Job Name:
Schedule Reference: Date:
Specications are subject to change without notice.
© 2014 Mitsubishi Electric US, Inc.
Specications System Module 1 Module 2
Unit Type PURY-P192YSKMU-A (-BS) PURY-P96YKMU-A (-BS) PURY-P96YKMU-A (-BS)
Nominal Cooling Capacity (460V) Btu/h 192,000 96,000 96,000
Nominal Heating Capacity (460V) Btu/h 215,000 108,000 108,000
Operating Temperature Range *1 Cooling (Outdoor) *2 Refer to Module Data 23~115° F (-5~46° C) DB
Heating (Outdoor) -4~60° F (-20~15.5° C) WB
External Dimensions (H x W x D) In.
mm Refer to Module Data 64-31/32 x 48-1/16 x 29-5/32
1,650 x 1,220 x 740
64-31/32 x 48-1/16 x 29-5/32
1,650 x 1,220 x 740
Net Weight Lbs. / kg 1,148 (520) 574 (260) 574 (260)
External Finish Refer to Module Data Pre-coated galvanized steel sheet
Electrical Power Requirements Voltage, Phase, Hertz Refer to Module Data** 460V, 3-Phase, 60Hz
Minimum Circuit Ampacity (MCA) A Refer to Module Data** 15 15
Maximum Fuse Size ARefer to Module Data** 20 20
Piping Diameter
F r o m T w i n n i n g K i t t o I n d o o r U n i t s
(Brazed) (In. / mm)
Liquid (High Pressure) 7/8 (22.2) Brazed Refer to System Data
Gas (Low Pressure) 1-1/8 (28.58) Brazed
Max. Total Refrigerant Line Length Ft. 2,461
Refer to System Data
Max. Refrigerant Line Length
(Between ODU & IDU) Ft. 541
Max. Control Wiring Length Ft. 1,650
Indoor Unit Total Capacity 50~150% of ODUs Refer to System Data
Model / Quantity P06~P96/1~48 Refer to System Data
Sound Pressure Level dB(A) 61 Refer to System Data
Fan
Type x Quantity Refer to Module Data Propeller fan x 1 Propeller fan x 1
Airow Rate CFM 6,200 6,200
External Static Pressure In. WG (Pa) Refer to Module Data Selectable; 0, 0.12 or 0.24”WG; factory set to 0”W.G.
Compressor Operating Range 8% to 100% Refer to System Data
Compressor Type x Quantity Refer to Module Data Inverter-driven Scroll
Hermetic x 1
Inverter-driven Scroll
Hermetic x 1
Refrigerant Refer to Module Data R410A x 26 lbs + 1 oz
(11.8 kg)
R410A x 26 lbs + 1 oz
(11.8 kg)
Protection Devices
High Pressure
Refer to Module Data
High pressure sensor, High
pressure switch at 4.15 MPa
(601 psi)
High pressure sensor, High
pressure switch at 4.15 MPa
(601 psi)
Inverter Circuit
(Comp. / Fan) Over-current protection Over-current protection
Fan Motor Thermal switch Thermal switch
AHRI Ratings
(Ducted/Non-Ducted)
EER 11.6 / 11.9
Refer to System DataIEER 19.3 / 18.2
COP 3.64 / 3.47
Simultaneous Rating
(Ducted/Non-Ducted) SCHE *3 17.40 / 21.81 Refer to System Data
Blue Fin Anti-corrosion Protection: Cellulose- and polyurethane-resin coating treatment applied to condenser coil that protects it from air contaminants
Standard: ≥1μm thick; Salt Spray Test Method - no unusual rust development to 480 hours.
Sea Coast (BS): ≥1μm thick; Salt Spray Test Method - no unusual rust development to 960 hours.
Outdoor Unit: 16-TON PURY-P192YSKMU-A (-BS)
(Consists of Two PURY-P96YKMU-A (-BS) and One CMY-R100CBK2 Twinning Kit)
UNIT OPTION
□Standard Model……..….........…...………….PURY-P192YSKMU-A
□Sea Coast (BS) Model………....……….PURY-P192YSKMU-A-BS
OUTDOOR VRF HEAT PUMP WITH HEAT RECOVERY
SYSTEM FEATURES
• INVERTER-driven compressor
• Air-source, simultaneous cooling and heating
• Long line lengths - for details see Engineering Manual
• Connects to CITY MULTI indoor units
• Controlled via CITY MULTI Controls Network
NOTES:
*1. Harsh weather environments may demand performance enhancing equipment.
