Schneider Electric BMENUA0100 User manual

BMENUA0100
Schneider Electric
Brand
Schneider Electric
Model
BMENUA0100
Type
User manual
Internal
How to Install BMENUA0100 Firmware
Using EcoStruxure Automation Device Maintenance
Confidential Property of Schneider Electric
Trinxs
Internal
Non Secure or Standard Mode
Page 2Confidential Property of Schneider Electric |
Internal
•If the card is already configured, take a backup of the
module configuration and reset the module to Factory
Default.
•Once RESET select Standard (Unsecured) Mode and
wait until it is in standard mode (see the LED pattern).
•Use either the default IP address of the control port or
the configured IP address (i.e. 192.164.10.1).
The default is: 10.10.@MAC5.@MAC6.
Example: @MAC 00.80.F4.01.F0.61
Default @IP will be: 10.10.240.97
•If the control port is disabled, use the backplane port IP
address.
•Check communication with the module using Ping.
Page 3Confidential Property of Schneider Electric |
Firmware Updates –Unsecured Mode
Pre-Requisites
Internal
•Open the web page: e.g.
https://192.164.10.1
•Enter the logon and password:
•Logon: installer
•Password: Inst@ller
•Confirm access to the web page of the
module.
•If the password does not open the unit,
repeat the first step and ensure the
module has been reset to factory
default.
•Only the “installer” profile can upgrade
the firmware.
Page 4Confidential Property of Schneider Electric |
Firmware Updates –Unsecured Mode
…Pre-Requisites
Internal
Page 5Confidential Property of Schneider Electric |
Open EcoStruxure Automation Device Maintenance (EADM)
Setup EADM –this step can be bypassed but useful if updating the CPU
Internal
Page 6Confidential Property of Schneider Electric |
Open EcoStruxure Automation Device Maintenance (EADM)
Acquire firmware and load this into the package folder
Modicon M580 BMENUA0100 Firmware SV01.10 | Schneider Electric (se.com)
Internal
Page 7Confidential Property of Schneider Electric |
EcoStruxure Automation Device Maintenance (EADM)
Discover and Manually Add a Device
Internal
Page 8Confidential Property of Schneider Electric |
EcoStruxure Automation Device Maintenance (EADM)
Select the firmware and trust the Connection
Internal
Page 9Confidential Property of Schneider Electric |
EcoStruxure Automation Device Maintenance (EADM)
Enter the Password and Connect
Internal
Page 10Confidential Property of Schneider Electric |
EcoStruxure Automation Device Maintenance (EADM)
Select the device, then update the firmware and confirm the update
Internal
Page 11Confidential Property of Schneider Electric |
EcoStruxure Automation Device Maintenance (EADM)
Monitor the update, verify completion and check the summary
Internal
Secure Mode
Page 12Confidential Property of Schneider Electric |
Internal
•If the card is already configured, take a backup of the
module configuration and reset the module to Factory
Default.
•Once RESET select Secured Mode and wait until it is
in standard mode (see the LED pattern).
•Use either the default IP address of the control port or
the configured IP address (192.164.10.1).
The default is: 10.10.@MAC5.@MAC6.
Example: @MAC 00.80.F4.01.F0.61
Default @IP will be: 10.10.240.97
•If the control port is disabled, use the backplane port IP
address.
Page 13Confidential Property of Schneider Electric |
Firmware Updates –Secured Mode
Pre-Requisites
Internal
•https://192.164.10.1 –(i.e via the
appropriate IPV4 address.
•Logon –first with default setting
•Login: admin
Password : password
•Change to new password as
required –suggestion:
Login: admin
Password : A@dmin_01
•Remove the errors
Page 14Confidential Property of Schneider Electric |
Firmware Updates –Secured Mode
Access Web page
Internal
•Needed to update the firmware
•Under user management, create a New
User.
•Suggestion:
user: Installer
pswd: Inst@ller_01
role: Installer
•Once submitted make sure the
configuration is applied to the device.
Page 15Confidential Property of Schneider Electric |
Firmware Updates –Secured Mode
Configure an installer
Internal
Refer to Firmware Updates –Standard
Mode for more detail
1. Open EADM
2. Make sure the firmware is in the
Data Packages folder
3. Add a manual device
4. Select the BMENUA0100 firmware
5. Trust the certificate
6. Enter the password and connect.
7. Select the device
8. Update firmware
9. Confirm success via the summary
Page 16Confidential Property of Schneider Electric |
Firmware Updates –Secured Mode
Connect using EcoStruxure Automation Device Maintenance (EADM)
Internal
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17

Schneider Electric BMENUA0100 User manual

BMENUA0100
Schneider Electric
Brand
Schneider Electric
Model
BMENUA0100
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers