Scotsman CME1686RLS User manual

Brand: Scotsman

Model: CME1686RLS

Category: Ice cube makers

Type: User manual

This manual is also suitable for

CME1386RLS

Introduction:

This manual covers the assembly, installation, start

up, operation and maintenance of the 1300 and

1600 remote low side cuber systems.

An illustrated parts list and wiring diagram is in the

center of this manual.

Keep this manual for future reference.

Eclipseä 1300,1600

September 2003

Page 1

Table of Contents

Introduction: ·················· Page 1

Configuration: ················· Page 2

Technical Specifications ············ Page 3

Model Number Locations ··········· Page 4

Cabinet Drawings, Ice Making System ···· Page 5

Cabinet Drawings, Compressor Package and

Condensers ·················· Page 6

Proper Combinations: ············· Page 7

Create the System··············· Page 8

System Examples ··············· Page 9

System Examples ··············· Page 10

Place Remote System ············· Page 11

System Location ················ Page 12

Route Tubing ················· Page 13

Ice Making Section ·············· Page 14

Compressor Package ············· Page 15

Condensing Section Assembly ········ Page 16

Condensing Section Assembly ········ Page 17

Ice making section: ·············· Page 18

Bin Thermostat - Routing ··········· Page 19

Bin Thermostat - Bracket & Bulb ······· Page 20

Water and Drain ················ Page 21

Water and Drain ················ Page 22

Ice Making Section Set Up ·········· Page 23

Coupling Connections: ············ Page 24

Condensing Unit Connections ········· Page 25

Final Placement ················ Page 26

Controller Operation ·············· Page 27

Initial Start Up - 1300 and 1600 ········ Page 28

Purge Adjustment ··············· Page 29

System Operation:··············· Page 30

Refrigeration Details: ············· Page 31

Technicians Only: Freeze Cycle Sequence of Operation

·························Page 32

Technicians Only: Harvest Cycle Sequence of

Operation ··················· Page 33

Power and Water Interruptions ········ Page 34

Sanitation and Cleaning ············ Page 35

Other Maintenance ·············· Page 36

Water Distributors ··············· Page 37

Ice Sensors ·················· Page 38

Water Level Sensor Maintenance ······· Page 39

Service Diagnosis ··············· Page 40

Service Diagnosis ··············· Page 41

Service Diagnosis ··············· Page 42

Controller Features & Last Error Recall ···· Page 43

Operational Characteristics 1300 lb system · · Page 44

Operational Characteristics 1600 lb system · · Page 45

Refrigeration System Service ········· Page 46

Note this symbol when it appears. It

indicates a potential hazard.

Configuration:

A remote low side cuber system includes several

sub systems: an ice making section, a remote

compressor package, and a remote air cooled

condenser. Additionally, there are two models of

each sub-system and this manual covers all of

them.

The ice making sections are designed for use

indoors in a controlled environment. The remote

compressor packages and condensers are

designed to operate outdoors. Each sub-system

has limits for power, water and temperature.

Operational Limitations:

Minimum Maximum

Air Temp (IMS) 50

F 100

Air Temp (CU) -20

F. 120

Water Temp 40

F. 100

Water Pressure 20 psi 80 psi

Voltage (IMS) 104 126

Voltage (CU) 198 253

IMS = Ice Making Section, CU= Condensing Unit

Do Not operate the machine in conditions beyond

these limitations. Doing so will void the warranty.

Scotsman ice systems are designed and

manufactured with the highest regard for safety

and performance. They meet or exceed the

standards of UL and NSF.

Scotsman assumes no liability of responsibility of

any kind for products manufactured by Scotsman

that have been altered in any way, including the

use of any part and/or other components not

specifically approved by Scotsman.

Scotsman reserves the right to make design

changes and/or improvements at any time.

Specifications and design are subject to change

without notice.

Warranty

Refer to the warranty coverage in effect when the

equipment was sold. Warranty statements are

included with each product.

Systems:

Each sub-system is a separate entity that carries

its own model and serial number. They must be

combined to create a remote cuber low side

system.

Eclipseä 1300, 1600

September 2003

Page 2

System Model

Number

Condensing Unit (CU) Ice Making Section (IMS)

Compressor Package Condenser

Model Electrical Model Electrical Model Electrical

Eclipse 1300-42 CP1316-32A 208-230/60/1

ERC1086 -32A 208-230/60/1 CME1386RLS-1A 115/60/1

Eclipse 1300-43 CP1316-3A 208-230/60/3

Eclipse 1600-42 CP1316-32A 208-230/60/1

ERC1086-32A 208-230/60/1 CME1686RLS-1A 115/60/1

Eclipse 1600-43 CP1316-3A 208-230/60/3

Notes: Voltage Codes are at the end of the model number. Codes read Voltage/Hertz/Phase. Those related

to these products include:

-1 = 115/60/1

-3 = 208-230/60/3

-32 = 208-230/60/1

-42 = 115/60/1 and 208-230/60/1 (separate units)

-43 = 115/60/1 and 208-230/60/3 (separate units)

System Information

Pre-charged tubing kits are required to

interconnect the IMS to the CP.

Interconnecting 24 volt control wire ships with the

CP unit.

Technical Specifications

Ice Making Section (IMS)

Compressor Package (CP)

Condenser

* * ERC condenser fan motor is powered from CP

unit and the ERC’s ampacity is included in CP unit

numbers.

Note: The ERC1086 does NOT contain a

headmaster. The headmaster is in the CP units.

Note: 75 feet of interconnecting control wire (24

volt) is included with the CP units.

Eclipseä 1300,1600

September 2003

Page 3

Model Voltage Minimum Circuit

Ampacity

Max Fuse Size Cabinet Size Weight (lb)

CME1386RLS-1A 115/60/1 3 15 30”w x 24”d x 28”h 144

CME1686RLS-1A 115/60/1 3 15 same 154

Model Voltage Contains

Headmaster?

Minimum

Circuit

Ampacity

Max

Fuse

Size

Refrigerant

Charge (R-404A)*

Cabinet Size Weight

(lb)

CP1316-32A 208-230/60/1 Yes 24.3 30 18 lb 29 ¾”wx18”dx34½”h 180

CP1316-3A 208-230/60/3 Yes 15.3 20 18 lb same 180

* Includes entire system charge.

Model Voltage Contains

Headmaster?

Number

Circuits

Minimum

Circuit

Ampacity**

Max

Fuse

Size**

Cabinet Size, with legs Weight

(lb)

ERC1086-32A 208-230/60/1 No 1 1.25 15 29 ¾”w x 28 5/8”d x 38 ½”h 95

Model Number Locations

Ice Making Section

The dataplate on the back of the ice machine

contains the model number, serial number and

electrical data.

A second plate, located behind the front panel at

the lower left front, also lists the model and serial

numbers.

Compressor Package

The dataplate on the right side of the

compressor package contains the model

number, serial number, electrical data and

system refrigerant charge.

A second plate, located behind the front

panel in front of the compressor, also lists

the model number, serial number and

refrigerant charge.

Condenser

The dataplate lists the condenser’s

electrical information plus the model

and serial numbers.

On the ERC1086 it is located on the side

opposite the refrigeration connections.

Eclipseä 1300, 1600

September 2003

Page 4

Dataplate

location for

CP Unit

Dataplate

location for

ERC1086

Dataplate

location for

Ice Making

Section

Cabinet Drawings, Ice Making System

Eclipseä 1300,1600

September 2003

Page 5

17.08

2.53

4.85

17.31

TOP VEIW

ICEDROPAREA

TOP ACCESS

REFRIGERANT

LINE SETS

UTILITY CHASE

30.00

3.02

1.90

15.76

5.19

REAR VEIW

WATER INLET

3/8" FLARE

DRAIN

3/4" PVC

FEMALE

REFRIGERANT

LINE SETS

CONNECTIONS

24.00

3.18

Thermostat

Routing Hole,

13” from front,

4.63” from side

Cabinet Drawings, Compressor Package and Condensers

Eclipseä 1300, 1600

September 2003

Page 6

BACK VIEW

FRONT VIEW

RIGHT SIDE VIEW

1/2" COOL VAPOR LINE

0.88 ELECTRICAL INLET

3/4" SUCTION LINE

INTERFACE HARNESS

ACCESS HOLE

3/8" CONDENSER LIQUID LINE (OUT)

1/2" C

NDENSER DISCHARGE LINE (IN)

CONDENSER FAN WIRE ROUTING

ERC680 or ERC1086:

This Side Attaches to

CP1316

27.90

28.53

35.72

2.75

Liquid Line

Discharge

Line

29.50

38.47

33.19

6.68

22.51

29.19

9/16” Mounting Hole

23.5”

1.5”

3/8" LIQUID LINE

15”

1.5”

Proper Combinations:

The three sub systems are designed to be

connected together in certain combinations to meet

the user’s needs:

Eclipse 1300 System:

CME1386, CP1316, ERC1086

Eclipse 1600 System:

CME1686, CP1316, ERC1086

ERC1086 may be substituted for by an approved

central condenser coil & fan (coil must be without

headmaster - headmaster is part of CP1316).

Condenser coil internal volume target is 165 cubic

inches, BHTU target is 42,000 BTUH.

Note: The ice making section cannot be stacked

vertically.

Accessories such as bin adapters and tubing kits

are required to complete the installation.

Dispenser Adapter Kits:

Scotsman ID200 or ID250: KBT44

Note: Dispensers with two rotors. If possible, the

ice making head should NOT be centered left to

right between the two rotors. It should be shifted

slightly to one side, and the agitation should be

minimized.

Bin Adapter Kits:

BH800: KBT23

BH801: KBT29

BH900: KBT22

Tubing Kits:

20 foot: 3RTE20

35 foot: 3RTE35

50 foot: 3RTE50

75 foot: 3RTE75

Suction Line Trap: KSLT075

Interconnecting Tubing to Approved Rack

Condenser Coil: RTE10

Line end kit: KTE6

Items required for installation:

Ice making section

Compressor Package (includes interconnecting

control system wire)

Remote condenser or approved rack coil

w/tubing kit

20’, 35’, 50’ or 75’ triple line set (liquid, vapor

and suction)

Bin or dispenser adapter

Special Considerations

The ice making section’s footprint is 30” wide by

24” deep. The refrigeration connections can be

made out the top panel or out the back. The

electrical power cord and the water inlet line can

also be routed through either of those areas. The

drain may be routed out the back or to the left side.

The bin thermostat, when deployed, will be about

5” below the bottom of the cabinet, and that is

where the ice will fill to. This ice level maximizes

ice storage without overfilling the bin or dispenser.

Water

Pure water does not exist. All water supplies

contain some amounts of impurities, although

potable water is, by definition, fit for human

consumption. Because the contents of the water to

an ice machine directly impact its performance,

consideration should be given to improving the

water’s quality.

There are two ways water can contain impurities:

in suspension or in solution. Suspended solids can

be filtered out of the water. In solution or dissolved

solids must be diluted or treated. Water filters are

recommended to remove the suspended solids.

Some filters or filter systems have treatment

chemicals in them for treating the suspended

solids.

This ice machine has an adjustment for the amount

of water rinsed or purged. Water use adjustments

are customer convenience adjustments; they are

not factory defects and are not covered by

warranty.

Eclipseä 1300,1600

September 2003

Page 7

Create the System

Plan the installation. The system consists of four

parts: the ice making section, the compressor

package, the interconnecting tubing and the

remote condenser. Of these, the biggest variable is

the interconnecting tubing.

Tubing: The tubing consists of three pre-charged,

insulated and sealed soft copper tubes. They each

contain a small holding charge of R-404A. One

tube, the liquid line, is 3/8” OD. The vapor tube is

½” OD and the suction tube is ¾” OD. A site

inspection will determine what length of tubing is

required for the installation.

Excess tubing must be either shortened at the job

site (recovering the holding charge, purging with

nitrogen when brazing and evacuating to 50

microns) or coiled up inside the building.

Installations with greater than 20 feet of vertical lift

between ice machine and the compressor require

a suction line trap. The suction line requires careful

handling and large radius bends to prevent kinking.

Roof mounting: To make installation easier the

compressor and condenser are designed to be

assembled together on the roof. Some

installations will require the use of a hoist to lift the

components to the roof.

Pad mounting: The compressor and condenser

may be located below the ice making section, up to

a limit of 15 feet.

Distance from unit: Limited to the length of the

available pre-charged tubing.

Elevation: CP unit limited to 35 feet above the ice

making section.

Compressor package: Electrical power must be

supplied to the compressor package. The remote

condenser fan motor takes its power from the

compressor package.

Ice making section location and attachment:

The 115/60 Hz ice making section is cord

connected and requires an outlet within 6 feet of

the installation.

Interconnecting wires: An interconnecting wire

harness is included with the CP unit. One end

plugs into the ice making section and the other into

the compressor package. The system will NOT

operate without this harness.

Exposed tubing: Minimize the amount of tubing

exposed outdoors.

Confirm Component Availability:

CME1386 or CME1686

CP1316

ERC1086 unless connecting to an approved

condenser coil.

Note: Only these condensers may be used. They

do NOT contain a headmaster valve. That valve is

in the Compressor Package. Do NOT use any

other Scotsman condenser. Do NOT use these

condensers on any other Scotsman remote

product.

Interconnecting tubing kit

Note: Check tubing integrity before assembly by

attaching a refrigeration compound gauge onto one

of each tube’s schrader valves. If there is pressure,

the tube is OK, if not it should be checked for

damage and leaks.

Bin or dispenser adapter

Eclipseä 1300, 1600

September 2003

Page 8

System Examples

The Eclipse system can be installed on a bin or

dispenser. The CP unit can be installed on either a

single circuit condenser or onto a coil in a separate

rack condenser.

Separate coils must be:

Scotsman approved

The correct size and capacity

New or not have been part of a system that

used mineral oil.

Eclipseä 1300,1600

September 2003

Page 9

System on Ice Storage Bin

System on Ice Dispenser

System Examples

A variation of the typical system set up is one that

uses a non-Scotsman condenser. In that case the

CP unit is NOT bolted to the condenser and a

RTE10 line set is used to connect the refrigeration

system to the condenser’s coil.

Eclipseä 1300, 1600

September 2003

Page 10

IMS on Bin, CP Unit Connected to Approved Central

Condenser Coil

Place Remote System

Roof preparation

Most installations of this system will place the

compressor package and condenser on the roof of

a building. The roof must be physically stout

enough to accept the load of the equipment and

the roofing material must be prepared to prevent

water leaks.

Follow local codes for the placement and

attachment of the equipment.

Location

The air cooled condensing unit assembly requires

unobstructed air flow to operate efficiently. A four

foot space between each intake side and a wall or

other cabinet is recommended. Provide at least 2

feet of space above the air cooled condenser for

proper air flow.

Do not place where the air cooled condenser will

pick up hot discharged air from an air conditioner

or other refrigeration system condensing unit.

Space must also be reserved for service on the

compressor package.

Roof Piercing:

The roof (or wall) must have a passage large

enough for the three pre-charged, pre-bent tubes

and the control wire to pass through. The minimum

recommended size is 4” ID. In most areas the

power supply may also pass through the same

passage. If there isn’t a passage one must be

created. In most cases this must be done by a

licensed and bonded roofer in order to maintain the

roof’s integrity.

Suggestions:

Hoist the compressor package and condenser to

the roof in separate loads.

Note: In most cases a mechanical lift, boom truck

or crane will be required to hoist the condensing

unit components.

Assemble the compressor package to the

condenser and mount both to either roof rails or

pressure treated4x4s.

Orient the assembled unit so that the unit’s mounts

are parallel to the pitch of the roof to allow water to

drain freely.

Do NOT place the unit directly onto roof rock.

Eclipseä 1300,1600

September 2003

Page 11

System Location

Limitations:

Distance: Limited to the maximum length of a

single pre-charged tubing kit, 75 feet.

Condensing Unit Elevation over Ice Making

Section: 35 feet.

Note: Elevations greater

than 20 feet require

installation of a suction line

trap at the 20 foot mark.

Ice Making Section

Elevation over Condensing

Unit: 15 feet.

Line Routing:

Allowed: One rise after a drop.

Allowed: One drop after a rise.

Not Allowed: More than one rise after a drop

Not Allowed: More than one drop after a rise.

Eclipseä 1300, 1600

September 2003

Page 12

22.87"

17.15"

40.35"

Condensing Unit Distance Schematic

Max Rise:

35 Feet

Max Drop:

15 Feet

Max Length -

Limit of Line Set

Condensing

Unit Located

Below Ice

Machine

Condensing

Unit Located

Above Ice

Machine

S-Trap

Route Tubing

Scotsman’s pre-charged tubing kits are pre-bent to

fit the connection path at the ice making section.

If the tubing is to be routed out the back, use

the double-bend ends.

If the tubing is to be routed out the back and

then up, use the ends with the single 90

degree bends.

Note: Units mounted flush against the wall require

refrigerant connections out the top, water supply in

from the top, power supply routed through the top

and drain routed to the left side.

Select the correct end to send to the roof.

The method or technique used to route the tube is

left to the installer. However, in many cases it is

easier to position the tubing inside the building first,

then feed the outside portion through the tubing

passage (pitch pot). Installation of tubing will be

easier if the suction line is run first, followed by the

liquid and vapor lines. Use of two persons is

suggested to prevent kinking of the tubing, long

runs may require three people.

Allow enough tubing to make large radius bends

from the roof passage to the compressor unit.

Do NOT leave excess tubing on the roof.

If a trap must be installed, the suction line

tubing must be cut apart to install it.

Identify the ice machine end of the tubing. Each

tube has one end formed to route through the

hole in the unit’s top.

Tape the ends of the vapor and liquid line tubes

together along with the interconnecting wire.

Extend the end of the interconnecting wire

about 2 feet beyond the end of the precharged

tubes and then tape it back onto the tubes.

Route the three tubes and the wire from the

roof, or other entrance, to the ice making

section’s planned position. Avoid uncoiling and

recoiling the tubing, as that can lead to kinks.

Support long runs of tubing with hangers.

Repair any tears in the tubing insulation,

especially those on the suction line that are

inside the building.

Shortening Tubing

The precharged tubing kits are available in a

variety of lengths, they should only be shortened if

absolutely necessary.

To Shorten Tubes:

1. Recover the 3 ounce R-404A holding charge

from each tube.

2. Cut out the required length of tubing, do not cut

the tubing right at the quick connects.

3. Attach nitrogen bottle to one quick connect and

a hose with a depressor to the other end, purge

nitrogen through each tube while brazing.

4. Remove nitrogen, evacuate to 200 microns.

Note: If tubes are connected to the IMS, evacuate

the vapor & suction lines to get the entire system.

Eclipseä 1300,1600

September 2003

Page 13

Suction

Vapor

Liquid

Suction

Vapor

Liquid

Ice Making Section

The CME1386 and CME1686 are similar in layout.

They differ in evaporator count, controller, float

stem and vapor inlet valve.

Major Components:

TXV - one feeding a refrigerant distributor

Water Pump - same for both models

Water Level Sensor - signals reservoir water level

to the controller

Controller - operates both the ice machine section

and the compressor unit.

Drain Valve - opens to allow pump to drain the

reservoir

Water Inlet Valve - 2.77 GPM solenoid valve that

opens to fill the reservoir

Low Side Access Valve - allows connection for

diagnosis of ice machine section refrigeration

operation. Not for recovery.

Liquid, Vapor and Suction

Connections - where the

pre-charged tubing kits

connect to.

Eclipseä 1300, 1600

September 2003

Page 14

Water

Pump

Water

Level

Sensor

Drain Valve

Water Inlet

Solenoid

Valve

Freezing

Compartment

Low Side

Access Valve

Vapor

Connection

Liquid

Connection

Suction

Connection

TXV

Controller

Front Ice

Sensor

Bin

Thermostat

Vapor Inlet

Valve

Compressor Package

Both compressor packages are similar in layout,

they only differ in compressor and charge.

Major Components:

CPR Valve - limits refrigeration pressures

inside the dome of the compressor.

Condenser By Pass Valve - opens during

harvest to allow discharge gas to flow to the

vapor line.

Headmaster - maintains a minimum

discharge pressure during freeze

Liquid Inlet Valve - Normally Open, closes

during harvest.

Receiver - stores liquid refrigerant for

freeze and provides vapor for harvest

Suction Access Valve - provides a place to

attach a refrigeration manifold for diagnostics

and recovery.

Eclipseä 1300,1600

September 2003

Page 15

CP Unit Refrigeration Connection ID

Power

Routing Hole

Vapor Line

Connection

24 volt comm line

Routing Hole

Liquid Line

Connection

Suction Line

Connection

Liquid from

Cond.

Discharge to

Cond.

Condenser

Wire Routing

Hole

CP Component Location

CPR Valve

Liquid

Access

Valve

Headmaster

Condenser By

Pass Valve

Pressure

Cut Out

Liquid Inlet

Valve

Receiver

Suction

Access

Valve

Condensing Section Assembly

(CP1316 to ERC1086):

1. Remove cartons from compressor package and

condenser.

2. Remove top from both units.

3. Remove front panel from CP unit.

4. Locate legs, secured to ERC unit.

5. Locate fasteners, inside junction box of ERC

unit.

6. Assemble rear legs to ERC using fasteners from

prior step.

7. Locate wire package in CP unit. Remove short

wires and two wire nuts.

8. Use wire & wire nuts from step 7 to connect to

the wires inside the junction box of the condenser.

Return junction box cover to its original position.

9. Place front of ERC on back flange of CP unit.

10. Secure CP unit to ERC.

11. Attach leg brace between ERC unit and CP

unit.

12. Route wires from condenser through hole in

back of CP unit to the CP unit control box.

13 Pull ERC female refrigerant connections

forward to engage male connections on CP unit.

14. Rotate swivel nuts to tighten refrigerant

connections. Use a back up wrench to hold female

connection to prevent tearing of the diaphragms.

15. Connect wire to T1 and T2 of the contactor.

Use the two wire nuts to connect the other end to

the two black wires in the condenser junction box.

16. Return tops to their original positions.

Eclipseä 1300, 1600

September 2003

Page 16

CP Unit Contactor, Three Phase Shown

Connect

Fan Motor

Leads

Connect

Power

Here

Rotate Swivel

Nuts to Connect

Condenser

System to

Compressor

Unit

Locate

Fastener

Package

Condensing Section Assembly

Alternate Assembly:

The CP unit may be connected to an approved

condenser coil in a central condenser rack. In

those cases, the CP unit must be connected to the

condenser coil using special kit RTE10.

Position the CP unit in its final spot. It must be

within 6 feet of the condenser coil connections.

Route tubing from kit RTE10 from the CP unit to

the condenser coil.

Connect tubing per the Coupling Instructions in this

manual.

No wire connection is required between the CP

unit at the condenser.

Note: Approved condensers must maintain power

to their fan motor at all times.

Note: For local codes requiring a pressure relief

valve: Recover charge and connect valve to

receiver liquid outlet tubing.

All Assemblies:

Route interconnecting control wire through proper

hole in side of CP unit and plug into the connection

on the bottom of the control box.

Route power conduit (liquid tight) and wires to the

hole in the side of the CP unit. Secure with the

proper type of connector.

Note: The power supply wires must be the correct

size and type per the National Electric Code.

Locate the nameplate on the CP unit for the

Voltage, Phase, Minimum Circuit Ampacity and

Maximum Fuse Size. Either fuses or HACR type

circuit breakers may be used.

Follow all Local, State and National Codes.

Connect power wires to the contactor, L1 and L2 if

single phase, L1, L2 and L3 if three phase. Note: If

there is a “wild leg” in the three phase power

supply place it on L3.

Connect electrical power to the CP unit.

Return front of CP unit to its original position.

Eclipseä 1300,1600

September 2003

Page 17

Control Wire Connection in CP Unit

Interconnecting

Control Wire Plug

CP Unit Contactor, Three Phase Shown

Connect

Power

Here

Connect

Fan Motor

Leads

Approved

Central

Condenser

Unit

Scotsman

Condensing

Unit

Ice making section:

Remove from carton.

Remove all panels.

Utility Connection Route:

Electrical: The unit is supplied with a power cord.

The power cord can be routed out the back, left

side or top. There is also an interconnecting control

wire that must be routed between the ice making

head and the CP unit. That wire can be routed out

the back or top.

Water Supply: The water supply can be routed

from the top, back or left side.

Drain: The drain can be routed out the back or the

left side.

Refrigeration Tubing: The tubing can be routed out

the top or the back.

Adapters:

In many cases an adapter kit will be required when

placing the head unit on a bin or dispenser. See

sales information for the correct kit. Place adapter

kit onto bin or dispenser top. If adapter does NOT

have gasket tape install tape such as Scotsman

part number 19-0503-04.

Attachment:

If the unit is a direct fit, place it on the bin. If the

unit is in a position that it need not be moved to

complete the installation, secure it to the bin with

the hardware provided with the head unit.

On some bins or dispensers it may be necessary

to drill small holes and use field supplied sheet

metal screws to secure the ice making head to that

bin, dispenser or adapter.

Control Wire

Plug the interconnecting control wire into the

harness at the back of the head unit’s electrical

box.

Eclipseä 1300, 1600

April 2003

Page 18

Ice Making Section Control Wire Connection

IMS Shown on Ice Dispenser

Control

Wire

Connector

Electrical Box in

Ice Making Head

Bin Thermostat - Routing

Install the bin thermostat after the ice making

head has been placed on the bin or dispenser.

Note: Dispensers may require special attention to

keep ice or agitator/sweep arm from moving the

thermostat from its installed position. Place the

head on the dispenser and install the thermostat

before connecting refrigerant tubing.

Before starting, remove the left side and front

panels and any baffle in the bin.

1. Locate bin thermostat bulb.

2. Route bulb thru routing tube (located behind the

reservoir).

3. Locate bin thermostat bracket.

4. Carefully position the thermostat bulb on the

bracket (see the diagram on the next page).

5. Fasten the bracket to the bottom of the ice

machine with the two 3-pronged knob head screws

supplied with the unit.

6. Pull back into the ice machine any excess

capillary tubing.

7. Return the baffle to the bin and continue with the

installation.

Note: If the machine is located at an altitude higher

than 2,000 ft., adjust the thermostat by removing

the plastic cover and rotating the adjustment screw

per the table.

Eclipseä 1300,1600

September 2003

Page 19

Bin Thermostat Altitude Correction Table

CW Turns of Range Screw (under plastic cover)

Feet Turns Feet Turns

2000 55

8000 340

4000 160

9000 385

6000 250

10000 405

Bin

Thermostat

Bulb

Thermostat

Bulb Routing

Tube

Bin Thermostat - Bracket & Bulb

Eclipseä 1300, 1600

September 2003

Page 20

Attach Thermostat Bulb to Bracket

Mount Bracket to Bottom of ice Head

Bracket

Thermostat

Capillary Tube

Insert Tip into

Hole

Snap Tube

Through Slot

Bulb

Page is loading ...

Scotsman CME1686RLS User manual

Brand: Scotsman

Model: CME1686RLS

Category: Ice cube makers

Type: User manual

This manual is also suitable for

CME1386RLS

Download PDF

report

Scotsman CME1686RLS User manual

This manual is also suitable for

Scotsman CME1686RLS User manual

Related papers

Other documents