Zip HydroTap G4 Arc boiling 240 User manual

1

Installation instructions

805845UK v1.02 July 2018 - G4 Command Centre

Technical support

Tel: 0345 6 005 005 Email: [email protected].uk www.zipwater.co.uk

VENTILATION

IS ESSENTIAL

READ SECTION 1

‘VENTILATION’

BEFORE YOU START

Installation instructions

Zip

HydroTap G4

The Worlds most advanced Drinking Water Appliance

Model :

Command Centre (see table of contents for speciﬁc models)

®

2

Installation instructions

805845UK V1.02 July 2018 - G4 Command Centre

Technical support

Tel: 0345 6 005 005 Email: [email protected].uk www.zipwater.co.uk

Tap options

The G4 series offers a range of interchangeable taps to suit the customer's needs.

Classic range

Arc / Cube range

Elite range

All-in-One range

Mixer range

These standalone taps offer instant boiling, chilled

and sparkling water* and are directly compatible with

the G4 Command Centre.

The All-in-One tap may be used as alternatives to

the above HydroTap and mixer tap combinations*.

The mixer tap range may be used in conjunction with

any of the above to provide mixed hot and cold water

for sanitary use*.

Celsius range

The Celsius range offer instant boiling, chilled and

sparkling / boiling and chilled / boiling and ambient

/ chilled and sparkling / chilled or boiling* water

together with the an integral mixer to provide mixed

hot and cold water from the mains.

*Dependant upon model purchased.

3

Installation instructions

805845UK v1.02 July 2018 - G4 Command Centre

Technical support

Tel: 0345 6 005 005 Email: [email protected].uk www.zipwater.co.uk

HydroTap

G4 specifications

Installation check list .................................................................................................................... 4

General product features ............................................................................................................. 5

Important safety instructions ........................................................................................................ 6

Warnings and regulatory information ........................................................................................... 7

Major components and accessories ............................................................................................. 8

Tap - Command Centre compatibility ........................................................................................... 9

Technical specifications ............................................................................................................... 11

Before installation and site requirements ..................................................................................... 12

Installation instructions

Step 1 -

Measure and cut all the tap holes, fit the taps : Refer to 803341UK Tap installation instructions.

Step 2

- Check for adequate ventilation.

Section 1 - Ventilation.

Section 1.1 - 1.9 Ventilation for all models ................................................................................... 13

Step 3

- Install the booster / scale filter / water block / carbonation valve (if required).

Section 2 - Booster installation ..................................................................................................... 21

Section 3 - Scale filter installation ................................................................................................ 24

Section 4 - CO2 cylinder installation ............................................................................................. 25

Section 5 - Water block installation .............................................................................................. 27

Section 6 - Carbonation valve installation .................................................................................... 29

Step 4

- Install the Command Centre.

Section 7 Commercial & residential Command Centre installation.

Section 7.1 - Generic Command Centre installation instructions ................................................. 30

Section 7.2 - External bypass valve ............................................................................................. 31

Section 7.3 - 5253UK & 5053UK BCS commercial installation .................................................... 33

Section 7.4 - 2957UK, 2857UK, 1456UK & 1256UK BCS comm. and res. compact installation . 38

Section 7.5 - 5261UK & 5061UK BC commercial installation ...................................................... 43

Section 7.6 - 2924UK, 2824UK,1414UK & 1214UK BC comm. and res. compact installation .... 48

Section 7.7 - 5200UK, 5201UK, 5000UK, 5001UK 1500UK, 1501UK, 1300UK,1301UK

BO, BA installation ....................................................................................................................... 53

Section 7.8 - 0053UK CS commercial installation ........................................................................ 60

Section 7.9 - 0061UK C commercial installation .......................................................................... 63

Section 7.10 - 0056UK CS residential installation ........................................................................ 66

Section 7.11 - 0015UK C residential installation .......................................................................... 69

Step 5

- Commission the HydroTap

G4.

Section 8 - Commissioning

Section 8.1 - Generic commissioning instructions ....................................................................... 72

Section 8.2 - Select the language ................................................................................................ 72

Section 8.3 - CO2 purge ............................................................................................................... 72

Section 8.4 - Filter flush ............................................................................................................... 73

Section 8.5 - Boiling calibration .................................................................................................... 73

Section 8.6 - Booster enable ........................................................................................................ 73

Section 8.7 - Safety sensor calibration ......................................................................................... 74

Section 8.8 - System flush ........................................................................................................... 74

Trouble shooting

Trouble shooting table .................................................................................................................. 76

End of life disposal ....................................................................................................................... 77

Warranty ....................................................................................................................................... 78

Contact details ............................................................................................................................. 80

Table of contents

4

Installation instructions

805845UK V1.02 July 2018 - G4 Command Centre

Technical support

Tel: 0345 6 005 005 Email: [email protected].uk www.zipwater.co.uk

Before installation

• Read the instructions and check if there is adequate space to install all of the components.

• Note Not all fittings are supplied with the appliance kit. Isolation valves are not supplied.

• Check the mains water pressure is within min / max requirements (see page 11).

• Check the water quality to determine if extra filtration will be required.

• Note This product must be fitted to a wholesome water supply.

• Check the Command Centre rating plate and ensure correct power is available.

• Check the under counter cupboard floor supporting the Command Centre is adequate for its total

weight, when full of water.

Before commissioning

• Check the system has been installed correctly.

• Check all plumbing fittings for water tightness.

• Ensure the outlet and vent pipes are positioned to drain correctly.

• Ensure there is adequate ventilation.

• Check all tubes and pipes from the Command Centre to the tap have a constant rise and there are

no sags or kinks in the hoses.

• Check all electrical connections are correct and there are no loose wires.

Commission (see section 8)

• Flush the supply line before connecting.

• Turn on the water and check for leaks.

• Flush the filter(s).

• Activate / enable the booster (if fitted).

• Calibrate the safety sensor for boiling models.

• Where applicable, programme the Command Centre to suit the customer’s requirements.

Installation checklist

5

Installation instructions

805845UK v1.02 July 2018 - G4 Command Centre

Technical support

Tel: 0345 6 005 005 Email: [email protected].uk www.zipwater.co.uk

Thank you for purchasing a Zip HydroTap

G4. Please read and follow these instructions carefully to ensure

safe and trouble free operation. If help and advice is required, please call 0345 6 005 005.

What is the Zip HydroTap

G4 ?

This Zip HydroTap

G4

is an electronically controlled, filtered, boiling, chilled and sparkling (functionality is

dependant upon model purchased) drinking water system for the kitchen. The HydroTap

G4 systems are

under counter drinking water appliances with a dispensing tap mounted on a sink or worktop, which have

been designed for commercial or residential applications. The HydroTap

G4 utilises a conventional refrigerant

compressor to chill the water and an immersion heating element to boil the water.

These units are NOT designed to be used solely as sanitary fixtures.

The Zip HydroTap

G4

models which dispense boiling water are fitted with a tap mounted safety lock. In

addition, there are various energy saving options accessible via the main menu. The system is equipped with

a self-calibrating program which caters for altitude adjustment. The water filter is a disposable item which will

require periodic replacement and is covered by a limited OEM warranty.

It is important that the installation be undertaken safely, correctly and completely in order to utilise all the

benefits that the HydroTap

G4

can provide. HydroTap

G4

Classic taps can be ordered with the tap head

assembly for disabled use. The disabled levers are supplied with Braille caps for the visually impaired.

General product features

Command Centre

6

Installation instructions

805845UK V1.02 July 2018 - G4 Command Centre

Technical support

Tel: 0345 6 005 005 Email: [email protected].uk www.zipwater.co.uk

IMPORTANT SAFETY INSTRUCTIONS

This manual contains important safety and installation instructions for the Zip HydroTap

G4.

Please read all warnings, installation requirements and installation instructions before installing

any Zip HydroTap

G4. This system must be installed in accordance with water supply byelaws,

current IEE regulations and relevant local authority byelaws.

Safety

This appliance is not intended for use by children under 8 years or persons (including children under 8 years)

with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have

been given supervision or instruction concerning the use of the appliance by a person responsible for their

safety. Children should be supervised to ensure that they do not play with the appliance.

Refrigerant

The Zip HydroTap

G4 Command Centre contains R134A refrigerant under pressure. Maintenance of the

refrigeration unit must be carried out by an accredited service provider or qualified refrigeration technician.

CO

2

You can have serious health problems if breathing air containing concentrations of CO

2

up to 15000ppm

(1.5%) for more than 10 minutes. Proper ventilation must be provided to ensure that, in case of escape,

concentrations of CO

2

remain below this level.

Qualifications

If the power cable is damaged it must be repaired only by a qualified technician. To avoid hazards, all

installation procedures must be carried out by a suitably qualified tradesperson. The power cable and power

outlet must be in a safe visible position for connection.

Venting

Sometimes steam and / or boiling water droplets may discharge through a vent outlet on the tap. If the tap

is not installed using the font, ensure the tap body is located so the tap outlet safely dispenses into the sink

bowl area.

Lifting

Take care when lifting. The Command Centre may exceed safe lifting limits. If you feel this is beyond your

personal capabilities, please seek assistance with the lift. The weight of the Command Centre is marked

on the packaging. Do not lift the Command Centre by the front cover or any of its connections. Refer to the

technical specification, see page 11, for the weight of the product.

Airflow

The Zip HydroTap

G4 operates within the ambient temperature range 5ºC - 35ºC. Proper air circulation must

be provided. The system will operate satisfactorily only if the recommended air gaps are provided. See

Section 1 'Ventilation', page 13, for correct installation to prevent overheating. The vent kit supplied must be

fitted.

Altitude

Water boils at varying temperatures at different altitudes. The HydroTap

G4 adjusts for this during startup

calibration and will recalibrate itself on a regular basis.

Frost protection

If the HydroTap

G4 is located where the ambient air temperature could fall below 5ºC when the heater is

not in use, do not turn off the appliance electrically. This safeguard does not offer the same protection to the

connecting pipework and fittings.o

!

7

Installation instructions

805845UK v1.02 July 2018 - G4 Command Centre

Technical support

Tel: 0345 6 005 005 Email: [email protected].uk www.zipwater.co.uk

WARNINGS AND REGULATORY INFORMATION

Warnings

• The Zip HydroTap

G4 must be earthed. The resistance of the earth

connection from each exposed metal part must be less than 1Ω.

• All installation and service work must be completed by trained and

suitably qualified tradespeople. Faulty operation due to unqualified

persons working on this product, or any other Zip product may void

warranty coverage.

• As the installer, it is your responsibility to supply (if necessary)

and install all valves as required by local regulations and relevant

standards.

• The HydroTap

G4 is rated for 230V 50/60Hz AC operation (supply

frequency dependant upon model purchased).

• Do not remove the cover of the appliance under any circumstances

without first isolating the appliance from the power supply.

• Never locate the Command Centre near, or clean with water jets.

• Do not expose the Zip HydroTap

G4 to the elements of nature.

• Due to the process of continuous improvement, Zip reserves the right

to change details mentioned in this manual, without notice.

• Visit www.zipwater.co.uk to ensure you have the latest copy of this

document.

!

IMPORTANT SAFETY INSTRUCTIONS

Positioning

It is important to ensure the Command Centre is positioned in an accessible area close to the floor level. The

Command Centre

must have its base mounted in a horizontal position with all inlets and outlets facing up.

The tap must be located above the Command Centre. See Section 7, Command Centre installation.

8

Installation instructions

805845UK V1.02 July 2018 - G4 Command Centre

Technical support

Tel: 0345 6 005 005 Email: [email protected].uk www.zipwater.co.uk

Major components and accessories

Accessories Description

Booster

(inc. connection

hoses)

Scale, taste &

odour filter

Scale filter

installation kit

(Filter not included).

Font, Integrated or

Stand alone

Replacement

internal 0.2 micron

filter

Disabled lever kit

(Classic HydroTap)

Mixer upgrade

All-in-One upgrade

(vented)

(mains)

Recommended

water block

Parts supplied Description

Tap options*

1 x HydroTap

G4

1 x All-in-One

HydroTap

G4

Mains or Vented

1 x mixer tap

Command Centre and components

Duct kit*

1 x Exhaust duct

1 x Mounting plate

2 x Outlet vent

1 x Inlet vent

1 x

Command Centre

with air and water

filters

1 x Mains water

connection hose

1 x Booster inc.

connection hoses

(supplied with

140 or 240 models)

1 x Installation

fittings (supplied

with vented mixer

tap models)

1 x User guide and

1 x Quick start guide

1 x Installation

instruction

801599 - HydroTap User Guide - Nov 2013 UK - V1.05 Page 1 of 20

ZIP HydroTap

User Guide

®

•

Tap Operation...................(Pages 2-5)

•

LCD Screen & Menu .......(Pages 6-18)

•

Maintenance.................... (Pages 18-20)

•

Date of Installation.........

Affix Model Number Label

Here

801599

BC160/125G4

BC240/175G4

BCH160/125G4

BCH240/175G4

AV160/125G4

AN160/125G4

AV240/175G4

AN240/175G4

801600 - Zip Quick Start Guide - October 2013 - V1.06

Parts Supplied Description Parts Supplied Description

1 off

Hydrotap Tap

and hoses

Duct kit

1x Air Duct

1 x Mounting

plate

1 off

Undersink Unit

with air and water-

filter

Vent kit

1 x Kickboard

louvre

1 x Door vent

louvre

1 x front vent grill

1 x Restrictaflow

valve and Tee

piece for Mixer

Taps

1 off

HydroTap

Booster heater

and hoses

(Supplied with

240/175 models)

1 off Mains water

connection hose

QUICK START GUIDE

Note: This quick start guide must be read in conjunction with

the main installation and user instructions

• Before proceeding, read the installation and user instructions

• Check all the components are present and correct.

