Datalogic GWY-01-PBS-01 Reference guide

Brand: Datalogic

Model: GWY-01-PBS-01

Category: Networking

Type: Reference guide

GWY-01-PBS-01

Reference Manual

Datalogic Automation Srl

Via S. Vitalino, 13

40012 - Lippo di Calderara di Reno

Bologna - Italy

GWY-01-PBS-01 Reference Manual

Ed.: 02/2010

U.S. and international laws. Copying, or altering of this document is prohibited without express written

consent from Datalogic Automation S.r.l.

Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. in many countries,

including the U.S.A. and the E.U.

Subnet16 and Cobalt Dashboard are trademarks of Datalogic Automation S.r.l. All other brand and

product names mentioned herein are for identification purposes only and may be trademarks or

registered trademarks of their respective owners.

Datalogic shall not be liable for technical or editorial errors or omissions contained herein, nor for

incidental or consequential damages resulting from the use of this material.

26/02/10

iii

CONTENTS

REFERENCES ............................................................................................................vi

Conventions................................................................................................................. vi

Reference Documentation........................................................................................... vi

Services and Support .................................................................................................. vi

SAFETY AND COMPLIANCE NOTICES...................................................................vii

FCC Compliance .........................................................................................................vii

Power Supply...............................................................................................................vii

CE Compliance............................................................................................................vii

GENERAL VIEW.......................................................................................................viii

1 GETTING STARTED....................................................................................................1

1.1 Introduction...................................................................................................................1

1.1.1 The Subnet16™ Gateway ............................................................................................1

1.2 Subnet16 Profibus Gateway Features..........................................................................1

1.3 About this Manual.........................................................................................................2

1.3.1 Who Should Read This Manual?..................................................................................2

1.3.2 HEX Notation................................................................................................................2

1.4 Gateway Dimensions....................................................................................................3

1.5 Installation Guidelines...................................................................................................4

1.5.1 Hardware Requirements...............................................................................................4

1.5.2 Installation Precautions.................................................................................................4

1.5.3 Network & Power Considerations.................................................................................4

1.5.4 Maximum Supported Trunk and Drop Cable Lengths ..................................................5

1.6 Installing the Gateway ..................................................................................................5

1.7 Additional Application Specific Configuration ...............................................................6

1.8 USB Driver Installation..................................................................................................7

1.9 Gateway Profibus Configuration using Cobalt Dashboard™......................................11

2 GATEWAY OVERVIEW .............................................................................................13

2.1 Operating Modes ........................................................................................................13

2.1.1 Subnet16™.................................................................................................................13

2.2 LED Indicators ............................................................................................................14

2.2.1 Front Panel LEDs .......................................................................................................14

2.3 External Connectors ...................................................................................................14

2.3.1 Profibus.......................................................................................................................15

2.3.2 USB ............................................................................................................................15

2.3.3 Subnet16™ RS485.....................................................................................................16

2.4 Power & Wiring...........................................................................................................16

2.4.1 Power Requirements ..................................................................................................16

2.4.2 Total System Current Consumption............................................................................17

2.4.3 Cable Voltage Drop ....................................................................................................17

2.4.4 Current Rating for Cables...........................................................................................18

2.5 Node ID Configuration & Management.......................................................................18

2.6 Gateway and Subnet Node Naming ...........................................................................19

2.7 Configuration Tools.....................................................................................................20

2.7.1 Cobalt Dashboard™ ...................................................................................................20

2.7.2 C-Macro Builder™ ......................................................................................................21

3 RFID COMMAND MACROS ......................................................................................22

3.1 What are RFID Command Macros? ...........................................................................22

3.2 Why use macros?.......................................................................................................22

3.3 What can macros do?.................................................................................................22

3.4 What is a macro trigger?.............................................................................................22

3.5 How are macros created?...........................................................................................23

3.6 Which communication interfaces support the use of macros? ...................................23

3.7 What happens to existing Macros if a controller must be replaced? ..........................23

3.8 How can I learn more about the Dashboard and C-Macro Builder? ...........................23

4 COMMAND PROTOCOL ...........................................................................................24

4.1 CBx Command Protocol Overview .............................................................................24

4.2 CBx - Command Packet Structure..............................................................................25

4.3 CBx - Response Packet Structure..............................................................................26

4.3.1 Instance Counter ........................................................................................................26

4.4 CBx Commands Table................................................................................................27

4.5 CBx Command Protocol Examples ............................................................................29

4.5.1 CBx - Controller Command Example..........................................................................29

4.5.2 CBx - Controller Response Example ..........................................................................30

4.5.3 CBx - Gateway Command Example ...........................................................................30

4.5.4 CBx - Gateway Response Example ...........................................................................31

4.6 Node Status Byte Definition Table..............................................................................32

4.7 CBx Error Response Packet Structure .......................................................................33

4.8 CBx Error Code Table ................................................................................................34

4.9 CBx - Error Response Example..................................................................................35

4.10 Notification Messages.................................................................................................36

4.10.1 Notification Message Table ........................................................................................37

4.10.2 Notification Mask Example .........................................................................................37

4.10.3 Notification Message Packet Structure.......................................................................38

5 PROFIBUS INTERFACE............................................................................................39

5.1 Profibus Overview.......................................................................................................39

5.2 Profibus-DP ................................................................................................................39

5.3 Data Exchange ...........................................................................................................40

5.4 Protocol Implementation.............................................................................................41

5.4.1 Definitions...................................................................................................................41

5.4.2 Control Field ...............................................................................................................42

5.4.3 SAP Field....................................................................................................................45

5.4.4 Length Field................................................................................................................45

5.4.5 Application Data Buffer...............................................................................................46

5.5 Examples of Profibus Command/Response Mechanism............................................46

5.5.1 Example 1: Normal Command/Response Sequence .................................................48

5.5.2 Example 2: Unsolicited Responses (Continuous Read Mode) ...................................58

5.5.3 Example 3: Fragmentation of Responses...................................................................62

5.5.4 Example 4: Fragmentation of Commands ..................................................................71

5.5.5 Example 5: Resynchronization ...................................................................................82

6 TECHNICAL FEATURES...........................................................................................87

A MODELS AND ACCESSORIES ................................................................................88

Datalogic Automation RFID Tags ...............................................................................89

B EXAMPLE NETWORK LAYOUTS.............................................................................90

Subnet16™ Gateway –ThickNet Network Layout ......................................................90

Subnet16™ Gateway –ThinNet Network Layout ........................................................91

ASCII CHART.............................................................................................................92

REFERENCES

CONVENTIONS

This manual uses the following conventions:

“User” or “Operator” refers to anyone using a GWY-01-PBS-01.

“Device” refers to the GWY-01-PBS-01.

“You” refers to the System Administrator or Technical Support person using this manual to

install, mount, operate, maintain or troubleshoot a GWY-01-PBS-01.

Throughout this manual, the GWY-01-PBS-01 is referred to as the “Subnet16 Gateway” or

simply “the Gateway”.

Cobalt C-Series, HF-Series and UHF-Series RFID Controllers are referred to as Cobalt

Controllers, or just “the Controller”.

In addition, the terms “Subnet Node Number”, “Node ID” and “Controller ID” are used

interchangeably.

REFERENCE DOCUMENTATION

The documentation related to the GWY-01-PBS-01 management is available at the website:

www.automation.datalogic.com

SERVICES AND SUPPORT

Datalogic provides several services as well as technical support through its website. Log on

to www.automation.datalogic.com and click on the

UlinksU indicated for further information

including:

 PRODUCTS

Search through the links to arrive at your product page where you can download specific

Manuals

and Software & Utilities including:

- Cobalt Dashboard™ a Windows-based application that provides users with complete

control over their Datalogic Automation RFID hardware. Users can monitor their entire

RFID infrastructure - from the tag level, to the RFID controller, to the Gateway and to

the Host. It provides device configuration through serial and TCP/IP interfaces

depending on the device type.

- C-Macro Builder™ is an easy to use GUI-driven utility for Windows. This software tool

allows users with minimal programming experience to “build” their own macro programs

(which are stored internally on and executed directly by Cobalt RFID Controllers).

 SERVICES & SUPPORT

- Datalogic Services

- Warranty Extensions and Maintenance Agreements

- Authorised Repair Centres

 CONTACT US

E-mail form and listing of Datalogic Subsidiaries

vii

SAFETY AND COMPLIANCE NOTICES

FCC COMPLIANCE

Modifications or changes to this equipment without the expressed written approval of

Datalogic could void the authority to use the equipment.

This device complies with PART 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device must

accept any interference received, including interference which may cause undesired

operation.

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the user will be required to correct

the interference at his own expense.

POWER SUPPLY

This product is intended to be installed by Qualified Personnel only.

This device is intended to be supplied by a UL Listed or CSA Certified Power Unit with

«Class 2» or LPS power source.

CE COMPLIANCE

Warning:

This is a Class A product. In a domestic environment this product may cause radio

interference in which case the user may be required to take adequate measures.

viii

GENERAL VIEW

GWY-01-PBS-01

Figure A

Power On LED

Subnet16 Connecto

Profibus Status LED

Configuration Error LED

Profibus Mode LED

Subnet16 BUS LED

US B Con nect or

Profibus Connector

Mounting Bracket

GETTING STARTED

1 GETTING STARTED

1.1 INTRODUCTION

Welcome to the GWY-01-PBS-01 Reference Manual. This manual will assist you in the

installation, configuration and operation of Datalogic Automation Subnet16™ Profibus

Gateway Interface Module.

The Profibus Gateway can control up to 16 passive ultra-high or high frequency read/write

Radio-Frequency Identification (RFID) controllers. In order to meet and exceed the

requirements of the industrial automation industry, the Profibus Gateway and Datalogic

Automation RFID controllers are designed to be compact, reliable and rugged.

1.1.1 The Subnet16™ Gateway

Subnet16™ is a 16-Node Multidrop bus architecture and protocol that provides connectivity

for up to 16 RFID controllers through a single Gateway device.

The Profibus Gateway supports Profibus -DP communications and can be connected to a

Programmable Logic Controller (PLC) via Profibus compatible cabling. It’s compatible with

Datalogic Automation Cobalt UHF-Series, HF-Series and C-Series RFID controllers, reading

LRP, HMS and T-Series RFID tags.

1.2 SUBNET16 PROFIBUS GATEWAY FEATURES

 Multi-Drop capable; controls up to 16 RFID reader/writers, each functioning

independently and simultaneously.

 Operational power is supplied directly from the Subnet 16™ network

 Small footprint provides ease of mounting (104 x 107 x 32 mm).

 Galvanically isolated Profibus interface with auto baud rate detection 9.6 kbit/s - 12

Mbit/s

 Selectable Profibus node addressing (0 to 128), default is 63

 LED status indicators for Power/Ready, Subnet16 bus activity, Profibus mode,

Profibus network status, Configuration error indication

 Supports controller macro functionality

 Flash memory for software updates

 Real-time Calendar/Date functions

 Auto configuration of RFID controllers, automatic Node ID number assignment

 Node Fault Detection

 Isolated bus interfaces

GWY-01-PBS-01

1.3 ABOUT THIS MANUAL

This manual provides guidelines and instructions for installing, configuring and operating

Datalogic Automation's Subnet16 Profibus Gateway Interface Module (GWY-01-PBS-01).

This document does NOT include explicit details regarding each of the Gateway’s RFID

commands. Specific RFID command related information is available in the CBx Command

Protocol – Reference Manual, which is available at www.automation.datalogic.com.

However, this manual does explain the process of issuing commands from a host PC or

Programmable Logic Controller (PLC) to a Subnet16 Gateway, Subnet network and attached

RFID controllers.

1.3.1 Who Should Read This Manual?

This manual should be read by those who will be installing, configuring and operating the

Gateway. This may include the following people:

 Hardware Installers

 System Integrators

 Project Managers

 IT Personnel

 System and Database Administrators

 Software Application Engineers

 Service and Maintenance Engineers

1.3.2 HEX Notation

Throughout this manual, numbers expressed in Hexadecimal notation are prefaced with “0x”.

For example, the number "10" in decimal is expressed as "0x0A" in hexadecimal. See

Appendix C for a chart containing Hex values, ASCII characters and their corresponding

decimal integers.

GETTING STARTED

1.4 GATEWAY DIMENSIONS

[3.24]

104

[4.08]

[3.50]

40.7

[1.60]

7.6

[0.30]

91.4

[3.60]

107

[4.20]

[1.27]

Ø5.0

[Ø0.20]

Ø10.2

[Ø0.40]

N° 2

Figure 1: GWY-01-PBS-01 Dimensions

GWY-01-PBS-01

1.5 INSTALLATION GUIDELINES

1.5.1 Hardware Requirements

The following components are required for a complete Subnet16 RFID system:

 One Subnet16 Profibus Gateway Interface Module

 One Profibus-capable host; Programmable Logic Controller (PLC) or PC

 One to 16 RFID controllers (Cobalt C-Series, HF-Series or UHF-Series Controllers -

RS485 models)

 Adequate length cabling, connectors and terminators

 Sufficient power, supplied via Subnet16 network cabling, capable of powering the

Gateway and its RFID controllers

 Datalogic Automation RFID series tags: HMS, LRP, T/Gamma, I, or UHF-G2-525

1.5.2 Installation Precautions

 Do not route cables near unshielded cables or near wiring carrying high voltage or

high current. Cross cables at perpendicular intersections and avoid routing cables

near motors and solenoids.

 Review the power requirements of your RFID network and provide a suitable power

supply.

 Avoid mounting the controller near sources of EMI (electro-magnetic interference) or

near devices that generate high ESD (electro-static discharge) levels. Always use

adequate ESD prevention measures to dissipate potentially high voltages.

 If electrical interference is encountered (as indicated by a significant reduction in

read/write performance), relocate the controller to an area free from potential sources

of interference.

 Perform a test phase by constructing a small scale, independent network that

includes only the essential devices required to test your RFID application (use

Datalogic Automation approved Subnet16™ cables and accessories).

1.5.3 Network & Power Considerations

 Refer to the network diagrams in Appendix B. Choose the network architecture

(ThickNet vs. ThinNet) that best suits your RFID requirements.

 Construct your chosen network using only Datalogic Automation approved

Subnet16™ cables, Drop-T connectors, Terminating Resistors and accessories.

 Review the power requirements of your RFID network and provide a suitable power

supply. (See Appendix A for power supplies offered by Datalogic Automation).

NOTE

It is recommended that power be applied directly to the Subnet16™ Network

trunk and distributed through drop cables to the Gateway and RFID

controllers. By positioning the power supply near the middle of the network

(see examples), you can limit voltage drop at the ends.

GETTING STARTED

1.5.4 Maximum Supported Trunk and Drop Cable Lengths

 ThickNet trunk length up to 300 m.

 ThinNet trunk length up to 20 m.

 ThinNet drop cable length up to 2 m.

1.6 INSTALLING THE GATEWAY

The numbered steps in the following procedure are also indicated in the SubNet16 networks

example layouts shown in Appendix B.

1. Preliminary Notes: Read the Installation Guidelines in par. 1.5.

2. Mounting: Mount the Gateway to your chosen location using two M5 (#10) screws,

lock washers and nuts. The Gateway may be mounted in any orientation, but should

be aligned in such a manner that the LED indicators can be seen during operation.

3. Gateway Connection: Attach one end of a 5-pin, male-to-male, M12, ThinNet drop

cable (P/N: CBL-1481-XX) to the 5-pin, female, M12 connector on the Gateway.

Connect the other end of this 5-pin, male-to-male, M12, ThinNet drop cable to the 5-

pin, female, M12 connector on EITHER a ThickNet to ThinNet Drop-T Connector

OR a ThinNet to ThinNet Drop-T Connector (as per your network and RFID

application requirements).

