2. Alarm Controls Corporation
  3. JN-1

Alarm Controls Corporation JN-1 User manual

  • Hello! I am an AI chatbot trained to assist you with the Alarm Controls Corporation JN-1 User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
ALARM CONTROLS CORPORATION
19 BRANDYWINE DRIVE P.O. BOX 280 DEER PARK, NY 11729
WWW.ALARMCONTROLS.COM EMAIL: [email protected]
MODEL JN-1
JACK NUT TOOL KIT
JACKS NUTS PROVIDE A RELIABLE AND SECURE METHOD FOR MOUNTING
MAGNETIC LOCKS IN METAL DOOR FRAMES THAT ARE 3/16” THICK OR LESS.
DURING INSTALLATION THE BODY OF THE JACK-NUT COLLASPES ON THE BACK SIDE
TO FORM LEGS WHICH GRIP THE INSIDE OF THE MOUNTING SURFACE.
THE JN-1 JACK NUT TOOL KIT CONTAINS
ONE - JACK NUT INSTALLATION TOOL
ONE - 25/64” DRILL BIT
ONE - 5M MANDREL INSTALLED IN INSTALLATION TOOL
FIFTY - 5M JACK NUTS
FIFTY - 5M x .75” FLAT HEAD PHILLIPS MACHINE SCREWS
ONE EACH OF 3M, 4M & 6M MANDREL
METAL TOOL BOX HOLDS ALL ITEMS
MODEL JN-1
JACK NUT INSTALLATION TOOL
ALARM CONTROLS CORPORATION
“QUALITY SECURITY EQUIPMENT SINCE 1971”
19 BRANDYWINE DRIVE P.O. BOX 280
DEER PARK, NY 11729
PH: 800 645-5538 FAX: 631 586-4220
EMAIL: [email protected]
WWW.ALARMCONTROLS.COM
ALARM CONTROLS CORPORATION
“QUALITY SECURITY EQUIPMENT SINCE 1971”
19 BRANDYWINE DRIVE P.O. BOX 280
DEER PARK, NY 11729
PH: 800 645-5538 FAX: 631 586-4220
EMAIL: [email protected]
WWW.ALARMCONTROLS.COM
JACK NUT INSTALLATION KIT
CONTENTS
ONE JACK NUT INSTALLATION TOOL
1 - 5M MANDREL INSTALLED IN INSTALLATION TOOL
50 - 5M x .75 FLAT HEAD PHILLIPS MACHINE SCREW
50 - 5M JACK NUTS
1 - 3M MANDREL
1 - 4M MANDREL
1 - 6M MANDREL
TO REORDER ADDITIONAL JACK NUTS AND SCREWS
USE P/N JN-50
PACKAGE CONSISTS OF
5O - 5M JACK NUTS
50 - 5M x .75 FLAT HEAD PHILLIPS MACHINE SCREWS
MANDREL
MANDREL
NOSEPIECE
MANDREL
LOCKNUT
MANDREL
STOP PIN HOLE
JACK NUT
RELEASE KNOB
STROKE
ADJUSTMENT
SCREW
STROKE
ADJUSTMENT SCREW
LOCKNUT
MANDREL
STOP PIN
STORAGE
MANDREL
WRENCH
JACK NUT INSTALLATION TOOL JACK NUT INSTALLATION
STEP 1
STEP 3
STEP 2
THREAD JACK NUT ONTO THE MANDREL
OF THE INSTALLATION TOOL. THEN PUSH
THE JACK NUT ALL THE WAY INTO THE
PRE-DRILLED HOLE,(25/64” DRILL), UNTIL
THE FLANGE OF THE JACK NUT IS FIRM-
LY AGAINST DOOR FRAME.
SQUEEZE HANDLES OF INSTALLATION
TOOL UNTIL JACK NUT IS FULLY COL-
LAPSED. THEN UN-SCREW MANDREL
WITH THE JACK NUT RELEASE KNOB.
PASS FLAT HEAD 5M MACHINE SCREW
THROUGH HEADER PLATE AND TIGHTEN
SCREW UNTIL SNUG.
TO CHANGE MANDREL
(JACK NUT TOOL HAS 5M MANDREL INSTALLED)
STEP 1 REMOVE STOP PIN FROM STORAGE COMPARTMENT.
STEP 2 ROTATE JACK NUT RELEASE KNOB UNTIL THE STOP
PIN HOLES LINE-UP AND INSERT STOP PIN.
STEP 3 UN-SCREW MANDREL NOSEPIECE. REMOVE LOCK NUT
FROM NOSEPIECE.
STEP 4 USE MANDREL WRENCH TO UN-SCREW MANDREL.
ROTATE WRENCH CLOCKWISE TO UN-SCREW.
STEP 5 RE-ASSEMBLE NOSEPIECE WITH LOCK NUT INSTALLED.
DOOR
FRAME
COLLAPSED
JACK NUT
HEADER
PLATE
/