Slim Cooker Installation & Operating Instructions
INSTALLATION & OPERATING INSTRUCTIONS
STAINLESS STEEL GAS WOK COOKER
S3012NG, S3012PG, 3012NG &
3012PG-B S7012NG, S7012PG ,7012NG & 7012PG-B
FEATURES
Electronic ignition system incorporating piezo-electric elements.
S3012NG, S3012PG, S7012NG and S7012PG with flame failure safety device. Gas supply will be cut off
automatically if the burner flame extinguished accidentally to prevent gas leakage.
Wok burner suitable for all types of cooking from simmering to stir-frying.
High-energy, high-efficiency burner reduces gas consumption.
Large trivet for greater cooking flexibility.
Easy to clean stainless steel top and control panel.
IMPORTANT
Read this instruction manual in its entirety carefully and retain for future reference.
Familiarise yourself with the appliance before connecting the appliance to the gas cylinder
THE APPLIANCE MUST BE ASSEMBLED IN COMPLIANCE WITH MANUFACTURER’S
INSTRUCTIONS.
SAI GLOBAL APPROVAL NO.: GSCS20074
Web: www.auscrown.com
Slim Cooker Installation & Operating Instructions
WARNING
Important. Read these instructions carefully before use. Familiarise yourself with the appliance
before connecting it to its gas supply. Keep these instructions for future reference.
It is the operator’s responsibility to check the appliance is properly assembled and maintained
Do not lay the gas cylinder down – cylinder should be stored / used in the upright position
Hazardous fire or explosion may result if instructions are ignored.
Leak test all connections before use and after each cylinder refill
Never check for leaks with a match or open flame
Do not store or use petroleum products or other flammable vapours and liquids in the vicinity of this
appliance
Use only in well ventilated areas, but not facing against any draught.
WARNING! Carbon monoxide hazard – this appliance can produce carbon monoxide which
has no odour. Using the appliance in an enclosed space (for example, boats, caravan, tent,
car, and mobile home) may cause death.
Do not move the appliance during operation
Avoid twisting or kinking of the flexible gas hose
Do not use cooker near any air opening(s) into buildings (i.e. windows, doorways, ventilation ducts
etc.)
Leak test all connections before use and after each cylinder refill – refer “How to Check for Gas
Leaks” in this manual. NEVER check for leaks with a match or open flame.
An LP cylinder not connected for use in this appliance shall not be stored near this appliance.
Ensure the gas hose is not placed under the appliance or allowed to contact any hot surfaces of the
appliance
This appliance must not be modified or changed in any way.
Disconnect the gas cylinder from the wok cooker prior to storage. It is also recommended that the
gas cylinder be stored outdoors in a well-ventilated area.
Do not use any other gas type except the one specified on the label/data plate.
Use only the gas regulator specified in this instructions page or advised by your dealer. An inferior or
a damaged regulator could cause an incomplete combustion or other troubles with the burner.
Do not leave the burner unattended when in use. Always turn off the burner and the main gas valve
after each use.
Do not use the burner as a space heater under any circumstance.
Do not cover or blow out the flames. This could cause gas leaking.
Always keep flammable materials away from the burner.
Make sure that you use cooking woks, pots or pans that sit firmly on the trivet. Do not use pots that
are too small / large for the burner size, as they could be unstable on the trivet.
If abnormal combustion is observed when in use, turn off the main gas valve and examine the burner
(Refer to Trouble-Shooting Guide).
Do not spray aerosols in the vicinity of the burner when in use.
Children and adults should be alerted to the high temperatures of the cooker and its effect on
surrounding surfaces, clothing and skin
Children or the elderly should be supervised when near this appliance
Do not hang clothing or other flammable material on or near this appliance
If the cooker fails to operate correctly, contact place of purchase or their authorised agent for advice
and service. Do not continue to use the appliance and do not attempt repair yourself.
Make sure the gas inlet hose is clean and not blocked before connecting the gas.
Always ensure that adequate fresh air is provided for ventilation.
The cooker must only be operated on a level, firm non-combustible surface.
This cooker shall not be used in a position where it could create a fire hazard and the minimum
clearances to combustible materials must be observed, as described below.
A spider web can interfere with the flow of gas / air into the burner. The opening into the burner
directly in front of the gas valve should be checked regularly and cleared with a pipe cleaner or
similar length device.
Do not attempt to repair the burner yourself.
Slim Cooker Installation & Operating Instructions
FOR YOUR SAFETY – WHAT TO DO IF YOU SMELL GAS
Turn off gas supply at bottle immediately and extinguish all naked flames.
Remove the appliance from any potential ignition sources and do not operate any electrical equipment near the
appliance (e.g.: light switches, power points, mobile phones, pagers, other appliances)
Allow sufficient time for any accumulated propane gas to disperse
Check for damage to seals and hoses and if no damage is visible, ensure fittings are adequately tight then
check for gas leaks using soapy water as detailed in this manual in a well ventilated area. Do not try to detect
leaks using a flame
If odour / gas leak persists, turn off the gas supply at the gas cylinder and contact an authorized service agent.
HOW TO CHECK FOR GAS LEAKS
To check for leaks, open the gas supply at the bottle with the appliance gas valves in the OFF position (DO
NOT SWITCH APPLIANCE ON) and check for leakage by brushing a solution of soapy detergent and water
onto the connection points at the bottle and the appliance. If bubbling is evident (it may take more than 30
seconds to appear) this indicates a gas leak is present. If disassembling, cleaning, reassembling and tightening
the connection does not rectify the leak you should close the gas cylinder valve and consult the place of
purchase for assistance.
Turn on the gas and check for gas leakage at all joints with soapy water or other approved methods.
PROCEDURES FOR GAS LEAKAGE
The strong and distinctive odour of gas may make you aware of a gas leak. If you suspect a gas leak:
Immediately turn off the gas supply at the gas bottle;
Turn off all appliances and pilot lights;
Do not allow gas to build up in the area.
Do not use any naked flame or other ignition source (such as light switches, power points, mobile phones and
pagers);
Do not operate any electrical equipment in the vicinity of a gas leak;
Contact your licensed gas fitter to repair the leak and re-light the appliance.
NEVER attempt to repair the appliance yourself.
IT MUST BE SERVICED AND REPAIRED BY A LICENSED PLUMBER OR GAS FITTER
PARTS INDEX
3012PG-B, 3012NG, S3012PG & 3012NG
7012PG-B, 7012NG, S7012PG & S7012NG
No: Part Name
1 Control Knob
2 Trivet
3 Tray
4 Gas Inlet
5 Inner Burner
6 Outer Burner
7 Leg
8 Body
9 Safety Device
(S3012PG, S3012NG, S7012PG
& S7012NG only)
Slim Cooker Installation & Operating Instructions
PREPARE TO ASSEMBLE THE APPLIANCE
Check for damage on the appliance. If damage occurs, please contact Austcrown or your dealer. Do not
use a damaged appliance.
WARNING! It is hazardous to use a damaged appliance.
Positioning the Appliance
Only use the appliance in well ventilated areas. The appliance must be sited with at least a 500 mm gap
between both sides and the rear of the appliance and at least 1 m from the trivet of the appliance and
any combustible or non-combustible materials above the appliance.
When the burner is assembled abutting a side or rear wall, the wall must be of non-combustible material,
e.g. ceramic tiles. If surrounding walls are constructed with a combustible material, contact your local
Gas Authority for information on clearances required.
The appliance must be secured to minimize movement and strain on the appliance connection.
The appliance must be used on a level, stable, non-flammable surface when in use. If used on the
ground in an area with long grass ensure that the grass is not long enough to enter under the appliance
or at the sides as this could result in the grass catching fire.
It is important that the ventilation openings of the appliance are not obstructed.
The appliance should be protected from direct draughts and be positioned or protected against direct
penetration by any trickling water (e.g. rain).
Gas Type and Gas Pressure
Do not use any other gas type except the one specified on the label/data plate.
For LP Gas Model
These models of appliances are only suitable for use with propane gas only and are set to operate under
gas pressure of 2.75kPa.
For Natural Gas Model
These models of appliances are only suitable for use with natural gas only and are set to operate under
gas pressure of 1.00kPa.
The use of any equivalent Australia Approved hose/regulator assembly compliant with the above requirements
is acceptable.
WARNING! It may hazardous to attempt to use other types of gas with this appliance.
Gas Cylinder (For LP Gas Model only)
Only cylinders which comply with AS2030.1 should be used. The appliance is suitable for use with gas
cylinders of 3.9 kg to 15 kg gas capacity.
The gas cylinder should not be dropped or handled roughly! If the stove is not in use, the cylinder must
be disconnected. Replace the protective cap on the cylinder after disconnecting the cylinder from the
stove.
WARNING! It may hazardous to use damaged or dented gas cylinder.
Cylinders must be stored outdoors in an upright position and out of the reach of children. The cylinder
must never be stored under direct sunlight or where temperatures can reach over 50C. Do not store the
cylinder near flames, pilot lights or other sources of ignition. DO NOT SMOKE around the cylinders.
WARNING! It may hazardous to store gas cylinder in an enclosed place.
Hose
Use only gas hose complies with AS/NZS1869. The appliance required a ‘Class C’ Gas hose, with a ¼”
BSPF threaded swivel nut with 60º inverted flare connected to the gas inlet of the appliance. The hose should be
secured to the regulator and the appliance with spanner. Use the hose with the right threads, DO NOT
use adaptors.
WARNING! It may hazardous to use wrong type of hose.
The life expectancy of the hose is estimated as 5 years. It is recommended that it the hose is changed
every 5 years.
Slim Cooker Installation & Operating Instructions
The use of the wrong hose is unsafe; always check that you have the correct items before operating the
stove.
The hose used must conform to the relevant standard for the country of use. The length of the hose
must not excess 1.5 metres (maximum). A worn or damaged hose must be replaced. Ensure that the
hose is not obstructed, kinked, or in contact with any part of the stove other than at its connection.
WARNING! It may hazardous to use a damaged hose.
Regulator
Use only an approved regulator. The appliance must be used with a LOW pressure regulator with output
pressure of 2.75kPa for Propane Gas Model or 1.0kPa for Natural Gas Model. Use the regulator with the
right threads. DO NOT use adaptors.
The use of any equivalent certified hose/regulator assembly compliant with the above requirements is acceptable.
WARNING! It may hazardous to use wrong type of regulator.
Storage of Appliance
Always wait for the appliance to cool down before attempting to transport or store. Storage of a stove for
transport or indoors is only permissible if the cylinder is disconnected and removed from the appliance.
When the appliance is not to be used for a period of time it should be stored in its original packaging and
stored in a dry dust free environment.
ASSEMBLY INSTRUCTIONS
The manufacturer and their appointed agents decline any responsibility in the case of assembly not being in
accordance with these instructions. You will require a Philips head screwdriver and adjustable wrench for
assembly purposes and you should also refer to exploded view / parts list as necessary.
CAUTIONS
The burner must be installed only by a licensed gas fitter/plumber.
Do not install a damaged burner. Contact your service agent or the supplier.
Check the gas type of the burner and make sure the burner is connected to the gas type specified on
the data plate.
Before connection, ensure that there is no debris caught in the head of the gas cylinder, hose, burner
and burner ports.
Please always ensure that adequate fresh air ventilation is provided.
The burner must only be used on a level firm non-combustible surface.
The use of an adjustable wrench is required.
CLEARANCES
This cooker must be placed so that a vertical clearance of at least 600mm is maintained between its burners
and any combustible material. Where it is not practical, the underside of any combustible material with a
vertical clearance of less than 600mm above a burner should be protected by mill-board at least 6mm thick
which is covered with sheet metal not less than 0.4mm thick, or protected by an equivalent material extending
at least 225mm beyond the sides of the cooker. In either case, the vertical clearance above the cooker burner
should not be less than 450mm.
The minimum clearance from the cooker to rear or sides of combustible surfaces must be no less than 225mm.
When the cooker is installed abutting a side or rear wall, the wall must be of non-combustible material, e.g.
ceramic tiles. If surrounding walls are constructed with a combustible material, contact your local Gas Authority
for information on clearances required.
Combustible material Ran
g
e hood
Slim Cooker Installation & Operating Instructions
LPG INSTALLATION
1. Remove all packing material and literature from the cooker.
2. Remove the plastic laminate film off the top surface of the cooker.
3. The hose assembly should not be assembled beneath the cooker, under direct sunlight and close to other
sources of heat.
4. Gas inlet fitting located at the rear of the cooker: ¼ ” BSPM 60o
coned
5. Ensure that the gas supply connection point is accessible when
the cooker is installed.
6. Wrap Teflon Tape around all male threads as follows:
Start wrapping the male threads at end of the pipe but do
not lap over the end. Doing so may result in reduced gas
pressure or even blockages from bits of the tape that get into the gas supply.
Start with a couple loops around at the end, then wrap all the threads, overlapping half the width of the tape
on each wind. Wrap in the direction of the threads starting from the end and proceeding toward the length
of the pipe.
Wrapping the wrong way may result in the tape coming unwound as the fittings are tightened.
As you wrap, keep tension on the tape so that it is pulled into the threads. If you loosen or disconnect a
fitting, remove the old tape and rewrap with a fresh piece.
7. Connecting the hose and regulator assembly:
The outlet connection fitting of the hose assembly required is ¼” BSP Female threaded swivel nut with 60o
inverted flare. Screw the outlet end of the hose assembly onto the teflon tape wrapped-inlet at the rear of
the cooker and tighten using a suitable wrench.
8. Connect the regulator end of the gas supply hose to the LPG cylinder and tighten the connection fully in a
counter-clockwise direction.
9. THE GAS CYLINDER MUST BE INSTALLED OUTDOORS AT ALL TIMES
NATURAL GAS INSTALLATION
Natural gas installation must be carried out by a licensed plumber and must be in accordance with AS5601
1. Check for gas leakage at all joints with soapy water or other approved methods.
2. For natural gas connect the regulator to the ¼”BSPM inlet connection of the cooker, to ensure gas tight, Teflon
tape is required. Inlet of the hose must be connected to a bayonet socket. This must be done by a licence
plumber.
3. For gas plumbers, gas leak must be checked before leaving.
CAUTION: CHECK GAS LEAK BY SOAPY WATER, NEVER USE A NAKED FLAME.
OPERATING INSTRUCTIONS
USING THE COOKER
Follow these steps when operating the cooker:
LIGHTING THE COOKER
1. Make sure the ignition knob is set to the ‘OFF’ position.
2. Press in and turn the ignition knob counter-clockwise until a “click” sound is
heard. Make sure the burner has been lit properly.
3. Repeat Step 1 to 2, until burner is alighted.
4. Keep press and hold for 10 seconds, then release.
5. Repeat Step 1 to 4, if the burner fails to ignite.
ADJUSTING THE AIR FLOW:
To achieve an efficient, rigorous blue flame, the proper mixture ratio of air (oxygen)
and gas must be made prior to combustion. This can be adjusted by altering the
amount of air (oxygen) entering the burner via an adjustable shutter plate at the
venturi (or tail) end of the burner.
1. After the gas has been ignited, adjust the aeration shutter under the cooker until
slightly rounded and vigorous blue flames are produced.
2. The aeration shutter is located directly under the ignition knob.
ADJUSTING THE FLAME
Rotate the knob to achieve high or low flame you required.
Slim Cooker Installation & Operating Instructions
SHUTTING DOWN THE COOKER
1. Turn the LP cylinder gas valve fully clockwise to “OFF” position. When the
appliance is not in use/stored, the gas must always be turned off at the
cylinder to ensure there is no gas flow and that no gas is present in the
regulator, hose and appliance.
2. Turn the ignition knob to the OFF position until a “click” sound is heard.
Make sure there is no flow of gas through the burner.
RESTART COOKER AFTER FLAME FAILURE SAFETY DEVICE
ACTIVATED
If case the burner flame accidentally extinguished. The flame failure safety device will be set off and cut off the gas
supply to the burner head to prevent gas leakage. To restart the cooker, please follow the procedures below
1. Turn off the cooker.
2. Wait for 5 minutes.
3. Re-ignite the cooker (See Section “LIGHTING THE COOKER”).
CAUTION
Turning off the cooker
Slim Cooker Installation & Operating Instructions
MAINTENANCE
Allow the cooker to cool after use before performing any cleaning or maintenance work. Do not move the
appliance or attempt any maintenance within 30 minutes of cooker being used.
Burner ports may be cleaned with either compressed air or pipe cleaner or similar device.
Any spider’s web formed in the burner inlet (venturi) must be cleared with a pipe cleaner or similar length
device. Caution: Operation of the burner with a web in the inlet may result in leakage and/or ignition of gas at
the burner inlet.
It is also recommended that the hose assembly and regulator inlet fitting seals be checked for damage,
abrasion, cracking or displacement before each use. PVC hose assemblies may harden with age and should
be replaced if this occurs. If a replacement part or assembly is required please contact place of purchase or an
authorised agent for advice.
Periodic service should be performed at intervals not exceeding 6 months by an authorised service agent or
more often if required
Keep the cooker clean regularly by wiping with a damp cloth.
Before checking and maintaining the cooker, make sure the main gas valve is turned off.
Make sure the burner head(s) is/are clean before using the cooker. Use a steel wire brush to clean the burner if
it is heavily clogged. If the burner is heavily clogged, do not use the unit. Contact your authorised plumber or
gas fitter to carry for cleaning and maintenance. Do not attempt to remove the burner unit(s) yourself.
Check the gas pipes regularly for wear or leaks. If any wear or leaks are presents, please contact an
authorised plumber / gasfitter for repair.
Do not touch the burner, trivet, tray etc. immediately after use or when in use. This could burn your hand.
Clean the trivet and tray after each use. Always wipe off spills, do not leave spills to dry on the surface of the
trivet, tray or burner.
Inspect the electrodes carefully after you have removed the tray receptacle and if soiled, clean with a dry cloth.
ABNORMAL OPERATION
You should cease using the appliance and seek service from an authorised agent if any of the following are
observed during operation of the appliance:
Carbon build up on the appliance or pans,
Excessive yellow tipping of the burner flame,
Flames lifting off the burner ports or flashing back.
Flame abnormality may be due to gas supply restriction or blockage of burner ports or venturi. Gas spillage may
occur if the burner inlet is partially blocked by a spider’s web, the gas may ignite around the burner inlet.
It is recommended that an authorised person/service agent perform all maintenance.
If the cooker fails to operate correctly, contact place of purchase or authorised agent for advice and service.
DO NOT ATTEMPT REPAIRS YOURSELF.
CONVERSION
These cookers are not convertible; they must be used with the gas specified.
Slim Cooker Installation & Operating Instructions
SPECIFICATION TABLE
Product images
Model S7012NG S7012PG 7012NG 7012PG-B S3012NG S3012PG 3012NG 3012PG-B
Gas type Natural propane Natural propane Natural propane Natural propane
Outer Ring 12.00MJ/hr 9.10MJ/hr 12.00MJ/hr 9.10MJ/hr 12.00MJ/hr 9.10MJ/hr 12.00MJ/hr 9.10MJ/hr
Inner Ring 2.60MJ/hr 2.30MJ/hr 2.60MJ/hr 2.30MJ/hr 2.60MJ/hr 2.30MJ/hr 2.60MJ/hr 2.30MJ/hr
Heat
Capacity Total 29.20MJ/hr 22.80MJ/hr 29.20MJ/hr 22.80MJ/hr 14.60MJ/hr 11.40MJ/hr 14.60MJ/hr 11.40MJ/hr
Outer Ring 0.27m3/hr 0.21Kg/hr 0.27m3/hr 0.21Kg/hr 0.27m3/hr 0.21Kg/hr 0.27m3/hr 0.21Kg/hr
Inner Ring 0.05m3/hr 0.04Kg/hr 0.05m3/hr 0.04Kg/hr 0.05m3/hr 0.04Kg/hr 0.05m3/hr 0.04Kg/hr
Gas
Cnsmptn Total 0.64m3/hr 0.50Kg/hr 0.64m3/hr 0.50Kg/hr 0.32m3/hr 0.25Kg/hr 0.32m3/hr 0.25Kg/hr
Outer Ring 1.25mm 0.80mm 1.25mm 0.80mm 1.25mm 0.80mm 1.25mm 0.80mm
Inner Ring 0.60mm 0.40mm 0.60mm 0.40mm 0.60mm 0.40mm 0.60mm 0.40mm
Injector
Size Pilot 0.65mm 0.45mm 0.65mm 0.45mm 0.65mm 0.45mm 0.65mm 0.45mm
Burner size 120mm 120mm 120mm 120mm 120mm 120mm 120mm 120mm
Gas pressure 1.0kpa 2.75kpa 1.0kpa 2.75kpa 1.0kpa 2.75kpa 1.0kpa 2.75kpa
Safety Device YES YES N/A N/A YES YES N/A N/A
Net weight 6.06kg 5.76kg 3.18kg 3.12kg 3.00kg
Dimensions W×D×H 690mm*380mm*109mm 280mm*380mm*109mm
Ignition system Auto Piezo Electric Ignition
Gas fitting 1/4" BSPM 60°conned
SAI Global Approval No. GSCS20074
Country of origin China
Austcrown Pty. Ltd and their appointed agents will not be liable in respect of any misuse, which is not in
accordance with the instructions and precautions specified in this booklet.
TROUBLESHOOTING
Problem Possible Cause Solution
No Ignition
Main Gas Valve is not turned on.
Air trapped in the gas hose.
Electronic ignition is wet or dirty.
The safety valve is not open.
Turn off the gas valve once and then turn it on fully.
Repeat the ignition process until all air in the hose is purged completely.
Clean and wipe the electrode with a dry cloth.
Push in the ignition knob and turn it anti-clockwise until a click sound is heard. Ensure the
burner has been lit. Press the ignition knob for 3-4 seconds and release the knob.
Gas Leaking Failure of the gas valve. Contact your dealer for a service/repair.
DO NOT ATTEMPT TO REPAIR IT YOURSELF.
Incomplete
Combustion
(Yellow Flame)
Aeration shutters are not properly
adjusted.
Burner is not properly assembled.
Flame holes of the burner are clogged.
Nozzle is clogged.
Follow procedures for Adjusting the Airflow
Position the burner body properly.
Clean the burner head and the burner cap.
Contact your dealer for a service/repair.
DO NOT ATTEMPT TO REPAIR IT YOURSELF.
Slim Cooker Installation & Operating Instructions
AUSTCROWN PTY LTD
18 / 634 Mitcham Road, VERMONT VIC 3133, AUSTRALIA
Fax: +61 3 9873 5311
Email: [email protected] Web: www.auscrown.com
SERVICE AGENTS
For services and repairs, contact our service agent or any other authorised gas fitter and plumber.
Progress Plumbing and Gas Maintenance
16 Raymond Street, BLACKBURN VIC 3130
Ph: 9878 5845 Mobile: 0418 379 252
AUSCROWN
www.auscrown.com
- Natural Gas or LP gas - Stainless Steel Body
- Piezo Ignition - Pans & Pots Compatible
- Indoor or Outdoor Use - BBQ Side Burner
- Alfresco Cooking - Adjustable Double Ring Flame
AUSCROWN
WITH
BEEHIVE
BURNER
CK107LP/RB18NG CK203LP/RB28NG
CK801NG RB18NG CK801PG CK107LP CK802NG RB28NG CK802PG CK203LP
15.8MJ/hr 14.2MJ/hr 13.5MJ/hr 12.5MJ/hr 2 x 15.8MJ/hr 2 x 14.2MJ/hr 2 x 13.5MJ/hr 2 x 12.5MJ/hr
Outer Ring Ø0.95mm Ø0.90mm Ø0.95mm Ø0.90mm
Inner Ring Ø0.45mm Ø0.40mm Ø0.45mm Ø0.40mm
Pilot
2.75kPa 1.0kPa 2.75kPa
Ø0.90mm Ø0.50mm Ø0.90mm Ø0.50mm
Piezo-Electric
1/4" BSPM 60º Coned
7092
China
W292mmxD382mmxH145mm
3.41kg W720mmxD382mmxH145mm
6.53kg
Dimensions
Natural Gas Propane Gas Propane Gas
1.0kPa
Ø1.65mm
Ø0.7mm
Natural Gas
Ø0.7mm
Ø1.65mm
Inlet Fitting
Country Of Origin
Model
Heat Capacity
AGA Approval No
Net Weight
Ignition System
Gas Type
Gas Pressure
Injector Size
CK801PG/NG CK802PG/NG
Outer Ring High
Inner Ring High Outer Ring Low
Inner Ring High Outer Ring Low
Inner Ring Low Outer Ring Off
Inner Ring High Outer Ring Off
Inner Ring Low
WITH
BRASS CAP
BURNER
METAL TROLLEY FOR
SINGLE WOK BURNER COOKER DUST CAP FOR GAS CYLINDER VALVE
STEP 1 STEP 2 STEP 3 FINISH
Cap with
POL Male
Thread
Cap with
Female
Thread
Cap with
No
Thread
COOKER NOT
INCLUDED
COOKER NOT
INCLUDED
MTR18
S7012NG/S7012PG/7012PG
S3012NG/S3012PG/3012PG
Flame Failure
Safety Device
(S7012/S3012
Series Only)
Double Ring
Swirling Burner
with Swirl Flame
Specifications S7012NG S7012PG 7012PG S3012NG S3012PG 3012PG
YES YES N/A YES YES N/A
6.06kg 6.0kg 5.76kg 3.18kg 3.12kg 3.0kg
Natural Natural
1.0kPa 1.0kPa
2 x 14.6MJ/hr 14.6MJ/hr
2 x 0.32m³/hr 0.32m³/hr
Outer Ring Ø1.25mm Ø1.25mm
Inner Ring Ø0.60mm Ø0.60mm
Pilot Ø0.65mm Ø0.65mm
Model
Gas Type
Heat Capacity
Gas Consumption
Injector
Size
Safety Device
Net Weight Propane
2.75kPa
2 x 11.4MJ/hr
Propane
Dimensions W690mm x D380mm x H109mm W280mm x D380mm x H109mm
11.4MJ/hr
Gas Pressure
0.25kg/hr2 x 0.25kg/hr
Ø0.40mm
Ø0.45mm
Ignition System
2.75kPa
SAI Global Approval
Ø0.80mm
Ø0.40mm
Ø0.45mm
Ø0.80mm
GSCS20074
Piezo Electric
Inlet Fitting 1/4" BSPM 60º Coned
Model MTR18
Colour
Net Weight
Dimensions W1040mmxD470mmxH820mm
Black Powder Coated
8.0kg
Completed with Hose and Regulator
AUSCROWN
AUSCROWN Butane Gas HANDY RANGE
Features:
Portable / Piezo Ignition / Indoor or Outdoor / Light Weight / Easy to Use / Compact
Model AD90 HR200
Injector Size Ø0.55mm Ø0.56mm
Dimensions W343mm x D256mm x H111mm W335mm x D290mm x H88mm
AGA Approval No 5240 6860
Gas Type
Gas Pressure
Heat Capacity
Gas Consumption
Net Weight
Ignition System 1.7kg
150g/hr
7.0MJ/hr
Piezo-Electric
Butane Gas
Cartridge Pressure
Packing:
4 units/pack
Grill plate lifter included.
For convenient and safe
handling.
Removable non-stick
grill plate. Makes cooking
and cleaning easy.
Enamelled pan.
Collects excessive grease
and reduces smoke
How it works
* Handy Range Not Included.
230GM
BUTANE GAS CARTRIDGE
GP33 KOREAN BBQ GRILL PLATE
HR200
AD90
Features:
- 33cm diameter.
- Removable non-stick grill plate.
- Steam function.
- Enameled pan.
- Grill plate lifter included.
Steam action.
Keeps food moist & succulent when cooking.
AUSCROWN BRUSHED STAINLESS STEEL
CANOPY RANGE HOODS
Features:
Strong Suction / Brushed Stainless Steel Body / 3 Speed Control /
Micromesh Filters /Optional Charcoal Filter / Ducted or Re-circulated Exhaust
CS900 900MM CS600 600MM
CI900G 900MM ISLAND TYPE
WITH TEMPERED GLASSCI900 900MM ISLAND TYPE
C900GH 900MM CANOPY
WITH TEMPERED GLASS
X: Heigh when duct cover fully extended.
Model C900GH CS900 CS600 CI900 CI900G
Dimensions
W900mm
D475mm
H579mm
X960mm
W900mm
D500mm
H582mm
X980mm
W600mm
D500mm
H580mm
X980mm
W895mm
D600mm
H637mm
X1204mm
W895mm
D600mm
H613mm
X1180mm
Net Weight 21kg 22kg 17kg 27kg 29kg
Lamp Power
Flow Rate
Load of Motor
Duct Size
C tick Approval
AS Approval
Power
No. of Motor
1000m³/hr
2 x 2W
150mm
4 x 2W
240V 60Hz
1
V06076/0
N2788
250W
PORTABLE FOR OUTDOOR USE WITH LP GAS BOTTLE
Rambo
Model HPA100LPB RH31LT HP200LPB
Dimensions W320mm x L520mm x H160mm W330mm x L490mm x H180mm W415mm x L690mm x H220mm
Net Weight 6.6kg 7.7kg 14.9kg
Injector Size Burner :Ø0.90mm
Pilot: Ø0.45mm Burner: Ø0.90mm
Pilot: Ø0.25mm
Outer Ring: Ø0.1.2mm
Inner Ring: Ø0.55mm
Pilot: Ø0.25mm
Ignition System Piezo Electric Manual with Pilot Manual with Pilot
Gas Pressure 61kPa
Heat Capacity 64MJ/hr
Gas Consumption 1.6kg/hr
Gas Type
Inlet Fitting 1/4" BSPM 60º Coned
Propane
55MJ/hr
100kPa
1.0kg/hr
COMPLETE WITH HOSE & REGULATOR
WITH AUTOMATIC IGNITION
Low Pressure
COMPLETE WITH HOSE & REGULATOR
RBC176LP RBC225LP
20MJ/hr 32MJ/hr
0.42kg/hr 0.64kg/hr
Inner Ring Ø0.65mm Ø0.90mm
Outer
Ring Ø1.20mm Ø1.30mm
Pilot Ø0.60mm Ø0.6mm
W320mm x D520mm x H160mm W320mm x D480mm x H180mm
5.16kg 6.6kg
Inlet Fitting 1/4" BSPM 60º Coned
Country of Origin China
Approval No. IAPMO R&T OCEANA GMK10042
Net Weight
Dimensions
Injector
Size
Gas Consumption
Model
Gas Pressure
Heat Capacity
ULP gas
2.75kPa
Gas Type
Ignition System Piezo Electric
RH31LT with pilot HP200LPB 2 ring high with pilot HPA100LPB with auto ignition
FOR OVERSEAS MARKET ONLY FOR OVERSEAS MARKET ONLY
RH31LT & HP200LPB
for overseas only
not for Australia
AUSCROWN LOW PRESSURE
CAST IRON RING BURNER
Features:
High Heat Capacity / Portable / Ideal for Outdoor Cooking / Individual Ring Control
*Burners Not Included
FRAME FOR CAST IRON RING BURNER
Features:
Portable / Ideal for Stockpot Cooking
FF30 FOR C30LP
FF40 FOR C40LP
FF50 FOR C50LP
Rings can be operated individually
C20LP C30LP C40LP C50LP
Model C20LP C30LP C40LP C50LP
Number of Rings 1 2 3 4
Heat Capacity 12MJ/hr 20MJ/hr 30MJ/hr 59MJ/hr
Gas Consumption 0.26kg/hr 0.44kg/hr 0.65kg/hr 1.28kg/hr
Injector Size Ø1.0mm 1st Ring: Ø0.7mm
2nd Ring: Ø1.1mm
1st Ring: Ø0.50mm
2nd Ring: Ø0.90mm
3rd Ring: Ø1.20mm
1st Ring: Ø0.50mm
2nd Ring: Ø0.80mm
3rd Ring: Ø1.05mm
4th Ring: Ø1.50mm
Dimensions W190mm
L370mm
H85mm
W185mm
L420mm
H85mm
W250mm
L470mm
H95mm
W360mm
L635mm
H110mm
Net Weight 1.82kg 3.2kg 6.2kg 12.8kg
Gas Type
Gas Pressure
Ignition System
Inlet Fitting
AGA Approval No
Propane Gas
2.75kPa
Manual
1/4" BSPM 60º Coned
6429
Supplied with
AGA approved
regulator & 1.2 meter hose
FF30 FF40 FF50
W378mm x D378mm x H175mm W430mm x D430mm x H175mm W530mm x D530mm x H175mm
5.6kg 6.6kg 8.8kg
Ø458mm Ø510mm Ø610mm
Ø378mm Ø430mm Ø530mm
Model
Dimensions
Net Weight
Minimum Pot Size
Maximum Pot Size
FF30 FF50
AUSCROWN
GAS LIGHTERS
SL160
PIEZO ELECTRIC
IGNITOR
JZDD17
PIEZO ELECTRIC
IGNITOR
RBA2 CAST IRON BBQ LONG BURNER
Overall Length: 40.5cm
Burner Length: 35cm
Burner Width: 7.8cm
Inlet Size: Ø1.3cm
N.W.: 1.9kg
GM28 BUTANE GAS MATCH
WITH CHILD SAFETY LOCK
Ideal for Manual Ignition Gas Appliances
RBA2 CAST IRON BBQ LONG BURNER
Ring Burner Country Cooker
CAST IRON LOW PRESSURE COUNTRY COOKER
GB01LP 1 burner GB02LP 2 burners GB03LP 3 burners
FOR OUTDOOR USE ONLY
Features: Portable / Ideal for Outdoor Cooking / Double Ring Burner
Specifications
Supplied with Hose and Regulator
Features: Portable / Ideal for Outdoor Cooking / Double Ring Burner
GB03LP 3 burners
JZDD17
