RailKing 30-4244-1 User manual

Brand: RailKing

Model: 30-4244-1

Type: User manual

This manual is also suitable for

30-4245-1

READY-TO-RUN

Sets

THE COMPLETE SOLUTION

2-8-0 STEAM FREIGHT/

PASSENGER SET

OPERATION MANUAL

PLEASE READ BEFORE USE AND SAVE

www.mthtrains.com

RAILKING

2-8-0 STEAM FREIGHT READY-TO-RUN

™

SET W/PROTO-SOUND

3.0 1

Four Ways to Operate Your Proto-Sound 3.0 Equipped Train Set .............................................................................2

Set Up Checklist .............................................................................................................................................. 3

Model Train Terms ........................................................................................................................................... 4

Getting Started ................................................................................................................................................. 5

Assembling RealTrax ............................................................................................................................ 5

Lubricating the Engine .......................................................................................................................... 5

Priming the Smoke Unit ........................................................................................................................ 6

Coupling the Engine and Cars .............................................................................................................. 6

Placing the Engine on the Track ............................................................................................................ 7

Connecting the Tranformer & Installing DCS Explorer ..................................................................................................8

DCS Explorer Explained .......................................................................................................................................9

Download and Install the DCS App .......................................................................................................................10

Using the MTH Network ....................................................................................................................................................11

Using your HOME Wi-Fi Network .....................................................................................................................................12

For Routers with WPS (WiFi Protected Setup) ..................................................................................................... 12

Routers that Require Manual Set-up (no WPS feature) ........................................................................................ 12

Using a Wired Ethernet Network ......................................................................................................................................14

LuCI (Web Interface) ..........................................................................................................................................................15

Accessing LuCi ..................................................................................................................................................... 15

Updating DCS Explorer Firmware ......................................................................................................................... 16

Changing the SSID and Network Key for MTH Wi-Fi Network Mode ................................................................... 19

APP Tour ............................................................................................................................................................................ 21

Title Screen ...........................................................................................................................................................21

Main Control Screen ............................................................................................................................................. 22

Engine List Screen ................................................................................................................................................ 23

Adding New Engines ............................................................................................................................................. 24

Seondary Control Screen ...................................................................................................................................... 25

Settings Screen ..................................................................................................................................................... 28

Navigational Tips ................................................................................................................................................... 30

Troubleshooting .................................................................................................................................................... 32

Maintenance ......................................................................................................................................................33

Lubrication and Greasing Instructions ....................................................................................................33

Cleaning the Wheels, Tires and Track ....................................................................................................34

Traction Tire Replacement .....................................................................................................................35

ProtoSmoke™ Unit Operation ................................................................................................................36

LED Lighting ..........................................................................................................................................37

Headlight Replacement ..........................................................................................................................38

RailWare Interactive DVD..................................................................................................................................40

Service and Warranty Information ....................................................................................................................41

CAUTION: ELECTRICALLY OPERATED PRODUCT:

Recommended for Ages 14 and up. Not recommended for children under 14 years of age without adult supervision.

As with all electric products, precautions should be observed during handling and use to prevent electric shock.

WARNING: When using electrical products, basic safety precautions should be observed, including the following:

• Read this manual thoroughly before using this device.

• M.T.H. recommends that all users and persons supervising use examine the hobby transformer and other electronic equipment

periodically for conditions that may result in the risk of re, electric shock, or injury to persons, such as damage to the primary

cord, plug blades, housing, output jacks or other parts. In the event such conditions exist, the train set should not be used until

properly repaired.

• Do not operate your layout unattended. Obstructed accessories or stalled trains may overheat, resulting in damage to your

layout.

• This train set is intended for indoor use. Do not use if water is present. Serious injury or fatality may result.

• Do not operate the hobby transformer with damaged cord, plug, switches, buttons or case.

• The transformer was designed to operate on regular US household current (120 volt, 50-60 Hertz). Do not connect to any other

source of power.

• To avoid the risk of electrical shock, do not disassemble the transformer unit. There are no user-serviceable parts inside. If the

unit is damaged contact M.T.H. Service for instructions.

• The transformer is equipped with an internal circuit protector. If the circuit protector trips, unplug the power cord from the

electrical wall outlet, check your layout for any short circuits. The circuit breaker will reset automatically when the short is

removed from the circuit.

• Unplug the transformer from the electrical wall outlet when not in use.

• Do not use this transformer for other than its intended purpose.

