Silvercrest SFK 16 A1 User Manual And Service Information

Category
Door intercom systems
Type
User Manual And Service Information
Wireless Doorbell
Draadloze deurbel
Brugervejledning og
serviceinformation
DK
Wireless Doorbell
User manual and
service information
GB
IE
Radio-ohjattu ovikello
Käyttöopas ja huolto-ohjeet
FI
Radiostyrd dörrklocka
Istruzioni per l’uso e
informationi di servizio
SE
SFK 16 A1
3
TARGA GmbH
Lange Wende 41
D-59494 Soest
www.silvercrest.cc
Mod.-Nr. SFK 16 A1
Mat-No: 1618147
HOME TECH
Wireless Doorbell SFK 16 A1
English - 1
Table of Contents
Package Contents 3
Important Safety Instructions 5
Intended use 6
Children and Persons with Disabilities 7
Batteries 8
RF Interface 9
Operating Environment 10
Repair and Maintenance 12
Copyright 13
Conformity Notice 14
Introduction 15
Inserting the Batteries 15
Batteries for the Receiver 15
Replacing the transmitter battery 16
Mounting the Devices 17
Mounting the Transmitter 18
Mounting the Receiver 19
Filling out the Name Label 19
Operation 20
Wireless Doorbell SFK 16 A1
2 - English
Selecting the Signalisation 20
Selecting the Bell Melody 21
Adjusting the Volume 21
Appendix 22
Disposal of Old Devices 22
Technical Specifications 24
Warranty Information 25
Version 1.22
Wireless Doorbell SFK 16 A1
English - 3
Package Contents
- Receiver
- Transmitter
Wireless Doorbell SFK 16 A1
4 - English
Not illustrated:
- 3 AA-sized batteries, 1,5V
- 1 A23-sized battery
(already fitted in transmitter)
- 3 rawlplugs, 5mm
- 3 fixation screws
- 2 rubber rings
- 5 name labels
Description of figures:
1 Speaker
2 Melody selection button
3 Optical display
4 Mode selection switch
5 Volume selection switch
6 Bell button
7 Name label
8 Nose latch for upper housing piece
Wireless Doorbell SFK 16 A1
English - 5
Important Safety Instructions
Before you use this device for the first time,
please read the following notes in this manual
and heed all warnings, even if you are familiar
with handling electronic devices. Keep this
manual safe for future reference. If you sell the
device or pass it on, it is essential you hand
over this manual also.
This icon denotes important
information for the safe operation of
the product and for the user’s safety.
This symbol denotes further
information on the topic.
Wireless Doorbell SFK 16 A1
6 - English
Intended use
This wireless door bell comprising a transmitter
and a receiver is designed to initiate an acoustic
and/or visual signal on the receiver when the
transmitter is actuated. This device is not
designed for commercial use or installation and
operation in a company. This device is sold for
private use only. This device meets the
requirements of all relevant norms and
standards in conjunction with conformity.
Compliance with these standards is no longer
guaranteed in the event of unauthorised
modifications to the device. The manufacturer
does not accept any liability for any resulting
damage or faults in such cases. Only use
accessories specified by the manufacturer. Any
other use is not as intended.
Wireless Doorbell SFK 16 A1
English - 7
Children and Persons with
Disabilities
Electrical appliances do not belong in the hands
of children. People with disabilities should only
use electrical devices in appropriate
circumstances. Do not allow children or persons
with disabilities to use electrical devices when
not under supervision. These may not
comprehend the presence of potential risks.
Batteries and small parts represent potential
choking hazards. Keep the batteries in a safe
place. If a battery is swallowed, seek medical
help immediately. Keep the packaging away
from children and persons with disabilities too.
as there is danger of suffocation.
Wireless Doorbell SFK 16 A1
8 - English
Batteries
Insert the batteries with the correct polarity.
Never try to recharge the batteries and under no
circumstances throw them into fire. Do not
short-circuit any batteries. Remove batteries
when the device is not to be used for a long
time. Non-intended use may cause explosion
and danger to life. Leaked batteries must be
handed in to a collection point for old batteries.
Make sure you wear protective clothing (such as
gloves) when manipulating leaked batteries.
Wireless Doorbell SFK 16 A1
English - 9
RF Interface
Place the device at least 20cm (8 inches) away
from pacemakers, as the RF signals may
interfere with the functionality of the pacemaker.
The transmitted RF signals can cause
interference with hearing aids. Do not place the
device with the wireless adapter turned on near
flammable gases or in an explosion-sensitive
area (e.g. a paint shop), as the transmitted RF
signals may cause explosions or fire. The range
of the radio wave signals depends on
environmental conditions.
Wireless Doorbell SFK 16 A1
10 - English
Operating Environment
Receiver
The receiver is not designed for use in
environments with a high temperature or
humidity (e.g. bathrooms), and must be kept
free from dust. Operating temperature and
operating humidity: 5°C to 40°C, max. 90% RH.
Transmitter
The transmitter is designed for use in
environments with a high humidity (e.g.
bathroom) and is protected against water
splashes. Operating temperatures and
operating air humidity: -10°C to +40°C, higher
than 90% rel. air humidity.
Wireless Doorbell SFK 16 A1
English - 11
Always make sure that:
- no direct heat sources (e.g. heating) can
affect the devices;
- the receiver is not exposed to direct
sunlight or artificial light;
- the devices are never placed in the
immediate vicinity of magnetic fields (e.g.
loudspeakers);
- no fire sources (e.g. burning candles) are
placed on or near the devices;
- no foreign bodies are introduced into the
device;
- the receiver is not exposed to extreme
temperature fluctuations;
- the devices are not subject to excessive
shocks and vibrations;
Wireless Doorbell SFK 16 A1
12 - English
Repair and Maintenance
Repair work is necessary if the device has been
damaged or if water or objects have penetrated
inside the housing, the receiver is exposed to
rain or if it does not work correctly or has been
dropped. If smoke, unusual noises or smells are
noticed, power off the device immediately. In
these cases the device should not be used
further and should be inspected by authorized
service personnel. Please contact qualified
personnel when repair is needed. Only use a
clean, dry cloth for cleaning. Never use any
corrosive liquids.
Wireless Doorbell SFK 16 A1
English - 13
Copyright
The entire content of this User’s Manual is
copyrighted and is provided to the reader for
information purposes only. Copying data and
information without the prior written and explicit
authorization from the author is strictly
forbidden. This also applies to any commercial
use of the contents and information. All texts
and figures are up-to-date as per the date of
print release. We assume no liability for any
changes.
Wireless Doorbell SFK 16 A1
14 - English
Conformity Notice
This product has been tested and
approved for compliance with the basic
and other relevant requirements of the
R&TTE Directive 1999/5/EC.
The corresponding Declaration of Conformity
can be found at the end of this User's Manual.
Wireless Doorbell SFK 16 A1
English - 15
Introduction
Thank you for buying this wireless door bell.
This device enables the installation of a wireless
door bell system. You can install this wireless
bell on an entrance door, for example. There is
no need for a manual RF synchronisation
between the transmitter and the receiver.
Inserting the Batteries
Both devices are battery-powered. Insert the
supplied batteries into the receiver. The battery
of the transmitter is already fitted.
Batteries for the Receiver
- Open the receiver’s battery compartment
by pushing the back panel cover in the
direction of the arrow mark.
- Insert the supplied batteries (size AA) into
the receiver. Make sure that the batteries
are properly aligned according to the
polarity (+ and -). The correct polarity is
Wireless Doorbell SFK 16 A1
16 - English
labelled on the batteries and inside the
battery compartment.
- Slide the battery compartment cover onto
the receiver housing.
Replacing the transmitter battery
- The transmitter battery is already fitted and
only requires replacement when it is empty.
-
To open the transmitter housing, use a flat
screwdriver. Insert the screwdriver carefully
into the transmitter housing side and press
it slightly inwards to release the nose latch
(8). Then pull the upper housing piece
upwards.
- Remove the type A23 12 V battery from the
top section of the transmitter and replace
the empty battery with a new battery of the
same type. Always ensure correct polarity
of the battery (pay attention to the + and –
marks). The correct polarity is labelled on
the battery and inside the transmitter
housing.
Wireless Doorbell SFK 16 A1
English - 17
- Replace the upper housing piece onto the
transmitter base unit.
You may also leave the base unit
piece separated if you want to mount
the transmitter on the wall.
Mounting the Devices
The package includes all necessary material for
mounting both devices. Alternatively you may
simply leave the receiver for stand-up
installation.
Make sure that the distance between
transmitter and receive does not
exceed the maximum range. If
necessary, test their proper
functionality prior to mounting the
devices in their position.
Wireless Doorbell SFK 16 A1
18 - English
Mounting the Transmitter
Look for a suitable place where you want to
mount the transmitter.
- Open the transmitter housing by inserting a
flat screwdriver into the notch on the
housing side. Carefully push the nose latch
(8) inwards. You can then remove the
upper housing piece.
- Drill two 5mm holes at a distance of 50mm
in the wall.
- Insert two of the supplied rawlplugs into
these holes.
- Place the two rubber rings into the recess
of the base plate.
- Insert two of the supplied screws through
the holes located in the bottom piece of the
transmitter housing and then screw them
onto the rawlplugs.
- Replace the upper housing piece by
pushing it onto the base unit piece.
Wireless Doorbell SFK 16 A1
English - 19
Mounting the Receiver
- Drill one 5mm hole at the desired position
on the wall.
- Insert one of the supplied rawlplugs into
this hole.
- Screw one of the supplied screws into the
rawlplug until its head is approx. 2mm away
from the wall.
- Place the receiver onto the screw head.
The wall-mounting hole located at the back
of the housing must completely fit over the
screw head. By pulling it down carefully the
receiver clicks into place on the screw
head.
Filling out the Name Label
Remove the transparent plastic cover from the
receiver. Underneath you can write on the name
label (7). The package contains 5 labels for
future replacement. Replace the plastic cover by
pushing it onto the transmitter housing.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105

Silvercrest SFK 16 A1 User Manual And Service Information

Category
Door intercom systems
Type
User Manual And Service Information

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI