ANCHOR WATER FILTERS AF-9500-M Installation guide

Brand: ANCHOR WATER FILTERS

Model: AF-9500-M

Type: Installation guide

This manual is also suitable for

COUNTERTOP WATER FILTER SYSTEM

Quick Setup Guide

All systems are made with highest quality NSF approved high

performance parts.

Water Filter

System with LCD

display

Comes in:

- white &

chrome finish

With:

- 3, 5, or 7 stage

filter cartridges

Water Filter

System

Comes in:

- white & clear

finish

With:

- 1, 3, 5, 7, or 10

stage filter

cartridges

Anchor Countertop

Water Filter Systems

are attractively

designed units that

sit right on your

countertop and

complete the

filtration process

Just dispense the water you

need and enjoy the filtered

water’s refreshing taste.

These systems are:

• Perfect solution for

household of any size

• Easy to install

• Slim, portable, and

compact in design

• Designed to be used

in most standard sized

housings

Your box contains:
Filter System*
Adapter Ring + 
Gasket
Wrench User Guide
Supported Countertop Water Filter System
The information in this guide applies only to the following products:
AF-3000 Single Stage Filter AF-3200-C 2-Stage Filter
AF-3300 3-Stage Filter AF-3200-W 2-Stage Filter
AF-3500 5-Stage Filter AF-9300-M 3-stage Filter w/LCD display
AF-3700  7-Stage Filter AF-9300-W 3-stage Filter w/LCD display
AF-3110  10-Stage Filter AF-9500 5-stage Filter with LCD display
AF-9700 7-stage Filter with LCD display
- installation steps for 
all the Anchor 
Countertop Filter 
System Products
- replacement steps 
for Anchor 
countertop filter 
cartridges
This Quick Setup 
Guide provides:
* Filter color and cartridge will depend on the order.

Know your filter

Direction of flow of water:

Attribute Value

Temperature Range 39°F - 100°F (4°C - 38°C)

Service Flow 1 gpm (3.8L/min)

Rated Capacity 1500 gallons

Operating Pressure 20 psi - 125 psi

Shipping Dimensions 6" x 5" x 13" H

Shipping Weight Varies between 6-8 lbs based on filter cartridge

Specifications

Various parts of the filter:

We have made it easy for you to install the Anchor Countertop Water

Filter. The shipped unit comes pre-installed with filter cartridge, faucet,

diverter valve, and tube. The only thing you need to do is to connect the

diverter valve to your faucet and start enjoying the clean refreshing water.

OUTSIDE

INSIDE

- OR -

Note the threads in your faucet. If the threads are on the:

Installing your filter

This is the

diverter valve

Steps for installation:

1. Remove existing aerator from the faucet

Aerator

2. Based on your faucet threads described above, connect

the divertor on the faucet as shown in the image below:

Faucet with outside thread

- the diverter valve should

screw right on

After setting up the faucet, do

the following:

1. Place the filter unit in a

convenient location with

the spout positioned over

your sink. The spout is

designed to swivel.

2. Turn on your cold water and

divert the water through the

filter by pulling out/turning

the knob on the diverter

valve. Water pressure

should hold it in the out

position.

3. Allow it to run for several

minutes to flush out the

normal carbon fines

(blackish specs). Initially, the

water may contain tiny air

bubbles and taste slightly

sweet - this is normal and

harmless, and will clear up

after flushing.

4. To stop the flow, turn off the

cold water at your faucet -

the diverter valve knob will

return automatically for

normal unfiltered water

flow through your kitchen

faucet.

Faucet with inside thread

- enclosed adapter ring and

gasket must be used

Countertop with filter installed

If your faucet has non-standard

threads, you may need to

purchase a special adapter from

your local hardware store.

1. Turn off water.

2. Unscrew housing from its base.

Note: If the housing seems stuck, soak the base of the housing

for 10 minutes in a mixture of HOT water and a little vinegar.

3. Place Housing upside down on cabinet and remove used cartridge.

3. Check the O ring for wear and tear. (The O ring rests in a groove 1

“down in the housing).

a. If it is worn replace it.

b. If O ring is in good working order,

Note: lubricate it with petroleum jelly to ensure it lies flat

and prevents leaking.

Replacing Your Cartridge

6. Leave the housing on the counter, pick up the base, and screw it

back on tight enough to prevent any leakage. Doing it this way will

prevent the O- ring from slipping loose and causing the filter to

leak. Turn the housing/canister right side up.

Note: Before putting the housing back on, put some petroleum

jelly on the plastic threads this will make it easier to unscrew the

housing the next time you change your filter cartridge.

5. Unwrap filter cartridge

from the plastic wrap. With

your housing’s open end

facing up, place the new

filter into the housing

reproduced, distributed, or transmitted in any form or

by any means, including photocopying, recording, or

other electronic or mechanical methods, without the

prior written permissionof Anchor USA.

Technical Support

At Anchor USA, we are always here to help you. With 24-hour access to

our company contact web page, you can drop a message or email us

directly anytime, and one of our representatives will respond to your

query in less than 24-hrs.

Web: https://www.anchorfilters.com/contact-us

Email: support@anchorfilters.com

IMPORTANT!

Run only cold water through the unit.

WARNING!

Do not use this filter for water that is microbiologically

unsafe or of unknown quality.

SN0010EN2019

ANCHOR WATER FILTERS AF-9500-M Installation guide

Brand: ANCHOR WATER FILTERS

Model: AF-9500-M

Type: Installation guide

This manual is also suitable for

Download PDF

report

ANCHOR WATER FILTERS AF-9500-M Installation guide

This manual is also suitable for

ANCHOR WATER FILTERS AF-9500-M Installation guide

Related papers

Other documents