Transformer Ratings: Input: 120 VAC, 60 Hz Only, Output: 15 VDC, 56.3 VA

This product may be protected by one or more of the following patents:

6,019,289; 6,280,278; 6,281,606; 6,291,263; 6,457,681; 6,491,263; 6,604,641; 6,619,594; 6,624,537; 6,655,640.

TABLE OF CONTENTS

RAILKING

2-8-0 STEAM FREIGHT READY-TO-RUN

™

SET W/PROTO-SOUND

3.0 2

4 WAYS TO OPERATE YOUR PROTO-SOUND 3.0

EQUIPPED TRAIN SET:

DCS Explorer:

Your RailKing Ready-to-Run Train Set features an industry-leading range of operating features that

can be operated in ways no other modern train set can emulate. The included DCS Explorer and

power supply in your set pairs with YOUR smart phone or tablet to give you fast, wi-enabled control

over the locomotive in a simple intuitive interface.

Other DCS Control Options:

Don’t have a smart device? Swap out the DCS Explorer for simple infra-red control using the DCS

Remote Commander, or choose the 32 digital function DCS Commander or even the full featured

DCS System for the ultimate in command control technology. You can learn more about command

control and DCS options by visiting our DCS Options page at www.mthtrains.com/2017RTRsets/DCS.

DCC Command Control:

Similar to the M.T.H. DCS systems, DCC is an older industry standard command control protocol that

sends digital signals to the train. While not as robust or intuitive as DCS, DCC control is an appealing

option for customers who already have DCC equipped trains. DCC controllers are available from

many dierent manufacturers. Your train set locomotive requires a slight, do-it-yourself modication

to work under DCC control. Instructions for modifying the locomotive and operating it under DCC

control can be found by visiting our DCC Control page at www.mthtrains.com/2017RTRsets/DCC.

Conventional AC or DC Analog Control:

Virtually any AC or DC traditional transformer can run your Proto-Sound 3.0 train set providing speed,

direction and basic locomotive sounds. AC transformers with whistle and bell controls can access

additional features whistle and horn eects, bell sounds, coupler operation and much more. Learn

more and see a list of compatible transformers by visiting our Conventional Control Options page at

www.mthtrains.com/2017RTRsets/conventional.

Manual Volume Control

To adjust the volume of all of the sounds made by the engine

(while operating the engine in CONVENTIONAL AC OR DC

ANALOG CONTROL), turn the manual volume control (see

gure) clockwise to increase the volume and counterclockwise

to reduce the volume. Turning the manual volume control

completely counterclockwise will turn o all of the engine sounds

and announcements.

Manual Volume Control

RAILKING

2-8-0 STEAM FREIGHT READY-TO-RUN

™

SET W/PROTO-SOUND

3.0 3

• Assemble RealTrax

• Lubricate the engine

• Prime the Smoke Unit

• Place the engine and cars on the track and couple them together

• Connect the transformer and install the DCS Explorer

• Apply power to run as described in the Basic Operation section of these

instructions

Set Includes:

• Steam Engine

• 3 Cars

DCS Explorer

(50-1035)

8-Pieces O-31 Curve

RealTrax (40-1002)

4-Pieces Straight

RealTrax

(40-1001)

RealTrax wire

harness (40-1015)

Lighted Lock-On

(40-1003)

DCS Explorer

Power Supply

DVD

Tools Needed

Philips Screwdriver

Pliers

Scissors

Cotton Swab or Rag

M.T.H. Maintenance Kit

(30-50051)

You can obtain replacement parts and replacement instructions from the

M.T.H. Parts Department

(Order Online: www.mthtrains.com,

E-mail: [email protected], Fax: 410-423-0009, Phone: 410-381-2580,

Mail: 7020 Columbia Gateway Drive, Columbia MD 21046-1532)

SET UP CHECKLIST

RAILKING

2-8-0 STEAM FREIGHT READY-TO-RUN

™

SET W/PROTO-SOUND

3.0 4

PS3 - ProtoSound 3.0. This refers to the electronics in the engine. PS3.0 equipped loocomotives

operate in Conventional mode; DCS Command Mode, and DCC.

DCS - Digital Command System. MTH’s propietary command system.

DCC - Digital Command Control. This system meets NMRA Standards and is manufactured by other

companies.

Conventional Mode - Refers to conventional operation whereby track voltage is varied to change the

speed of the train.

