Sanyo VA-80LAN Installation guide

This option board supports bi-directional communication, allowing you to transfer video and voice data between the camera and PC.

■ Cautions on Connecting Microphone/Speakers for Bi-directional Voice Communication

● Howling may occur if microphone and speakers are put too close. Move them apart or change the speakers orientation to

prevent howling. Also adjust the microphone sensitivity as well as the speaker volume.

● For speakers on the camera side, use speakers with built-in amplifier.

■ System Requirements

The system requirements for camera operation via network are as follows:

•PC: IBM PC/AT and compatibles

•OS: Windows 2000/Windows XP Home Edition/Windows XP Professional

•CPU: Pentium III (800MHz or higher)

• Memory: 128MB or more

• Network interface: 10Base-T/100Base-TX

• Display card: 1024 x 768 pixels or higher, 16 million colors or higher

• Web browser: Internet Explorer Ver.6.0 or higher

INSTALLATION MANUAL

Option Board (Network)

About this manual

Please read this installation manual before installing this unit, and always follow the instructions in it for proper use.

VA-80LAN

English Deutsch Français Español

中文简体

L9EBF_WA(VA-80LAN_INSTALLATION).book 1 ページ２００６年１２月１１日　月曜日　午前１０時３８分

2

Connection - 1

Connect the camera to the LAN through a switching hub using LAN cables (straight type).

Switching hub PC

Speaker

Microphone

LAN cable (straight type)

Max. 100 m

LAN cable

(straight type)

Voice signal transmission to camera

Voice signal check at PC

Video output

(BNC connector)

Voice output (black)

3.5 φ mini jack

(supplied with the option board)

External microphone input

(white)

3.5 φ mini jack

(supplied with the option board)

Microphone

Speaker

TV monitor

Video/voice data

Max. 100 m

When directly connecting the camera to a PC, use the

LAN cable (cross type).

To prevent electromagnetic interference,

attach the LAN cable to the supplied

clamping core, wrapping it once around the

core.

* Use shielded LAN cables.

L9EBF_WA(VA-80LAN_INSTALLATION).book 2 ページ２００６年１２月１１日　月曜日　午前１０時３８分

3

Connection - 1

■ Internet connection

Connect the camera to a router or ADSL modem with LAN interface

using LAN cables.

■ About the internet connection

Port forwarding must be set on two of the router ports (camera side).

For details on how to set port forwarding, please refer to your router's

instruction manual.

• Video port number

Conduct the following port forwarding settings with respect to the

router:

IP address on the LAN side: Camera IP address (default:

192.168.0.2)

Port number on the LAN side: Camera video port number

(default: 80)

Port number on the WAN side: Optional

For communication, use TCP/IP.

• Voice port number

Conduct the following port forwarding settings with respect to the

router:

IP address on the LAN side: Camera IP address (default:

192.168.0.2)

Port number on the LAN side: Camera voice port number

(default: 34341)

Port number on the WAN side: Camera voice port number

(default: 34341)

For communication, use UDP.

When installing multiple cameras on the LAN side, change the voice port

number for the second camera onwards accordingly (default: 34341),

and make the port forwarding setting for the corresponding router.

When connecting to a router, use the straight type LAN cable.

When connecting to an ADSL modem or other devices, refer to the

instruction manual for the device.

Router or

ADSL modem

Internet

To prevent

electromagnetic

interference,

attach the LAN

cable to the

supplied clamping

core, wrapping it

once around the

core.

L9EBF_WA(VA-80LAN_INSTALLATION).book 3 ページ２００６年１２月１１日　月曜日　午前１０時３８分

4

1. Installing the Option Board

1

Use the three supplied screws to install the

option board on the power board unit (see the

figure on the left).

2

Pass the LAN cable through the cable hole and

plug it into the LAN port.

Note:

When it is difficult to plug in or pull out the LAN cable, we

recommend that you either use a LAN cable that has no plug cover

at the cable end, or displace the cover if there is one.

3

When using the voice interface, connect the two

supplied cables to the option board.

Connect the red connector cable to the CN893 (red) terminal for

voice output and the white connector cable to the CN892 (white)

terminal for microphone input. These connector cables should be

fixed firmly by wrapping once around the fixer.

4

Configure the network settings (see page 5).

CN893

CN892

1

2

3

L9EBF_WA(VA-80LAN_INSTALLATION).book 4 ページ２００６年１２月１１日　月曜日　午前１０時３８分

5

2. Configuring the Network Settings

On the NETWORK SETTING screen, specify the options required for connecting the camera to the network (LAN).

• The NETWORK SETTING screen appears only when the camera is equipped with this option board.

• For displaying the menu screen, refer to the instruction manual supplied with the camera.

• In the following instructions, the lever operations of the system controller (VSP-9000) are shown using xy for vertical operation and vw for horizontal

operation.

1

Use the lever (xy) to select “IP ADDRESS”, use

the lever (vw) to select the IP address assignment

option, and press the [ENTER] button.

2

Use the lever (xy) to select the setting item you

want to change, and press the lever to the right

(vw).

ROnly the selected option is displayed on the screen, and “x”

appears below the address.

CAMERA

LENS

PAN/TILT

AUTO MODE

PASSWORD

LANGUAGE

OPTION

ADVANCED MENU

SET

y

ENTER

y

OPTION

INFORMATION

AUTO FLIP

NETWORK

SET

OFF

SET

ENTER

NETWORK SETTING

IP ADDRESS

PORT

ALARM

MAC ADDRESS

08-00-7I-81-25-J2

FIX

00080

OUT1/2

y

Menu screen

Use the lever (xy) to select “OPTION”.

OPTION screen NETWORK SETTING screen

Use the lever (xy) to select “NETWORK”. Perform the network settings.

FIX : Manual assignment (default: 192.168.0.2)

Go to step

2 (IP ADDRESS SETTING).

AUTO

Automatic assignment (DHCP)

Confirm the information in the screen, and go to step

4.

MEMO: The “MAC ADDRESS” cannot be changed.

NETWORK SETTING

IP ADDRESS

PORT

ALARM

MAC ADDRESS

08-00-7I-81-25-J2

FIX

00080

OUT1/2

y

ENTER

R

IP ADDRESS SETTING

IP ADDRESS

192.168.000.002

SUBNETMASK

255.255.255.000

GATEWAY

192.168.000.001

IP ADDRESS SETTING

IP ADDRESS

192.168.000.002

x

L9EBF_WA(VA-80LAN_INSTALLATION).book 5 ページ２００６年１２月１１日　月曜日　午前１０時３８分

6

2. Configuring the Network Settings

3

Select the digit to be changed, and specify the

value.

• Use the lever (vw) to move “x” to the digit you want to change,

and use the lever (vw) to select the number.

• If you change the setting item, use the lever vw) to move “x” to

either end, and press the lever (vw) toward the same end. This

displays the IP ADDRESS SETTING screen, returning you to

step

2.

4

Use the lever (xy) to select “MENU” – “BACK”,

and press the [ENTER] button.

RReturns to the NETWORK SETTING screen.

5

To change the port number, use the lever (xy) to

select “PORT”, and press the lever to the right (w).

RUse the same procedure as step 3 to change the port number

to your desired value (between 1 and 65535).

6

Use the lever (xy) to select “ALARM” and then

use the lever (vw) to select the alarm output

option.

•OFF: Disables alarm output from the camera to the

network.

•OUT1: Enables alarm output 1 to be sent to the network.

•OUT2: Enables alarm output 2 to be sent to the network.

• OUT1/2: Enables alarm outputs 1 and 2 to be sent to the

network (default setting).

7

Use the lever (xy) to select “MENU”, use the

lever (vw) to select “END”, and press [ENTER].

RCloses the settings screen and returns to the normal monitoring

screen.

• To return to the previous screen, select “BACK” and press the

[ENTER] button.

IP ADDRESS SETTING

IP ADDRESS

192.168.000.052

x

NETWORK SETTING

IP ADDRESS

PORT

ALARM

MAC ADDRESS

08-00-7I-81-25-J2

FIX

00080

x

OUT1/2

y

NETWORK SETTING

IP ADDRESS

PORT

ALARM

MAC ADDRESS

08-00-7I-81-25-J2

FIX

00090

OUT1/2

y

L9EBF_WA(VA-80LAN_INSTALLATION).book 6 ページ２００６年１２月１１日　月曜日　午前１０時３８分

7

2. Configuring the Network Settings

■ Screen Sequence

IP ADDRESS SETTING

IP ADDRESS

192.168.000.002

SUBNETMASK

255.255.255.000

GATEWAY

192.168.000.001

MENU BACK

NETWORK SETTING

IP ADDRESS

PORT

ALARM

MAC ADDRESS

08-00-7I-81-25-J2

MENU

FIX

00080

OUT1/2

BACK

y

CAMERA

LENS

PAN/TILT

AUTO MODE

PASSWORD

LANGUAGE

OPTION

ADVANCED MENU

PRESET

MENU

SET

OFF

END

y

OPTION

INFORMATION

AUTO FLIP

NETWORK

PRESET

MENU

SET

OFF

SET

OFF

BACK

AUTO

FIX

OFF

OUT1

OUT2

OUT1/2

1-65535

L9EBF_WA(VA-80LAN_INSTALLATION).book 7 ページ２００６年１２月１１日　月曜日　午前１０時３８分

8

3. Flow of Camera Operation through to Network Operation

Perform the following procedures according to the detailed instructions given in the INSTRUCTION MANUAL [VA-SW3050LITE] contained in the

supplied CD-ROM.

Refer to

1 Accessing the Camera

Enter your user name and password, and then select a language you want to display on the screen.

User name: admin

Password: admin

6

5

2 Monitoring The Live Video In The Main Screen

8

5

3 Selecting the Operating Conditions

Using the [MAIN SETTINGS] screen for an administrative user, configure the detailed settings for administration.

When you access the camera for the first time, be sure to perform the settings on the [CLOCK SETTINGS] screen.

12

5

4 Changing the Camera Settings

Changes in the camera settings can be made through the network connection.

26

MEMO: • After you turn on the power, wait approximately one minute before network connection is established.

• If you have to configure TCP/IP settings for your PC, refer to the INSTRUCTION MANUAL from page 4 onward.

L9EBF_WA(VA-80LAN_INSTALLATION).book 8 ページ２００６年１２月１１日　月曜日　午前１０時３８分

9

4. Software Setup Procedure for VA-SW3050LITE

The VA-SW3050LITE software achieves multiple monitoring by using up to 128 cameras and allows you to switch the monitoring screen

between single, 4-part split and 16-part split viewing.

Perform the following procedures according to the detailed instructions given in the INSTRUCTION MANUAL [VA-SW3050LITE] contained in the

supplied CD-ROM.

1 Installing the VA-SW3050LITE Software

5

Refer to

2 Starting and Logging in to the VA-SW3050LITE Software

Double-click the “Network Recorder” shortcut icon created on the desktop.

USER ID: admin

PASSWORD: admin

5

3 Registering the Cameras with the Software

Register the camera(s) to access, and configure the camera settings such as IP address and camera title.

7

5

4 Viewing the Live Video

11

MEMO: • After you turn on the power, wait approximately one minute before you can login.

• To view the INSTRUCTION MANUAL contained in the supplied CD-ROM, you need Adobe

®

Reader

®

application. If your PC has not

been installed with it, you can download it for installation from the following web site at Adobe Systems Incorporated.

http://www.adobe.com

L9EBF_WA(VA-80LAN_INSTALLATION).book 9 ページ２００６年１２月１１日　月曜日　午前１０時３８分

10

4. Installing the VA-SW3050LITE Software

Start the installation program from the software CD, and use the interactive dialog boxes to advance the installation process.

1

Double-click “Setup.exe” contained in the supplied

CD-ROM.

2

The “Welcome to the InstallShield Wizard for

VA-SW3050LITE” dialog appears.

Click [Next].

3

The “License Agreement” dialog appears.

Select the “I accept the agreement” option and then click [Next].

4

The “Select Destination Location” dialog appears.

Click [Next].

• To change the destination folder in which you want to save the

VA-SW3050LITE software, click [Browse] and select the

desired folder. You may also type the folder name directly in the

box.

5

The “Select Start Menu Folder” dialog appears.

Click [Next].

• To change the start menu folder, click [Browse] and select the

desired folder. You may also type the folder name directly in the

box.

6

The “Ready to Install” dialog appears.

Click [Install].

☞ Installing

7

The “Completing the VA-SW3050LITE Setup Wizard”

dialog appears.

Click [Finish].

☞ Now you have installed the VA-SW3050LITE software

successfully.

You will find the “Network Recorder” short cut icon on the

desktop.

MEMO:

• Microsoft .NET Framework 1.1 is required to use the

VA-SW3050LITE software. If your PC has not been installed

with it, an automatic installation program will show you a

confirmation dialog box to start its setup process, when

you double-click “Setup”. It will be about two minutes

before the installation program finishes.

• Once the installation is finished, you may be prompted to

restart the PC. Follow the instructions that may appear on

the screen.

L9EBF_WA(VA-80LAN_INSTALLATION).book 10 ページ２００６年１２月１１日　月曜日　午前１０時３８分

11

Specifications

Appearance and specifications are subject to change without prior notice

or obligations.

■ License for Software Contained in CD-ROM

• Please read carefully the terms and conditions contained in the

license agreement that appears on the screen during the software

installation process. Provided that you have agreed to all the terms

and conditions therein, you may use the software subject to the

license agreement.

• For information on the other products or services provided by third

parties which are introduced in the CD-ROM, please contact each

supplier or manufacturer.

■ Copyright notice

This instruction manual is copyrighted by SANYO Electric Co., Ltd.

No materials contained in this manual may be reproduced in any format

without the prior permission of the copyright holder.

Microsoft, Windows and Internet Explorer are registered trademarks or

trademarks of Microsoft Corporation in the United States and other

countries.

The official name for “Windows” used in this manual is Microsoft

®

Windows

®

Operating System. In this manual, note that the word

“Windows” refers to both “Microsoft

®

Windows

®

2000 Operating System”

and “Microsoft

®

Windows

®

XP Operating System”.

Intel and Pentium are registered trademarks or trademarks of Intel

Corporation and its subsidiaries in the United States and other countries.

IBM and IBM PC/AT are trademarks of International Business Machines

Corporation.

Adobe Reader is a trademark of Adobe Systems Incorporated.

UPnP is a trademark of UPnP Implementers Corporation, which is

established by the UPnP Forum SC.

Java is a trademark of Sun Microsystems, Inc.

All other brands and product names in this manual are the registered

trademarks or trademarks of their respective owners.

Power

consumption

16 W (for AC 24 V), 17 W (for AC 230 V)

When installed on the main unit

Power source Supplied from main unit

Weight Approx. 33 g (1.2 oz)

Accessory

Screw ................................................................... 3

Cable with 3.5 φ mini jack

(black and white)......................................... each 1

Clamping core...................................................... 1

CD-ROM (VA-SW3050LITE)................................ 1

L9EBF_WA(VA-80LAN_INSTALLATION).book 11 ページ２００６年１２月１１日　月曜日　午前１０時３８分

L9EBF_WA(VA-80LAN_INSTALLATION).book 12 ページ２００６年１２月１１日　月曜日　午前１０時３８分

Page is loading ...

7

2. Konfiguration der Netzwerkeinstellungen

■ Menüfolge

IP-ADRESSE EINST.

IP-ADRESSE

192.168.000.002

SUBNETZMASKE

255.255.255.000

GATEWAY

192.168.000.001

MENUE ZURUECK

NETZWERK EINST.

IP-ADRESSE

PORT

ALARM

MAC-ADRESSE

08-00-7I-81-25-J2

MENUE

FEST

00080

AL-1/2

ZURUECK

y

KAMERA

OBJEKTIV

PAN/KIPP

AUTO-MODUS

KENNWORT

SPRACHE

OPTION

ERWEIT. MENUE

VOREINST.

MENUE

EINST

AUS

ENDE

y

OPTION

INFORMATION

AUTOM. UMDREH.

NETZWERK

VOREINST.

MENUE

EINST

AUS

EINST

AUS

ZURUECK

AUTO

FEST

AUS

AL-1

AL-2

AL-1/2

1-65535

L9EBF_WA(VA-80LAN_INSTALLATION).book 7 ページ２００６年１２月１１日　月曜日　午前１０時３８分

Page is loading ...

L9EBF_WA(VA-80LAN_INSTALLATION).book 12 ページ２００６年１２月１１日　月曜日　午前１０時３８分

Page is loading ...

7

2. Configuration des réglages de réseau

■ Séquence des écrans

REG.ADRESSE IP

ADRESSE IP

192.168.000.002

MASQUE SOUS-RESEAU

255.255.255.000

PASSERELLE

192.168.000.001

MENU RETOUR

REGLAGE RESEAU

ADRESSE IP

PORT

ALARME

ADRESSE MAC

08-00-7I-81-25-J2

MENU

FIX

00080

SOR1/2

RETOUR

y

CAMERA

LENTILLE

PAN/INCL.

