2. Robertshaw
  3. 41-411 Hot Surface Furnace Ignitor Exact Replacement Rheem 62-22868-82 / 62-22441-01

Robertshaw 41-411 Hot Surface Furnace Ignitor Exact Replacement Rheem 62-22868-82 / 62-22441-01 User manual

  • Hello! I am an AI chatbot trained to assist you with the Robertshaw 41-411 Hot Surface Furnace Ignitor Exact Replacement Rheem 62-22868-82 / 62-22441-01 User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
INSTALLATION DATA
41-411 HOT SURFACE FURNACE
IGNITOR EXACT REPLACEMENT
RHEEM 62-22868-82 / 62-22441-01
The Robertshaw® 41-400 Series Hot Surface lgnitors deliver
dependable ignion in heang systems of every descripon.
from furnaces and boilers to roof top heaters, infrared burners,
unit heaters, water heaters, and many other types of HVAC
equipment.
The 41-411 is specically designed to replace Rheem part
number 62-22868-82, and 62-22441-01.
The 41-400 Series Hot Surface lgnitors are made of high-pu-
rity recrystallized silicon carbide (Crystar™ )which combines
physical and thermal strength with stable electrical properes.
The 41-400 Series are designed to reach ignion temperature(s)
within 17 seconds. They have 18-gauge nickel chrome lead
wires embedded and metalized in place for maximum holding
strength and electrical conducvity. The lead wires are also
enclosed with a special high-temperature ber glass insulaon
providing total electrical protecon.
CAUTION: THIS DEVICE SHOULD BE INSTALLED BY A
QUALIFIED TECH NICIAN WITH DUE REGARD FOR
SAFETY AS IMPROPER IN STALLATION COULD RESULT IN
A HAZARDOUS CONDITION.
Hot surface ignitors get hot! up to 2500°F.
Therefore wait several minutes allowing the
ignitor to cool down, before aempng any
service work. Failure to do so will cause severe
personal injury.
Turn o all gas and electrical power to the
equipment being serviced. Failure to do so can
cause severe injury, death or property damage.
1. Locate model number of the furnace rang plate then nd it
in the chart below.
2. Refer to gure 1 and then 2 or 3 as directed on back page,
when installing new ignitor.
3. Remove old ignitor from furnace. Save all mounng
hardware.
4. To install new ignitor bracket refer to gure 2 or 3 on back
page.
5. Installaon is now complete, put system back in service and
let it run through two or three start-ups to verify proper
operaon.
WARNING
CAUTION
FURNACE MODEL FIGURE NO. FURNACE MODEL FIGURE NO. FURNACE MODEL FIGURE NO.
RHEEM/RUDD HEAT CONTROLLER CENTER ENVIRONMENTAL
SYSTEM
GDA 3 GAD 3 P-UXD 3
GDB 3 GAU 3
GDD 3 GSD 3 WEATHERKING
GDE 2 GSU 3 GDW 3
GEB 3 GYDA 2 GDWE 3
GKA 3 GYUA 2 GDWHC 3
GLA 3 GZD 3 GDWHE 2
GLB 3 GZU 3 GHCA 2
GLD 3 GHID 2
GLE 2 NORDYNE GHST 2
GUH 2 RFYDC 3 GUW 3
GUJ 2 RFYDD 2 GUWE 3
GVC 2 RFYUA 3 GUWHC 3
GWH 2 RFYUC 3 GUWHE 2
GYC 2 RFYUD 2
NOTE: On models GDG, GLG, GVG, WGDAG, WGLAG, WGVAG, use the exisng bracket not the new bracket.
www.Uni-Line.com
www.Robertshaw.com
©2014 Robertshaw
07/14 – 1-867 RevB
INSTALLATION INSTRUCTIONS
Customer Service Telephone 1.800.304.6563
Customer Service Facsimile 1.800.426.0804
[email protected]
Robertshaw®, Ranco®, Paragon® and Uni-Line® are
trademarks of Robertshaw its subsidiaries and/or
affiliated companies. All other brands mentioned
may be the trademarks of their respective owners.
For Technical Service
Telephone 1.800.445.8299
Facsimile 1.630.260.7294
[email protected]
/