Command Mode - refers to digital command operation where a constant voltage is placed on the

track and digital signals are sent to specic locomotives via the track to control the locomotives

speed, lights, and sounds.

At the end of an operational session, disconnect the transformer from the wall outlet.

NOTE: Power is sent to the track when the transformer is plugged into the wall outlet. Remove the

plug from the wall outlet when not in use to eliminate power to the track.

MODEL TRAIN TERMS

RAILKING

2-8-0 STEAM FREIGHT READY-TO-RUN

™

SET W/PROTO-SOUND

3.0 5

Assembling RealTrax

The quick connectors and built-in roadbed allow you to set up RealTrax anywhere, including carpeted

surfaces.

Lubricating the Engine

Lubricate all exposed moving parts before operating using a multi-purpose, plastic-compatible oil

(available with M.T.H.'s Maintenance Kit (#30-50010) , sold separately) or a light household oil.

Follow the lubrication points.

Knock-out must be

removed before remote

lock-on can be installed

Remove knock-out from

outer edge of track by

holding and twisting up

with a pair of pliers

Insert lock-on into

knock-out tab

(Lock-on is the

interface between

the track and

transformer)

Make sure the metal

contacts line up.

Align Quick Con-

nect Plugs

Gently push

together RealTrax

Figure: Lubrication Points on the Locomotive

GETTING STARTED

For more information on assembling and using RealTrax, visit www.mthtrains.com/RTRsets

and click on the RealTrax video link.

RAILKING

2-8-0 STEAM FREIGHT READY-TO-RUN

™

SET W/PROTO-SOUND

3.0 6

Coupling the Engine and Cars

1) Position armiture for proper operation.

2) Place the engine and cars on the track. Open couplers by pressing down on plunger.

Figure: Coupling the Engine and Cars

Priming the Smoke Unit

You should prime the smoke unit with smoke uid before operating. Add 15-20 drops of smoke uid

from the included pipette through the smokestack, then gently blow into the stack to eliminate any

air bubbles in the uid. If you choose not to prime the unit with uid, turn the smoke unit control see

illustration to the OFF position (full counter clockwise position). Running the engine without a

primed smoke unit may cause damage. See the “ProtoSmoke™ Unit Operation” section of this

book for more information on smoke unit maintenance.

Add 15-20 Drops

Smoke Fluid

Smoke Unit Control

Running the engine without primed

smoke unit may cause damage

RAILKING

2-8-0 STEAM FREIGHT READY-TO-RUN

™

SET W/PROTO-SOUND

3.0 7

Placing The Engine On The Track

Your MTH steam engine is equipped with a tetherless drawbar. There is no unsightly cable or box

showing between the engine and the tender to detract from the appearance of the model. The

electrical connections pass through conductors in the drawbar, so it is important that the connector

be properly inserted. The connector is xed to the rear end of the drawbar. The mating connector is

attached to a swivel connection on the front of the tender frame. The drawbar is connected to the

engine chassis with a screw and should not need any attention.

In order to mate the connectors of the drawbar and the tender, place the engine and the tender on

the track. Position the tender over the drawbar connector and insert the drawbar pin on the swivel

connector into the hole in the drawbar.

Now grasp the tender with both hands as shown below and place a nger on each side of the

drawbar near the connector. Now using your ngers, push the connectors together. The connector

will make a slight click when it is properly seated. At this point you are ready to begin operating your

engine.

Figure: Connecting Engine and Tender

To disconnect the engine and tender apply downward pressure near the tender until the connectors

separate.

The drawbar is able to withstand a 90 degree twist such as might be experienced in a derailment

where the engine or the tender would turn over and the other unit would remain upright.

If the drawbar is not properly connected your engine may exhibit erratic or no operation. If this

happens turn o the track power and make sure that the drawbar connectors are properly seated.

Then reapply power to the track and continue operation.

Figure: Engine and Tender

RAILKING

2-8-0 STEAM FREIGHT READY-TO-RUN

™

SET W/PROTO-SOUND

3.0 8

Your set comes with M.T.H.’s latest DCS component, the DCS Explorer. The Explorer communicates

with any Android or iOS smart phone or tablet running the free M.T.H. DCS App via a WiFi signal.

The app is available from the Apple App Store (for iOS devices) or Google Play (for Android devices).

It is possible to operate the train set with other controllers, including conventional transformers (like

the M.T.H. Z-1000), the DCS Remote Commander, the DCS Commander or the full DCS Digital

Command System. All of these devices are sold separately.

To install the DCS Explorer and power supply, please use the following instructions:

Black Harness Wire/Plug

Red Harness

Wire/Plug

DCS Explorer

DCS Power Supply Lighted

Lock-on

Red Harness

Wire/Plug

Black Harness Wire/Plug

Connecting the Transformer &

Installing DCS Explorer

RAILKING

2-8-0 STEAM FREIGHT READY-TO-RUN

™

SET W/PROTO-SOUND

3.0 9

Wi-Fi

Blue when

Wi-Fi available

POWER

Green when

plugged in

WPS

White when

WPS initiated

DCS Explorer Explained

WPS

“Wi-Fi Protected Set Up”

Press to connect to your

WPS capable router

TRACK OUT

Connect directly to

your track

HOME/MTH

Selects between

HOME and MTH

networks

PWR

Connect wall

adapter here

FUSE

Replaceable if

necessary

USB

Connect to Ethernet

(requires adapter)

Track

Purple when track

power and signals on

Red when track is

overloaded

O until a command

is sent from the app

Reset button

Press and release for Reboot

Press and hold 10 seconds for

factory reset

RAILKING

2-8-0 STEAM FREIGHT READY-TO-RUN

™

SET W/PROTO-SOUND

3.0 10

DOWNLOAD AND INSTALL DCS APP

for iOS and Android

iOS:

1. Tap the App Store icon on your Apple device

2. In the lower right of the screen, tap the magnifying

glass to search the app store

3. Tap the gray search bar at the top of the screen and

type “MTH DCS” without the quotation marks.

4. Tap the blue search button in the lower right corner

of the screen.

5. When the MTH Wi-Fi DCS app appears tap “GET”

in the upper right area of the screen.

6. Once the app downloads, the “GET” box will change

to “Install.”

7. Tap “Install” and the box will change to “Open.”

8. Tap Open to open the app.

9. There will now be an icon on your screen when you

want to open the app in the future.

Android:

1. Tap the Play Store icon on your Android device

2. Tap the white bar at the top of the page to bring up

the search function.

3. Type “MTH DCS” into the search bar without the

quotation marks.

4. Tap on the purple MTH logo for Wi-Fi DCS.

5. Tap on the Install button in the middle of the screen.

6. Once the app is installed, tap open to run your app.

7. There will now be an icon on your screen when you

want to open the app in the future.

RAILKING

2-8-0 STEAM FREIGHT READY-TO-RUN

™

SET W/PROTO-SOUND

3.0 11

Using the MTH Network

In MTH network mode, your DCS Explorer creates its own unique Wi-Fi network. In this mode, you

simply connect your smart device to the MTH network, open your app, and run your trains! Please

note, your smart device will not be connected to the internet while operating in MTH network mode.

1. Attach the antenna to the DCS Explorer.

2. Set the HOME/MTH selector switch to MTH.

3. Connect the DCS Explorer to the track using the red and black track connection

included in your set.

4. Connect the included power supply into the DCS Explorer.

5. Plug the DCS Explorer into an AC wall outlet.

6. Wait 1 minute for the WIU to initialize. When ready, the PWR and WI-FI LEDS will be

lit.

7. If you haven’t already, go to the iOS App Store or Google Play Store and install the

app on your smart device. Search for MTH DCS to quickly nd the app in either app

store.

8. In your smart device, navigate to Wi-Fi settings and connect to the MTH DCS

network. The network name (SSID) and network key are printed on the label axed to

the bottom of the DCS Explorer.

9. Open the app and select your DCS system type. The choices are DCS Explorer or

DCS WIU. You can change this later in app settings.

10. Tap RUN MY TRAINS.

11. Tap CHOOSE OR ADD AN ENGINE near the top of the screen and follow the

prompts.

12. After adding an engine(s), tap START UP and enjoy running your trains in

Wi-Fi DCS.

RAILKING

2-8-0 STEAM FREIGHT READY-TO-RUN

™

SET W/PROTO-SOUND

3.0 12

Using your home Wi-Fi Network

In HOME network mode, your DCS Explorer connects with your existing home Wi-Fi network. Just

make sure your smart device is connected as usual, open your app, and run your trains! In this mode,

you can choose the links within the app to check out our online catalogs, newsletters, or search for

products.

For Routers with WPS (Wi-Fi Protected Setup)

1. Attach the antenna to the DCS Explorer.

2. Set the HOME/MTH selector switch to HOME.

3. Connect the DCS Explorer to the track using the red and black track connection

included in your set.

4. Connect the included power supply into the DCS Explorer.

5. Plug the DCS Explorer into an AC wall outlet.

6. Wait 1 minute for the DCS Explorer to initialize. When ready, the PWR and WI-FI

LEDS will be lit.

7. Press the WPS BUTTON on your home Wi-Fi router and then press and release the

WPS BUTTON on your DCS Explorer. Note, some routers may require you to press

and hold the WPS BUTTON for several seconds. Check the manual for your specic

router.

8. Wait until the white WPS LED on the DCS Explorer is on steadily. It will go o after a

few minutes.

9. If you haven’t already, go to the iOS App Store or Google Play Store and install the

app on your smart device. Search for MTH DCS to quickly nd the app in either app

store.

10. Make sure your smart device has Wi-Fi turned on and is connected to the Wi-Fi

network of the router.

11. Open the app and select your DCS system type. The choices are DCS Explorer or

DCS WIU. You can change this later in app settings.

12. Tap RUN MY TRAINS.

13. Tap CHOOSE OR ADD AN ENGINE the tap ADD MTH ENGINE and follow the

prompts.

14. Tap START UP and enjoy running your trains in Wi-Fi DCS!

For Routers that Require Manual Setup (no WPS feature)

1. Attach the antenna to the WIU.

2. Set the

HOME/MTH selector switch to MTH.

3. Plug the DCS Explorer into an AC wall outlet.

4. Wait 1 minute for the DCS Explorer to initialize. When ready, the

PWR and WI-FI LEDS will be

lit.

5. Using A PC with Wi-Fi, navigate to see the available wireless networks and connect to the

MTH_DCS-XXXX. The network name is printed on the bottom of your module.

RAILKING

2-8-0 STEAM FREIGHT READY-TO-RUN

™

SET W/PROTO-SOUND

3.0 13

6. When prompted, enter the network key mthdcswi all lower case. The network key is also

printed on the bottom of your module.

7. Open your web browser and enter the IP address 192.168.143.1 in the url address line. This is

usually the top text box in your browser. This will open LuCI, the MTH DCS web interface.

8. Enter the password

MTHDCS and hit enter. Do not change the username from ROOT.

9. Select the STATION MODE tab along the top of the screen. Then, select

WIRELESS from within that tab. Wireless is the only option under Station Mode.

10. In the ESSID

eld, enter the network name (SSID) you want to connect the module to. This is

probably the same network you connect your phone or other devices to.

11. If your network is secured (requires a password) then select the encryption type from the drop

down menu. If you don’t know your encryption type, try the last choice which is mixed mode. If

that doesn’t work, you will need to obtain your specic encryption type from your router.

12. Enter your home network password in the KEY eld. This is also known as your

NETWORK KEY.

13. Click the SAVE AND APPLY button in the lower right part of the screen.

14. Remove power from the DCS Explorer and close your browser.

15. Set the HOME/MTH selector switch to HOME.

16. Follow the instructions for connection to your home network using WPS in the previous section,

however, ignore steps 7 and 8. The WIU will now automatically connect to your home network

each time it is powered up.

RAILKING

2-8-0 STEAM FREIGHT READY-TO-RUN

™

SET W/PROTO-SOUND

3.0 14

Using a wired Ethernet Network

If you prefer, the DCS Explorer can be hard wired to your network router using standard Ethernet

cables and a USB to Ethernet apdapter. In this conguration, a network router is required. The smart

device typically connects to the router via Wi-Fi, so there is limited benet to using this conguration.

It may improve overall performance in an environment with unreliable Wi-Fi network signaling.

1. Attach the antenna to the DCS Explorer (It isn’t necessary of course but, it’s a great

place to store it!).

2. Set the HOME/MTH selector switch to MTH (I know, it seems odd but, trust us).

3. Connect the DCS Explorer to the track using the red and black track connection

included in your set.

4. Connect the DCS Explorer to your network router using a standard Ethernet cable

and USB to Ethernet adapter.

5. Plug the DCS Explorer into an AC wall outlet.

6. Wait 1 minute for the DCS Explorer to initialize. When ready, the PWR and WI-FI

LEDS will be lit.

7. If you haven’t already, go to the iOS App Store or Google Play Store and install the

app on your smart device. Search for MTH DCS to quickly nd the app in either

app store.

8. Make sure your smart device has Wi-Fi turned on and is connected to the Wi-Fi

Network of the router.

9. Open the app and tap RUN MY TRAINS.

10. Tap CHOOSE OR ADD AN ENGINE then tap ADD MTH ENGINE and follow the

prompts.

11. Tap START UP and enjoy running your trains in Wi-Fi DCS!

RAILKING

2-8-0 STEAM FREIGHT READY-TO-RUN

™

SET W/PROTO-SOUND

3.0 15

Luci

LuCI is a web interface for your DCS Explorer. Think of is as custom web page used exclusively for

accessing advanced set up and features in your DCS Explorer unit. To operate Wi-Fi DCS, most

people will not need to access LuCI. However, if MTH releases an update to your DCS Explorer

rmware, you will want to meet her.

Accessing LuCI

1. Disconnect all cables from your WIU DCS Explorer.

2. Set the

HOME/MTH selector switch to MTH.

3. Plug the DCS Explorer into an AC wall outlet.

4. Using a smart device or Wi-Fi capable laptop/PC, navigate to see the available wireless net-

works and connect to the

MTH_DCS-XXXX. The network name is printed on the bottom of

your module.

5. When prompted, enter the network key mthdcswi all lower case. The network key is also

printed on the bottom of your module.

6. Open your web browser and enter the IP address 192.168.143.1 in the url address line. This is

usually the top text box in your browser. This will open LuCI, the MTH DCS web interface.

7. Enter the password MTHDCS and hit enter. Do not change the username from ROOT.

RAILKING

2-8-0 STEAM FREIGHT READY-TO-RUN

™

SET W/PROTO-SOUND

3.0 16

8. The home page of LuCI will be displayed.

Updating DCS Explorer Firmware

1. Access LuCI (see instructions above in this section).

2. Select the SYSTEM tab near the top of the page.

RAILKING

2-8-0 STEAM FREIGHT READY-TO-RUN

™

SET W/PROTO-SOUND

3.0 17

3. Select BACK-UP/FLASH FIRMWARE from the drop down list.

4. Scroll down the page until you see FLASH NEW FIRMWARE IMAGE near the bottom

of the page.

5. Leave the KEEP SETTINGS box checked. This saves your network settings.

6. Select CHOOSE FILE and navigate to the new rmware lename, select the le,

and click OPEN.

RAILKING

2-8-0 STEAM FREIGHT READY-TO-RUN

™

SET W/PROTO-SOUND

3.0 18

7. Wait until the le window closes (up to 15 seconds). Verify the lename selected is

displayed next to the CHOOSE FILE button.

8. Select FLASH IMAGE...

9. When the FLASH FIRMWARE - VERIFY page is displayed, select the blue

PROCEED button.

10. You should now see the SYSTEM FLASHING SCREEN.

Note: While the rmware image is being ashed, DO NOT TOUCH THE DEVICE

(tablet, phone, PC, laptop) OR THE DCS EXPLORER! WAIT A FULL 3 MINUTES.

IF YOU DO NOT, THE DCS EXPLORER COULD BE DAMAGED AND REQUIRE SERVICE!

RAILKING

2-8-0 STEAM FREIGHT READY-TO-RUN

™

SET W/PROTO-SOUND

3.0 19

11. After waiting a full 3 minutes, it is now safe to remove power from the DCS Explorer

and reconnect it to your layout.

Note: LuCI will never tell you that the step is complete. It will remain on the

system ashing screen indenitely. This is why you must wait 3 minutes.

Changing the SSID and Network Key for MTH Wi-Fi Network Mode

For security purposes, like operating in a public setting, you may want to change the SSID and

Network Key. These are also known as the Network Name and Password for those of us who are less

technical. Either way, it’s easy.

1. Access LuCI (see instructions above in this section).

2. Select the AP MODE tab at the top of the page.

3. Select WIRELESS from the drop down menu.

4. Scroll to the top of the page.

5. In the ESSID box, delete the contents and enter the new SSID or network name.

Page is loading ...

RailKing 30-4244-1 User manual

Brand: RailKing

Model: 30-4244-1

Type: User manual

This manual is also suitable for

30-4245-1

Download PDF

report

RailKing 30-4244-1 User manual

This manual is also suitable for

RailKing 30-4244-1 User manual

Related papers

Other documents