MODE AUTO

M/PASSE

LANGUE

OPTION

MENU AVANCE

PREREGLAGE

MENU

REG

ARR

FIN

y

OPTION

INFORMATION

ROTATION AUTO

RESEAU

PREREGLAGE

MENU

REG

ARR

REG

ARR

RETOUR

AUTO

FIX

ARR

SOR1

SOR2

SOR1/2

1-65535

L9EBF_WA(VA-80LAN_INSTALLATION).book 7 ページ２００６年１２月１１日　月曜日　午前１０時３８分

Page is loading ...

L9EBF_WA(VA-80LAN_INSTALLATION).book 12 ページ２００６年１２月１１日　月曜日　午前１０時３８分

Page is loading ...

7

2. Configuración de los ajustes de red

■ Secuencia de pantalla

AJUS.DIRECC.IP

DIRECCION IP

192.168.000.002

MASCARA SUBRED

255.255.255.000

GATEWAY

192.168.000.001

MENU ATRAS

AJUSTES RED

DIRECCION IP

PUERTO

ALARMA

DIR. MAC

08-00-7I-81-25-J2

MENU

FIJA

00080

OUT1/2

ATRAS

y

CAMARA

LENTE

PAN/INCL.

MODO AUT.

CONTRASENA

IDIOMA

OPCION

MENU AVANZADO

PREAJUSTES

MENU

AJU

OFF

FIN

y

OPCION

INFORMACION

AUTORROTACION

RED

PREAJUSTES

MENU

AJU

OFF

AJU

OFF

ATRAS

AUTO

FIJA

OFF

OUT1

OUT2

OUT1/2

1-65535

L9EBF_WA(VA-80LAN_INSTALLATION).book 7 ページ２００６年１２月１１日　月曜日　午前１０時３８分

Page is loading ...

L9EBF_WA(VA-80LAN_INSTALLATION).book 12 ページ２００６年１２月１１日　月曜日　午前１０時３８分

English Deutsch Français Español

中文简体

此选项板支持双向通信，允许在摄像机和计算机之间传输视频和语音数据。

■ 连接麦克风/扬声器进行双向语音通信时请多加小心

● 将麦克风和扬声器放得过近会出现啸声。将它们挪远些或改变扬声器的方向以避免出现啸声。同时，请调整一下麦克风的灵敏度及扬

声器的音量。

● 对于摄像机上的扬声器，请使用带有内置放大器的扬声器。

■ 系统要求

通过网络操作摄像机的系统要求如下：

•PC: IBM PC/AT及兼容机

• 操作系统: Windows 2000/Windows XP Home Edition/Windows XP Professional

•CPU: Pentium III （800MHz或更高）

• 内存：128MB或以上

• 网络接口： 10Base-T/100Base-TX

• 显卡：

1024 x 768

像素或更高，

16 M

色或更高

•Web浏览器：Internet Explorer 6.0或更高版本

安装手册

选项板（网络）

关于本手册

在安装本装置之前，请仔细阅读本安装手册，并始终遵照本手册中的说明正确使用。

VA-80LAN

L9EBF_WA(VA-80LAN_INSTALLATION).book 1 ページ２００６年１２月１１日　月曜日　午前１０時３８分

Page is loading ...

7

2. 配置网络设定

■ 屏幕顺序

IP ADDRESS SETTING

IP ADDRESS

192.168.000.002

SUBNETMASK

255.255.255.000

GATEWAY

192.168.000.001

MENU BACK

NETWORK SETTING

IP ADDRESS

PORT

ALARM

MAC ADDRESS

08-00-7I-81-25-J2

MENU

FIX

00080

OUT1/2

BACK

y

CAMERA

LENS

PAN/TILT

AUTO MODE

PASSWORD

LANGUAGE

OPTION

ADVANCED MENU

PRESET

MENU

SET

OFF

END

y

OPTION

INFORMATION

AUTO FLIP

NETWORK

PRESET

MENU

SET

OFF

SET

OFF

BACK

AUTO

FIX

OFF

OUT1

OUT2

OUT1/2

1-65535

L9EBF_WA(VA-80LAN_INSTALLATION).book 7 ページ２００６年１２月１１日　月曜日　午前１０時３８分

Page is loading ...

Sanyo VA-80LAN Installation guide

Sanyo VA-80LAN Installation guide

in other languages

Related papers

Other documents