Noble House 302247 Operating instructions

Type
Operating instructions

This manual is also suitable for

Label Picture Description QTY
A Left Armrest / Leg 1
B Right Armrest / Leg 1
C Seat 1
D Seat Back 1
Caution: You must read this before you proceed
Single Chair
Label Picture Description QTY
E Allen Key 1
F
Bolt
(
M6*30mm
)
5
G
Bolt
(M6*40mm)
3
H
Bolt
(M6*60mm)
3
I Washer 13
J Seat Cushion 1
K
Bolt
(
M6*20mm
)
2
L Connection 1
M Connection 1
Before Beginning Assembly:
Step 1
Step 2
Open the carton and place all the parts on a clean, non-marring surface.
ATTENTION: Occasionally some of the PE Wicker shifts and covers the mounting
positions preventing easy assembly.
The PE wicker should never be cut, but moved away from the mounting positions.
Attach Left Armrest / Leg(A) to the Seat(C) using Bolt(F) and Washer(I) with Allen Key(E)
as shown in the picture above.
Loosely tighten the Bolts.
Attach Seat Back(D) to Seat(C) using Washer(I) , Bolt(G&K) &Connection(L&M) with
Allen Key(E) as pictured above.
Loosely tighten the Bolts.
Step 4
Connect the Chair Legs(A&B) with the Seat Back(D) using Washer(I) and Bolt(H) with
Allen Key(E) as pictured above.
Loosely tighten the Bolts.
Step 3
Attach Right Armrest / Leg(B) to Seat(C) using Bolt(F) and Washer(I) with Allen Key(E ) as
shown in the picture above.
Loosely tighten the Bolts.
Place the Seat Cushion(J) on the Chair.
Your Chair is ready for use.
Step 5
Check for stability and then tighten all Bolts at all joints.
Note: DO NOT fully tighten a Bolt in one go and then move on to the next.
Rather; in a sequential manner, gradually tighten each Bolt until all Bolts are evenly
secured.
This methodology will ensure maximum evenness once all Bolts are fully tightened.
Step 6
Page 1 of 9Page 1 of 9Page 1 of 9
Caution : You must read this before you proceed
TABLE
CAUTION: This Table is NOT a TOY.
Keep your child / children at bay during the assembly process.
For moving the Table and to prevent damage to the Table, two adults
are needed to execute this action.
Noble House Home Furnishings LLC
Page 2 of 9Page 2 of 9Page 2 of 9
Label Picture Description QTY
A Table Top 1
B Iron Leg 2
C Support Bar 2
D Side Turnbuckle Set 2
E Bottom Turnbuckle Set 1
Label Picture Description QTY
1 Short Bolt (M8x20mm) 17
2 Washer 17
Long Bolt (M6x45mm) 3
Screw (M6x50mm) 13
Allen Key 2
1
2
3
4
5
6
Sleeve Nut (M6x20mm) 3
Noble House Home Furnishings LLC
Page 3 of 9Page 3 of 9Page 3 of 9
Before Beginning Assembly:
Noble House Home Furnishings LLC
Page 4 of 9Page 4 of 9Page 4 of 9
OVERVIEW
Iron Leg (B)
Side Turnbuckle
Set (D)
Table Top (A)
Iron Leg (B)
Side Turrnbuckle
Set (D)
Bottom
Turnbuckle Set (E)
Step 1
This Table has multiple parts and may require up to some 30 minutes to
assemble. To give you an overview of the Table parts, the above picture
is to help you put the various parts into perspective. Please read
through the instructions below to familiarise yourself with the parts and
steps before assembly.
FRONT FACING
Iron Leg (B)
Unpack and place all parts on a clean, non-marring surface.
Noble House Home Furnishings LLC
Page 5 of 9Page 5 of 9Page 5 of 9
Step 2
Step 3
2.1) Connect the Side Turnbuckle Sets(D) together as shown in the
arrow above
2.2) Connect the Bottom Turnbuckle Set(E) together as shown in the
arrows above
Step 3.1
Step 2.1
Step 2.2
3.1) With the assistance of an adult helper, unfold the Table Top(A) as
shown.
3.2) Then lay the Table Top (A) facedown onto a clean, flat surface to
Step 3.1
Step 3.2
A
3.2) Then lay the Table Top (A) facedown onto a clean, flat surface to
avoid any scratches or damage to the product.
Noble House Home Furnishings LLC
Page 6 of 9Page 6 of 9Page 6 of 9
Step 4
Align Support Bar(C) to the housings on Table Top(A) and secure using
Screws() with Allen Key().
Only loosely tighten the Screws.
C
A
6
4
housings
Step 5
Only loosely tighten the Screws.
Repeat the same process with the other Support Bar(C).
Attach Iron Leg(B) to Table Top(A) using Short Bolt(
) and Washer(
) with
Allen Key(
).
Notice: The leg with hole should be face inside against
A
B
6
1
2
Notice: The leg with hole should be face inside against
Only loosely tighten the Bolts.
Repeat the same process with the other Iron Leg(B)
Noble House Home Furnishings LLC
Page 7 of 9Page 7 of 9Page 7 of 9
Step 6
Place Side Turnbuckle Set(D) between housing of Table Top(A) and Iron Leg(B).
Attach Side Turnbuckle Set(D) to Iron Leg(B) using Short Bolt(
) and
Washer() with Allen Key()
1
2
6
D
B
A
Step 7
Affix Side Turnbuckle Set(D) to Table Top(A) using Long Bolt(
) and Sleeve
Nut() with Allen Key().
Washer() with Allen Key()
Only loosely tighten the Bolts.
Repeat the same process with the other Side Turnbuckle Set(D).
6
6
5
3
D
A
Nut() with Allen Key().
Only loosely tighten the Bolts.
Noble House Home Furnishings LLC
Page 8 of 9Page 8 of 9Page 8 of 9
Step 8
Attach the Bottom Turnbuckle Set(E) to Iron Legs(B) using Short Bolt() and
6
1
2
E
Step 9
Attach the Bottom Turnbuckle Set(E) to Iron Legs(B) using Short Bolt() and
Washer(
) with Allen Key(
).
Only loosely tighten the Bolts.
Stand the Table right side up.
Inspect it and make sure all parts are adequately connected.
In a sequential manner, tighten all Bolts and Screws until fully locked into position.
Notice: By hand, turn the Side Turnbuckle Sets (D) and Bottom Turnbuckle Set(E)
to fixed point on Turnbuckle Sets (D), (E) to further secure the Table and
maximize stability and show the Turnbuckle Sets as place as the picture.
maximize stability and show the Turnbuckle Sets as place as the picture.
Your Table is ready for use.
This Table can only be used on a flat, level surface.
Noble House Home Furnishings LLC
Page 9 of 9
OUTDOOR
Noble House Home Furnishings LLC
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15

Noble House 302247 Operating instructions

Type
Operating instructions
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI