Home Styles Consumer Assistance: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Tools required for assembly : Phillips screwdriver
Part List
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occurring to the wood parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
Hardware List
Wood Plug
10 pcs. (+2 extra)
Hex Wrench
1 pc.
Caster
Two with lock and
Two non-locking
4 pcs.
M3.5x25
Wood Screw (long)
32 pcs. (+1 extra)
Knob
2 pcs.
88 9100 001CN
Kitchen Cart
He
1
p
M4x25
Machine Screw
10 pcs.
(Please refer to the last pages of these
instructions for drawer assembly.)
J.
Base
1 pc.
M6x35
Head Cap Bolt (long)
14 pcs. (+1 extra)
Adjustable Pin
8 pcs. (+1 extra)
Small
Hex Wrench
1 pc.
t
M4x16
Wood Screw
for Caster
16 pcs. (+1 extra)
D.
Middle Panel
1 pc.
B.
Side Panel
1 pc.
E.
Back Panel
3 pcs.
A.
Side Panel
1 pc.
F.
Back Piece
2 pcs.
G.
Back Stretcher
1 pc.
H.
Front Stretcher
1 pc.
R.
Base Rack
1 pc.
O.
Door
1 pc.
T.
Drawer
3 pcs.
U.
Drawer
1 pc.
K.
Shelf
2 pcs.
L.
Handle Arm
2 pcs.
M.
Round Arm
1 pc.
M3.5x13
Wood Screw (short)
24 pcs. (+1 extra)
a
se
pc.
.
.
.
.
r
awer
.
helf
.
R
.
C.
Middle Panel
1 pc.
N.
Door
1 pc.
Q.
Side Rack
1 pc.
P.
Side Rack
1 pc.
I.
Front Rail
3 pcs.
S.
Pipe
3 pcs.
Pull Handle
4 pcs.
STEP 2
Attach Back Pieces (F) to Middle Panels (C)
and (D).
Attach Front Rails (I) to Middle Panels (C)
and (D).
IMPORTANT
* Do not tighten up all the screws and bolts until each part is properly assembled.
* You should keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future.
* Use a soft cloth between these parts and the fl oor.
Assembly Instruction 2 / 6
I
I
F
I
Locking Casters
Wood Screw for Casters
C
D
J
Non-Locking Casters
Figure 1
F
STEP 1
Attach 4X Casters to Base (J) with Wood Screws for Caster, with the
Locking Casters at the front as indicated by ‘Arrow’ sticker. (see Figure 1)
STEP 3
Attach unit to Base (J).
Attach Side Panel (A) to unit with Head Cap Bolts.
(see Figure 2)
ST
E
Atta
ch
Atta
ch
(
see
F
Assembly Instruction 3 / 6
STEP 4
Slide Back Panels (E) into the unit.
Attach Back Stretcher (G) and Front
Piece (H) to the unit with Head Cap
Bolts.
Attach Side Panel (B) with Head Cap
Bolts.
B
Head Cap Bolt
J
A
E
E
S
Q
E
G
H
Head Cap Bolt
Head Cap Bolt
Figure 2
STEP 5
Attach Side Rack (Q) to the unit with Head Cap
Bolts.
Slide Base Rack (R) and Pipes (S) to Side Rack
(Q).
Attach Side Rack (P) to unit with Head Cap Bolts.
S
R
S
P
STEP 8
Cover all holes with Wood Plugs.
(see Figure 3)
L
Assembly Instruction 4 / 6
STEP 6
Assemble Handle Arms (L) to Side
Panel (B) with Head Cap Bolts.
Slide Round Arm (M) into place.
STEP 7
Insert Adjustable Pins into
side panels and middle panels
at the desired level and slide
Shelves (K ) into place.
M
K
K
B
Figure 3
L
Head Cap Bolt
Wood Plug
Adjustable Pin
Wood Plug
T2
STEP 2
Slide T5 into the grooves in T3
and T4. Push T5 all the way
forward so it meets T1. (see
Figure 2)
Assembly Instruction 5 / 6
Drawer (T)
Part List
T2.
Back Part
3 pcs.
T3.
Side Part
3 pcs.
T4.
Side Part
3 pcs.
T5.
Base Part
3 pcs.
T1.
Front Part
3 pcs.
T5
T3
T4
T2
STEP 1
Attach T1 to T3 and T4, using
a Phillips screwdriver and
long wood screws (4X), tighten
halfway.
Attach T2 to T3 and T4 using
long wood screws (4X), tighten
halfway. (see Figure 1)
STEP 3
Insert short wood screws (6X)
into the pre-drilled holes in T5
and tighten. (see Figure 3)
STEP 4
Assemble Pull Handle
with Machine Screws.
(see Figure 4)
Tighten all screws used in drawer assembly.
MAKE SURE ROLLER
IS ON THE BACK
T3
T4
T1
T1
T5
T3
T1
Figure 1
Figure 2
Figure 4
Figure 3
T2
T4
T1
.
Front Part
T3
T4
Fi
g
ure
4
STEP 2
Slide U5 into the grooves in U3
and U4. Push U5 all the way
forward so it meets U1. (see Figure 2)
Assembly Instruction 6 / 6
Drawer (U)
Part List
U2.
Back Part
1 pc.
U3.
Side Part
1 pc.
U4.
Side Part
1 pc.
U5.
Base Part
1 pc.
U1.
Front Part
1 pc.
U5
U3
U4
U2
STEP 1
Attach U1 to U3 and U4, using
a Phillips screwdriver and
long wood screws (4X), tighten
halfway.
Attach U2 to U3 and U4 using
long wood screws (4X), tighten
halfway. (see Figure 1)
STEP 3
Insert short wood screws (6X)
into the pre-drilled holes in U5
and tighten. (see Figure 3)
STEP 4
Assemble Pull Handle
with Machine Screws.
(see Figure 4)
Tighten all screws used in drawer assembly.
MAKE SURE ROLLER
IS ON THE BACK
U2
U3
U4
U1
U1
U5
U3
U1
Figure 1
Figure 2
Figure 4
Figure 3
U2
U4
U1
.
Fr
on
t
Pa
rt
U2
Fi
g
ure
4
/
