Legrand DS4000 Designer Series Raceway Obstacle Avoidance & Offset Fittings - DS4075, DS4075A Installation guide

Brand: Legrand

Model: DS4000 Designer Series Raceway Obstacle Avoidance & Offset Fittings - DS4075, DS4075A

Type: Installation guide

Legrand DS4000 Designer Series Raceway Obstacle Avoidance & Offset Fittings - DS4075, DS4075A are a versatile solution for overcoming obstacles and creating offsets in your raceway system. With the ability to transition over small conduits, water pipes, and various Wiremold raceway series, the DS4075 Obstacle Avoidance Fitting provides a seamless and professional-looking installation.

The DS4075A Offset Fitting offers even more flexibility, allowing you to create custom offsets in your raceway. With its adjustable design, you can easily trim the base and cover to achieve the desired offset, ensuring a perfect fit for your specific needs.

DS4000 Obstacle Avoidance

& Offset Fittings

INSTALLATION INSTRUCTIONS

Installation Instruction No.: 43266 – January 2006

Wiremold / Legrand Electrical Systems conform to and should be

installed and properly grounded in compliance with requirements

of the current National Electrical Code, Canadian Electrical

Code, or codes administered by local authorities.

All electrical products may represent possible shock or fire

hazard if improperly installed or used. Wiremold electrical

products are UL listed to U.S. and Canadian safety

standards, made for interior use only, and should be installed

in conformance with current local and/or the National

Electrical Code.

DS4075 INSTALLATION: To jump over small Conduits or Raceways:

Products Covered: DS4075, DS4075A

Existing Obstruction

8" [203mm]

Minimum Spacing

12" [305mm]

Maximum Spacing

DS4000B Raceway Base

Step 2. Install Transition Couplings, tighten set screws to secure.

Step 3. Install Internal Shroud on each side.

Step 1. Install DS4000B on either side of the obstacle. The DS4075 Obstacle Avoidance Fitting can transition over 1/2" and 3/4"

trade size conduit, water pipe, Wiremold 500 Series, 700 Series, 2100 Series, 2000 Series, and 2400 Series Raceways.

For more information, visit www.wiremold.com/ds4000.

Step 4. Install DS4000C Raceway Covers. Step 5. Remove appropriate twistout and secure cover. Push on

until it snaps in place

NOTE: To remove Cover or install a Tamper Resistance Kit, refer to page 6 of this instruction sheet.

To use the DS4075 as a transition to Wiremold 500 Series or 700 Series Raceway:

Step 1. Install 500/700 Adapter into the opening with supplied

screws. If using power in both channels, seal off the

other channel with another 500/700 Adapter.

Step 2. Install 500 Series Raceway per instructions.

Step 3. To cross over from the top Channel, remove the

Knockout and install provided Grommet.

Step 4. Install Shroud to isolate Cables as shown.

Step 5. Install DS4000C Cover and DS4075 Fitting Cover to

complete installation.

NOTE: To remove Cover or install a Tamper Resistance Kit, refer to page 6 of this instruction sheet.

To use the DS4075 as a transition to Wiremold 2400 or 2400BD Series Raceway:

Step 1. Install DS4075 as before. Install 2400 Adapter in one

channel for single service. For power and data, use

2400BD Series Raceway.

2400BD Channel Option A: Power from Top Channel.

2400BD Channel Option B: Communications from

Top Channel.

Step 2. Route wiring through knockouts and into 2400 Series

Raceway. Install Covers to complete installation.

NOTE: To remove Cover or install a Tamper Resistance Kit, refer to page 6 of this instruction sheet.

DS4075A OFFSET FITTING INSTALLATION:

Step 1. Measure the offset.

Step 3. Mount to Wall with #8 minimum Fasteners. Tighten

Set Screws as Shown.

Step 2. Trim base of Fitting. Cut on side shown.

3" [76mm] Minimum

Offset

9 1/4" [235mm]

Maximum Offset

Cut

Step 4. Secure to Raceway with Adjust-to-Fit

™

Coupling.

Adjust-to-Fit™

Coupling

Radius Control

Insert

Step 5. Measure Cover distance from top of Divider.

Step 7. Snap on Cover. Step 8. Install Elbow Cover and Inside Corner Trim.

Measure

Step 6. Trim Cover on side as shown.

Cut

NOTE: To remove Cover or install a Tamper Resistance Kit, refer to page 6 of this instruction sheet.

Cover Removal w/650RT

FITTING COVER REMOVAL – Fitting Cover can be removed using two methods:

Cover Removal w/Screwdriver

Step 1. Locate Dimple on Fitting and use as guide to drill

3/16" [5mm] hole for Tamper Resistant Screw.

To make the Fittings fully tamper resistant, use part no. DSTRK.

Step 2. Install Tamper Resistant Screw through drilled hole in the

Cover into the tab with hole on the Fitting Base.

Step 3. Installation complete.

NOTES

Wiremold / Legrand

U.S. and International:

60 Woodlawn Street • West Hartford, CT 06110

1-800-621-0049 • FAX 860-232-2062 • Outside U.S. 860-233-6251

Canada:

570 Applewood Crescent • Vaughan, Ontario L4K 4B4

1-800-723-5175 • FAX 905-738-9721

43266 – January 2006 – For latest specs visit www.wiremold.com

For more information, visit www.wiremold.com/ds4000.

NOTES

Legrand DS4000 Designer Series Raceway Obstacle Avoidance & Offset Fittings - DS4075, DS4075A Installation guide

Brand: Legrand

Model: DS4000 Designer Series Raceway Obstacle Avoidance & Offset Fittings - DS4075, DS4075A

Type: Installation guide

Download PDF

report

Legrand DS4000 Designer Series Raceway Obstacle Avoidance & Offset Fittings - DS4075, DS4075A Installation guide

Legrand DS4000 Designer Series Raceway Obstacle Avoidance & Offset Fittings - DS4075, DS4075A Installation guide

Related papers

Other documents