• Check that you have all the necessary tools

• Ensure the underbench can support the product weight when full of water,

(Check the specifications in the main book and allow an extra 5-8kg when full. )

Before installing ensure the following have been provided at

the installation site:

• Sufficient space in the cupboard to install all of the undersink units in accordance

with these Installation Instructions. Refer to technical specification for dimensions. If

required, make allowance for a booster heater. (Refer to the main book, for detailed

installation instructions).

• A potable water supply connection with isolating valve inside the cupboard within

reach of the flexible braided hose and positioned so that the connection point and the

stop cock will not be obstructed when all the undersink units are installed.

• For Zip HydroTap 160/125 &160/175 models, a 220-240Vac, 10A GPO will be

required. For Zip HydroTap 240/175 models, two 220-240Vac, 10A GPOs will be

required. (One GPO is for the Zip HydroTap and the other for the Booster heater).

NOTE: Check the cable lengths and outlet positions before proceeding.

• A potable cold water supply with a minimum working pressure of 172kPa and a

maximum working pressure of 700kPa connected via an isolation valve.

• For the mains pressure All-IN-ONE, both a hot and cold water supply will be required.

• The undersink appliances must be mounted in upright positions as shown in the

diagrams.

IMPORTANT!

Do not proceed with the installation if these

requirements are not met.

STEP 1-

Prepare and fit the Taps

Hole positioning: Position the tap such that it dispenses into

the sink bowl with ample clearance for a cup or tea pot. Alternatively,

the tap could be mounted away from the sink using a Zip Font, avail-

able as an accessory.

Apply a light smearing of silicon sealant

on the underside of the upper spacer to

ensure a watertight ﬁ t.

For HydroTap and Mixer taps

cut a 35mm hole in the bench / sink top.

BENCH TOP

Ø35mm

HydroTap Tap

Mixer Tap

4-in-1

(If required)

NUT

LOWER RUBBER

WASHER

UPPER

RUBBER

WASHER

BRAIDED

HOSE x 3

UPPER RUB-

BER WASHER

LOWER RUB-

BER WASHER

WASHER

NUT

White Hose

Ext. Mains

Blue band

Mixer IN

Red band

Mixer Out

O-RING

BASE

BLOCK

SPIDER

BASE

BLOCK

NUT

USB

CABLE

ALL

THREAD

ROD

NOTE: feed each of

the tubes and elec-

trical cable evenly in

between the legs of

the BASE BLOCK

SPIDER.

All-In-One Tap

(If required)

For AIO mains and vented Taps

Cut a 50mm hole in the bench / sink top.

NOTE: make sure the tap location will allow the nozzle to drain into the sink.

SINK TOP

50mm

ALL THREAD

ROD

STAINLESS

STEEL

WASHER

SPIDER

CLAMP

NUT

BLACK

PLASTIC

SPACER

NOTE: feed each of the three tubes and

electrical cable evenly in between the legs of

the SPIDER CLAMP when installing.

Fit the

STAINLESS STEEL

WASHER,

SPIDER CLAMP,

AND 6mm NUT.

6mm

NUT

SPIDER

CLAMP

Stainless

washer

Black plastic

spacer

35mm dia hole

Sink

O-RING

SINK TOP

Fit the O-ring to the underside of the AIO tap

then pass all hoses through the 50mm hole.

Chiller

connection

BLUE

From Mixer OUT to Tap - Vented version only

Boiler

connection

RED

Blue ring on

RHS mains IN to

Mixer IN

White ring

on LHS to

Mains in

Tap

O ring Base

Clear tube to Vent

For Accessories contact Zip:

Tel 0345 6 005 005

Website: www.zipwater.co.uk

Email: [email protected]

*Dependant on model purchased

9

Installation instructions

805845UK v1.02 July 2018 - G4 Command Centre

Technical support

Tel: 0345 6 005 005 Email: [email protected].uk www.zipwater.co.uk

Tap - Command Centre compatibility

Commercial B, BA, BC and BCS HydroTap

G4 range

All-in-One Classic

Filtered Boiling and Chilled plus unfiltered Hot and Cold

Filtered Boiling, Chilled and Sparkling plus unfiltered Hot

and Cold

Filtered Chilled

Filtered, Chilled and Sparkling

Commercial C and CS HydroTap

G4 range

HydroTaps

Filtered Chilled plus unfiltered Hot and Cold

Filtered Chilled and Sparkling plus unfiltered Hot and Cold

Celsius

Arc / Cube

Elite Classic

HydroTaps

Mixer taps

Classic Vented

+

Filtered Boiling

Filtered Boiling and Ambient

Filtered Boiling and Chilled

Filtered Boiling, Chilled and Sparkling

Plus unfiltered Hot and Cold.

Filtered Boiling plus unfiltered Hot and Cold

Filtered Boiling and Ambient plus unfiltered Hot and Cold

Filtered Boiling and Chilled plus unfiltered Hot and Cold

Filtered Boiling, Chilled and Sparkling plus unfiltered Hot

and Cold

Celsius & All-in-One Celsius Arc

All-in-One

Celsius Arc

Arc / Cube

Elite Classic

Celsius

Arc / Cube

All-in-One

Classic

Vented

Celsius

Arc / Cube

All-in-One

Classic

Mains

10

Installation instructions

805845UK V1.02 July 2018 - G4 Command Centre

Technical support

Tel: 0345 6 005 005 Email: [email protected].uk www.zipwater.co.uk

Residential B, BA, BC and BCS HydroTap

G4 range

Arc / Cube

Elite Classic

HydroTaps

Residential C and CS HydroTap

G4 range

Filtered Chilled

Filtered, Chilled and Sparkling

Tap - Command Centre compatibility

Filtered Chilled plus unfiltered Hot and Cold

Filtered Chilled and Sparkling plus unfiltered Hot and Cold

Celsius

Arc / Cube

Celsius

All-in-One taps

All-in-One

Classic

Vented

Arc / Cube

Elite Classic

HydroTaps

Mixer taps

Arc Mains Cube Mains

+

Filtered Boiling

Filtered Boiling and Ambient

Filtered Boiling and Chilled

Filtered Boiling, Chilled and Sparkling

Filtered Boiling plus unfiltered Hot and Cold

Filtered Boiling and Ambient plus unfiltered Hot and Cold

Filtered Boiling and Chilled plus unfiltered Hot and Cold

Filtered Boiling, Chilled and Sparkling plus unfiltered

Hot and Cold

Celsius

Arc / Cube

Celsius & All-in-One Celsius Arc

All-in-One

Celsius Arc

Filtered Boiling and Chilled plus unfiltered Hot and Cold

Filtered Boiling, Chilled and Sparkling plus unfiltered Hot

and Cold

Plus unfiltered Hot and Cold

All-in-One

Classic

Mains

11

Installation instructions

805845UK v1.02 July 2018 - G4 Command Centre

Technical support

Tel: 0345 6 005 005 Email: [email protected].uk www.zipwater.co.uk

Command

Centre

Capacity boiling

(167ml cups

/hr)

Capacity

chilled/

sparkling

(200ml

glasses/hr)

Power

rating

(kW)

230V

Boost

rating

(kW)

230V

Boost

(10A)

**13A sockets

required

Unit Dimensions****

W x D x H (mm) with air

duct

***Dry

weight

(kg)

Commercial Command Centres

Filtered Boiling, Chilled and Sparkling, with and without booster

5253UK

#

5053UK

160 / 240* 175 2.30 2.20 optional 1 / 2* 450 x 470 x 335 39

2957UK

#

2857UK

100 / 140* 75 2.13 2.20 optional 1 / 2* 338 x 461 x 335 30

Filtered Boiling and Chilled, with and without booster

5261UK

#

5061UK

160 / 240* 175 2.13 2.20 optional 1 / 2* 450 x 470 x 335 28

2924UK

#

2824UK

100 / 140* 75 2.05 2.20 optional 1 / 2* 280 x 470 x 335 22

Filtered Boiling and Ambient, with and without booster

5201UK

#

5001UK

160 / 240* - 1.90 2.20 optional 1 / 2* 280 x 313 x 335 13

Filtered Boiling, with and without booster

5200UK

#

5000UK

160 / 240* - 1.90 2.20 optional 1 / 2* 280 x 313 x 335 11

Filtered Chilled and Sparkling

0053UK - 175 0.45 - - 1 336 x 476 x 335 36

Filtered Chilled

0061UK - 175 0.3 - - 1 336 x 480 x 335 24

Residential Command Centres

Filtered Boiling, Chilled and Sparkling, with and without booster

1456UK

#

1256UK

1.7 2.2 optional 1 / 2* 338 461 x 335 30

Filtered Boiling and Chilled, with and without booster

1414UK

#

1214UK

1.55 2.2 optional 1 / 2* 280 x 470 x x335 21

Filtered Boiling and Ambient, with and without booster

1501UK

#

1301UK

1.43 2.2 optional 1 / 2* 280 x 313 x 335 13

Filtered Boiling, with and without booster

1500UK

#

1300UK

1.43 2.2 optional 1 / 2* 280 x 313 x 335 11

Filtered Chilled and Sparkling

0056UK 0.35 - - 1 280 x 405 x 335 30

Filtered Chilled

0015UK 0.13 - - 1 280 x 420 x 335 20

#

Supplied with venturi for vented mixer tap

* With boost

** One for the Command Centre, and one for the booster

*** Add 3 - 8Kg when full

**** Refer to Section 7, Command Centre installation, for clearance envelope.

Component Min. / Max. water supply pressure MPa (bar)

(in a G4 Hydrotap system)

HydroTap 0.17 (1.7) - 0.5 (5.0)

Sparkling Hydrotap 0.25 (2.5) - 0.5 (5.0)

Mixer tap 0.20 (2.0) - 0.5 (5.0)

Booster 0.20 (2.0) - 0.5 (5.0)

Scale filter 0.20 (2.0) - 0.5 (5.0)

Technical specifications

Water supply pressure requirements

12

Installation instructions

805845UK V1.02 July 2018 - G4 Command Centre

Technical support

Tel: 0345 6 005 005 Email: [email protected].uk www.zipwater.co.uk

Before installation

Before installation ensure that the following have been

provided at the installation site

•

Review of all the technical specifications.

•

Ensure the under counter cupboard floor can support the product weight

when full of water (allow an extra 3-8kg when full).

•

Sufficient space in the cupboard to install the Command Centre and

other components in accordance with these installation instructions. See

Technical specification, page 11 for dimensions. Make allowance for a

booster if required. See sections 2 page 21 for installation instructions.

•

For Zip HydroTap

G4 models without booster, 1 x 220-240V AC 13A socket

will be required.

For Zip HydroTap

G4 models with booster, 2 x 220-240V AC 13A sockets will

be required.

(One socket is for the Command Centre and the other for the booster).

•

Both the Command Centre and booster must be installed in accordance

with IEE regulations, See Technical specification, page 11 for power

ratings.

Note Check all cable and hose lengths against inlet /outlet positions before

proceeding (see section 7 for general layout).

•

A wholesome water supply connection with a minimum working pressure

of: (see page 11 min. / max. water supply pressure) with isolating valve

inside the cupboard within reach of the braided hoses and positioned so

that the connection point and the stop cock will not be obstructed when

the Command Centre is installed.

•

For the All-in-One, Celsius and Mains mixer taps a hot and cold water

supply are required. (see page 11 for min/max. water supply pressure).

•

If external filtration or a lime-scale protection filter is required, then it is

important to allow extra space for it.

•

If pressure is likely to exceed 0.5 MPa (5 bar), install a 0.35 MPa (3.5

bar) pressure limiting valve.

•

The appliance must be placed with its base in a horizontal position.

•

Ensure proper ventilation for CO

2

, see Important safety instructions, page

6.

IMPORTANT!

Do not proceed with the installation if these requirements are

not met.

!

13

Installation instructions

805845UK v1.02 July 2018 - G4 Command Centre

Technical support

Tel: 0345 6 005 005 Email: [email protected].uk www.zipwater.co.uk

Section 1

Ventilation

Ventilation table of contents

1.1 Generic requirements ............................................................................................................. 13

1.2 BC,BCS Commercial Command Centre installation .............................................................. 14

1.3 BC, BCS Commercial compact Command Centre installation ............................................... 16

1.4 BO,BA Commercial and Residential Command Centre installation ....................................... 17

1.5 CS, C Commercial Command Centre installation .................................................................. 18

1.6 BC, BCS, CS, C Residential Command Centre installation ................................................... 20

Generic requirements

!

Important Read this section in conjunction with section 7 Command Centre installation,

page 30.

When installing air flow vents, the following tools will be required

•

Jigsaw and drill or equivalent equipment.

•

Keyhole or wall board saw.

1.1 Generic requirements

Clearance envelope

• A clearance envelope around all Command Centres must be provided to allow adequate

ventilation for the safe and effective use of the HydroTap G4 system.

!

535mm

50mm

Command Centre

width

14

Installation instructions

805845UK V1.02 July 2018 - G4 Command Centre

Technical support

Tel: 0345 6 005 005 Email: [email protected].uk www.zipwater.co.uk

1.2.2 Preferred ventilation arrangement shown below.

The ducted vent kit supplied with the Command Centre exhausting through the kick-space should be used, to

provide adequate ventilation in all conditions. (Ancillary components are not shown in these diagrams).

