2. Hoshizaki
  3. HS-5234

Hoshizaki HS-5234 User manual

  • Hello! I am an AI chatbot trained to assist you with the Hoshizaki HS-5234 User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
1
2A8351-010
Hoshizaki Optional Heated Overow Drain Pan Kit
HS-5234
For Use with Commercial "S" Series Upright Models
Installation Instructions
Check to ensure that all parts are included:
Index
No. Description
Part
Number Qty
1 Heated Overow Drain Pan
(includes 8 ft. (2.4 m) Power Cord)
3A9247-01 1
2 Heated Overow Drain Pan Bracket 3A9248-01 1
3 Rubber Gasket 413854-03 1
4 Drain Fitting 4A2792-01 1
5 Silicone Hose (3/8×1/2 in.; L = 2 m) 7730I3812 1
6 Wire Harness (6 in.) 4A6030-01 1
7 Self-Drilling Hex Screw 7B03I1210 8
8 Nylon Tie Mount 437618-01 1
9 Nylon Tie 8911-0200 4
10 Wire Clamp 4A0809-03 4
11 Wiring Label 3A9294-01 1
WARNING
• The appliance should be serviced only by qualied service personnel to reduce the risk of death, electric
shock, serious injury, or re.
• No installation or service should be undertaken until the technician has thoroughly read these instructions.
Failure to follow these instructions will adversely affect safety, performance, component life and warranty
coverage, and may result in costly water damage.
• To reduce the risk of electric shock, do not touch the plug with damp hands. Move the power switch to the
"OFF" position, then unplug the appliance from the electrical outlet before servicing.
Installation Instructions
1) Move the power switch to the "OFF" position, then unplug the appliance from the electrical outlet.
2) Move the appliance out to access the rear of the appliance.
3) Remove the channel cover and condensate pan from the rear of the appliance. See Fig. 1.
4) Pour the condensate water out, then clean and dry the condensate pan.
Fig. 1
Model Shown: CF1S-FS
Condensate Pan
Channel CoverDrain Boot
Drain Boot
2
2A8351-010
6) Once tight, replace the condensate pan and channel cover in their correct positions. Connect the silicone hose provided in this kit
onto the end of the drain tting. See Fig. 3. NOTICE! Be sure the drain boot is correctly positioned back into the condensate
pan.
7) Place the heated overow drain pan into the heated overow drain pan bracket. See Fig. 4.
Fig. 3
Drain Fitting
Condensate Pan
Drain Fitting
Silicone Hose
Drain Boot
Channel Cover
Fig. 4
Heated Overow
Drain Pan Assembly
Heated Overow Drain
Pan Bracket
Drain Fitting Nut
Drain Fitting
Fig. 2
Condensate Pan
Rubber Gasket
Condensate Pan
Drain Fitting
Overow Hole
5) Remove the drain tting nut from the drain tting provided in this kit, then apply thread sealant tape or thread sealant to the drain
tting. Place the drain tting into the overow hole from the outside. Next, place the rubber gasket and drain tting nut onto the drain
tting and tighten. See Fig. 2. Be sure the drain tting is facing down.
Rear
Front
Thread Sealant Tape
or Thread Sealant
Heated Overow
Drain Pan
Front
Rear
Model Shown: CF1S-FS
3
2A8351-010
9) Measure 13-3/4 in. (349 mm) from the right side of the appliance. Next, measure up 12 in. (305 mm) from the top of the heated
overow drain pan mounting bracket and place a mark. Next, drill a 1/4 in. (6mm) hole at the mark.
See Fig. 6. NOTICE! Do not drill deeper than 1 in. (25 mm). Drilling deeper could penetrate the interior cabinet wall.
Fig. 7
Fig. 6
Nylon Tie Mount
1/4 in. (6 mm)
Nylon Tie Mount Hole
NOTICE!
Do not drill
deeper than
1 in. (25 mm)
12 in. (305 mm)
10) Place a nylon tie through the nylon tie mount and close (do not tighten). Route the silicone hose through the nylon tie then down into
the large center hole at the top of the heated overow drain pan mounting bracket. See Fig. 7. Do not cut the silicone hose at this
time.
13-3/4 in.
