Clover CDR-1610 User manual

USER’S MANUAL

Stand-Alone 16channel

DIGITAL VIDEO RECORDER

MODEL CDR1610

CAUTION

RISK OF ELECTRONIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRONIC SHOCK,

DO NOT REMOVE COVER (OR BACK). NO USER

SERVICEABLE PARTS INSIDE. REFER SERVICING

TO QUALIFIED SERVICE PERSONNEL.

Graphic Symbol Explanation

This symbol is intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in the literature

accompanying the product.

This symbol is intended to alert the user to the presence of uninsulated

“dangerous voltage” within the product’s enclosure that may be of sufficient

magnitude to constitute a risk of electric shock to persons.

- 2 -

IMPORTANT SAFEGUARDS AND WARNINGS

1. Read Owner’s Manual

All the safety and operating instructions should be

read before this product is operated.

2. Follow Instructions

All operating and use instructions should be

followed.

3. Power Sources

This product should be operated only from the type

of power source indicated on the marking label. If

you are not sure of the type of power supply to your

home or business, consult your product dealer or

local power company.

4. Power Cord Protection

Power-supply cords should be routed so that they

are not likely to be walked on or pinched by items

placed upon or against them, paying particular

attention to cords at plugs, convenience

receptacles, and the point where they exit from the

product.

5. Cleaning

Unplug this product from the wall outlet before

cleaning. Do not use liquid cleaners or aerosol

cleaners. Use a damp cloth for cleaning.

6. Water and Moisture

Do not use this product near water.

7. Attachments

Do not use attachments not recommended by this

product manufacturer as they may cause hazards.

8. Accessories

Do not place this product on an unstable cart, stand,

tripod, bracket, or table. The product may fall,

causing serious injury to a child or an adult, and

serious damage to the product. Use only with a cart,

stand, tripod, bracket, or table recommended by the

manufacturer, or solid with the product. Any

mounting of the product should follow the

manufacturer’s instructions and should use a

mounting accessory recommended by the

manufacturer. The product and cart combination

should be moved carefully. Quick stop, excessive

force, and uneven surfaces may cause the product

and cart combination to overturn.

9. Ventilation

Slots and openings in the cabinet are provided for

ventilation and to ensure reliable operation of the

product and to protect it from overheating, and

these openings must not be blocked or covered.

This product should not be placed near or over a

radiator or heat register. This product should not be

placed in a built-in installation such as a bookcase

or rack unless proper ventilation is provided or the

manufacturer’s instructions have been adhered to.

10. Lightning

For added protection for this product during a

lightning storm, or when it is left unattended and

unused for long periods of time, unplug it from the

wall outlet and disconnect the cable system. This

will prevent damage to the product due to lightning

and power-line surges.

11. Overloading

Do not overload wall outlets and extension cords as

this can result in a risk of fire or electric shock.

12. Object and Liquid Entry

Never push objects of any kind into this product

through openings as they may touch dangerous

voltage points or short-out parts that could result in

a fire or electric shock. Never spill liquid of any kind

on the product.

13. Servicing

Do not attempt to service this product yourself as

opening or removing covers may expose you to

dangerous voltage or other hazards. Refer all

servicing to qualified service personnel.

14. Damage Requiring Service

Unplug this product from the wall outlet and refer

servicing to qualified service personnel under the

following conditions.

▶When the power-supply cord or plug is damaged.

▶If liquid has been spilled, or objects have fallen

into the product.

▶If the product has been exposed to rain or water.

▶If the product dose not operate normally by

following the operating instruction. Adjust only

those controls that are covered by the operating

instructions, as an improper adjustment of other

controls may result in damage and will often

require extensive work by a qualified technician

to restore the product to its normal operation.

▶If the product has been dropped or the cabinet

has been damaged.

▶When the product exhibits a distinct change in

performance this indicates a need for service.

15. Replacement Parts

When replacement parts are required, be sure the

service technician has used replacement parts

specified by the manufacturer or have the same

characteristics as the original part. Unauthorized

substitutions may result in fire, electric shock or

other hazards.

16. Safety Check

Upon completion of any service or repairs to this

product, asks the service technician to perform

safety checks to determine that the product is in

proper operating condition.

- 3 -

Table of Contents

■ Chapter 1: Introduction…….………………..………………………………….. 5

Technical Specifications..……….……………………………………………………. 6

Installation………………………………….……………………………………….. 7

■ Chapter 2: Operation Mode…….…….…….…………………………………. 13

General Information…………………………………………………………………... 14

Power On/Off………………………………………………………………………….. 14

Display Screen……………………………………………………………………….. 15

System Status………………………………………………………………………….. 21

PTZ Control………………………………………………………………………….. 23

How to Record…………………………………………………………………….. 24

How to Replay ……………………………………………………………………….. 25

How to Backup ……………………………………………………………………….. 29

■ Chapter 3: Setup Mode…….…………………………………………………… 34

Setup Window…….….…………………………………………………………... 35

System…………….…………………………………………………………… 35

Time / Date……………….…………………………………………………………… 40

Disk Manager……………..………………………………………………………….. 42

Camera………………..………………………………………………………….. 43

Record Configuration……..………………………………………………………….. 45

Motion Configuration……..………………………………………………………….. 51

Sensor Configuration……..………………………………………………………….. 55

Network Configuration……..………………………………………………………….. 57

Pan/Tilt Configuration……..………………………………………………………….. 59

System Information………..………………………………………………………….. 60

Color Setting……………..………………………………………………………….. 61

■ Chapter 4: HDD Installation…………………………………………………... 63

General Information……………………………………………………………….. 64

How to Install………….………………………………………………………………. 64

■

Chapter 5: Remote Host Software…………………………………………... 65

Software Installation………………………………………………………………….. 66

Remote Host Screen….………………………………………………………………. 66

Backup Search…………..……………………………………………………………. 73

■

Appendix.……………………………..…………………….……………………… 75

Recording Time Table ………..…………………………………..…………………. 75

Factory Default Table. ……………………………………………..…………………. 75

■ FAQ…….……………………………………………………………………………….. 77

■

Limited 2year Warranty……………..…………………….……………………… 79

■

How to Obtain Factory Service……………………………………………….. 79

- 4 -

Chapter

1

Introduction

■ Technical Specifications

■ Installation

- 5 -

1.1 Technical Specifications

■ CDR1610 (16ch DVR)

ITEM DESCRIPTION

SYSTEM

System Control Front Keypad, Jog Shuttle, Mouse (PS2), IR Remote Controller

Operating System (O/S) RTOS in Firmware

Operating Help Support Instant OSD

Language English, Chinese, Japanese, Korean

VIDEO

Video Format NTSC/PAL

Video Inputs 16 Channels (BNC)

Video Outputs Main Monitor, SVHS, VGA (DSUB)

Looping Outputs 16 Channels (BNC)

Display Resolution 720x480 (NTSC), 720x576 (PAL)

Display Speed (Real-Live) 480 FPS (NTSC), 400 FPS (PAL)

Screen Division 1, 4, 5, 8, 9, 10, 13, 16 Camera Window Dragging

RECORDING

Recording Resolution 360x240, 720x240 (NTSC) / 360x263, 720x263 (PAL)

Recording Speed 0.5 FPS ~ 120 FPS (Auto Max. Recording Detect)

Recording Options Time Schedule / Manual / Alarm Sensor / Motion Detection

Compression Technology Wavelet

Compression Rate 4:1 ~ 250:1

Image Quality 1~30 Levels

HDD Storage (IDE) 3 x Internal HDD, 1 x Removable HDD

SEARCH

Search Options Manual, Camera, Time, Alarm Event

Playback Speed x64 Fast, Normal, Frame by Frame (Forward / Backward)

BACKUP

Backup Device / Options USB Drive, Ethernet / Time, List

PAN/TILT

PTZ Control RS-485, 16 Camera PTZ, Remote Control

ALARM

Alarm Sensor Inputs 16 Ports, NC/NO Selectable

Alarm Control Outputs 4 Ports, (3A Max.)

Alarm Dwell Time 1~10 sec

NETWORK

Networking Interface Ethernet (10/100Mbps), RJ-45, TCP/IP (Dynamic to Dynamic)

Remote Access Max. 4 Client Connection (Live View, Playback, Configuration, PTZ)

OTHERS

Electrical Power / Consumption AC 110V or 220V (50~60Hz) / Approx. 160 Watt

Operating Temperature 5℃ to 40℃ (41℉ to 104℉)

Operating Humidity 10 to 90% RH, Non-Condensing

Dimensions 425(W) x 390(D) x 90(H) mm

Unit Weight Approx. 10 kg (Without HDD)

- 6 -

1.2 Installation

■ Package Contents

• Digital Video Recorder

• AC Power Cord

• Remote Controller

• Mouse (P/S-2)

• Rack Mount bracket and bolts

• Remote Client Software (CD-ROM)

• User’s Manual

■ Installation Steps

• Connect the cameras, the DVR unit and monitor (Refer to [Fig 5-3]).

• Connect the AC power cord to the DVR.

• Confirm live video is displayed on the monitor before going to the next step.

• Select Set Menu and set current date and time. (Refer to Part 7. Setup)

• Run Factory Default menu on the SYSTEM menu.

• Perform HDD formatting.

• Escape from set Menu.

• Set values for required options.

• Network cable should be connected to the DVR unit before turning the power on.

Refer to [Fig 5-8] for the cable specification.

■ Front Panel

Figure 1-1: Front Panel

6

7

8 9

5 4 321

Figure 1-1

1. USB Connector

2. Power Button

3. Video Channel & Split Screen Button

4. Function Button

5. Jog & Shuttle

6. Removable HDD Rack

7. HDD – HDD status display LED, LINK – Ethernet LINK status display LED,

DATA – Ethernet Data status display LED

8. Mouse (P/S2)

9. IR Receiver for Remote Controller

- 7 -

■ Video Channel & Split Button

171615 1413

1211 10

9

87 6

5

43 2 1

Figure 1-2: Video Channel & Split Button

Figure 1-2

1. No.1 Channel (Full Screen), 4A(Split Screen)

2. No.2 Channel (Full Screen), 4B(Split Screen), Up Key

3. No.3 Channel (Full Screen), 4C(Split Screen)

4. No.4 Channel (Full Screen), 4D(Split Screen)

5. No.5 Channel (Full Screen), 9A(Split Screen), Left Key

6. No.6 Channel (Full Screen), 9B(Split Screen), Enter Key

7. No.7 Channel (Full Screen), 5(Split Screen), Right Key

8. No.8 Channel (Full Screen), 8(Split Screen)

9. No.9 Channel (Full Screen), 10(Split Screen)

10. No.10 Channel (Full Screen), 13A(Split Screen), Down Key

11. No.11 Channel (Full Screen), 13B(Split Screen)

12. No.12 Channel (Full Screen), 16(Split Screen)

13. No.13 Channel (Full Screen)

14. No.14 Channel (Full Screen)

15. No.15 Channel (Full Screen)

16. No.16 Channel (Full Screen)

17. Main Window

■ Function Button

8 7

6 5

4

3

2 1

Figure 1-3

1. Display (Full / Split)

2. Emergency Record

3. Zoom

4. Quick Replay

5. Freeze

6. Setup

7. OSD / Sensor

8. Stop (ESC)

Figure 1-3: Function Button

- 8 -

■ Rear Panel

Figure 1-4: Rear Panel

11

10

9876 5 4

3 2

1

Figure 1-4

1. Camera Input & Loop Output

2. Main Monitor

3. Power Input

4. VGA Monitor

5. S-VHS Monitor

6. Ethernet Port

7. RS-485 Port

8. Sensor Alarm Input

9. Control Relay Output

10. Mouse (P/S2)

11. Voltage Selector

■ Camera Connection

1. Camera Input

Connect the cameras to Video Input (BNC connector) on the back of the unit.

2. Loop Output

The Camera or video output is available from the Loop Output on the back of the

unit. When BNC jack is connected to the Video Output, the termination resistance

(75Ω) is automatically switched to impedance status so the external device must

have termination resistance

- 9 -

■ Monitor Connection

1. Main Monitor

Connect the monitor to "Main" on the upper part of BNC connector.

2. S-VHS Monitor

Connect the S-VHS monitor to "S-VHS" DIN jack on the rear of the unit.

Output for S-VHS monitor is the same as that of main or auxiliary and has a

separate output buffer and works independently.

Figure 1-5: S-VHS Connector

3. VGA Monitor

Connect the VGA monitor to DSUB-15 Pin Connector on the rear of the unit.

Figure 1-6: VGA Connector

■ Sensor and Relay Connection

1. Sensor Alarm Input

Connect the sensor to ALARM-IN. The Sensor should be contactor type and

support NO (Normal Open).

2. Control Relay Output

The Output of RELAY-OUT is a relay contactor type and supports NO (Normal

Open), NC (Normal Close). The Output capacity is 220V 1A and a higher capacity

can cause system failure.

Figure 1-7: Sensor and Relay Connector

- 10 -

■ RS-485 Connection

Using the RS-485 Terminal Block you can connect to the RS-485 cable up to 1 Km.

Figure 1-8: RS-485 connection for PTZ camera

■ Ethernet Connection

Ethernet connector is a RJ45 type. The maximum cable length is 100m. When you

would like to use a longer cable, you cane use repeater.

Figure 1-9: Ethernet connection

- 11 -

■ Power Cable Connection

Input the power after selecting power voltage of back side of system. Input voltage

tolerance is 10% and we can not warranty if you are using the over tolerance around

10%. If the electric system is not stable, please using the UPS or AVR.

Standard Input voltage: AC110V 50/60Hz or AC220V 50/60Hz

Figure 1-10: Input power selection

CAUTION: FACTORY DEFAULT SETTING IS AC110V 50/60Hz IN POWER

SELECT SWITCH. PLEASE DOUBLE CHECK BEFORE YOU INPUT

THE POWER INTO THE SYSTEM.

■ PAL / NTSC Selection

PAL or NTSC is set at the factory according to the country where the system is

shipped. If necessary, it can be reset as follows;

• Turn off the system, and then remove the cover.

• Reset the PAL/NTSC selection jumper (NTSC: open, PAL: close). Please refer

to Figure 4-1.

• Reassemble the cover.

• Turn on the system and format the HDD.

NOTE: WHEN THIS SETTING IS CHANGED, YOU WILL LOSE ALL OF YOUR

RECORDED DATA AND SETTINGS.

YOU SHOULD SET THE SYSTEM AGAIN AFTER THIS PROCEDURE.

- 12 -

Chapter

2

Operation Mode

■ General Information

■ Power On/Off

■ Display Screen

■ System Status

■ PTZ Control

■ How to Record

■ How to Replay

■ How to Backup

- 13 -

2.1 General Information

You can operate all functions of the system by use of the 26 buttons located on the front

panel and a mouse. Also you can remotely control this unit via RS-485 or the Ethernet

port located on the backside.

System status is indicated by either LED light on the operator buttons or the monitor.

The system is protected from any inadvertent pressing of any operator buttons. But care

should be taken when using the functions of HDD Formatting as then can lead to data

loss. To avoid any mistake, the re-confirmation is required when these functions are

selected.

2.2 Power On/Off

▪ Power On: Push the “POWER” button in the front panel for 5 seconds.

▪ Power Off: Push the “POWER” button in the front panel for 5 seconds or click the

mouse’s right button on the power off screen.

Figure 2-1: Power off

- 14 -

2.3 Display Screen

■ Camera View

Figure 2-2: Full screen

2

0

5

/

0

1

/

0

1

2

0

:

2

5

:

4

3

C

A

M

0

1

3

1

Figure 2-2

1. Status Icon: Record, Backup, Motion or Freeze, Sensor

2. Camera Name

3. Current Time

■ Screen Division

4A~4D Split screen 5 Split screen 8 Split screen 9 Split screen

10 Split screen 13A Split screen 13B Split screen 16 Split screen

- 15 -

■ Live Main Window

▪ Press the “MAIN” button or Click the mouse’s right button on the live screen.

▪ It will show the Live Main Window.

▪ Click the “EXIT” button, and it will return to the Live Screen.

Figure 2-3: Live Main Window

■ Switching a Specific Screen

By clicking one screen and drag & drop to another screen, you can switch a specific

screen on the Live Screen. This Window is always occupied this position also in replay

mode. The following example shows that #2 camera and #6 camera screens are switched

each other.

C1

C2

C3 C4

C5 C7

C8

C6

C9

C10 C11 C12 C13

2 <=> 6

Figure 2-4: Switching a specific screen

- 16 -

■ Split Screen

▪ Split screen is possible in the LIVE mode or RECORD mode.

▪ Click the “SPLIT” button, and choose the desired split screen with the mouse’s wheel or

“UP/DOWN” button. To complete the setting and close the Live Main Window, click the

“SPLIT” button again. It will show the Live Main Window.

▪ It is available to change into various SPLIT modes with buttons on the front panel. To

change into SPLIT mode, Press the “Display” Key on the front panel.

Figure 2-5: Changing a split screen

■ Full Screen

▪ Full screen is possible in the LIVE mode or RECORD mode.

▪ Click the “FULL” button, and choose the desired full channel with the mouse’s wheel or

“UP/DOWN” Keys. To complete the setting and close the Live Main Window, click the

“FULL” button again.

Figure 2-6: Full screen

- 17 -

■ Sequential Screen

▪ Sequential screen is possible in the LIVE mode or RECORD mode.

▪ Display each channel in turn after setting auto switching of video input channel.

▪ To display the sequential screen and close the LIVE MAIN Window, press the

“SEQUENCE” button again.

Figure 2-7: Sequential screen

■ OSD(On Screen Display) On/Off

▪ OSD On/Off is possible in the LIVE mode or RECORD mode.

▪ When the “OSD” button is clicked, Live Main Window is closed and all the texts except

for the video display are deleted temporarily.

▪ When the button is clicked again while OSD is in OFF position, the system status will be

the normal condition. It is available to use pressing the “OSD” button on the front panel.

■ Zooming Screen

▪ Zooming screen is possible in the LIVE mode or RECORD mode. This function is

available in the full screen mode only.

▪ It is available to zoom 1x~4x. To display the zoom screen and close the Live Main

Window, click the “ZOOM” or press the “ZOOM” button on the front panel.

▪ To complete zoom mode, click the mouse’s right button on the zoom screen, and then

click the “ZOOM” or press the “ZOOM” button on the front panel.

Figure 2-8: Zoom button

- 18 -

Figure 2-9: Zooming screen

▪ ZOOM IN: Click the ‘+’ button or Press “UP/DOWN/LEFT/RIGHT” button on the front

panel.

▪ ZOOM OUT: Click the ‘-’ button or Press “UP/DOWN/LEFT/RIGHT” button on the front

panel.

▪ MOVE: Click the ‘Arrow’ button or press UP/DOWN/LEFT/RIGHT” button on the Front

panel to move each direction of Zoom screen.

▪ PIP On/Off: Click the mouse’s left button in part of not PIP screen or press the “ENTER”

button on the front panel.

▪ OSD On/Off: If you click the mouse left button when you are not using the PIP Window,

or “ESC” button on the front panel, OSD will On/Off.

■ Freeze

▪ Freeze is possible in the LIVE mode or RECORD mode. This function is available in the

full screen mode only.

▪ To display the Freeze mode, click the “FREEZE” button on the Live Main Window or

press the “FREEZE” button on the front panel.

▪ To complete the Freeze mode, click the “FREEZE” button again on the Live Main

Window or press the “FREEZE” button on the front panel again.

▪ Freeze On/Off: Click the mouse’s left button or press the “ENTER” button on the front

panel.

Figure 2-10: Freeze screen

- 19 -

■ Camera/VGA Enhance

▪ Click the “CAM/VGA ENHANCE” button on the Live Main Window, and then select the

Camera enhance or VGA enhance by using mouse’s wheel or “UP/DOWN” button on

the front panel.

▪ Select the channel to set Contrast / Brightness for camera or Contrast / Brightness /

Saturation for VGA by using the mouse or the “UP/ DOWN/LEFT/RIGHT” button on the

front panel.

▪ It will show the camera / VGA control Window when you click the mouse’s right button or

the “ENTER” button on the front panel.

▪ To return to the LIVE MAIN Window, click the mouse’s right button or press the “ESC”

button on the front panel.

Figure 2-11: Video enhance button

▪ Click the Contrast / Brightness / Saturation Bar button with mouse’s left button or

“ENTER” button on the front panel. The color of bar is indicated in yellow and the

setting value of video is changed.

▪ Click the (EXIT) button, and it will show the channel selection Window. Click the mouse’s

right button or “ESC” button on the front panel, it will show Live Main Window.

Figure 2-12: Contrast / Bright / Saturation control

- 20 -

Page is loading ...

Clover CDR-1610 User manual

Related papers

Other documents