Barco V6i User manual

Brand: Barco

Model: V6i

Type: User manual

V6i

Safety manual

R5905985/00

05/05/2015

Barco NV

President Kennedypark 35, B-8500 Kortrijk

Phone: +32 56.23.32.11

Fax: +32 56.26.22.62

Support: www.barco.com/en/support

Visit us at the web: www.barco.com

Printed in Belgium

1. Safety

1. SAFETY

About this chapter

Read this chapter attentively. It contains im portant information to prevent personal injury w hile installing your V6i display. Further-

more, it inc ludes several cautions to prevent damage to the V6i tile. E nsure that you understand and follow all safety guidelines,

safety instructions and warnings mentioned in this chapter before installing the V6i display. After this chapter, additional “warnings”

and “cautions” are given de pending on the installation procedure. Read and follow these “warnings” and “cautions” as well.

Overview

• Safety g uidelines

• Important safety instructions

• Important warnings

• Proper usage

1.1 Safety g uidelines

Personal protection

WARNING: Ensure you un derstand and follow all the safety guidelines, safety instructions, warnings and

cautions mentioned in this m anual.

WARNING: Be aware of suspended loads.

WARNING: Wear a hard hat to reduce the risk of personal injury.

WARNING: Be careful while wo rking with heavy loads.

WARNING: Mind your ﬁngers w h ile working with heavy loads.

Installation personnel

This installation must be performed by au thorized and qualiﬁed technical personnel only.

Accredited safety ofﬁcers m ust ensure the safety o f the site, construction, assembly, connection, use, dismantling, transport etc. of

such saf e ty crit ica l sys tems.

Notice on safety

This equ ipment is built in accordance w ith the requirements of the international safety standards IEC60950-1, EN60950-1,

UL60950-1 and CAN/CSA C22.2 No.60950-1, which are the safety standards of information technology equipmen t including

electrical bus iness equipment. These s afety standards impose im portant requirements on the use of safety critical co mponents,

materials and insulation, in order to protect the user or operator against risk of electric shock and energy haz ard and having access

to live parts. Safety standards also impo se limits to the internal and external temperature rises, radiation levels, mechanical stability

and strength, enclosure construction and protection against the risk of ﬁre. Sim ulated single fault condition testing ensures the

safety of the equipm ent to the user even whe n the equipment’s normal operation fails.

Caution

Installation should be performed on ly after y ou are thoroughly familiar with all of the prope r safety checks and installation instructions.

To do otherwise increases the risk of hazards and injury to the user.

R5905985 V6I 05/05/2015

1. Safety

Assembly parts are designed for intended use only in conjunction with V6i LED displays.

Do not modify and/or replicate any component. Barco uses spec iﬁc materials and m anufacturing processes in order to achieve part

strength. Consult Barco for assistance with c ustom applications.

Always follow B arco installation ins tructions. Contact Barco if you should have any question regarding the safety o f an application.

The manufacturer assum es no liability fo r incorrect, inadequate, irresponsible or unsafe as sem bly of s ystem s. The system must

comply with the local safety regulations regarding environmental conditions, solidity ﬁnal construction, etc…

Product care

Structural & mounting components should be kept dry, c lean, lubricated (only if recomm ended), coated properly, and otherwise

maintained in a manner consistent with part design. B arco products m ust be used in a manner consistent with their design and

inspected on a routine basis for security, wear, deformation, corrosion and any other circums tances that may affect the load handling

capability o f the part.

Barco recommends inspections at regular intervals for a ll installations and increasing in frequency for more critical installations. If

a part is found to have damage, which m ay cause a de crease in load capability, the part must be removed for service o r replaced

immediately.

Under n o circumstances are Barco parts repairable by anyone other than Barco.

1.2 Important safety instructions

Instructions:

• Read these instructions.

• Keep these instructions.

• Heed all warnings.

• Follow all instructions.

• Clean only with materials or chemicals that are inert, nonabrasive, noncorrosive and non-marking. C onsult the manufacturer

for f urther advice should any doubts exist regarding any cleaning procedure.

• Do not bloc k ventilation openings. Install in accordance with the manufac

turers instruction s.

• Do not install near any heat sources such as radiators, heat re gisters, stoves, or other app aratus (including ampliﬁers) that

produce heat.

• Do not defeat the safety purpose of the polarized or grounding type plugs/sockets. I f the provided sockets/plugs are dam aged

then replacement of the defective parts must be undertaken immediately.

• Protect the power/data cords from being walked on or pinched particularly at plugs, convenience receptacles, and the point

where they ex it from the apparatus. R eplace damaged power/data c ords im mediately.

• Only use attachments/accessories s peciﬁed by the manufacturer.

• Disconnect the pow er to this apparatus during lightning storms or provide suitable additional lightning p rotection. Unplug this

apparatus when unused for long period of time.

• Refer all servicing to qualiﬁed service technicians/personnel. Servicing is required when the appa ratus has been dam aged in

any way, suc h as power-supply cord or plug is damage d, the apparatus does not operate normally, or has been dropped.

• Use only with systems or p eripherals speciﬁed by the manufacturer, or sold with the apparatus. Use caution during lifting/moving

or transporting to a void damage by poss ible tipping.

• Do not us e dam aged goods. Rep lace damaged parts imm ediately.

1.3 Important warnings

Important warnings:

Risk of electric shock:

Do not open. To reduce the r isk of electric shock, do not remove cov er (or back). No user-serviceable parts inside. Refer servicing

to qua liﬁed service personnel.

Maximum and minimum ambient tem perature:

The max imum amb ient temperature for the LED wall is 40°C (104°F), the minimum temperature is 0°C (32°F).

High leakag e curren t:

The com bination of multiple tiles in an installation results in increased levels of leakage current. In order to avoid risk of electric

shock due to high leakage current, proper groundi

ng of the installation is required.

Risk of personnel injury:

Secure all tiles in the rack. As a supplementary s afeguard, and in order to protect against the risk of personnel injury, eac h tile

should be attached to the rack by a safety ca ble.

R5905985 V6I 05/05/2015

1. Safety

Flammable materials:

Keep ﬂammable m aterials away from the installation (such as curtains). A lot of energy is transferred into heat. The installation

should be such that the amount of air ﬂow required for safe operation of the equipment is not compromised. Proper ventilation must

be provided.

Risk of electric sho ck / Risk of ﬁre:

To protect against risk of ﬁre caused by overloading of power c ables:

• MAXIMUM 5 tiles may be connected in parallel in case of 110-180 VAC, 50-60Hz. Each power so urce cable s upplying ma ximum

5 tiles shou ld be protected by a circuit breaker or fuses rated 16 A / 250 VA C (15 A / 250 VAC in the US A and Canada).

• MAXIMUM 10 tiles m ay be connected in parallel in case of 180- 240 VAC, 50-60Hz. Each power source cable supplying max i-

mum 10 tiles should be pr otected by a circuit breaker or fuses rated 16 A / 250 VA C (15 A / 2 50 VA C in the USA and Canada).

Note that one V6i tile requires 100-240 VAC, 50-60 Hz.

Disconnect d evice:

When the appliance inlets o f the individual tiles are not a ccessible, the socket outlets s upplying the r ack shall be installed near the

equipment and be easily accessible, or a readily a ccessible gen eral dis connect device shall be incorporated in the ﬁxed wiring.

This equipm ent MUST be earthed:

In order to protect against risk of electric shoc k, the installation should be p roperly grounded. Defeating the purpose of the grounding

type plug will expose you to the risk of electric shock.

Power sys tem:

It is recommended to use a TN-S power distribution system (a power distribution system with a separate neutral and grounding

conductor) in order to avoid large ground current loops du e to voltage differences in the neutral conductor. The total electrical

installation should be protected by an appropriately rated disconnect switch, circuit breakers, over voltage pr otector and G round Fault

Current Interrupters. The installation shall be done according to the local electrical installation codes. In Europe special attention

should be given to HD 60364, H armon ization Docum ent for electrical installation of buildings. In Germ any VDE 0100 should be

adhered to. In America, special attention should be given to the National Electrical Code, ANSI/NFPA 70.

Mains cords:

The pow er cords delivered with this system have special properties for sa

fety. They ar e not user serviceable. If th e po w er cords are

damaged, replace them only with new ones. Nev er try to repair a power cord.

Data cables:

The data cables provided with this system have special properties for safety. They are not user serviceable. If the data cables are

damaged, replace them only with new ones . Never try to repair a data cable. Pe r requirements of the National Electrical Co de®

in the US A , the length o f a data cable must not exceed 42 m (140 feet). Avoid exposure of data cables to accidental contact with

lightning or power conductors.

1.4 Proper usage

Proper usage of V6i tiles

• Shipping crates m ay be stacked to a max imum of 2 crates high.

• No part of the V6i tile can come in contact w ith an y type of abrasive.

• No part of the V6i tile can com e in contact with any type of c orrosive substance.

• V6i tiles ar e to be used in environme nts meeting the oper ating speciﬁc ations.

• V6i tiles ar e not to be exposed to extreme localized heat or cold exceeding the temperature speciﬁc ations.

• V6i tiles are not to be exposed to any element or situation that will cause any part of the display to heat beyond what occurs

during normal operation. Such s ituations include (but are not limited to) lasers, ultrasonic vibration, or any type of substance

that prevents proper ventilation and he at radiation of the V6i tiles.

• Power c onnected to the V 6i tiles m ust meet the s peciﬁc ations outlined in the installation manual.

• Never place a V6i tile upo n a surface with the LEDs facing downwards. This to prev ent dam age to the LEDs and the shaders.

• No force can be applied to the LEDs. Any LEDs damaged due to mechanical stress are not covered by the warranty.

• Safety and functional features of the display cannot be defeated.

• Any failures must be imm ediately and appropriatel

y dea lt with. Failing equipm ent should not be left on a wall.

• Only Bar co cables s peciﬁed to be used with the V6i display are to be used to connect com ponents in an V6i wall. Furthermore,

care must be taken to connect signals only according to the installation manua l.

• V6i tiles are not to be u sed in the vicinity of an y equipment that is not C E and UL/ETL ce rtiﬁed.

• V6i tiles are not to be connec ted to any non-Barco equipment.

• V6i tiles can be cleaned only in ac cordance to the proc edures deﬁn ed in the installation manual.

• The V6i tile is equipped with two air ﬁlters. These ﬁlters must be replaced on a regular basis, depending on the environment

conditions of the tile. It is recommended to replace the ﬁlters every 6 mo nths o r a shorter period, depending on the local

environment.

R5905985 V6I 05/05/2015

Barco V6i User manual

Barco V6i User manual

Related papers

Other documents