Vaisala Multichannel User Interface User manual

IM-EN-MI-C

Instruction Manual

Multichannel User Interface

MI

Document/Revision No. IM-EN-MI/C Eecve: June 5, 2020

PUBLISHED BY

Vaisala Oyj

Vanha Nurmijärvene 21, FI-01670 Vantaa, Finland

P.O. Box 26, FI-00421 Helsinki, Finland

+358 9 8949 1

Visit our Internet pages at www.vaisala.com.

General safety consideraons

Always power o the Mulchannel user interface MI before accessing the modules

behind the display. Vaisala recommends the installaon of an external power switch.

Warning! If this device is used against manufacturer’s instrucons, user safety may be

compromised.

Warranty

For standard warranty terms and condions, see www.vaisala.com/warranty.

Please observe that any such warranty may not be valid in case of damage due to nor-

mal wear and tear, exceponal operang condions, negligent handling or installaon,

or unauthorized modicaons. Please see the applicable supply contract or Condions

of Sale for details of the warranty for each product.

Technical support

Contact Vaisala technical support at helpdesk@vaisala.com. Provide at least the fol-

lowing supporng informaon:

• Product name, model, and serial number

• Name and locaon of the installaon site

• Name and contact informaon of a technical person who can provide further infor-

maon of the problem

For more informaon, see www.vaisala.com/support.

Disposal

When wishing to dispose of an obsolete instrument or any parts of an in-

strument, please observe local and naonal regulaons and requirements

for the disposal of electrical and electronic equipment.

Symbols and terms used in this manual:

This indicates a warning. It provides safety precauon informaon needed to

avoid injury while operang the refractometer system.

This indicates that something is important for the operaon of the refractome-

ter system.

Note. Notes contain addional informaon and hints.

This product manual is delivered to the end user with a Vaisala K-PATENTS® product.

Informaon in this manual is subject to change without noce. When the manual is

changed, a revised copy is published at hp://www.kpatents.com/

Document/Revision No. IM-EN-MI/C Eecve: June 5, 2020

Table of contents

1 Descripon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

2 Mounng . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

3 Connecons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

3.1 Connecng the power cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3.1.1 Power terminals for AC power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3.1.2 Power terminals for DC power . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

3.1.3 External mains switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

3.2 Refractometer cable connecons . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

3.3 Ethernet cable connecon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

3.4 Module cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

3.5 Connecons for external control of Recipe app . . . . . . . . . . . . . . . . 13

4 Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

4.1 Main display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

4.2 Acvang and removing apps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

4.3 Managing users and passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

4.4 System log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

4.5 Ethernet connecons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

4.5.1 MI ethernet connecon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

4.5.2 Refractometer connecon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

4.5.3 Modbus/TCP connecon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

4.5.4 Ethernet/IP connecon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

5 Apps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

5.1 Shared funconality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

5.1.1 Applicaon trend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

5.1.2 Applicaon log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

5.2 Refractometer app . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

5.2.1 Diagnoscs display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

5.2.2 Viewing and adjusng parameters . . . . . . . . . . . . . . . . . . . . . . . . . 37

5.2.3 Refractometer vericaon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

5.2.4 Collecng eld sample points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

5.3 Recipe app . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

5.3.1 Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

5.3.2 Acvang Recipe app . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

5.3.3 Creang a new recipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

5.3.4 Modifying a recipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

5.3.5 Selecng recipe switching mode . . . . . . . . . . . . . . . . . . . . . . . . . . 45

5.3.5.1 Switching recipe manually . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

5.3.5.2 Recipe idencaon numbers for remote control . . . . . . . . . . . 46

5.3.5.3 Switching recipe via General I/O module inputs . . . . . . . . . . . . 47

5.3.5.4 Switching recipe via Modbus/TCP . . . . . . . . . . . . . . . . . . . . . . . 48

5.3.5.5 Switching recipe via Ethernet/IP . . . . . . . . . . . . . . . . . . . . . . . . 48

5.3.6 Using Recipe app to make unit conversions . . . . . . . . . . . . . . . . . 48

5.3.6.1 Creang a recipe for unit conversion . . . . . . . . . . . . . . . . . . . . . 48

5.3.6.2 Displaying several unit conversions simultaneously . . . . . . . . . 49

5.3.7 Conguring mA output for Recipe app . . . . . . . . . . . . . . . . . . . . . 49

6 Module cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

6.1 Installaon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

6.2 Conguraon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

6.3 Relay module card PR-50023 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

6.3.1 Conguring relays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

6.3.2 Nocaon of limit exceeding . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

6.4 mA output module PR-50021 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

6.4.1 Conguring mA outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

6.5 General I/O module PR-50024 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

6.5.1 Connecng inputs/outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

6.5.2 Conguring the general I/O module card . . . . . . . . . . . . . . . . . . . 66

6.5.2.1 Using the general I/O module to trigger prism wash . . . . . . . . 67

7 Prism wash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

7.1 Conguring prism wash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

7.1.1 Wash cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

7.1.2 Seng prism wash parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

8 Specicaons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

8.1 Model code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

8.2 Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

A EU declaraon of conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

B Soware licence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

C Command selecon tree for Refractometer applicaon . . . . . . . . . . . . . . . . 83

D Command selecon tree for sengs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

MI instrucon manual

Document/Revision No. IM-EN-MI/C Eecve: June 5, 2020

1 Descripon 1

1 Descripon

The Mulchannel user interface MI is an industrial computer designed to add funcon-

ality to the PR-43 refractometers. The MI sends and receives data and it can also be

used to control the process.

The Mulchannel user interface MI connects with up to 4 Vaisala K-PATENTS® PR-43

refractometers. With module cards, it can also be used to add external inputs and

outputs (e.g. relays and mA outputs) to your refractometer system.

The MI is operated by the touch-screen display. The stainless steel enclosure gives a

good environmental protecon and allows also outdoor installaons, especially with

the included rain cover. The outer door is easy to open by one hand and the handle

can be modied for padlock to prevent unauthorized access. The module cards can be

reached by opening the inner door. The MI has IP66 rang when the outer door is open

if the inner door (display panel) is xed. With outer door closed the rang is IP67.

Figure 1.1 Mulchannel user interface MI

2 MI instrucon manual

Document/Revision No. IM-EN-MI/C Eecve: June 5, 2020

2 Mounng

The Mulchannel user interface MI can be mounted on a wall with wall mounng or

on a table with a table stand. The mounng locaon should be easily accessible. If

mounted outdoors, the MI has to be protected from rain and direct sunlight.

Display on eye-level

External

mains

switch

100-240VAC4-20 mA

Ethernet

1-4 refractometers

Figure 2.1 Mounng guide

2 Mounng 3

Figure 2.2 Enclosure dimensions

4 MI instrucon manual

Document/Revision No. IM-EN-MI/C Eecve: June 5, 2020

for refractometers

Figure 2.3 Enclosure dimensions

2 Mounng 5

1

1. Bracket screwed to wall by 4 screws.

Screw hole dimensions 325x254mm

325 mm (12.8 inches)

254mm

(10 inches)

1

Figure 2.4 Mounng the wall bracket

1. Four mounting screws

loosely attached

2. Top screws inserted into top bracket verticalmounting slots

3. Lower screws slide into bottom bracket horizontal mounting slots

4. Tighten mounting screws x4

width a 19 mm ring spanner

1

2

3

4

Figure 2.5 Mounng the MI onto the wall bracket

Note: Be careful when mounng, the MI weighs 13 kilos (28.5 lbs).

6 MI instrucon manual

Document/Revision No. IM-EN-MI/C Eecve: June 5, 2020

Important: Do not drill mounng holes in the enclosure as that will aect the protec-

on class of the enclosure and damage the electronics.

The MI is shipped with a rain cover. Vaisala recommends that it is installed even indoors

to protect the top of the door from dust and dirt.

1. Screw out top attaching screws to allow

clearance for rain cover to slot in place

1

2. Retighten screws

2

Figure 2.6 Mounng the rain cover

The table stand is very simple to mount.

Figure 2.7 Table stand

2 Mounng 7

The MI door handle can be modied to make space for a padlock to prevent unautho-

rized access.

Remove handle center cover

and remove segment indicated

by break-line on the back of cover

Replace center cover once

indicated segment has been

removed, making sure the opening

aligns with the channel for the padlock shackle

Figure 2.8 Locking the MI

8 MI instrucon manual

Document/Revision No. IM-EN-MI/C Eecve: June 5, 2020

3 Connecons

Refractometer + MI

max. 200m (656ft)

PR-8441

Ethernet cable for interfaces

M12-4 pin, D-code, M+RS45

Ethernet

PR-8440

Ethernet cable for interfaces

M12-4 pin, D-code, M+M

Ethernet

mA cable

M

M RS45

M

F

PR-8430

Platform 4 cable

M12-8 pin, A-code, F+M

Ethernet, mA, 24V

PR-43 REFRACTOMETER

M-12-8 pin, D code, M

non-Ex

Multi Channel User Interface, MI

1 x M12-4 pin, D-code, F (External Ethernet)

4 x M12-8 pin, A-code, F (System)

max. 90m (295ft)

100-240VAC or 24VDC

Figure 3.1 Mulchannel user interface connecons

3 Connecons 9

3.1 Connecng the power cable

Warning! Make sure there is no power in your cable. Then open the enclosure and

the inner door. You need a TX25 screwdriver to open the inner door retaining screws.