(349 mm)
Silicone Hose
Heated Overow Drain
Pan Assembly
Larger Center
Hole
Center
Nylon Tie
Nylon Tie Mount
8) Place the heated overow drain pan assembly at the rear of the appliance as shown in Fig. 5. Measure from the right side of the
appliance as shown for proper location. Lift it ush against the rear panel of the appliance and secure using 4 of the self-drilling hex
screws provided in this kit. See Fig. 5. The heated overow drain pan power cord connector should be facing the right side from rear
view.
Fig. 5
Self-Drilling
Screws
Heated Overow Drain Pan
Power Cord Connector
Heated Overow Drain Pan Assembly
Model Shown: CF1S-FS
Model Shown: CF1S-FS
Model Shown: CF1S-FS
Center of Appliance (1 section)
(Right Side on 2 Section Appliance)
4
2A8351-010
11) Plug the 8 ft. (2.4 m) heated overow drain pan power cord into the heated overow drain pan connector then place the 8 ft. (2.4 m)
heated overow drain pan power cord in the 4 wire clamps supplied with this kit. Using the self-drilling hex screws provided, measure
and secure the 4 wire clamps at the locations shown below. See Fig. 8.
Fig. 8
5 ft.
(1.5 m)
6 in. (152 mm)
4 in. (102 mm)
1 in. (25 mm)
A
B
C
D
42 in.
(609 mm)
3.5 ft.
(1066 mm)
1 in. (25 mm)
1 in. (25 mm)
A
B
C
D
Wire Clamp
Wire Clamp
Wire Clamp
Wire Clamp
Heated Overow Drain
Pan Power Cord
Self-Drilling
Screw
Self-Drilling
Screw
Self-Drilling
Screw
Self-Drilling
Screw
Heated Overow Drain Pan
Power Cord Connector
Heated Overow Drain
Pan Power Cord
Model Shown: CR1S-FS
Model Shown: CF1S-FS
5
2A8351-010
12) Use nylon ties to secure the silicone hose to the heated overow drain pan power cord above wire clamps B and C. See Fig. 9.
Be sure not to over tighten or pinch the silicone hose.
13) Remove the silicone hose from the heated overow drain pan. Conrm there are no kinks in the hose, then tighten the center nylon
tie. Be sure not to over tighten or pinch the silicone hose.
14) Measure the silicone hose so that the silicone hose extends a minimum of 1 in. (25 mm) into the heated overow drain pan but not
deep enough to touch the bottom of the heated overow drain pan. Once the correct amount of hose length is determined, mark the
distance needed and cut the silicone hose to that length.
B
C
Nylon Tie
Nylon Tie
Center
Nylon Tie
Heated Overow Drain
Pan Power Cord
Silicone Hose
Silicone Hose
Heated Overow
Drain Pan
Nylon Tie
Nylon Tie
Center
Nylon Tie
Silicone Hose
Heated Overow
Drain Pan
Heated Overow Drain
Pan Power Cord
Fig. 9
Model Shown: CF1S-FS
6
2A8351-010
Wiring Instructions
If wire harness is already factory installed skip to step 19. Otherwise, continue to step 15.
15) Remove the control box cover. Next, route the wire harness into the control box through the hole with the appliance power cord.
See Fig. 10.
16) Connect the wire harness black (BK) ribbed wire to the terminal block line black (BK) bar.
17) Connect the wire harness black (BK) smooth wire to the terminal block neutral white (W) bar.
18) Attach the wire harness ground (BK) ring terminal to the unit ground screw. WARNING! Make sure grounding wires are attached
and secure.
Wire Harness
Terminal Block
Wire Harness
Black (BK)
Ribbed Wire
Terminal Block
Neutral White (W) Bar
Unit Ground Screw
Terminal Block Line
Black (BK) Bar
Wire Harness
Black (BK)
Smooth Wire
Wire Harness
Ground (BK) Wire
Wire Harness
Heated Overow Drain
Pan Power Cord
Control Box
Control Box
19) Plug the heated overow drain pan power cord into the wire harness connector. Secure the heated overow drain pan power cord to
the appliance main power cord with a nylon tie. See Fig. 11.
20) Place the wiring label supplied with this kit near the wiring label on the appliance.
21) Replace the control box cover in its original position.
Fig. 10
Fig. 11
Nylon Tie
Fig. 12
22) Move the appliance back to its original position. Ensure that the heated overow drain pan assembly does not make contact with the
back wall or another surface. Plug the appliance into the electrical outlet, then move the power switch to the "ON" position.
Appliance Power Cord
Appliance Power Cord
/