A

B

C

100mm

min.

Inlet grille

Position vent grille on

either the kick board or the

cupboard ends

Inlet grille should be

fitted in baseboard

A

Cupboard back must be

fully closed to prevent

recirculation into

cupboard from

kick space.

1.2 BC, BCS Commercial Command Centres

Ventilation

1.2.1 Ventilation for all models

• The clearance envelope dimensions stated in the Specification sheets and Installation instructions must

be observed.

• Adequate ventilation must be provided to ensure that the cupboard temperature doesn't exceed 35

0

C.

Vent cut-out details

A Air outlet vent

(flat vent)

B Air inlet vent

314

Ø

12 x 2

326

5

43max

285

60

Ø

12 X 4

=

45

284

Ø

12 x 4

C Ducted vent

15

Installation instructions

805845UK v1.02 July 2018 - G4 Command Centre

Technical support

Tel: 0345 6 005 005 Email: [email protected].uk www.zipwater.co.uk

1.2.3 Alternative arrangement (Dual fan kit)

In situations where the preferred arrangement cannot be used or will not work effectively e.g.

• Single cupboard where the 100mm grille spacing cannot be achieved.

• Where there are openings in the back of the cupboard allowing exhaust air to recirculate into the cupboard

space.

An SP93156 Dual exhaust fan kit* must be fitted in either arrangement A or B shown below and connected to

the DIN socket on the Command Centre

.

A Fan kit fitted to kick board and with kick space duct fitted to the Command Centre.

B Fan kit fitted to cupboard door (position B1) or side (position B2) and without kick space duct fitted to the

Command Centre.

*

For dual exhaust fan cut-out dimensions see the instructions provided with the kit.

B

A

B2

B1

Vent tray

100mm

min.

1.2 4 Alternative arrangement (Vent tray)

In situations where cupboard width is 1000mm or greater, without central pillar or where the rear of the

cupboard is not sealed and where vent grilles cannot be fitted in the kick board (e.g. hospitals) use a Vent

tray kit Call Zip on 0345 6 005 005.

A vent grille, supplied should be used as an inlet vent and fitted to the cabinet side (adjacent to the

Command Centre air inlet) as shown below. It must

take in air from the room or another ventilated

space. This space could be an adjacent cupboard,

(via a communicating port) on condition that it does

not contain a heat generating appliance. The vent

grille or the angled inlet grille supplied should be

fitted in the adjacent cupboard, observing 100mm

separation from the vent tray exhaust.

Ventilation

16

Installation instructions

805845UK V1.02 July 2018 - G4 Command Centre

Technical support

Tel: 0345 6 005 005 Email: [email protected].uk www.zipwater.co.uk

1.3.1 Ventilation for all models

• The clearance envelope dimensions stated in the specification sheets and installation instructions must

be observed.

• Adequate ventilation must be provided to ensure that the cupboard space temperature does not exceed

35

0

C.

1.3.2 Preferred arrangement

• The vent kit supplied with the Command Centre should be used to provide adequate ventilation by

convection in normal usage.

Note The vent kit has to be installed in a way that allows air to be drawn in from the bottom of the cupboard

and expelled through the top of the cupboard. The outlet vent A should be towards the top of the door (position

A2) or side of the cupboard (position A1). (Where possible

air inlet vent and the air outlet vent should be positioned at

opposite ends of the same cupboard space).

A1

A2

Vent cut-out details

*A Air outlet vent

B

1.3.3 Alternative arrangement

In situations where the preferred arrangement does not

provide adequate ventilation by natural convection a Dual

exhaust fan kit* (SP93156) must be fitted to the cupboard

door or side (as shown in the illustration below) and

connected to the Command Centre

DIN socket.

* For dual

exhaust

fan cut-out

dimensions

see the

instructions

provided with

the kit.

B

A1

A2

B Air inlet vent

Note Flat outlet vent detail shown above, louvred outlet vent

also supplied.

1.3 BC, BCS Commercial compact Command Centres

Ventilation

285

60

Ø

12 X 4

=

314

Ø

12 x 2

326

5

43max

17

Installation instructions

805845UK v1.02 July 2018 - G4 Command Centre

Technical support

Tel: 0345 6 005 005 Email: [email protected].uk www.zipwater.co.uk

1.4.1 Ventilation for all models

• The clearance envelope dimensions stated in the specification sheets and installation instructions must

be observed.

• Adequate ventilation must be provided to ensure that the cupboard space temperature does not exceed

35

0

C.

1.4.2 Preferred arrangement

• 4mm door buffers (at the four corners of each door) supplied with the Command Centre should be used

to provide adequate ventilation in normal usage, see illustration below.

Door buffer

1.4 BO & BA Commercial, BO & BA Residential Command Centres

Ventilation

18

Installation instructions

805845UK V1.02 July 2018 - G4 Command Centre

Technical support

Tel: 0345 6 005 005 Email: [email protected].uk www.zipwater.co.uk

1.5.2 Preferred ventilation arrangements for CS models

The ducted vent kit supplied with the Command Centre exhausting through the kick-space should be used, to

provide adequate ventilation in all conditions. (Ancillary components are not shown in these diagrams).

1.5.1 Ventilation for all models

• The clearance envelope dimensions stated in the specification sheets and installation instructions must

be observed.

• Adequate ventilation must be provided to ensure that the cupboard space temperature does not exceed

35

0

C.

B

A

C

100mm min.

Cupboard back must be fully

closed to prevent recirculation

into cupboard from kick space.

A

1.5 CS & C Commercial Command Centres

Ventilation

Vent cut-out details

A Air outlet vent

(flat vent)

B Air inlet vent

314

Ø

12 x 2

326

5

43max

285

60

Ø

12 X 4

=

45

284

Ø

12 x 4

C Ducted vent

19

Installation instructions

805845UK v1.02 July 2018 - G4 Command Centre

Technical support

Tel: 0345 6 005 005 Email: [email protected].uk www.zipwater.co.uk

1.5.3 Alternative arrangement (Dual fan kit)

In situations where the preferred arrangement cannot be used or will not work effectively e.g.

• Single cupboard where the 100mm grille spacing cannot be achieved.

• Where there are openings in the back of the cupboard allowing exhaust air to recirculate into the cupboard

space.

An SP93156 Dual exhaust fan kit* must be fitted in either arrangement A or B shown below and connected to

the DIN socket on the Command Centre

.

A Fan kit fitted to kick board and with kick space duct fitted to the Command Centre.

B Fan kit fitted to cupboard door (position B1) or side (position B2) and without kick space duct fitted

to the Command Centre.

*

For dual exhaust fan cut-out dimensions see the instructions provided with the kit.

B1

B2

A B

1.5.4 Alternative arrangement (Vent tray)

In situations where cupboard width is 1000mm or greater, without central pillar and where vent grilles cannot

be fitted in the kick board (e.g. hospitals) use a Vent tray kit (CS SP93541).

Vent tray

100mm

min.

A vent grille, supplied should be used as an inlet vent and fitted to the cabinet side (adjacent to the

Command Centre air inlet) as shown below. It must take in air from the room or another ventilated space.

This space could be an adjacent cupboard, (via a communicating port) on condition that it does not contain

a heat generating appliance. The

vent grille or the angled inlet grille

supplied should be fitted in the

adjacent cupboard, observing

100mm separation from the vent

tray exhaust.

Ventilation

20

Installation instructions

805845UK V1.02 July 2018 - G4 Command Centre

Technical support

Tel: 0345 6 005 005 Email: [email protected].uk www.zipwater.co.uk

1.6.3 Alternative arrangement

• For high use applications where the cupboard space

temperature is near 35

0

C or higher, the vent kit supplied can

be used to provide further ventilation by convection.

Note The vent kit has to be installed in a way that allows air

to be drawn in from the bottom of the cupboard and expelled

through the top of the cupboard. The outlet vent should be

towards the top of the door (position A1) or side of the cupboard

(position A2).

(Where possible air inlet vent and the air outlet vent should be

positioned at opposite ends of the same cupboard space).

1.6.1 Ventilation for all models

• The clearance envelope dimensions stated in the specification sheets and installation instructions must

be observed.

• Adequate ventilation must be provided to ensure that the cupboard space temperature does not exceed

35

0

C.

1.6.2 Preferred arrangements

4mm door buffers (at the four corners of each door) supplied with the Command Centre

should be used to

provide adequate ventilation in normal usage, see illustration below.

Door buffer

A1

A2

B

Vent cut-out details

A1 or A2 Air outlet vent

B Air inlet vent

Note Flat outlet vent

detail shown, louvred

outlet vent also supplied.

1.6 BC, BCS, CS, C Residential Command Centres

Ventilation

314

Ø

12 x 2

326

5

43max

285

60

Ø

12 X 4

=

Page is loading ...

Zip HydroTap G4 Arc boiling 240 User manual

Zip HydroTap G4 Arc boiling 240 User manual

Related papers

Other documents