Page 1 of 6
Caution : You must read this before you proceed
TABLE
CAUTION: This Table is NOT a TOY.
Keep your child / children at bay during the assembly process.
For moving the Table and to prevent damage to the Table, two adults are needed to execute this
action.
Noble House Home Furnishings LLC
Page 2 of 6
Label Picture Description QTY
A Table Top 1
B Leg 4
C Leg Support 4
Label Picture Description QTY
Bolt (M6x50mm) 9
2 Screw (M6x35mm) 9
3 Washer 9
4 Allen Key 1
Before Beginning Assembly:
1
2
3
4
Noble House Home Furnishings LLC
Page 3 of 6
Step 1
This Table has multiple parts and may require up to some 30 minutes to assemble. To give you an overview
of the Table parts, the above picture is to help you put the various parts into perspective. Please read
through the instructions below to familiarise yourself with the parts and steps before assembly.
OVERVIEW
FRONT FACING
Leg (B)
Table Top (A)
Leg Support (C)
Step 2
Attach Leg(B) to the Table Top(A) using Bolt (
①
) and Washer(
③
) with Allen Key(
④
).
Only loosely tighten the Bolts.
Repeat the same process with the remaining three Legs(B)
Unpack and place all parts on a clean, non-marring surface.
A
B
1
4
3
① ③ ④
Repeat the same process with the remaining three Legs(B)
Noble House Home Furnishings LLC
Page 4 of 6
Step 4
Place Leg Support(C) between Table Top(A) and Leg(B), as shown above
3.1) Secure Leg Support(C) to Table Top(A) using Screw (
②
) with Allen Key(
④
)
3.2) Secure Leg Support(C) to Leg(B) using Screw(②) with Allen Key(④)
Only loosely tighten the Screws.
Repeat the same process with the remaining three Leg Supports(C).
Place the Table right side up on a LEVEL SURFACE to see if it wobbles.
If it wobbles, lift the Table to some 30cm to 50cm height from the ground.
Keep your feet and toes well away from the drop zone.
Drop the Table freely and vertically with the four legs, hitting the ground, at the same time.
This Drop Test will help to ensure that all the Bolts, Screws and gaps all reach full alignment status.
Test again for evenness on a LEVEL SURFACE.
If no wobbles are found, proceed to tighten all the Screws, and Bolts.
CAUTION: When tightening the Screws, and Bolts tighten sequentially. DO NOT tighten any
Bolt, or Screw fully and then move towards the next one. This could cause the frame to warp.
If there are still wobbles, loosen the Screws and Bolts and execute this same drop tests.
If the Table is not stable, it could lead to damage to the product.
Step 3
C
B
A
4
2
Step 3.1
Step 3.2
2
4
If wobble
Test again
30CM~50CM
Noble House Home Furnishings LLC
Page 5 of 6
Step 5
Inspect Table and make sure all parts are adequately connected.
Your Table is ready for use.
This Table can only be used on a flat, level surface.
Noble House Home Furnishings LLC
Page 6 of 6
OUTDOOR
Noble House Home Furnishings LLC
Label Picture Description QTY
A Left Armrest / Leg 1
B Right Armrest / Leg 1
C Seat 1
D Seat Back 1
Caution: You must read this before you proceed
Single Chair
Label Picture Description QTY
E Allen Key 1
F
Bolt
(
M6*30mm
)
5
G
Bolt
(M6*40mm)
3
H
Bolt
(M6*60mm)
3
I Washer 13
J Seat Cushion 1
K
Bolt
(
M6*20mm
)
2
L Connection 1
M Connection 1
Before Beginning Assembly:
Step 1
Step 2
Open the carton and place all the parts on a clean, non-marring surface.
ATTENTION: Occasionally some of the PE Wicker shifts and covers the mounting
positions preventing easy assembly.
The PE wicker should never be cut, but moved away from the mounting positions.
Attach Left Armrest / Leg(A) to the Seat(C) using Bolt(F) and Washer(I) with Allen Key(E)
as shown in the picture above.
Loosely tighten the Bolts.
Attach Seat Back(D) to Seat(C) using Washer(I) , Bolt(G&K) &Connection(L&M) with
Allen Key(E) as pictured above.
Loosely tighten the Bolts.
Step 4
Connect the Chair Legs(A&B) with the Seat Back(D) using Washer(I) and Bolt(H) with
Allen Key(E) as pictured above.
Loosely tighten the Bolts.
Step 3
Attach Right Armrest / Leg(B) to Seat(C) using Bolt(F) and Washer(I) with Allen Key(E ) as
shown in the picture above.
Loosely tighten the Bolts.
Place the Seat Cushion(J) on the Chair.
Your Chair is ready for use.
Step 5
Check for stability and then tighten all Bolts at all joints.
Note: DO NOT fully tighten a Bolt in one go and then move on to the next.
Rather; in a sequential manner, gradually tighten each Bolt until all Bolts are evenly
secured.
This methodology will ensure maximum evenness once all Bolts are fully tightened.
Step 6
/