PIEZO ELECTRIC
IGNIT
OR
Model GB01LP GB02LP GB03LP
Heat Capacity 12MJ/hr 2 x 12MJ/hr 3 x 12MJ/hr
Gas Consumption 0.26kg/hr 2 x 0.26kg/hr 3 x 0.26kg/hr
Dimensions (mm) W270 x D350x H140 W520 x D350 x H140 W770 x D350 x H140
Net Weight 3.20kg 5.5kg 8.7kg
Gas Type
Gas Pressure
Injector Size
Ignition System
Gas Inlet Fitting
AGA Approval No
Country of Origin
1/4" BSPM 60º Coned
Propane Gas
2.75kPa
6327
China
Ø1.0mm
Manual
AUSCROWN
28 Jet Flame 18 Jet Flame
Y018LPWF
LOW PRESSURE DUCKBILL STOCKPOT BURNERS
LP gas models supplied with hose and regulator
Natural gas models supplied with regulator
Heat/boil 100 to 200 litre pot
HIGH PRESSURE STOCKPOT BURNERS
FOR OUTDOOR USE ONLY
FOR OUTDOOR USE ONL
Y
FOR OUTDOOR USE ONLYFOR OUTDOOR USE ONL
HP200LPWF
double ring
HPA100LPWF
single ring with
auto ignition
HIGH PRESSURE STOCKPOT BURNERS
HP
single ring with
auto ignition
Y018LPWF Y018NGWF Y028LPWF Y028NGWF
Propane Gas Natural Gas Propane Gas Natural Gas
2.75kPa 1.0kPa 2.75kPa 1.0kPa
67MJ/hr 67MJ/hr 104MJ/hr 104MJ/hr
1.34kg/hr 1.76m³/hr 2.08kg/hr 2.74m³/hr
Duckbill jet Ø0.55mm Ø1.05mm Ø0.55mm Ø1.05mm
Pilot Ø0.40mm Ø0.80mm Ø0.40mm Ø0.80mm
18 28
Manual with Pilot
1/2" BSPF
China
44kg
W490 x D570 x H410
27kg
Min: Ø440 Max: Ø490
GASMARK CERTIFICATE GMK10005
W610 x D690 x H490
Min: Ø440 Max: Ø610
Pot Size (mm)
Net Weight
Ignition System
Inlet Fitting
Approval No
Country of Origin
Model
Gas Type
Gas Pressure
Heat Capacity
Gas Consumption
Dimensions (mm)
Injector
SizeNo. of jets
Y018LPWF
with Flame Failure Safety Device
Flame Failure
Safety Device
HP200LPWF for overseas only, not for Australia
Model HP200LPWF HPA100LPWF
Gas Pressure 61kPa 100kPa
Heat Capacity 64MJ/hr 49MJ/hr
Gas Consumption 1.6kg/hr 1.0kg/hr
Ignition System Manual Pilot Piezo Electric
Injector Size Outer Ring: Ø1.20mm
Inner Ring: Ø0.55mm
Pilot: Ø0.25mm
Burner: Ø0.90mm
Pilot: Ø0.45mm
Dimensions (mm) W456 x D760 x H440 W456 x D600 x H440
Net Weight 33kg 29kg
Approval No For overseas only IAPMO GMK10051
Gas Type
Inlet Fitting
Pot Size
country of Origin Min: Ø400mm Max: Ø610mm
Propane Gas
1/4" BSPM 60º coned
China
AUSCROWN
TYPE B / SECOND TIER APPROVAL FROM A LICENSED GAS INSPECTOR MUST BE OBTAINED PRIOR TO OPERATION
A30NG
and A30LP
A30NG
and
A30LP
LOW PRESSURE CAST IRON MUSHROOM BURNER
A7NG and A7LP A12NG and A12LP
A7NG and
A7LP
A12NG and
A12LP
A16NG and A16LP
LP gas models supplied with hose and regulator
Natural gas models supplied with regulator
Heat/boil 100 to 200 litre pot
Product Name
Model A07LP A07NG A12LP A12NG A16LP A16NG A30LP A30NG
Gas Type Propane Gas Natural Gas Propane Gas Natural Gas Propane Gas Natural Gas Propane Gas Natural Gas
Gas Pressure 2.75kPa 1.0kPa 2.75kPa 1.0kPa 2.75kPa 1.0kPa 2.75kPa 1.0kPa
Heat Capacity 25.1MJ/hr 33.7MJ/hr 47.4MJ/hr 57.8MJ/hr 58.9MJ/hr 77.0MJ/hr 118.2MJ/hr 144.5MJ/hr
Gas Consumption 0.5kg/hr 0.88m³/hr 0.95kg/hr 1.52m³/hr 1.18kg/hr 2.03m³/hr 2.37kg/hr 3.81m³/hr
Nozzle Size Ø0.58mm Ø1.10mm Ø0.58mm Ø1.10mm Ø0.58mm Ø1.10mm Ø0.58mm Ø1.10mm
Dimensions (mm)
Net Weight
Ignition System
Flame Failure Safety
Inlet Fitting
Country of Origin Taiwan
1/4" BSPM 60º coned
Mushroom stockpot burnerMushroom burner
Manual Pilot
YesNo
W265 x L490 x H180 W300 x L540 x H210 W370 x L570 x H220
1/2" BSPM
Piezo Electric
W430 x L720 x H300
6kg 8.5kg 14kg 32kg
All Rings On
Outer Ring OnInner Ring On
All Rings On
Outer Ring OnInner Ring On
Specifications
With Flame Failure Safety Device
and Manual Pilot Ignition
A16NG and
A16LP
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