Ask your Mitsubishi Electric representative for more details about your region.
*2. For details on extended cooling operation range down to -10° F DB, see Low Ambient Kit Submittal.
*3. Simultaneous Cooling and Heating Efciency
** Each individual module requires a separate electrical connection.
Refer to electrical data for each individual module.
OPTIONAL PARTS
□Twinning Kit (required)..............................................…CMY-R100CBK2
□Joint Kit.............................…for details see Pipe Accesories Submittal
□Joint Adapter Kit................…for details see Pipe Accesories Submittal
□Low Ambient Kit ...............…..for details see Low Ambient Kit Submittal
□Snow/Hail Guards Kit......…for details see Snow/Hail Guards Kit Submittal
Specications are subject to change without notice.
© 2014 Mitsubishi Electric US, Inc.
Outdoor Unit: PURY-P192YSKMU-A (-BS) – DIMENSIONS
Note 1.Connect the pipes as shown in the figure above. Refer to the table above for the pipe size.
2.Twinning pipe (High pressure) should not be tilted more than 15 degrees from the horizontal plane.
Be sure to see the Installation Manual for details of Twinning pipe installation.
3.The pipe section before the Twinning pipe (section "a" in the figure) must have at least 500mm(19-11/16) of straight section
(*including the straight pipe that is supplied with the Twinning pipe).
4.Only use the Twinning pipe by Mitsubishi (optional parts).
5.Connect the outdoor unit 1 with the Twinning pipe (Low pressure) (section "d" in the figure).
ø22.2(7/8)
P168P144
--
(Note 5)(Note 5)
P72P72P72
Twinning Kit
~Outdoor unit
P96
High pressure
ffdd
eeccø19.05(3/4)
Component
unit model
Unit model
Low pressure ø19.05(3/4)ø19.05(3/4)
ø15.88(5/8)ø15.88(5/8)ø15.88(5/8) ø19.05(3/4)
P9
6P
96
P192
-
(Note 5)
fd
ec ø19.05(3/4)
Low pressure
Twinning pipe connection size
Outdoor unit 1
Component unit name
Package unit name
BC controller~Twinning pipe a
b
High pressure
Outdoor Twinning Kit(optional parts) CMY-R100CBK2
Outdoor unit 2
PURY-P144YSKMU-A(-BS) PURY-P168YSKMU-A(-BS) PURY-P192YSKMU-A(-BS)
PURY-P72YKMU-A(-BS) PURY-P96YKMU-A(-BS) PURY-P96YKMU-A(-BS)
PURY-P72YKMU-A(-BS) PURY-P72YKMU-A(-BS) PURY-P96YKMU-A(-BS)
ø28.58(1-1/8)
ø22.2(7/8)
Front view
Left view
Outdoor unit 2Outdoor unit 1
To BC controller
To BC controller
a
b
e
f
c
d
Twinning pipe(High pressure)
<optional parts>
Twinning pipe(Low pressure)
<optional parts>
Intake
air
Intake
air
Discharge air
Intake
air
30(1-3/16)
1220(48-1/16) 1220(48-1/16)
1650(64-31/32)
740(29-5/32)
PURY-P144,168,192YSKMU-A(-BS)
Unit : mm(in.)
Specications are subject to change without notice.
© 2014 Mitsubishi Electric US, Inc.
Model: PURY-P96YKMU-A (-BS) – DIMENSIONS
(1)
(1)
(1)
(1)
(3/4)
(7/8)
(5/8)
(3/4)
(1-25/32)
(2-9/16)
(1-3/4)
(2-15/32)
(7/8)
(1-3/8)
(1-11/32)
(2-1/16)
(3-23/32)(5-29/32)
(3-1/16)(5-17/32)
Note 1.Please refer to the engineering manual for information
regarding necessary spacing around the unit and
foundation work. Outdoor unit must be mounted
at least 12" off the ground or 12" above the highest
average snow depth, whichever is greater.
2.At brazing of pipes,wrap the refrigerant service valve
with wet cloth and keep the temperature of
refrigerant service valve under 120°C(248°F).
Connecting pipe specifications
Refrigerant service
valve <High pressure>
Refrigerant service valve
<High pressure>
Refrigerant service
valve <Low pressure>
Refrigerant service valve
<Low pressure>
(5-3/4)
(5-3/4)
Transformer box
(1-3/16)
(1-3/16) (Mounting pitch)
(26-13/16)
(Mounting pitch)
(3-5/32) (3-5/32)
(4-25/32)
(8-9/16)
(5-23/32)
(10-11/32)
(7-23/32)
(3-5/16)
(3-23/32)
(10-23/32)
(11-7/8)
(8-15/16)
(2-1/4)
(2-1/4)
(13/16)(13/16)
(3-17/32) (3-1/16)
1
(9-29/32)
(9-5/16)
(10-23/32)
(11-15/16)
(25/32)
(25/32)
(2-25/32) (23-5/8)
<Snow hood attachment hole>
4X5-ø4.6(3/16) Hole
(Make hole at the plastic fan guard
for snow hood attachment)
Intake
air
Discharge air
Control box
Intake
air
Service
panel
Intake
air
<Sling hole>
3
6
2
458
2X2-14(9/16)X20(13/16) Oval hole
2X2-80(3-5/32)X35(1-13/32) Oval hole
7
High
pressure
ø25.4
ø25.4
Low
pressure
Service valveRefrigerant pipe
Diameter
*1
*1
High
pressure
Low
pressure
Model
PURY-P96YKMU
PURY-P72YKMU
ø25.4
ø25.4
ø19.05 Brazed
ø22.2 Brazed
ø15.88 Brazed
ø19.05 Brazed
*1
*1
(Uses when twinning
kit (optional
parts) is mounted.)
ø45 Knockout hole
Specifications
ø43.7 or ø22.2 Knockout hole
ø62.7 or ø34.5 Knockout hole
Front through hole
Bottom through hole
Bottom through hole
Front through hole
Front through hole
For wires
Usage
NO.
Front through hole
Front through hole
140 × 77 Knockout hole
150 × 94 Knockout hole
Bottom through hole
For pipes
ø52 Knockout hole
For transmission cables
ø34 Knockout hole
ø65 Knockout hole
*1 Use the pipe joint(field supply) and connect to the refrigerant service valve piping.
58(2-5/16)
75(2-31/32)
251
236
217
145
146
146
83(3-9/32)301
262
Bottom view
Left side view
Front view
Top view
(740)(29-5/32)
150(5-29/32)
272
57
29.5
54(2-5/32)
19.5
80
1060(41-3/4)
586(23-3/32)
19.5
57
94 84
121
227
600
20
1220(48-1/16)
150(5-29/32)
1650(64-31/32)
196
272
1347(53-1/16)
89
303
29.5
20
740(29-5/32)
70
1181(46-1/2)
140(5-17/32)
80
77
681
PURY-P72,96YKMU-A(-BS)
Unit : mm(in.)
1
2
4
5
6
7
8
3
1340 Satellite Boulevard
Suwanee, GA 30024
Toll Free: 800-433-4822
www.mehvac.com
Specications are subject to change without notice.
© 2014 Mitsubishi Electric US, Inc.
Twinning Kit: CMY-R100CBK2
Ref: CMY_R100VBK_EXD_EUDB_SI
<Deformed pipe(Accessory)>
<Low-pressure pipe twinning kit(Accessory)>
High-pressure twinning pipe
Low-pressure pipe twinning kit
<Deformed pipe(Accessory)>
<Pipe for routing through the bottom
(Accessory)>
<Pipe for routing through the front
(Accessory)>
<Elbow pipe(Accessory)>
1"
3/4"
3/4"
(Outside diameter) 1"
(Outside diameter)
(Outside diameter)
(3Pcs.)
(Outside diameter)
(Outside diameter)
(Outside diameter)
1”
1”
1”
7/8" 3/4"
5/8”
3/4”
3/4"
7/8”
1-5/32”
3/4”
7/8"
7/8"
7/8"
1-5/32"
1-5/32"
1-3/32”
1”
21/32"
8-7/16” 4-17/32"
2-5/16"
7-17/32"
3-5/32"
2-3/8”
3-17/32”
1-1/4”
4-5/32”
2-15/32"
3-5/32"
1-13/32”
5-1/4”
21/32”
6-15/16”
17-1/32”
2-15/32"
1-7/16”
1-7/16”
1-31/32"
1-31/32"
CMY-R100CBK2
Notes:
FORM# PURY-P192YSKMU-A (-BS) - 201407
/
