BMW CPT 9000 Installation Instructions Manual

Brand: BMW

Model: CPT 9000

Type: Installation Instructions Manual

BMW CPT 9000 Installation Instructions

MY 2003 X5 (E53)

Page

September 2003

BMW of North America

Product Engineering Department

Instructions Part Number

01 29 0 391 028

1of 8

MY 2003 BMW X5 (E53)

(6 and 8 cyl. models)

With Option SA639

BMW CPT 9000 DIGITAL PORTABLE TELEPHONE

INSTALLATION INSTRUCTIONS

BMW CPT 9000 Installation Instructions

MY 2003 X5 (E53)

Page

September 2003

BMW of North America

Product Engineering Department

Instructions Part Number

01 29 0 391 028

2of 8

This manual has been prepared by BMW of North America to provide service technicians with the proper

instructions for installing the CPT 9000 Digital Portable Telephone into X5 (E53) vehicles equipped with

and without factory navigation .

These instructions were developed by the BMW of North America, Product Development Engineering

Department specifically for BMW vehicles and are not to be compared to any existing instructions for

vehicles other than BMW. No methods other than those specified in this manual are to be used to install

the digital telephone.

The instructions in this manual were complete and up to date at the time of issue. Any changes in the

vehicle, digital telephone or problems noted by the installation personnel should be reported to BMW

Product & Service Engineering Department along with VIN, manufacture date and as much detail as

possible.

PART NUMBER MATRIX

X5 (E53) CPT 9000 INSTALLATION KIT

parts to be ordered separately

Eject Box (CPT 9000) 84 11 6 931 836 **

TCU Installation Instructions E53 01 29 0 391 028

Bumper Antenna 84 11 1 470 326

BMW CPT 9000 Installation Instructions

MY 2003 X5 (E53)

Page

September 2003

BMW of North America

Product Engineering Department

Instructions Part Number

01 29 0 391 028

3of 8

Carefully read all instructions and Supplements before proceeding with installation. Those

instructions dealing with a stock part of the vehicle but not stated in detail, should be referenced

with information in the TIS section of the DIS tester. Left and Right are determined from the

driver’s seat.

PRE-INSTALLATION NOTES & GENERAL INFORMATION ON CPT 9000 PHONE

SYSTEM

• X5 (E53) vehicles are pre-wired for the CPT 9000 Digital Phone and have the telephone

antenna factory installed.

• The CPT 9000 System on the X5 (E53) functions as a fully integrated Portable Digital

Phone. In addition, for those vehicles equipped with factory navigation the CPT 9000

System will also function as a Mayday (Emergency) and Roadside Assistance “BMW

ASSIST “ Call System. Additional features include automatic “Mayday” call on airbag

deployment and vehicle theft alarm activation.

• The Telematics Control Unit (TCU) for the CPT 9000 Digital Phone replaces the Akira

TCU previously used with CPT 8000 Digital Timeport Phone. The TCU must be coded

via the DIS (or MoDiC) Version C25.0 for vehicle configuration and VIN data. See TCU

Coding on page 18.

• The CPT 9000 Digital Phone is available in both CDMA and TDMA versions. Both

versions are Tri-Mode, Dual Band phones, meaning they will operate in the following

modes: 1900MHz Digital (CDMA/TDMA), 800MHz Digital (CDMA/TDMA) or 800MHz

Analog (AMPS).

BMW CPT 9000 Installation Instructions

MY 2003 X5 (E53)

Page

September 2003

BMW of North America

Product Engineering Department

Instructions Part Number

01 29 0 391 028

4of 8

Eject Box Installation ( Into Center Sliding Armrest

)

Important: It is no longer necessary to remove the center console to install the phone

eject box. The vehicle harness now terminates inside the arm rest.

Open center armrest to expose cover for compartment. Reference illustration

S84 01 U57.

1. Remove the three 2.5mm allen head screws 1

2. Remove plastic trim cover 2 from underside of armrest.

BMW CPT 9000 Installation Instructions

MY 2003 X5 (E53)

Page

September 2003

BMW of North America

Product Engineering Department

Instructions Part Number

01 29 0 391 028

5of 8

Coin Tray removal

1. Reference Illustration 84 03 U139

Remove plastic tray insert from center of armrest.

Eject Box Installation

1. Reference Illustration 84 03 U140

Install eject box with front portion angled downwards then locking rear into place by rotating

down. Make sure eject box wiring does not interfere with the proper seating of eject box

BMW CPT 9000 Installation Instructions

MY 2003 X5 (E53)

Page

September 2003

BMW of North America

Product Engineering Department

Instructions Part Number

01 29 0 391 028

6of 8

Eject Box installation continued

Reference illustration 84 03 U141

Eject box installed and locked in place.

BMW CPT 9000 Installation Instructions

MY 2003 X5 (E53)

Page

September 2003

BMW of North America

Product Engineering Department

Instructions Part Number

01 29 0 391 028

7of 8

This illustration is a graphic representation of Eject box harness routed through armrest.

Exposed is an ELO connector and a Fakra cable connector.

NOTE; It is no longer necessary to disassemble armrest to install eject box.

Eject Box Installation Continued

• Connect eject box antenna coax with vehicle antenna coax

• Connect eject box 18 pin ELO connector to vehicles 18 pin ELO connector.

• Reinstall plastic cover (removed on page 6) over wire harness and connectors. To ensure a

proper fit be certain that all wires are clear from the covers seating area.

Note:

BMW CPT 9000 Installation Instructions

MY 2003 X5 (E53)

Page

September 2003

BMW of North America

Product Engineering Department

Instructions Part Number

01 29 0 391 028

8of 8

Pay special attention to the routing of the harnesses. The arm rest has to slide and therefore it

is important to secure cables in such a way as not to obstruct this action or damage harnesses

themselves. Take notice that the eject box harness is routed under the vehicle harness. This

assures proper positioning and secures the wiring.

Antenna

The installation of a secondary antenna is necessary if a handset is to be used in all X5 series

models

A bumper antenna is required P/N 84 11 1 470 326.

Preparation

Reference TIS repair manual for removal of rear bumper assembly.

Reference illustration S84 04 U76

Prepare bumper antenna (2) surfaces with 3M adhesion promoter 4298 (1) by wiping area (3)

Be sure that surfaces are clean prior to application of adhesion promoter.

Reference illustration S84 04 U78

BMW CPT 9000 Installation Instructions

MY 2003 X5 (E53)

Page

September 2003

BMW of North America

Product Engineering Department

Instructions Part Number

01 29 0 391 028

9of 8

Apply adhesion promoter to both sides of rear bumper where antenna will be mounted, make

sure surfaces are clean prior to applying adhesion promoter.

Reference illustration S84 04 U77

After peeling away one side of the orange plastic from double sided foam tape (2), (included

with antenna kit) apply tape to antenna pressing and holding firmly in place for approximately 15

seconds.

Installation of bumper antenna

Position antenna (1) inside of rear bumper

BMW CPT 9000 Installation Instructions

MY 2003 X5 (E53)

Page

September 2003

BMW of North America

Product Engineering Department

Instructions Part Number

01 29 0 391 028

10of 8

Peel away orange plastic strips (2) and position antenna squares on the area previously treated

with adhesion promoter.

Reference illustration S84 04 U77

Install antenna with two coax cables in the left side of the bumper . Position antenna then press

and hold firmly for approximately 15 seconds. Route and secure cables along inner top side of

bumper . Locate entry point for antenna coax cable ( rubber grommet)

Route cable into vehicle and connect to coax that runs to eject box

NOTE

The Coax cable from the eject box may be wrapped and tucked in behind other harnesses or

tied back over left side wheel well area.

Programming

Because of roadside and emergency calls, the full vehicle identification number must be

programmed into the TCU. Failure to program the number in will result in the emergency call

center not being able to recognize the owner of the vehicle. Although the vehicles location will

still be transmitted.

After complete installation of eject box , TCU requires to be programmed via DIS Tester.

Please refer to S.I.B. 84 14 01 for detailed information programming Customer Assistance and

BMW center phone numbers.

BMW CPT 9000 Installation Instructions Manual

BMW CPT 9000 Installation Instructions Manual

BMW CPT 9000 Installation Instructions Manual

Related papers

Other documents