4. Trunk Wiring: Attach one end of a male-to-female trunk cable to each mating

connector on the Drop-T Connector. Continue connecting trunk cables and Drop-T

connectors as needed.

Note: trunk length should not exceed 300 m for ThickNet and 20 m for ThinNet.

5. RFID Controller Connection: Connect the male end of a 5-pin, male-to-female,

ThinNet drop cable to the female end on your Drop-T connector(s). Attach the

remaining female end of the ThinNet drop cable to the 5-pin, male, M12 connector on

a Cobalt UHF, Cobalt HF or C-Series Controller (RS485 models). Repeat Step 5

for each RFID controller you plan to install.

Note: maximum drop cable length is 2 m.

6. Termination Resistors: For ThickNet Networks: Connect a Terminating Resistor

(P/N: CBL-1489, male) or (P/N: CBL-1497, female) to the first and last Drop-T

Connector on the trunk line.

For ThinNet Networks: Connect a Terminating Resistor (P/N: CBL-1490, male) or

(P/N: CBL-1496, female) to the first and last Drop-T Connector on the trunk line.

7. Power Supply Wiring: For ThickNet Networks: Using a 5-pin, female, 7/8 - 16,

ThickNet to Bare Wire Leads cable (P/N: CBL-1495-XX), connect the bare wires to

your power supply (SHIELD wire connected to Earth). Attach the female, ThickNet

end to the 5-pin, male, ThickNet end on a Drop-T connector (P/N: CBL-1526).

For ThinNet Networks: Using a 5-pin, female, M12, ThinNet to Bare Wire Leads cable

(P/N: CBL-1494-XX), connect the bare wires to your power supply (SHIELD wire

connected to Earth). Attach the female, ThinNet end to the 5-pin, male, ThinNet end

on a Drop-T connector (P/N: CBL-1486).

GWY-01-PBS-01

8. Host Connection: Connect the Gateway to the Profibus network via a Profibus-

compatible interface cable. Turn the power supply ON.

The POWER LED on the Gateway will remain lit while power is applied to the unit.

After the boot process is complete, the PBS Mode LED will also light up to indicate

the Gateway Profibus mode. It may appear green or red (solid or flashing) depending

on the status of the connection with your Profibus network (see par. 2.2 for the

behavior of the Gateway’s Profibus Mode LED).

9. Automatically Configure Subset16™ Node IDs: At this point all controllers are

powered and should have Node IDs set to 00, (all controller Node LEDs

= OFF), and

Subnet16™ baudrate = 9600 (factory defaults).

a. Place the RFID Controller Configuration Tag in front of an RFID Controller (the

controller's red RF Activity LED blinks once indicating the tag has been read), and

wait for the Gateway to assign a valid Node ID to it. The controller's Node LEDs

now indicate a valid Node ID. Remove the Configuration Tag from the controller.

b. Repeat this step for each node in the Subnet16™ network (one controller at a

time). The first is Node ID 1, then 2 and so on up to 16 (binary).

The Subnet16™ network is now configured with the default values and can communicate

with the Gateway Profibus which in turn communicates with the Master Profibus.

GWY-01-PBS-01 PROFIBUS FACTORY DEFAULTS

Node Address: 63

Input and Output Buffer size: 64 bytes

1.7 ADDITIONAL APPLICATION SPECIFIC CONFIGURATION

To modify the Gateway’s internal configuration for application specific requirements:

1. Install the USB Driver onto the configuration PC, see par. 1.8.

2. Download the Cobalt Dashboard™ utility from www.automation.datalogic.com and

install the software on your configuration computer. Use the Dashboard utility to

connect, via USB, to the Gateway. You will then be able to use the Cobalt Dashboard

Utility to configure the Gateway and send RFID commands for testing purposes. See

par. 1.9.

GETTING STARTED

1.8 USB DRIVER INSTALLATION

This paragraph contains instructions for installing the Windows 2000/XP USB driver for

Datalogic Automation RFID devices. Complete the following steps before installing the RFID

USB driver.

