LARSON I200363253 Installation guide

LARSON
Brand
LARSON
Model
I200363253
Type
Installation guide

This manual is also suitable for

LARSON I200363253 is a ComfortSEAL Interior Window designed to provide energy efficiency and a custom fit for your home's windows. With its easy installation process, you can enjoy the benefits of a new window in just a few steps. The window is constructed with durable materials and features a top channel cover, corner stops, and a weatherstrip to ensure a snug fit and prevent drafts. Whether you're looking to update the look of your home or simply improve its energy efficiency, the LARSON I200363253 ComfortSEAL Interior Window is a great choice.

LARSON I200363253 is a ComfortSEAL Interior Window designed to provide energy efficiency and a custom fit for your home's windows. With its easy installation process, you can enjoy the benefits of a new window in just a few steps. The window is constructed with durable materials and features a top channel cover, corner stops, and a weatherstrip to ensure a snug fit and prevent drafts. Whether you're looking to update the look of your home or simply improve its energy efficiency, the LARSON I200363253 ComfortSEAL Interior Window is a great choice.

1
Install Top Channel
BISAGRA IZQUIERDA: Instale la manija y la placa receptora
DELE VUELTA PARA LA BISAGRA DERECHA
Parts ListTools Recommended Prep Steps
Install Window
1a
Measure at least 1/4-in from the interior edge of the top jamb exten-
sion and mark with pencil on each side.
1b
Center the top channel in the opening with the front edge aligned on
the marks from 1a. Mark three holes and pre-drill with a 1/8-in drill bit.
1c
Secure the top channel with the three #8x2-in screws provided,
beginning with the side screws and installing the center screw last.
DO NOT OVERTIGHTEN.
1d
To increase energy efficiency, seal both ends of the top channel
with silicone.
ComfortSEAL Interior Windows
INSTALLATION INSTRUCTIONS
202220938-1118
Remove top channel cover
from the top channel.
Leave sash in open
position.
Do not remove
shipping tape.
Two people are
recommended for most
installations due to the
weight of the window.
For additional
infomation on interior
windows and
installation, go to
www.LARSONdoors.com
/windows
Window Styles May Vary
Drill
Phillips Screwdriver Bit
1/8-in Drill Bit
Level
Pencil
Caulk or Silicone
1/4-in
#8x2-in Screw
Actual size
2
Install Corner Stops
3
Complete Installation
2d
Insert the pre-cut weatherstrip sections into the slots on the back
surface of the corner stops.
2e
Draw a second line 1/2” toward the exterior of the line drawn in Step
2b. Line up the front edge of the corner stop with the second pencil line.
Fasten the corner stop in place using the #6x1-in screws, starting with
the bottom screw and then installing the side screw. Repeat for other
corner stop.
Actual size
#6x1-in Screw
TIP: Make sure the
weatherstrip is flush
with the back surface of
the corner stop to
ensure a flat installation.
3a
Using preinstalled hooks, re-hang the window on the top channel. Do
not push the bottom of the window into the opening yet.
3c
Remove tape from window sash and push bottom of the window into place. Test sash operation.
3b
Install channel cover. Starting from one end,
keep pushing until you hear a “click”. Continue
to push along the length of the channel cover
until completely installed.
IMPORTANT: To properly secure the window, the
channel cover must be installed between the channel
and the window opening, NOT within the pocket of
the top channel. Failure to install in the correct position
could result in the unit falling out of the opening.
TOP
BOTTOM
2b
Push bottom of the window unit into the opening. Use
a level to ensure the unit is plumb. Use a pencil to draw
a line near each corner, even with the interior surface of
the window.
2a
Using the preinstalled hooks, hang the window
on the top channel.
TOP
2c
Remove window from opening
to install corner stops.
1/2”
  • Page 1 1
  • Page 2 2

LARSON I200363253 Installation guide

LARSON
Brand
LARSON
Model
I200363253
Type
Installation guide
This manual is also suitable for

LARSON I200363253 is a ComfortSEAL Interior Window designed to provide energy efficiency and a custom fit for your home's windows. With its easy installation process, you can enjoy the benefits of a new window in just a few steps. The window is constructed with durable materials and features a top channel cover, corner stops, and a weatherstrip to ensure a snug fit and prevent drafts. Whether you're looking to update the look of your home or simply improve its energy efficiency, the LARSON I200363253 ComfortSEAL Interior Window is a great choice.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents