUCTION MANUAL [VA-SW3050LITE] contained in the
supplied CD-ROM.
1 Installing the VA-SW3050LITE Software
5
Refer to
2 Starting and Logging in to the VA-SW3050LITE Software
Double-click the “Network Recorder” shortcut icon created on the desktop.
USER ID: admin
PASSWORD: admin
5
5
3 Registering the Cameras with the Software
Register the camera(s) to access, and configure the camera settings such as IP address and camera title.
7
5
4 Viewing the Live Video
11
MEMO: After you turn on the power, wait approximately one minute before you can login.
To view the INSTRUCTION MANUAL contained in the supplied CD-ROM, you need Adobe
®
Reader
®
application. If your PC has not
been installed with it, you can download it for installation from the following web site at Adobe Systems Incorporated.
http://www.adobe.com
L9EBF_WA(VA-80LAN_INSTALLATION).book 9 ページ 2006年12月11日 月曜日 午前10時38分
10
4. Installing the VA-SW3050LITE Software
Start the installation program from the software CD, and use the interactive dialog boxes to advance the installation process.
1
Double-click “Setup.exe” contained in the supplied
CD-ROM.
2
The “Welcome to the InstallShield Wizard for
VA-SW3050LITE” dialog appears.
Click [Next].
3
The “License Agreement” dialog appears.
Select the “I accept the agreement” option and then click [Next].
4
The “Select Destination Location” dialog appears.
Click [Next].
To change the destination folder in which you want to save the
VA-SW3050LITE software, click [Browse] and select the
desired folder. You may also type the folder name directly in the
box.
5
The “Select Start Menu Folder” dialog appears.
Click [Next].
To change the start menu folder, click [Browse] and select the
desired folder. You may also type the folder name directly in the
box.
6
The “Ready to Install” dialog appears.
Click [Install].
Installing
7
The “Completing the VA-SW3050LITE Setup Wizard”
dialog appears.
Click [Finish].
Now you have installed the VA-SW3050LITE software
successfully.
You will find the “Network Recorder” short cut icon on the
desktop.
MEMO:
Microsoft .NET Framework 1.1 is required to use the
VA-SW3050LITE software. If your PC has not been installed
with it, an automatic installation program will show you a
confirmation dialog box to start its setup process, when
you double-click “Setup”. It will be about two minutes
before the installation program finishes.
Once the installation is finished, you may be prompted to
restart the PC. Follow the instructions that may appear on
the screen.
L9EBF_WA(VA-80LAN_INSTALLATION).book 10 ページ 2006年12月11日 月曜日 午前10時38分
11
Specifications
Appearance and specifications are subject to change without prior notice
or obligations.
License for Software Contained in CD-ROM
Please read carefully the terms and conditions contained in the
license agreement that appears on the screen during the software
installation process. Provided that you have agreed to all the terms
and conditions therein, you may use the software subject to the
license agreement.
For information on the other products or services provided by third
parties which are introduced in the CD-ROM, please contact each
supplier or manufacturer.
Copyright notice
This instruction manual is copyrighted by SANYO Electric Co., Ltd.
No materials contained in this manual may be reproduced in any format
without the prior permission of the copyright holder.
Microsoft, Windows and Internet Explorer are registered trademarks or
trademarks of Microsoft Corporation in the United States and other
countries.
The official name for “Windows” used in this manual is Microsoft
®
Windows
®
Operating System. In this manual, note that the word
“Windows” refers to both “Microsoft
®
Windows
®
2000 Operating System”
and “Microsoft
®
Windows
®
XP Operating System”.
Intel and Pentium are registered trademarks or trademarks of Intel
Corporation and its subsidiaries in the United States and other countries.
IBM and IBM PC/AT are trademarks of International Business Machines
Corporation.
Adobe Reader is a trademark of Adobe Systems Incorporated.
UPnP is a trademark of UPnP Implementers Corporation, which is
established by the UPnP Forum SC.
Java is a trademark of Sun Microsystems, Inc.
All other brands and product names in this manual are the registered
trademarks or trademarks of their respective owners.
Power
consumption
16 W (for AC 24 V), 17 W (for AC 230 V)
When installed on the main unit
Power source Supplied from main unit
Weight Approx. 33 g (1.2 oz)
Accessory
Screw ................................................................... 3
Cable with 3.5 φ mini jack
(black and white)......................................... each 1
Clamping core...................................................... 1
CD-ROM (VA-SW3050LITE)................................ 1
L9EBF_WA(VA-80LAN_INSTALLATION).book 11 ページ 2006年12月11日 月曜日 午前10時38分
L9EBF_WA(VA-80LAN_INSTALLATION).book 12 ページ 2006年12月11日 月曜日 午前10時38分
7
2. Konfiguration der Netzwerkeinstellungen
Menüfolge
IP-ADRESSE EINST.
IP-ADRESSE
192.168.000.002
SUBNETZMASKE
255.255.255.000
GATEWAY
192.168.000.001
MENUE ZURUECK
NETZWERK EINST.
IP-ADRESSE
PORT
ALARM
MAC-ADRESSE
08-00-7I-81-25-J2
MENUE
FEST
00080
AL-1/2
ZURUECK
y
KAMERA
OBJEKTIV
PAN/KIPP
AUTO-MODUS
KENNWORT
SPRACHE
OPTION
ERWEIT. MENUE
VOREINST.
MENUE
EINST
EINST
EINST
EINST
EINST
EINST
EINST
EINST
AUS
ENDE
y
y
y
y
y
y
y
y
y
y
OPTION
INFORMATION
AUTOM. UMDREH.
NETZWERK
VOREINST.
MENUE
EINST
AUS
EINST
AUS
ZURUECK
AUTO
FEST
AUS
AL-1
AL-2
AL-1/2
1-65535
L9EBF_WA(VA-80LAN_INSTALLATION).book 7 ページ 2006年12月11日 月曜日 午前10時38分
L9EBF_WA(VA-80LAN_INSTALLATION).book 12 ページ 2006年12月11日 月曜日 午前10時38分
7
2. Configuration des réglages de réseau
Séquence des écrans
REG.ADRESSE IP
ADRESSE IP
192.168.000.002
MASQUE SOUS-RESEAU
255.255.255.000
PASSERELLE
192.168.000.001
MENU RETOUR
REGLAGE RESEAU
ADRESSE IP
PORT
ALARME
ADRESSE MAC
08-00-7I-81-25-J2
MENU
FIX
00080
SOR1/2
RETOUR
y
CAMERA
LENTILLE
PAN/INCL.
MODE AUTO
M/PASSE
LANGUE
OPTION
MENU AVANCE
PREREGLAGE
MENU
REG
REG
REG
REG
REG
REG
REG
REG
ARR
FIN
y
y
y
y
y
y
y
y
y
y
OPTION
INFORMATION
ROTATION AUTO
RESEAU
PREREGLAGE
MENU
REG
ARR
REG
ARR
RETOUR
AUTO
FIX
ARR
SOR1
SOR2
SOR1/2
1-65535
L9EBF_WA(VA-80LAN_INSTALLATION).book 7 ページ 2006年12月11日 月曜日 午前10時38分
L9EBF_WA(VA-80LAN_INSTALLATION).book 12 ページ 2006年12月11日 月曜日 午前10時38分
7
2. Configuración de los ajustes de red
Secuencia de pantalla
AJUS.DIRECC.IP
DIRECCION IP
192.168.000.002
MASCARA SUBRED
255.255.255.000
GATEWAY
192.168.000.001
MENU ATRAS
AJUSTES RED
DIRECCION IP
PUERTO
ALARMA
DIR. MAC
08-00-7I-81-25-J2
MENU
FIJA
00080
OUT1/2
ATRAS
y
CAMARA
LENTE
PAN/INCL.
MODO AUT.
CONTRASENA
IDIOMA
OPCION
MENU AVANZADO
PREAJUSTES
MENU
AJU
AJU
AJU
AJU
AJU
AJU
AJU
AJU
OFF
FIN
y
y
y
y
y
y
y
y
y
y
OPCION
INFORMACION
AUTORROTACION
RED
PREAJUSTES
MENU
AJU
OFF
AJU
OFF
ATRAS
AUTO
FIJA
OFF
OUT1
OUT2
OUT1/2
1-65535
L9EBF_WA(VA-80LAN_INSTALLATION).book 7 ページ 2006年12月11日 月曜日 午前10時38分
L9EBF_WA(VA-80LAN_INSTALLATION).book 12 ページ 2006年12月11日 月曜日 午前10時38分
English Deutsch Français Español
中文简体
此选项板支持双向通信,允许在摄像机和计算机之间传输视频和语音数据
连接麦克风/扬声器进行双向语音通信时请多加小心
将麦克风和扬声器放得过近会出现啸声。将它们挪远些或改变扬声器的方向以避免出现啸声。同时,请调整一下麦克风的灵敏度及扬
声器的音量。
对于摄像机上的扬声器,请使用带有内置放大器的扬声器。
系统要求
通过网络操作摄像机的系统要求如下:
•PC: IBM PC/AT及兼容机
操作系统: Windows 2000/Windows XP Home Edition/Windows XP Professional
•CPU: Pentium III 800MHz或更高)
内存:128MB或以上
网络接口: 10Base-T/100Base-TX
显卡:
1024 x 768
像素或更高,
16 M
色或更高
•Web浏览器:Internet Explorer 6.0或更高版本
安装手册
选项板 (网络)
关于本手册
在安装本装置之前,请仔细阅读本安装手册,并始终遵照本手册中的说明正确使用。
VA-80LAN
L9EBF_WA(VA-80LAN_INSTALLATION).book 1 ページ 2006年12月11日 月曜日 午前10時38分
7
2. 配置网络设定
屏幕顺序
IP ADDRESS SETTING
IP ADDRESS
192.168.000.002
SUBNETMASK
255.255.255.000
GATEWAY
192.168.000.001
MENU BACK
NETWORK SETTING
IP ADDRESS
PORT
ALARM
MAC ADDRESS
08-00-7I-81-25-J2
MENU
FIX
00080
OUT1/2
BACK
y
CAMERA
LENS
PAN/TILT
AUTO MODE
PASSWORD
LANGUAGE
OPTION
ADVANCED MENU
PRESET
MENU
SET
SET
SET
SET
SET
SET
SET
SET
OFF
END
y
y
y
y
y
y
y
y
y
y
OPTION
INFORMATION
AUTO FLIP
NETWORK
PRESET
MENU
SET
OFF
SET
OFF
BACK
AUTO
FIX
OFF
OUT1
OUT2
OUT1/2
1-65535
L9EBF_WA(VA-80LAN_INSTALLATION).book 7 ページ 2006年12月11日 月曜日 午前10時38分
1 / 1

Sanyo VA-80LAN Installation guide

Category
Security cameras
Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Ask the document