Legrand 3x4 Enhanced Bi-Directional Video Amplifier Module, IS-0317 Installation guide
- Category
- Video splitters
- Type
- Installation guide
This manual is also suitable for
301 Fulling Mill Road, Suite G
Middletown, PA 17057
Phone (800) 321-2343 / Fax (717) 702-2546
www.onqlegrand.com
Page 1 of 2
©Copyright 2005 by On-Q/Legrand All Rights Reserved.
INSTRUCTION/INSTALLATION SHEET
3x4 Enhanced Bi-Directional Video
Amplifier
IS-0317 REV. O
1. Introduction
The On-Q 3x4 Enhanced Bi-directional Video Amplifier (P/N F7630 as shown below) is designed to distribute
external CATV/Antenna and multiple internal modulated RF signals around the home. Its four high gain
outputs are designed to be used to drive passive splitter modules to provide up to 32 amplified video outputs.
2. Description
The On-Q 3x4 Enhanced Bi-directional Video Amplifier, (see Figure 1) is designed to be mounted in a double
bay bracket with push-pins at each corner of the module.
NOTE: Due to the orientation of the RF connectors and bend radius limitations of coaxial cable, the
3x4 Enhanced Video Amplifier should only be installed in the deeper Titan enclosure, or
Premium/Custom enclosures with enclosure extenders added.
3. Installation
The On-Q 3x4 Enhanced Bi-directional Video Amplifier is typically installed during “trim-out” or as an
upgrade for an existing installation.
CATV input
gain control
Figure 1
RF outputs for
distribution
CATV
input
Aux
inputs
301 Fulling Mill Road, Suite G
Middletown, PA 17057
Phone (800) 321-2343 / Fax (717) 702-2546
www.onqlegrand.com
Page 2 of 2
©Copyright 2005 by On-Q/Legrand All Rights Reserved.
INSTRUCTION/INSTALLATION SHEET
3x4 Enhanced Bi-Directional Video
Amplifier
IS-0317 REV. O
a. Insure that the double bay bracket into which the 3x4 Enhanced Video Amplifier will be installed is housed
in a Titan or Premium/Custom enclosure with enclosure extenders added to provide adequate space for
the required bend radius of the RF cables that will be attached to the module.
b. Align the module on the double space bracket so that the pus-pins on the corner of the module line up
with the holes on the bracket and secure the module with the push-pins.
c. Attach the CATV or antenna input cable to the CATV/ANT jack (see Figure 2).
d. Attach up to two modulated signal cables to the AUXILIARY IN jacks (see Figure 2).
e. Attach RF coaxial jumper cables from the RF OUT jacks to CATV/ANT in jacks of any passive video
modules that will be used for video distribution around the home (see Figure 2).
f. The 3x4 Enhanced Bi-directional Video Amplifier is powered with +12VDC (750mA) from an F7726 Power
Supply. Attach the cable from the power supply to the +12VDC jack on the module, and plug the power
supply into an AC outlet.
g. Use the CATV GAIN adjustment on the front of the module to attenuate the CATV/ANT signal in cases
where that signal is too strong and may cause the high gain outputs to be over driven or to in effect
balance the signal level between internal (fixed gain) and external inputs.
h. Installation of the 3x4 Enhanced Bi-directional Video Amplifier is now complete.
Figure 2
-
1
-
2
Legrand 3x4 Enhanced Bi-Directional Video Amplifier Module, IS-0317 Installation guide
- Category
- Video splitters
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Legrand 36459314 Operating instructions
-
-
-
-
-
-
-
-
-