Audioplex IRB-4 Installation guide

Audioplex
Brand
Audioplex
Model
IRB-4
Type
Installation guide

Audioplex IRB-4 is an IR repeating systems termination block designed to work exclusively with Audioplex IR products. It features four 1/8" mono mini-jack emitter outputs, an unregulated +12vdc power supply, and an extra emitter jack that can accommodate up to four additional emitters using the Audioplex IRS-1. The IRB-4 allows for multiple IRTargets to be connected in parallel (up to 12) to the screw-down connector, eliminating the need for hard-wiring.

Audioplex IRB-4 is an IR repeating systems termination block designed to work exclusively with Audioplex IR products. It features four 1/8" mono mini-jack emitter outputs, an unregulated +12vdc power supply, and an extra emitter jack that can accommodate up to four additional emitters using the Audioplex IRS-1. The IRB-4 allows for multiple IRTargets to be connected in parallel (up to 12) to the screw-down connector, eliminating the need for hard-wiring.

DVD DOLBY DIGITAL
TECHNOLOGY
Termination block for IR repeating systems
INSTALLATION MANUAL
IRB-4
SPECIFICATIONS
INSTALLATION
Connectors: Screw-type
Emitter outputs: (4) 1/8" mono mini-jacks
Power supply: +12vdc unregulated power supply
Dimensions: 3.071"H x 1.654"W x .787"D
Extra Emitter Jack: Allows for an extra Emitter (or 4 extra emitters using the Audioplex IRS-1).
The IRB-4 provides a convenient connecting point for a remote relay system, eliminating hard-wiring.
Multiple IRTargets can be connected in parallel (up to 12) to the screw-down connector. We recommend
running 4-conductor "home-runs" from each room to the equipment stack and either connect directly to the
IRB-4 or use our IR-TB termination block as shown in the wiring diagram below. Each emitter and the
power supply have their own plug-in jacks. Additional emitters can be used from the auxiliary emitter jack.
Utilizing the Audioplex IRS-1, up to (4) additional hard wired emitters can be used. Follow the wiring
diagram below for basic set up. Note that if using IRTargets with System Status, the SYS-TAT power supply
should be plugged into a switched outlet on your A/V receiver.
2006 - 4/10/06
TO BE USED WITH AUDIOPLEX BRAND IR ONLY!
disc 5 2.53
tape b
12 VDC
POWER
SUPPLY
OPTIONAL
SYS-TAT 12 VDC
POWER SUPPLY
IRS-1
Stealth Sensor
StealthX40-HW
In-wall IRTarget
WIRING DIAGRAM
OUT TO ADDITIONAL EMITTERS
EMITTERS
+12V
+12V
12VDC
GND
GND
STATUS
STATUS
EMITTERS
IR IN
SIGNAL
+12V
GND
SIGNAL
TECHNOLOGY
IRB-4
out to additional controlled components
L
E
B
M
O
S
R
?
P
N
?
E
S
E
N
D
O
I
H
T
E
S
L
E
P
U
?
Q
CALL
TOLL-FREE
1-800-257-2077
AUDIOPLEX TECHNOLOGY
404 GWH PO BOX 440 MELVIN VILLAGE, NH 03850
1-800-257-2077 IN NH 1-603-544-8601 FAX: 1-603-544-8901
www.audioplex.com e-mail: [email protected]
WARRANTY
Your AUDIOPLEX TECHNOLOGY IRB-4 is covered by a TWO YEAR WARRANTY against any defects in
workmanship and materials. Any defects will be remedied without charge for labor or parts during this time.
Damage incurred by shipping or accident is not considered to be a defect, and not covered by this warranty.
AUDIOPLEX TECHNOLOGY is not responsible for defective operation caused by abuse or by modification or service by
any unauthorized person or agency.
The unit must be properly installed and operated according to instructions for the warranty to apply. Any necessary
servicing must be done by AUDIOPLEX TECHNOLOGY. The product must be returned expenses prepaid, with written
authorization from the company. The product must be shipped with the proof of purchase and in the original carton and
packing material to avoid damage.
This warranty gives you specific legal rights. You may have other rights which vary from state to state.
2006 - 4/10/06
  • Page 1 1
  • Page 2 2

Audioplex IRB-4 Installation guide

Audioplex
Brand
Audioplex
Model
IRB-4
Type
Installation guide

Audioplex IRB-4 is an IR repeating systems termination block designed to work exclusively with Audioplex IR products. It features four 1/8" mono mini-jack emitter outputs, an unregulated +12vdc power supply, and an extra emitter jack that can accommodate up to four additional emitters using the Audioplex IRS-1. The IRB-4 allows for multiple IRTargets to be connected in parallel (up to 12) to the screw-down connector, eliminating the need for hard-wiring.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents