ATUH-16A(PCI) User’s Guide
Copyright 2013 CONTEC CO., LTD. ALL RIGHTS RESERVED.
CONTEC CO., LTD. February 2013 Edition
3-9-31, Himesato, Nishiyodogawa-ku, Osaka 555-0025, Japan
Japanese http://www.contec.co.jp/
English http://www.contec.com/ A-51-103 (LYFL143)
Chinese http://www.contec.com.cn/ 02152013_rev3 [10242005]
No part of this document may be copied or reproduced in any form by any means without prior written
consent of CONTEC CO., LTD.
Pin Assignments of ATUH-16A(PCI) CN1
CN1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
Analog Input 16 / 8[+]
Analog Input 24 / 8[-]
Analog Input 17 / 9[+]
Analog Input 25 / 9[-]
Analog Input 18 / 10[+]
Analog Input 26 / 10[-]
Analog Input 19 / 11[+]
Analog Input 27 / 11[-]
Analog Input 20 / 12[+]
Analog Input 28 / 12[-]
Analog Input 21 / 13[+]
Analog Input 29 / 13[-]
Analog Input 22 / 14[+]
Analog Input 30 / 14[-]
Analog Input 23 / 15[+]
Analog Input 31 / 15[-]
Analog Output
Simultaneous Hold Output
+5V DC from PC
Description No.
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
Analog Ground
Analog Ground
Analog Ground
Analog Ground
Analog Ground
Analog Ground
Analog Ground
Analog Ground
Analog Ground
Analog Ground
Analog Ground
Analog Ground
Analog Ground
Analog Ground
Analog Ground
Analog Ground
Analog Ground
Digital Ground
DescriptionNo.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
- Analog Input 16 - 32 are single - ended input channels.
- Analog Input 8[+] - 15[-] differential input channels.
* "Analog Output", "Simultaneous Hold Output", "+5V DC from PC" and "Digital Ground"
are the same signals as the AD12-16U(PCI)EV, AD16-16U(PCI)EV.
- The above figure is an arrangement when the receptacle on the board is seen form the plug.
Installation Procedure
Refer to the following steps for ATUH-16A(PCI) installation.
(1) Connect the ATUH-16A(PCI) to the CN3 of AD12-16U(PCI)EV, AD16-16U(PCI)EV with the
connector cable.
(2) Install the AD12-16U(PCI)EV, AD16-16U(PCI)EV and ATUH-16A(PCI) into the PC expansion
slots.
(3) Stablige the brackets with screws.
Installed to PC
Back of a PC
example : Installed to PC
(using 2 slots)
Fix the bracket
with screw
ATUH-16A(PCI)
AD12-16U(PCI)EV, AD16-16U(PCI)EV
CAUTION
- Turn off PC power before installation.
- The ATUH-16A(PCI) connection cable can only be used for the AD12-16U(PCI)EV,
AD16-16U(PCI)EV. Do not use if for other interface boards.