Pentek PENTEK-150574 User manual

Brand: Pentek

Model: PENTEK-150574

Category: Sanitary ware

Type: User manual

Water Filter

Installation and Operating Instructions

Specifications

Tools Required

Screwdriver File Pipe Cutter or Hacksaw

2 Adjustable Wrenches Pencil

Materials Required

Depends on type, size, and location of pipe on which system will be installed. See instructions that relate to your

particular installation, or consult your local hardware store or plumbing supplier to find out more about your particular

installation needs.

Precautions

WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection

before or after the system.

CAUTION: Filter must be protected against freezing, which can cause cracking of the filter and water leakage.

CAUTION: The rubber o-ring provides the water-tight seal between the cap and the bottom of the housing. It is important

that the o-ring be properly seated in the groove below the threads of the housing, or a water leak could occur.

CAUTION: To prevent costly repairs or possible water damage the sump of plastic housings must be replaced every five

years for clear, and ten years for opaque. If sump is older than recommended, replace immediately. Date sump for reference

and indicate replacement date.

• Install on cold water line only.

• Do not install where system will be exposed to direct sunlight.

• Make certain that installation complies with all state and local laws and regulations.

• For prolonged periods of non-use (such as during a vacation), it is recommended that the system be flushed

thoroughly. Let water run for 5–6 minutes before using.

• The filter cartridge has a limited service life. A decrease in water flow indicates that the cartridge should be

replaced.

• Some harmless bacteria will attack cellulose media cartridges. If your cartridge seems to disintegrate or has a musty

or moldy odor, switch to a synthetic media cartridge or consult the cartridge manufacturer.

Filter Housing Temperature Range Pressure Range Optional Accessories

3/4-inch I/O 40–125°F (4.4–51.7°C) 30-125 psi (2.1-8.62 bar) Mounting Bracket (151011)

Spanner Wrench (150295)

1/4, 3/8, 1/2-inch 40–125°F (4.4–51.7°C) 30-125 psi (2.1-8.62 bar) Mounting Bracket (244047)

I/O Spanner Wrench (150539)

1-inch, 1-1/2-inch 40–100°F (4.4–37.8°C) 30-100 psi (2.1-6.89 bar) Mounting Bracket (150062)

I/O Spanner Wrench (150296)

Whole House Installation

(1/2 inch or 3/4-inch main cold water line)

Materials Required:

(2) 3/4-inch or 1/2-inch NPT compression fittings

Teflon

tape

Reducing adapters (if necessary)

NOTE:

• Reducing adapters can be used to adapt the filter to different pipe sizes. See your local

hardware store or plumbing store for help in selecting the necessary adapters and com-

pression fittings for your installation needs.

• Galvanized fittings must be used with installation on galvanized pipe.

• Filter must be installed after water meter or pressure tank.

1. Turn off cold water supply and open nearest faucet to drain pipes before starting instal-

lation. Wrap about 6 inches of Teflon

tape in clockwise direction around pipe threads

of each compression fitting.

2. If mounting bracket (not supplied) is to be used, first use bracket as a template to mark

screw locations. Then place bracket over cap and align with inlet and outlet ports. Allow

2 inch clearance below housing to enable cartridge changes.

NOTE: Mounting bracket for heavy-duty filter does not fit over inlet/outlet connec-

tions. Heavy-duty bracket should be screwed directly into cap or filter.

3. Start compression fittings into cap by hand and use a wrench to tighten firmly. DO NOT

OVERTIGHTEN. About one thread should remain visible. Remove compression nuts from

fittings.

4. Measure length (shown as X on Figure 4) across assembled fittings and subtract 1 inch

if you are installing on 3/4-inch pipe or 1

2 inches if you are installing on 1/2-inch pipe.

Mark section of pipe to be removed.

5. Use a pipe cutter or hacksaw, cut pipe and remove marked section of pipe. File or sand

sharp edges on remaining pipe.

6. Slip compression nut and ferrule onto each end of pipe.

7. Align filter assembly with ends of pipe, making certain cap opening marked “IN” is fac-

ing your incoming water supply. It will be necessary to spread ends of pipe apart to

install filter assembly. Using two adjustable wrenches, hold incoming adapter securely

with one wrench and tighten nut with second wrench. Repeat process for outgoing

adapter.

8. Slowly turn on the water supply to allow filter to fill with water, then press the red pres-

sure-relief button on top of filter to release trapped air. Open nearest faucet and flush

water through cartridge for 5 minutes. Check for leaks before leaving installation.

9. CAUTION: If water pipes are used to ground electrical systems, appliances, or

phones, be certain to install a jumper wire. Contact a qualified electrician with any

questions about your home’s electrical system.

OUT

Undersink Installation

(3/8-inch cold water line)

Materials Required:

Teflon

tape

Plastic tubing

(2) 3/8-inch compression fittings

(2) 3/8-inch compression elbows (with ferrules and tubing inserts)

(2) 3/8-inch to 3/4-inch NPT reducing adapters (for installation of 3/4-inch I/Os / filters)

NOTE:

• Reducing adapters can be used to adapt the filter to different pipe sizes. See your local

hardware store or plumbing store for help in selecting the necessary adapters and com-

pression fittings for your installation needs.

1. Turn off cold water supply and open nearest faucet to drain pipes before starting instal-

lation. Place a tray or towel under the cold water line to catch excess water. Wrap about

6 inches of Teflon

tape in clockwise direction around pipe threads of each fitting /

adapter.

2. Attach the mounting bracket:

3/4-inch filters–see #2 under Whole House Installation

3/8-inch filters–using the self-tapping screws, attach mounting bracket to cap.

Mark location under sink where filter is to be mounted. Allow

inches under filter to

enable cartridge changes.

3. Assemble fittings/adapters. Start fitting/adapter into inlet of cap by hand, then tighten

with a wrench. DO NOT OVERTIGHTEN. About one thread should remain visible. Repeat

for outlet on filter cap.

4. Using a pipe cutter or hacksaw, remove a 3-inch section of pipe from the cold water line.

Deburr ends of remaining pipe with a file.

5. Determine the lengths of tubing needed to connect the inlet and outlet sides of the filter

to compression elbows on the cold water line. Measure tubing short enough to prevent

kinking. Using two wrenches, tighten compression nuts 1

2- to 2-turns.

6. Turn on water supply to allow filter to slowly fill with water, then press the pressure-

relief button on the housing to release trapped air. Open faucet and flush filter with

water for 5-minutes. Check for leaks and tighten fittings as needed.

Cartridge Replacement

A. Turn off water supply to filter. Depress red pressure-relief button to relieve the pressure,

then twist off bottom of housing.

NOTE: If turning off water supply to filter will also turn off water supply to the rest of

the home, be sure to fill a bucket of water first to allow you to clean housing after it has

been removed.

B. Locate and remove large o-ring, wipe clean of lubricant, and set aside.

Discard used cartridge. Rinse out bottom of housing and fill about 1/3 full with water.

Add about 1 tablespoon of bleach and scrub cap and bottom of housing with nonabra-

sive sponge or cloth. Rinse thoroughly.

Lubricate o-ring with clean silicone grease. Clean groove and connection point on cap.

Insert o-ring back into groove and smooth into place with finger.

Insert new cartridge over standpipe in bottom of housing.

C. Screw bottom of housing onto the cap and hand-tighten. DO NOT OVER-TIGHTEN.

Make certain cap standpipe slips into cartridge.

Slowly turn on the water supply to allow filter to fill with water and then press the red

pressure-relief button on top of the filter to release trapped air. Open faucet and flush

filter with water for 5-minutes. Check for leaks before leaving installation.

3”

cold water

line

nut

ferrule

elbow

OUT

Scale & Coarse Sand, Dirt, Fine sand, Extra-fine sand,

rust particles sand silt dirt, silt dirt, silt

P5 5 micron nom. Spun Polypropylene 10 gpm/<1 psi 2 mo. ••• ••

CP-5 5 micron nom. Pleated Cellulose/Poly 10 gpm/< 1psi 2 mo. ••• ••

CW-F 10 micron nom. Cord-Wound 7 gpm/< 1 psi 3 mo. ••• •

S1 20 micron nom. Pleated Cellulose 10 gpm/< 1 psi 4 mo. •••

CW-MF

30 micron nom. Cord-wound 10 gpm/< 1 psi 3 mo. •••

R30 30 micron nom. Pleated polyester 12 gpm/< 1 psi 4 mo. •••

R50 50 micron nom. Pleated polyester 12 gpm/< 1 psi 4 mo. ••

Troubleshooting

Leaks…Between cap and bottom of housing:

1. Turn off water supply and press the red pressure-relief button.

2. Clean and lubricate o-ring if necessary, then screw bottom of housing

onto cap and hand-tighten. DO NOT OVER-TIGHTEN.

Mfg. By Pentair Water Treatment ® 2003

145817 Rev B 10/03

WARRANTY

Pentek warrants to the original owner (under normal use): all products and parts to be free from defects in material and workmanship for a period of one (1) year. Notwithstanding the foregoing, (a) the warranty period for sumps shall be a period of five (5) years. Any

replacement products furnished will be free from defects in material and/or workmanship for the remainder of the original warranty period, or 30 days, whichever is longer. This warranty does not cover: (1) cartridges, media, and accessories (2) defects not reported

within the above time period, (3) items manufactured by other companies, (4) problems arising from failure to comply with Pentek instructions, (5) problems and/or damage arising from acts of nature, abuse, misuse, negligence or accident by any party other than Pentek,

(6) problems and/or damage resulting in whole or in part from alteration, modification, repair or attempted alteration, modification or repair by any party other than Pentek, (7) noncompliance with applicable codes/ordinances. If a defect in workmanship and/or material

in a product or part covered by the warranty should arise, Pentek, at its sole discretion, will repair or replace the defective product or part (Pentek may consider, in good faith, the customer's preference).

All claimed defective product must: (1) be authorized for return by Pentek with an RGA number (2) include proof of the purchase date of the product or part (3) returned to Pentek prior to the expiration of the warranty date, at the customer's expense, shipment pre-paid,

(4) be accompanied by a letter detailing the Model Number, Serial Number (if any), and a brief description of the problem. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, PENTEK DISCLAIMS ALL OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED,

INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WITH REGARD TO THE PRODUCTS, PARTS AND ANY ACCOMPANYING WRITTEN MATERIALS.

To the maximum extent permitted by applicable law, Pentek shall not be liable for any damages whatsoever (including, but not limited to, loss of time, inconvenience, expenses, labor or material charges incurred in connection with the removal or replacement of the

products or parts, special, incidental, consequential, or indirect damages for personal injury, loss of business profits, business interruption, loss of business information, or any other pecuniary loss) arising out of the use of or inability to use the defective products or parts,

even if Pentek has been advised of the possibility of such damages. Penteks' maximum liability under any provision of this Limited Warranty shall be limited to the amount actually paid for the products or parts. NOTE: Because some states do not allow the exclusion or

limitation of incidental or consequential damages, the above limitations or exclusions may not apply. THIS WARRANTY GRANTS SPECIFIC LEGAL RIGHTS, AND OTHER RIGHTS MAY APPLY. SUCH RIGHTS VARY FROM STATE TO STATE.

PENTEK FILTRATION

502 Indiana Avenue • Sheboygan, WI 53081

Toll Free Technical Support: 800-861-8758 • Technical Support: 920-451-9301 • [email protected]

Phone 920-457-9435 • www.pentekfiltration.com

International Fax: 920-457-2417 • [email protected]

Chlorine

Bad Taste Sediment

Taste & Odor

C1 5 micron nom. Carbon-impregnated 5 gpm/2 psi 3 mo. • • •

Cellulose

CC-10 — Granular Activated Carbon 1 gpm/3 psi 6 mo. • •

(coconut-shell)