1. Download the RFID USB driver package from www.automation.datalogic.com.

2. Extract the driver files to a separate folder on your host computers’ Desktop.

3. Connect the USB interface cable (and power supply, if applicable) as described in the

Installation Guide included with your RFID product.

4. Apply power to your RFID device. Windows should detect the new hardware and start

the Found New Hardware Wizard. If it does not, run the Add Hardware applet in

Windows’ Control Panel.

Figure 2: Found New Hardware Wizard – Do Not Connect to Windows Update

Figure 3: Found New Hardware Wizard – Install From List

GWY-01-PBS-01

5. Select “Install from a list or specific location” and then click Next.

6. Check the box labeled: “Include this location in the search” and then click the Browse

button.

Figure 4: Found New Hardware Wizard – Include this Location

7. Browse to the folder containing the extracted RFID USB driver files and then click OK.

Figure 5: Found New Hardware Wizard - Browse for Folder

GETTING STARTED

8. Click Next to install the USB driver.

Figure 6: Found New Hardware Wizard – Ready to Install

Please wait while the Found New Hardware Wizard installs the USB driver.

Figure 7: Installing the USB Driver

GWY-01-PBS-01

9. After the USB driver has been installed, click Finish.

Figure 8: USB Driver Installation Complete

NOTE

Immediately after you click Finish, the Found New Hardware Wizard will

close and then automatically restart, prompting you to repeat the USB driver

installation. This occurs because Windows requires a second trip through

the installation routine to install and configure a virtual COM port for use by

the RFID USB device.

10. Repeat Steps 5-9 to install the virtual COM port and complete the installation of the

RFID USB driver.

Figure 9: Virtual COM Port USB Driver Installation Complete

GETTING STARTED

1.9 GATEWAY PROFIBUS CONFIGURATION USING COBALT

DASHBOARD™

The Cobalt Dashboard™ Utility is a software application that allows users to view, modify,

save and update the configuration settings of their Cobalt controllers. Follow the instructions

below to operate the Cobalt Dashboard Utility and to set the Cobalt device’s configuration.

1. Install the Gateway as described in par. 1.6.

2. Install the Cobalt USB driver to your PC as described in par. 1.8.

3. Connect the Gateway to your PC through the USB interface, power the network and

wait for the boot procedure to finish.

4. Run the Cobalt Dashboard™.

5. From the Connection screen, choose “Gateway Profibus”.

Figure 10: Cobalt Dashboard™ Gateway Profibus Selection

6. Choose the appropriate COM port and select 115200 Baud (this is the default serial

baud rate for USB connection); click “Connect”.

Figure 11: Cobalt Dashboard™ COM and Baudrate Selection

GWY-01-PBS-01

The Dashboard should send some commands to retrieve device and configuration

information from the device. If serial communications are set up correctly, the device

configuration area within the Cobalt Dashboard should now look like this:

Figure 12: Cobalt Dashboard™ Gateway Profibus Device Configuration Area

The default Profibus ID is 63, and the default Input and Output Buffer sizes are 64 bytes

each.

To change the Profibus ID of the device, and/or the Input Buffer/Output Buffer sizes, enter

the desired values in the appropriate boxes in the configuration tab, and click “Set Config”.

For Profibus, the new ID and buffer sizes will not take effect until the device is reset one

more time, or the power is cycled. Turn the unit off and back on to use the new ID and buffer

size settings. For other settings (such as Tag Type, continuous read parameters, etc), the

unit does not need to be reset again or have the power cycled.

See the Cobalt Dashboard™ User's Manual for more configuration details.

Page is loading ...

Datalogic GWY-01-PBS-01 Reference guide

Brand: Datalogic

Model: GWY-01-PBS-01

Category: Networking

Type: Reference guide

Download PDF

report

Datalogic GWY-01-PBS-01 Reference guide

Datalogic GWY-01-PBS-01 Reference guide

Related papers

Other documents