1

2

3

1.Push door gently

2.Lift handle 45 deg up

3.Open the door

Figure 3.2 Opening the enclosure

Remove inner door retaining screws

and open inner door

Figure 3.3 Opening the inner door

Unscrew one of the cable glands and push the power cable through. Connect the power

cable to the power terminals at lower right of the motherboard (see below). Screw on

the cable gland. Close the inner door and turn power on.

3.1.1 Power terminals for AC power

The primary AC power is connected to a separate terminal strip 1/2/3 in the lower right-

hand corner of the motherboard. The three terminals are marked 1.L, 2.N and 3

(protecve earth). The power terminal 3/ is directly connected to the exposed metal

parts of the MI. Wiring to the terminals shall be 1.5mm

2

minimum. The protecve fuse

in the building system shall comply with the local requirements.

10 MI instrucon manual

Document/Revision No. IM-EN-MI/C Eecve: June 5, 2020

1.L 2.N

3

Brown

Blue

Yellow-green

Figure 3.4 AC power terminals on the motherboard

3.1.2 Power terminals for DC power

The DC power is connected to a terminal stripe in the lower right-hand corner of the

motherboard. The three terminals are marked 1+, 2- and 3 (protecve earth). The

power terminal is directly connected to the exposed metal parts of the MI. The 24V

DC power to this terminal stripe shall be supplied from a secondary circuit which is

double or reinforced insulated from the mains supply within the limits for a limited-

energy circuit (maximum 200 VA/U) according to the IEC 61010-1.

3.1.3 External mains switch

External

mains switch

Figure 3.5 Installing external main switch

3 Connecons 11

Important: The MI does not have a built-in power switch. The system is always pow-

ered when connected to a power source. Vaisala recommends mounng an external

mains switch to control the MI’s power supply (Figure 3.5). The external power switch

should be easy to access. It is also recommended to use a 10A/230V circuit breaker for

power supply.

MULTI CHANNEL USER INTERFACE MI

INSTRUMENTS

M12 CONNECTORS

L

N

MAIN POWER

SWITCH PR-10900

L

N

+

-

mA Output 1

4-20mA

POWER SUPPLY

100-240VAC/50-60Hz

4158

-

+

-

+

OPTIONAL 24V POWER

SUPPLY FOR MI

24VDC

ETHERNET

M12-4pin, D-code, M

ETHERNET

M12-4pin, D-code, M

PR-8440 Ethernet cable for interfaces

MI has 8 module slots. Any of module cards

can be installed into any free slot. There could

be multiple module cards in slots depending on

external I/O needs.

PR-50021 mA output module

PR-50023 Relay output module

PR-50021 mA output module

PR-50023 Relay output module

PR-8430

Platform

4 cable

SLOT 2 SLOT 4 SLOT 6 SLOT 8

SLOT 1 SLOT 3 SLOT 5 SLOT 7

1...4 x

L

N

SOLENOID VALVE FOR

PNEUMATICALLY OPERATED

SHUT-OFF VALVE ASSEMBLY:

PR-3340-24/110/240

1...4 x

9

N

L

SAFETY SWITCH

PR-7060

8

7654321

N

L LL

POWER SUPPLY

100-240VAC/50-60Hz

or 24VDC

L

N

1...4 x

Grounding screw

PR-43-...-UN/AX/IA refractometer

(For Intrinsic refractometer see further wiring drawing 4118)

1...4 x

Figure 3.6 Mulchannel user interface wiring

12 MI instrucon manual

Document/Revision No. IM-EN-MI/C Eecve: June 5, 2020

3.2 Refractometer cable connecons

The refractometers are connected to the MI with a M12 male-female 8 pins A-coded

cable PR-8430, maximum length 90 m. The refractometer connectors are located un-

derneath the MI enclosure as a group of four. Refractometer connecons can be made

while the MI is powered. A refractometer can be connected to any of the four connec-

tors.

3.3 Ethernet cable connecon

The lemost connector underneath the MI is for ethernet output. It is for a M12 male

4-pins D-coded cable. The cable can be connected while the MI is powered.

If you wish to connect the MI with e.g. a laptop, you can purchase Interconnecng

cable PR-8330 with a M12-4 pin connector in one end and a RJ-45 connector in the

other end.

3.4 Module cards

For the installaon of the module cards, see Chapter 6 “Module cards”.

Page is loading ...

Vaisala Multichannel User Interface User manual

Related papers

Other documents