ADEMCO VISTA-20HWse Installation Instructions Manual

VISTA-20

SE

2-PARTITIONED

SECURITY SYSTEM

INSTALLATION

INSTRUCTIONS

®

Principal changes between the VISTA-20SE and the

former VISTA-20 are indicated by margin lines.

N7526V4 Rev B 4/99

WWW.DIYALARMFORUM.COM

–2–

RECOMMENDATIONS FOR PROPER PROTECTION

The Following Recommendations For The Location Of Fire And Burglary Detection

Devices Help Provide Proper Coverage For The Protected Premises.

Recommendations For Smoke And Heat Detectors

With regard to the number and placement of smoke/heat detectors, we subscribe to the

recommendations contained in the National Fire Protection Association's (NFPA) Standard #72

noted below.

Early warning fire detection is best achieved by the installation of fire detection equipment in all

rooms and areas of the household as follows: For minimum protection a smoke detector should be

installed outside of each separate sleeping area, and on each additional floor of a multi-floor

family living unit, including basements. The installation of smoke detectors in kitchens, attics

(finished or unfinished), or in garages is not normally recommended.

For additional protection the NFPA recommends that you install heat or smoke detectors in the

living room, dining room, bedroom(s), kitchen, hallway(s), attic, furnace room, utility and storage

rooms, basements and attached garages.

In addition, we recommend the following:

• Install a smoke detector inside every bedroom where a smoker sleeps.

• Install a smoke detector inside every bedroom where someone sleeps with the door partly or

completely closed. Smoke could be blocked by the closed door. Also, an alarm in the hallway

outside may not wake up the sleeper if the door is closed.

• Install a smoke detector inside bedrooms where electrical appliances (such as portable

heaters, air conditioners or humidifiers) are used.

• Install a smoke detector at both ends of a hallway if the hallway is more than 40 feet (12

meters) long.

• Install smoke detectors in any room where an alarm control is located, or in any room where

alarm control connections to an AC source or phone lines are made. If detectors are not so

located, a fire within the room could prevent the control from reporting a fire or an intrusion.

THIS CONTROL COMPLIES WITH NFPA REQUIREMENTS FOR

TEMPORAL PULSE SOUNDING OF FIRE NOTIFICATION APPLIANCES.

DINING

KITCHEN

BEDROOM

LIVING ROOM

✪

▲

BEDROOM

BDRM

DINING

LIVING ROOM

TV ROOM

KITCHEN

■

✪

✪✪

✪

▲

✪

BEDROOM

TO

BR

■

LVNG RM

BASEMENT

KTCHN

▲

.

CLOSED

DOOR

GARAGE

▲

Smoke Detectors for Minimum Protection

Smoke Detectors for Additional Protection

Heat-Activated Detectors

Recommendations For Proper Intrusion Protection

For proper intrusion coverage, sensors should be located at every possible point of entry to a home or

commercial premises. This would include any skylights that may be present, and the upper windows

in a multi-level building.

In addition, we recommend that radio backup be used in a security system so that alarm signals can

still be sent to the alarm monitoring station in the event that the telephone lines are out of order

(alarm signals are normally sent over the phone lines, if connected to an alarm monitoring station).

WWW.DIYALARMFORUM.COM

–3–

TABLE OF CONTENTS

Section 1. GENERAL DESCRIPTION ............................................................................................. 7

Section 2. INSTALLING THE CONTROL..................................................................................... 10

Mounting the Cabinet........................................................................................................ 10

Installing the Lock (if used) ............................................................................................. 10

Mounting the Control's Circuit Board Alone in the Cabinet........................................... 11

Mounting Control and RF Receiver Circuit Boards Together in the Cabinet................ 11

Standard Phone Line Connections.................................................................................... 12

Wiring the AC Transformer .............................................................................................. 12

Installing the Back-Up Battery......................................................................................... 13

Earth Ground Connections ............................................................................................... 13

Section 3. INSTALLING REMOTE KEYPADS............................................................................. 14

Keypads That May Be Used.............................................................................................. 14

Wiring The Keypads.......................................................................................................... 14

Mounting The Keypads...................................................................................................... 15

Using A Supplementary Power Supply To Power Additional Keypads.......................... 15

Preliminary Check-Out Procedure.................................................................................... 16

Section 4. BASIC HARD-WIRED ZONES 1–8............................................................................... 17

Installing the Hard-Wired Zones ...................................................................................... 17

Common Characteristics For Zones 1–8........................................................................ 17

Wiring Burglary and Panic Devices to Zones 1–8......................................................... 17

Wiring 2-Wire Smoke Detectors to Zone 1 .................................................................... 17

“Verify” Operation of 2-Wire Smoke Detectors in Zone 1............................................. 17

Turning Off Fire Alarm Sounding ................................................................................. 18

Wiring 4-Wire Smoke/Combustion Detectors on Zones 2–7......................................... 18

Wiring 2-Wire Latching Type Glass Break Detectors on Zone 8................................. 19

Check-Out Procedure for Hard-Wired Zones ................................................................... 20

Section 5. WIRED ZONE EXPANSION (4219, 4229) ................................................................... 21

Installing Zone Expansion Units ...................................................................................... 21

Connections and Set-Up................................................................................................. 21

Check-Out Procedure for Wired Expansion Zones........................................................... 22

Section 6. WIRELESS ZONE EXPANSION (5800 SYSTEM) ..................................................... 23

General Information.......................................................................................................... 23

Receiver Supervision ...................................................................................................... 23

House Identification ....................................................................................................... 23

Installing the 5881/5882 RF Receiver............................................................................... 23

RF System Installation Advisories ................................................................................ 23

Installation and Set-Up of the 5881/5882 Receiver ...................................................... 24

Installing the 5800TM Module.......................................................................................... 25

Mounting the 5800TM Module ...................................................................................... 25

5800TM Wiring Connections ......................................................................................... 25

5800 Series Transmitters .................................................................................................. 25

General............................................................................................................................ 25

Transmitter Supervision................................................................................................ 25

Transmitter Input Types ............................................................................................... 26

Transmitter Battery Life ............................................................................................... 26

Using the Transmitter Sniffer Mode ................................................................................ 26

5800 Series Transmitters Table........................................................................................ 27

Section 7 RELAY OUTPUTS & POWERLINE CARRIER DEVICES...................................... 29

Relay/Powerline Carrier Device Basics ............................................................................ 29

Nos. 4204 And 4229 Output Relay Modules .................................................................... 29

4204/4229 Setup.......................................................................................................... 29

Powerline Carrier Devices................................................................................................. 30

Wiring Connections..................................................................................................... 31

WWW.DIYALARMFORUM.COM

–4–

Section 8. 4285 PHONE MODULE.................................................................................................. 32

Installing the Phone Module ............................................................................................. 32

General Information....................................................................................................... 32

Mounting The Phone Module......................................................................................... 32

Phone Module Wiring..................................................................................................... 33

Caller ID Units ............................................................................................................... 33

Checking the Operation of the 4285 Phone Module......................................................... 35

Section 9. EXTERNAL SOUNDERS............................................................................................... 36

Compatible Sounders......................................................................................................... 36

Sounder Connections......................................................................................................... 37

Testing the Sounder........................................................................................................... 37

Section 10. LONG RANGE RADIO ................................................................................................... 38

General Information.......................................................................................................... 38

Connection.......................................................................................................................... 38

Section 11. AUDIO ALARM VERIFICATION (AAV) UNIT.......................................................... 39

General Information.......................................................................................................... 39

Wiring Connections............................................................................................................ 39

Section 12. FINAL POWER UP ......................................................................................................... 41

Earth Ground Connections ............................................................................................... 41

Connecting the Back-Up Battery...................................................................................... 41

Calculating the Battery Size Needed ............................................................................ 41

Making the Battery Connections................................................................................... 42

Auxiliary Device Current Draw Worksheet ..................................................................... 42

Section 13. MECHANICS OF PROGRAMMING ............................................................................ 43

General Programming Information.................................................................................. 43

Entering Program Mode.................................................................................................... 43

Programming a Data Field................................................................................................ 43

Reviewing a Data Field/Erasing an Entry in a Data Field ............................................. 44

Interactive Mode Programming (

✱

56,

✱

80,

✱

82, and

✱

83) .............................................. 44

Loading Factory Defaults .................................................................................................. 44

Programming System Setup Fields .................................................................................. 44

Exiting the Programming Mode........................................................................................ 44

Section 14. ZONE RESPONSE TYPE DEFINITIONS................................................................... 45

Section 15. DATA FIELD DESCRIPTIONS .................................................................................... 47

Section 16. ZONE PROGRAMMING (*56 Menu Mode)................................................................ 57

Section 17. OUTPUT DEVICES (*80 Menu Mode) ........................................................................ 61

Section 18. ZONE LISTS (*81 Menu Mode) .................................................................................... 65

Section 19. ALPHA DESCRIPTION PROGRAMMING (*82 Menu Mode)................................ 66

Assigning Zone Descriptors............................................................................................... 66

Entering Zone Descriptors (in program Menu Mode

✱

82)............................................... 66

Adding Custom Words....................................................................................................... 69

Alpha Vocabulary List (For Entering Zone Descriptors)................................................. 70

Character (ASCII) Chart ................................................................................................... 70

Section 20. USING SEQUENTIAL MODE (*83 Menu Mode) ..................................................... 71

Section 21. REMOTE PROGRAMMING AND CONTROL (DOWNLOADING)........................ 74

General Information.......................................................................................................... 74

Equipment Required ......................................................................................................... 74

Inititial Download.............................................................................................................. 74

Remote Programming Information................................................................................... 75

Remote Programming Advisory Notes ............................................................................. 75

Section 22. SYSTEM COMMUNICATION ...................................................................................... 76

Report Code Formats......................................................................................................... 76

Table of Contact ID Codes................................................................................................. 78

WWW.DIYALARMFORUM.COM

–5–

Section 23. SYSTEM OPERATION................................................................................................... 79

Security Codes.................................................................................................................... 79

Keypad Functions.............................................................................................................. 80

Trouble Conditions ............................................................................................................ 82

Section 24. TESTING THE SYSTEM................................................................................................ 83

Test Procedure ................................................................................................................... 83

To the Installer .................................................................................................................. 84

Section 25. TROUBLESHOOTING GUIDE ..................................................................................... 85

Contacting Technical Support In The Event Of Problems .............................................. 87

REGULATORY AGENCY STATEMENTS ...................................................................... 88

Section 26. SPECIFICATIONS & ACCESSORIES ........................................................................ 89

Specifications .....................................................................................................................89

Accessories (Compatible Devices) ..................................................................................... 91

APPENDIX A. 5800 RF System Wireless Transmitters, Input Loop Identification Diagrams....... 92

Index ........................................................................................................................................................94

Limitations Of This Alarm System.................................................................................................... 98

Summary Of Connections ................................................................................................................... 99

Limited Warranty................................................................................................................................ 100

Programming Form........................................................................................................................ Insert

LIST OF FIGURES

Figure 1. Installing the Cabinet Lock................................................................. 10

Figure 2. Mounting The PC Board ..................................................................... 11

Figure 3. Mounting the PC Board & RF Receiver Together in the Cabinet..... 11

Figure 4. Telephone Line Connections ............................................................... 12

Figure 5. Connection of 4300 Transformer to the Control Board ..................... 13

Figure 6. Keypad Connections to the Control Board ......................................... 15

Figure 7. Using a Supplementary Power Supply............................................... 16

Figure 8. 2-Wire Smoke Detector Connected to Zone 1..................................... 18

Figure 9. 4-Wire Smoke Detector Connections (Zones 2–7) .............................. 18

Figure 10. Glass Break Detector Connections to Zone 8 ................................... 19

Figure 11. Wiring Connection, 4219 & 4229 (4229 shown) ............................... 21

Figure 12. 5881/5882 RF Receiver (cover removed)........................................... 24

Figure 13. 4229 Connections To Control ............................................................ 30

Figure 14. 4204 Connections To Control ............................................................ 30

Figure 15. 4300 Transformer Wiring Connections ............................................ 31

Figure 16. 4285 Phone Module Wiring Connections.......................................... 34

Figure 17. Typical Sounder Wiring..................................................................... 37

Figure 18. Long Range Radio Connections......................................................... 38

Figure 19. NOT USED

Figure 20. Connection of AAV Unit When Not Using a 4285 Phone Module... 40

Figure 21. Connection of AAV Unit When Also Using a 4285 Phone Module . 40

Figure 22. VISTA-20SE Summary of Connections .................. Inside Back Cover

WWW.DIYALARMFORUM.COM

–6–

CONVENTIONS USED IN THIS MANUAL

MAIN SECTION TITLES ARE SHOWN IN REVERSE TYPE

Before you begin using this manual, it is important that you understand

the meaning of the following symbols (icons).

U

L

These notes include specific information which must be followed if you are

installing this system for a UL Listed application.

These notes include information that you should be aware of before

continuing with the installation, and which, if not observed, could result in

operational difficulties.

This symbol indicates a critical note that could seriously affect the operation

of the system, or could cause damage to the system. Please read each warning

carefully. This symbol also denotes warnings about physical harm to the

installer.

Enter Zn Num.

(00 = Quit) 01

Many system options are programmed in an

interactive mode by responding to Alpha keypad

display prompts. These prompts are shown in a

double-line box.

✱

00 When programming the system, data fields are

indicated by a “star” (

✱

) followed by the data field

number.

PRODUCT MODEL NUMBERS: Unless noted otherwise, references to

specific model numbers represent Ademco products.

WWW.DIYALARMFORUM.COM

–7–

Section 1. GENERAL DESCRIPTION

The VISTA-20SE is a 2-partition control that supports up to 32 zones, using basic hard-

wired, wired expansion, and/or wireless zones, plus 3 keypad activated zones.

Basic Hardwired Zones

Provides 8 basic hardwired zones having the following characteristics:

• EOLR supervision supporting N.O. or N.C. sensors

• Programmable response time (10, 350, or 700 milliseconds)

• Individually assignable to either partition

• Up to sixteen 2-wire smoke detectors on zone 1

• 4-wire smoke or heat detectors on zones 2 through 7 (as many as can be

powered from AUX power on the control)

• Up to fifty 2-wire latching type glassbreak detectors on zone 8 with auto

reset

Optional Expansion Zones (up to 24 total, wired and wireless)

Wired Expansion:

Supports up to 8 additional wired zones using a 4219 expansion module or

4229 expansion/relay module. These zones have the following

characteristics:

• EOLR supervision supporting N.O. or N.C. sensors

• 300–500 msec normal response with an option for fast (10–15 msec)

response on loop A (first expansion zone)

Wireless Expansion:

Supports up to 24 wireless zones (less if using wired expansion zones).

• Requires the use of a 5881(5882 in Canada) type RF Receiver, as

indicated below

Receiver Model No. of Zones

5881L/5882L Up to 8

5881M/5882M Up to 16

5881H/5882H Up to 24

• Requires the use of 5800 series wireless transmitters

Two Partitions

• Provides the ability to control two separate areas independently, each

area functioning as if it had its own separate control

• Zones (including wireless) assignable to either partition 1 or 2

• Relay and Powerline Carrier device outputs assignable to either

partition 1 or 2, or to both partitions

• Certain system options, such as Entry/Exit delay and Subscriber

Account number, programmed independently for each partition

• Common Zone option allows either partition to arm, while leaving a

common area (ex. lobby or foyer) disarmed for access into the other

partition. Refer to the ZONE LISTS section for details on programming

a common zone.

U

L

In UL installations, the system may be configured as a single partition only.

Remote Keypads

Up to 4 of any of the following keypads may be used in each partition:

Fixed-Word Keypads: 4127* 4137AD 127*6137 and 6128.

*

These keypads cannot be used if the 4285 Phone Module is being used.

Alpha Keypads: 5137AD 6139 (2-line alphanumeric displays)

6138(1-line alphanumeric display).

For programming from a keypad, a 5137AD or 6139 2-line Alpha keypad

must be connected to partition 1 (but need not stay in the system).

WWW.DIYALARMFORUM.COM

–8–

Security Codes

• One installer code for entire system (user 1)

• One Master code for each partition (user 2)

• 12 secondary user codes for each partition (users 3–14)

• One baby-sitter code for each partition (user 15)

• One duress code for each partition (user 16)

Baby-sitter Code: A special code that can only be used to disarm the system

if that particular code was used to arm it.

Duress Code: An emergency code which, when entered by any user to

disarm or arm the system, will send a silent duress message to the central

station.

Keypad Panic Keys

• Up to 3 programmable panic key functions are provided.

• Designated as Zones 95, 96, 99

• Activated by wired & wireless keypads

• Reported separately by partition, distinguished by subscriber ID

number

Zone Monitor Feature

• The control will sense a high resistance in the loops on hard-wired

zones 2–8 if it is present, and will display a trouble message (rather

than an alarm) for the affected zone when the system is in the disarmed

mode. This feature also prevents the system from being armed while

this high resistance condition exists.

Exit Error False Alarm Prevention Feature

• Enables the system to determine the difference between an actual

alarm and an alarm caused by leaving an Entry/Exit or Interior zone

open after the exit delay expires. If not disarmed in time, an alarm will

sound and an “Exit Error” report sent to the central station.

• An Exit Alarm condition will also occur if an Entry/Exit or Interior zone

re-opens within 2 minutes after the end of an exit delay.

Optional Output Relays and Powerline Carrier Devices (X-10 type)

• Up to 4 relays using one 4204 Relay Module

• Up to 2 relays using one 4229 Zone/Relay Module

• Up to 8 Powerline Carrier devices (you must subtract the number of

relay outputs actually used by the 4204 or 4229 modules, if used)

• Actions programmable to respond to zone activity or manual keypad

entries

Powerline Carrier devices require the use of optional 4300 transformer

module instead of the supplied 1321 AC transformer.

Optional Phone Module

• Supports the Ademco 4285 Phone Module on Partition 1 only.

• Provides access to the system via on premises or off-premises phones for

arming, disarming, etc., plus control of relay outputs and Powerline

Carrier devices.

Paging Feature

• If programmed, the paging feature allows certain system conditions to

be reported to a pager, where a 10-digit code indicates the type of

condition that has occurred.

Audio Alarm Verification Option

• Provides a programmable Audio Alarm Verification (AAV) option which

can be used in conjunction with an output relay to permit voice dialog

between an operator at the central station and a person at the premises.

• Requires the use of optional AAV unit, such as Eagle model 1241.

U

L

The AAV option may not be used in UL installations.

WWW.DIYALARMFORUM.COM

–9–

Optional Long Range Radio

• Allows all messages that have been programmed to go to the primary

telephone number to be reported additionally to a 7720PLUS or 7820

radio. Check availability of these models.

Built-in Telephone Line Monitoring Option

• The telephone line voltage can be monitored to supervise the phone line

connection. The panel must be connected to a proper earth

ground or you will get a false line cut indication if this feature

is enabled.

• The loss of the line can optionally cause a local display, or a display and

trouble sound.

Event Logging

• Event Logging feature keeps a record of selected events in a history log

(up to 48 events). All control and readout from the log is done via

Ademco V-Link software only.

Alarm Output

• Provides a 12VDC, 2 AMP output that can drive the compatible

sounders listed in the EXTERNAL SOUNDERS section (

assumes a fully

charged battery is connected)

.

• Steady output for Burglary/Panic, or temporal pulse output (3 pulses –

pause – 3 pulses – pause – 3 pulses. . .) for Fire

• Uses current limiting circuitry for protection

Auxiliary Power Output

• Provides 12VDC, 600 mA maximum. Uses current limiting circuitry for

protection.

• This output interrupts for smoke detector reset if 4-wire smoke

detectors are used.

Programming

• Programmed options are stored in electrically erasable, non-volatile

EEROM memory (information can be reprogrammed at any time and

will not be lost in the event of a power loss).

• The system can be uploaded, downloaded, or controlled via an IBM

compatible computer, V-Link software and a HAYES modem specified

by Ademco.

Keypad programming consists of:

• Data field programming

• Interactive (menu) mode programming

For programming from a keypad, a 5137AD or 6139 2-line Alpha keypad

must be connected to partition 1 (but need not necessarily stay in the

system).

Communication Formats Supported

• Ademco Low Speed (Standard or Expanded)

• Sescoa/Radionics (Standard or Expanded)

• Ademco Express

• Ademco Contact ID

Zone Descriptors

You can assign Alpha descriptors to all zones (useful only when using

Alpha keypads and/or the 4285 Phone Module).

AC Power Supply

Uses 1321, 110VAC plug-in transformer with 16.5VAC 25VA output,

unless Powerline Carrier devices (ex. X-10 type) are used, in which case a

4300 transformer module must be used.

Back-Up Battery

• Rechargeable (Gel type) 12VDC, 4AH minimum.

WWW.DIYALARMFORUM.COM

–10–

Section 2. INSTALLING THE CONTROL

This section provides instructions for mounting the control cabinet, and

installing the cabinet lock (if used). Also included in this section are

instructions for the following:

• Installing the main PC board

• Mounting the 5881 (5882 in Canada) RF Receiver board in the cabinet (if

used)

• Standard phone line connections

• Installing the back-up battery in the cabinet

• Connecting the AC transformer

• Making earth ground connections

Mounting the Cabinet

Mount the control cabinet to a sturdy wall using fasteners or anchors (not

supplied), in a clean, dry area which is not readily accessible to the general

public. Four mounting holes are provided at the back of the cabinet.

If an RF Receiver is being used and you intend to mount its PC board within

the cabinet, note the following:

• Do not mount the cabinet on or near metal objects. This will decrease RF

range and/or block RF transmissions from wireless transmitters.

• Do not locate the cabinet in an area of high RF interference (revealed by

frequent or prolonged lighting of the LED in the receiver after it is

operational (random flicker is OK).

Installing the Lock (if used)

Use an Ademco No. N6277 Cam Lock and No. N6277–1 Push-On Clip

(Retainer Clip).

Note: The cabinet can be closed and secured without a lock by using 2

screws in the cover's edge.

CABINET DOOR BOTTOM

RETAINER

CLIP

RETAINER CLIP

(NOTE POSITION)

RETAINER

SLOTS

LOCKED

UNLOCKED

Figure 1. Installing The Cabinet Lock

1. Remove the cabinet door. It is

easily removable for servicing

and is easily re-installed.

2. Remove the lock knockout

from the control cabinet door.

Insert the key into the lock.

Position the lock in the hole

making certain that the latch

will make contact with the

latch bracket when the door is

closed.

3. Hold the lock steady, and

insert the retainer clip into

the retainer slots. Position the

clip as illustrated in order to

permit easy removal.

Before installing the cabinet's contents, remove the metal cabinet

knock-outs required for wiring entry. Do not attempt to remove the

knockouts after the circuit board has been installed.

WWW.DIYALARMFORUM.COM

–11–

Mounting The Control's Circuit Board Alone in The Cabinet (Fig. 2)

1. Hang two short Black mounting clips (provided) on the raised cabinet

tabs (see Detail B in Fig. 2).

2. Insert the top of the circuit board into the slots at the top of the cabinet.

Make sure that the board rests on the correct row (see Detail A ).

3. Swing the base of the board into the mounting clips and secure the board

to the cabinet with the accompanying screws (see Detail B in Fig. 2).

Figure 2. Mounting The PC Board

Mounting Control and RF Receiver Circuit Boards Together, in the Cabinet

1. Hang two short (black) mounting clips (provided with receiver) on the

raised cabinet tabs, as shown in Detail B in Figure 3.

2. Insert the top of the receiver board (removed from its own case as

described in its instructions) into the slots at the top of the cabinet, as

shown in Detail A in Figure 3. Make sure that the board rests on the

correct row of tabs, as shown.

3. Swing the base of the board into the mounting clips and secure it to the

cabinet with the accompanying screws (see Detail B in Fig. 3).

4. Insert the top of the control's board into the slot in the clips and position

two long (red) clips at the lower edge of the board (see Detail C).

5. Swing this board into place and secure it with two additional screws.

6. Insert grounding lugs (supplied with the receiver) through the top of the

cabinet into the left-hand terminals of the antenna blocks (at the upper

edge of the receiver board) and secure them to the cabinet top with the

screws provided, as shown in Detail D.

7. Insert the receiver's antennas through the top of the cabinet, into the

blocks' right-hand terminals, and tighten the screws.

8. Refer to the WIRELESS ZONE EXPANSION section for setup and wiring

of the receiver.

Figure 3. Mounting The PC Board And RF Receiver

Together In The Cabinet

WWW.DIYALARMFORUM.COM

–12–

Standard Phone Line Connections

The wiring connections shown here are not applicable if the 4285 Phone

Module is used. Refer to the 4285 Phone Module section for information

regarding phone line connections, which are different than those shown here.

Incoming phone line and handset wiring is connected to the main terminal

block (via a RJ31X jack) as follows (also see Figure 4):

Term. 21: Local Handset (TIP – Brown*)

Term. 22: Local Handset (RING – Gray*)

Term. 23: Incoming Phone Line (TIP – Green*)

Term. 24: Incoming Phone Line (RING – Red*)

* Colors of wires in Direct Connect Cord.

TERMINALS

ON CONTROL

EARTH GROUND

INCOMING TELCO LINE

➡

Handset

Incoming

Telco Line

TIP

RING

RJ31X

JACK

PLUG

DIRECT

CONNECT

CORD

➧

TIP

RING

GROUND

▲

▲▲

PREMISES

PHONES

▲

{

BROWN (TIP)

GRAY (RING)

GREEN (TIP)

RED (RING)

26 27 28 29 30

21 22

23 24

25

IMPORTANT!

IF THE PANEL IS NOT CONNECTED TO A PROPER

EARTH GROUND, YOU MAY GET FALSE TELEPHONE

LINE CUT INDICATIONS (IF THE TELEPHONE LINE

MONITOR HAS BEEN PROGRAMMED IN FIELD 92).

Figure 4. Telephone Line Connections

Wiring The AC Transformer

1321Wire the 1321 transformer to terminals 1 and 2 on the control board. See

wiring table below for wire gauge to use.

Caution must be taken when wiring the transformer to the control panel to

guard against blowing the fuse inside the transformer (the fuse is non-

replaceable).

4300 If you are going to use a 4300 transformer interface (required if Powerline

Carrier devices are going to be used), connect the 4300 transformer’s

terminals as follows:

a. Terminals 1, 3 (AC), and 2 (Ground) to control board terminals 1, 2, and

25, respectively (see Figure 5). See table below for wire gauge to use.

WIRING TABLE

Distance of Transformer Wire Gauge

From the Control Panel To Use

Up to 50 feet # 20

50–100 feet # 18

100-250 feet # 16

Wiring to the AC Transformer must not exceed 250 feet using 16 gauge wire.

The voltage reading between terminals 1 and 2 of the control must not fall

below 16.5VAC or an "AC LOSS" message will be displayed.

Do not plug the transformer into the AC outlet until you are instructed to do

so later in the manual.

WWW.DIYALARMFORUM.COM

–13–

b. Wire the other three terminals (Sync, Data, Com) on the 4300

transformer. Wires from these terminals must be connected to a 9-pin

connector on the control board (using a 4142TR cable supplied with the

4300 transformer), as shown in Figure 5. These particular wires can be

24 gauge or larger, and can be run along with the AC and ground wires

to the control panel.

123456789

9-PIN CONNECTOR

ON CONTROL BOARD

BLACK

BLUE

BROWN

GREEN

RED

WHITE

YELLOW

GRAY

VIOLET

4142TR CABLE

1

2

3

4

56

125 2

AC

Earth

Ground

AC

Sync

Data

Com

4300 TRANSFORMER/INTERFACE

TERMINALS

ON CONTROL

BOARD

THESE WIRES (7, 8, 9) NOT USED,

UNLESS 4146 KEYSWITCH

IS ALSO USED

Figure 5. Connections of 4300 Transformer To The Control Board

Installing The Back-Up Battery

If necessary, refer to FINAL POWER UP section for information regarding

battery size to use, etc.

Do not attach the connector cable to the battery terminals until you are

instructed to do so later in the manual.

1. Place the 12-volt back-up battery in the control cabinet.

2. Attach Red and Black wires on the battery connector cable as follows:

a. Red to the positive (+) battery terminal on the control board (see

Summary of Connections Diagram for location, if necessary).

b. Black to the negative (–) battery terminal on the control board.

U

L

Use a 4AH battery or larger for UL installations.

Earth Ground Connections

The designated earth ground terminal (25), must be terminated in a good

earth ground for the lightning transient protective devices in this product to

be effective. The following are examples of good earth grounds available at

most installations:

Metal Cold Water Pipe: Use a non-corrosive metal strap (copper is

recommended) firmly secured to the pipe to which the ground lead is

electrically connected and secured.

AC Power Outlet Ground: Available from 3-prong, 120VAC, power outlets

only. To test the integrity of the ground terminal, use a three-wire circuit

tester with neon lamp indicators, such as the UL-Listed Ideal Model 61–035,

or equivalent, available at most electrical supply stores.

WWW.DIYALARMFORUM.COM

–14–

Section 3. INSTALLING REMOTE KEYPADS

This section lists the wired keypads that may be used and provides

instructions for wiring and mounting the keypads.

A preliminary check-out procedure is also provided to ensure that the

connected keypads are functioning properly in the system.

Keypads That May Be Used

• Fixed-Word Display: 4137AD, 4127, 6127, 6128, 6137

• Alpha Display: 5137AD, 6138, 6139

• Up to 4 keypads in each partition (total of 8 in the system), independent of

auxiliary power considerations (you may need to use an auxiliary power

supply if the 600mA aux. output is exceeded)

If you are going to use a 4285 Phone Module, you MUST use addressable

keypads (4137AD, 5137AD, 6128, 6137, 6138, 6139) in the system, but set to

the non-addressable mode (address 31).

Wiring To The Keypads

1. Determine wire gauge by referring to the wiring length/gauge chart

below. Wire lengths/gauge for Partition 2 keypads should be determined

separately from those keypads connected to Partition 1.

For devices (Keypads, RF Receivers, Zone Expander , etc.) connected to a

single 4-wire run, determine the current drawn by all units connected to

the single wire run, then refer to the Wiring Run chart to determine the

maximum wire length that can be safely used for each wire size. Current

draw for all devices can be found in the SPECIFICATIONS AND

ACCESSORIES section.

Note: Refer to “Auxiliary Device Current Draw Worksheet” in the

FINAL POWER UP section for current draw for all keypads.

Maximum wire lengths for any device that is homerun to the control can

also be determined from the chart, based on the current draw of that device

alone.

Wiring Run Chart For Devices* Drawing Aux Power From

The Control (12V+ & 12V–)

TOTAL CURRENT DRAWN BY ALL DEVICES CONNECTED TO A SINGLE WIRE RUN

Wire Size 50 mA or less 100 mA 300 mA 500 mA 600 mA

#22 500 ft (152m) 250 ft (76m) 80 ft (24m) 50 ft (15m) 42 ft (13m)

#20 750 ft (228.6m) 380 ft (116m) 130 ft (39.6m) 80 ft (24m) 67 ft (20.4m)

#18 1300 ft (396m) 650 ft (198m) 220 ft (67m) 130 ft (39.6m) 115 ft (35m)

#16 1500 ft (457m) 1000 ft (305m) 330 ft (100.5m) 200 ft (70m) 170 ft (52m)

* Includes Keypads, RF Receivers, Zone Expander/Relay Units, or 4285 Phone Module.

The length of all wire runs for both partitions combined must not exceed

1500 feet (457m) when unshielded quad conductor cable is used (750 feet if

shielded cable is used). This restriction is due to the capacitive effect on the

data lines when quad cable is used.

2. Run field wiring from the control to the keypads (using standard 4-

conductor twisted wire cable using the wire gauge determined in step 1).

WWW.DIYALARMFORUM.COM

–15–

3. Connect remote Keypads for Partition 1 to terminals 4, 5, 6, and 7 on the

control board, as shown in Figure 6.

4. Connect remote Keypads for Partition 2 to the 4-pin connector on the

control board (see the Summary of Connections diagram for location of

the 4-pin connector for partition 2).

PARTITION 1 KEYPADS

BLACK

RED

GREEN

YELLOW

4

5

6

7

PARTITION 2 KEYPADS

N4632–5

CONNECTOR PINS FOR

PARTITION 2 ON CONTROL BOARD

CONTROL

TERMINALS

KEYPAD CONNECTOR CABLE (SUPPLIED WITH VISTA-20)

Figure 6. Keypad Connections To The Control Board

Mounting the Keypads

1. Make sure addressable type keypads (4137AD, 5137AD, 6128, 6137, 6138,

and 6139) are set to non-addressable mode (address 31), which is the

factory default setting. Refer to the instructions provided with the keypad

for address setting procedure.

2. Mount the keypads at a height that is convenient for the user. Refer to

the instructions provided with the keypad for mounting procedure.

You can either surface mount or flush mount keypads (using an

appropriate Trim Ring Kit: 5137TRK or 6139TRK). Refer to the mounting

instructions and template included with the keypad and/or trim ring kit

for specific information.

Using a Supplementary Power Supply to Power Additional Keypads

The control provides 600mA for powering keypads (up to a maximum of 4 per

partition) and other devices from the auxiliary power output. The backup

battery will supply power to these keypads in the event that AC power is lost.

When the control’s auxiliary power load for all devices exceeds 600 mA, you

can power additional keypads from a regulated, 12VDC power supply (e.g.,

487–12 supplies 12V, 250mA; 488–12 supplies 12V, 500mA). Use a UL

Listed, battery-backed supply for UL installations.

The 487–12/488–12 power supplies have a backup battery which can power

these keypads in the event of AC power loss.

Keypads powered from supplies which do not have a backup battery will

not function when AC power is lost. Therefore, be sure to power at least

one keypad in each partition from the Control's auxiliary power output.

Connect the additional keypads as shown in Figure 7, using the keypad wire

colors shown. Be sure to observe the current ratings for the power supply

used.

Make connections directly to the screw terminals as shown in Figure 7.

Make no connection to the keypad blue wire (if present).

Be sure to connect the negative (–) terminal on the Power Supply unit to

terminal 4 (AUX – ) on the control.

WWW.DIYALARMFORUM.COM

–16–

SUPPLEMENTARY

POWER SUPPLY

+

–

CONTROL

TERMINAL STRIP

AUX AUX. DATA DATA

– + IN OUT

4567

IMPORTANT:

MAKE THESE

CONNECTIONS

DIRECTLY TO

SCREW

TERMINALS AS

SHOWN.

TO KEYPAD RED WIRE

TO KEYPAD BLK WIRE

TO KEYPAD YEL WIRE

TO KEYPAD GRN WIRE

TO KEYPAD BLK WIRE

TO KEYPAD RED WIRE

TO KEYPAD GRN WIRE

TO KEYPAD YEL WIRE

Figure 7. Using A Supplementary Power Supply For Keypads

Preliminary Check-out Procedure

If you want to check that the system is working before connecting field wiring

from zones and devices, do the following:

1. Temporarily connect a 2000 ohm end-of-line resistor across each of the

basic hard-wire zones 1–8, as shown in the Summary of Connections

diagram.

Without actual zone wiring or EOL resistors connected, the keypads in

each partition of the system will not display the “Ready” message.

2. Power up the system temporarily by plugging the AC transformer

(previously wired to the control) into a 120VAC outlet.

3. Busy – Standby (Alpha keypads) or dI (Fixed-word keypads) will be

displayed.

After approximately 1 minute*, the green “READY” LED (or “POWER”

LED on some types of keypads) should light, and the word READY (Fixed-

word keypads), or DISARMED...READY TO ARM (Alpha keypads) should be

displayed.

* To bypass the 1-minute delay, press [#] plus 0.

If the “Ready” display does not appear on any of the keypads in the system

(in either of the partitions), or a “Not Ready” message is displayed, check

the keypad wiring connections, and make sure each of the 8 basic hard-

wired zones has a 2000 ohm resistor connected across its terminals.

4. When you get the proper “Ready” displays on the keypad(s), the system is

functioning properly at this point.

Do not remove the EOL resistors until you are ready to make connections

to the hard-wired zones, to allow for testing later in the manual.

If an OC or OPEN CIRCUIT is present on the keypad, data from the control

is not reaching the keypad. Please check the wiring.

WWW.DIYALARMFORUM.COM

–17–

Section 4. BASIC HARD-WIRED ZONES 1–8

This section provides general information for the hard-wired zones in the system, plus

specific instructions for installing 2-wire smoke detectors, 4-wire smoke/combustion

detectors, and 2-wire latching type glass break detectors.

Installing the Hard-Wired Zones

Common Characteristics for Zones 1–8

• Can be assigned to any partition

• EOLR supervised zones supporting both open circuit and closed circuit

devices

• As many 4-wire smoke detectors as can be powered from Aux Power on the

control (zones 2–7)

• Programmable for 10, 350, or 700 msec response

• 350 msec (default) should be used for most standard contacts. For

vibration type contacts, 10 msec is more suitable

Wiring Burglary and Panic Devices To Zones 1–8

1. Connect sensors/contacts to the hard-wired zone terminals (8 through 20).

See the Summary of Connections diagram .

2. Connect closed circuit devices in series in the high (+) side the loop. The

EOL resistor must be connected in series with the devices, following the

last device. See the Summary of Connections diagram.

3. Connect open circuit devices in parallel across the loop. The 2,000 ohm

EOLR must be connected across the loop wires at the last device.

If the EOLR is not at the end of the loop, the zone will not be properly

supervised, and the system may not respond to an open circuit on the zone.

High Resistance Supervision on Hard-Wired Zones 2–8

• Special supervision in the control senses high resistance on hard-wired

zone loops 2–8, causing a warning “CHECK” display with the affected zone

number to occur when the system is in the disarmed state. The system

cannot be armed when this display is present. If the system is in the

armed state when the high resistance condition occurs, no display will take

place until the system is disarmed.

Wiring 2-Wire Smoke Detectors To Zone 1

1. Connect 2-wire smoke detectors across zone 1 terminals 8 (+) and 9 (–).

Observe proper polarity when connecting the detectors.

2. If an EOL resistor is presently connected across zone 1 terminals, remove

it. The EOL resistor must be connected across the loop wires at the

last detector.

U

L

In UL installations, only zone 1 may be used as a Fire zone. In addition, an

Ademco Model 610–7 must be used as an End-of -Line resistor at the last

detector.

The alarm current provided by zone 1 will support only one smoke detector

in the alarmed state.

“Verify” Operation of

2-Wire Smoke Detectors

in Zone 1

The control panel will “verify” any alarm by resetting the smoke detectors

after the first alarm trigger, and then waiting 90 seconds for a second alarm

trigger. If the smoke detector or thermostat does not trigger again, the control

will disregard the first trigger, and no alarm signal will occur. This feature

eliminates false alarms due to electrical or physical transients.

This feature is available only on units that report to the downloader

as Rev 4 or higher.

WWW.DIYALARMFORUM.COM

–18–

Turning Off Fire Alarm

Sounding

You can turn off Fire alarm sounding by pressing the OFF key on any keypad or

other arming/disarming device in that partition. To clear the "memory of alarm"

and to reset the detector’s alarm, enter the security code plus OFF again.

COMPATIBLE 2-WIRE SMOKE DETECTORS

System Sensor

Detector Type Model No.

Photoelectric w/heat sensor,

direct wire 2300TB

Photoelectric, direct wire 2400

Photoelectric w/heat sensor,

direct wire 2400TH

Photoelectric 2451 w/B401B base

Photoelectric w/heat sensor 2451TH w/B401B base

Ionization, direct wire 1400

System Sensor

Detector Type Model No.

Ionization 1451 w/B401B base

Photoelectric duct detector 2451 w/DH400 base

Ionization duct detect 1451DH

w/DH400 base

Low-profile, Photoelectric,

w/135°F thermal 2100T

Low-profile, Ionization type,

direct wire 1100

2000 OHMS

EOLR

ZONE 1

SMOKE

+

–

2-WIRE SMOKE

DETECTOR

8

9

UL NOTE:

IN UL INSTALLATIONS, ONLY ZONE 1

MAY BE USED FOR FIRE.

Figure 8. 2-Wire Smoke Detector Connected to Zone 1

Wiring 4-Wire Smoke/Combustion Detectors on Zones 2–7

The system will support as many 4-wire detectors as can be powered from

Auxiliary Power on the control on zones 2–7. Refer to the detector’s

instructions for complete details regarding its proper installation and

operation.

1. Connect 12 volt power for the detectors from Auxiliary Power terminals 4

and 5, (which will interrupt power for fire alarm reset). Observe proper

polarity when connecting detectors.

2. Connect detectors (including heat detectors, if used) across terminals of

the zone selected (zones 2–7 may be used). All detectors must be wired in

parallel.

Remove 2000 ohm EOL resistor if connected across the selected zone

terminals. You must connect the EOL resistor across the loop wires at the

last detector.

3. To supervise power, we recommend the use of a System Sensor

No. A77-716B supervisory module.

AUX PWR

OUTPUT

TERMINALS

+

-

TO HI SIDE OF

SELECTED

ZONE

TO LO SIDE

OF SELECTED

ZONE

+

-

+

-

+

•

EOL

POWER

SUPERVISION

RELAY

MODULE

A77-716B

•

5

4

4-WIRE SMOKE

OR COMBUSTION

DETECTORS

2000

OHMS

EOLR

HEAT

DETECTOR

HEAT

DETECTOR

ZONES 2–7

*

+

–

REDBLK

VIOLET

* IF PROGRAMMED FOR FIRE

Figure 9. 4-wire Smoke Detector Connections (Zones 2–7)

WWW.DIYALARMFORUM.COM

–19–

COMPATIBLE 4-WIRE SMOKE/COMBUSTION DETECTORS

1412 System Sensor, 4-wire ionization products of combustion

detector

2412 System Sensor, 4-wire photoelectric smoke detector

2412TH System Sensor, 4-wire photoelectric smoke detector

w/135º F (57º C) heat detector

A77–716B System Sensor, EOL relay module (supervisory module for

wired 4-wire fire zone).

2112/24T System Sensor low-profile 4-wire photoelectric smoke

detector w/135º F (57º C) heat detector

Wiring 2-Wire Latching Glass Break Detectors On Zone 8

Use zone 8 for connection of compatible 2-wire latching-type glass break

detectors.

After an alarm, the first code + OFF turns off the siren and disarms the

system; the second code + OFF clears the memory of alarm and resets the

glassbreak detector.

1. Connect all detectors in parallel across zone 8 (terminals 19 and 20).

Remove 2000 ohm EOL resistor if connected across the selected zone

terminals. You must connect the EOL resistor across the loop wires at the

last detector.

Compatible Glass Break Detectors

Use detectors that meet the following ratings:

Standby Voltage: 5VDC–13.8VDC

Standby Resistance: Greater than 20k ohms (equivalent resistance of all

detectors in parallel)

Alarm Resistance: Less than 1.1k ohms (see note below)

Alarm Current: 2 mA–10 mA

Reset Time: Less than 6 seconds

The IEI 735L series detectors have been tested and found to be compatible

with these ratings. You can use up to fifty IEI 735L detectors, connected in

parallel.

You should note that only one detector in the alarmed state can be

supported by the alarm current provided by zone 8.

You can use detectors which exceed 1.1k ohms in alarm, provided they

maintain a voltage drop in alarm of less than 3.8 volts.

Do not use other N.O. or N.C. contacts when using glass break detectors on

zone 8. Other contacts may prevent proper glass break detector operation.

2000

OHMS

EOLR

ZONE 8

LATCHING TYPE GLASS

BREAK DETECTOR LOOP

19

20

(+)

(–)

GLASSBREAK

DETECTOR

Figure 10. Glass Break Detector Connections To Zone 8

WWW.DIYALARMFORUM.COM

–20–

Programming Hard-Wired Zones

Each zone must be programmed into the system using the *56 Zone

Programming mode, which assigns characteristics that define the way the

system responds to faults on that zone. Refer to the Zone Response Type

section and the Zone Programming section for specific instructions on

programming hard-wired zones.

Check-Out Procedure For Hard-Wired Zones

After installation and programming of all hard-wired devices is completed,

each partition of the security system should be checked, as follows.

1. Make certain that all devices and sensors connected to the hard-wired

zones are not in a faulted state. Doors and windows with contacts should

be closed, PIRs should be covered (use a cloth to mask them temporarily if

necessary).

2. Plug in the AC Transformer if you have not already done so.

3. With all hard-wired zones intact, the Alpha keypad connected to the

system should display:

DISARMED

READY TO ARM.

If the following is displayed,

DISARMED Press

✱

to show faults

press the [

✱

] key to display the faulted zone(s). Restore any faulted

zone(s) as necessary (also make sure that you have connected a 2000 ohm

EOL resistor across the terminals of unused zones).

When the DISARMED...READY TO ARM message is displayed, you can

proceed to the next step.

4. Fault and then restore every contact or sensor on each zone individually to

ensure that it is being monitored by the system. Each time a zone is

faulted, the keypad should display the number of the faulted zone. When

each zone is restored, the READY TO ARM message should appear again.

If some hard-wired zones have been assigned to partition 1 and others to

partition 2, you will need to observe the keypad in the appropriate

partition as each zone in that partition is faulted and restored.

5. When you get the proper displays on the keypad(s), the hard-wired zones

in the system are functioning properly.

6. Unplug the AC transformer.

WWW.DIYALARMFORUM.COM

Page is loading ...

ADEMCO VISTA-20HWse Installation Instructions Manual

This manual is also suitable for

ADEMCO VISTA-20HWse Installation Instructions Manual

Related papers

Other documents