Lenco LED-3213 Operating instructions

Operating Instruction

Please read these instructions before operating

your

set and retain them for future reference.

LED COLOR TV

EUCY00-H249

LED-3213

WWW.LENCO.COM

PRECAUTION

1.

Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. This apparatus with CLASS construction .

6. Do not use this apparatus near water, the apparatus shall not be exposed

to dripping or splashing and that no objects lled with liquids, such as

vases, shall be placed on the apparatus.

7. Clean only with dry cloth.

8. Do not install this apparatus in windtight places such as the wall-unit. Do

not block any ventilation openings.

9. Do not install near any heat sources such as radiators, heat registers,

stoves, or other apparatus (including ampliers) that produce heat.

10. Do not defeat the safety purpose of the polarized or grounding-type plug.

A polarized plug has two blades with one wider than the other. A grounding

type plug has two blades and a third grounding prong. The wide blade or

the third prong are provided for your safety. If the provided plug does not

t into your outlet, consult an electrician for replacement of the obsolete

outlet.

11. Protect the power cord from being walked on or pinched particularly at

plugs, convenience receptacles, and the point where they exit from the

apparatus.

12. Only use attachments/accessories specied by the manufacturer.

13. Use only with the cart, stand, tripod, bracket, or table specied by the

manufacturer, or sold with the apparatus. When a cart is used, use caution

when moving the cart/apparatus combination to avoid injury from tip-over.

14. Unplug this apparatus during lightning storms or when unused for long

periods of time.

15. Refer all servicing to qualied service personnel. Servicing is required

when the apparatus has been damaged in any way, such as power-supply

cord or plug is damaged, liquid has been spilled or objects have fallen into

the apparatus, the apparatus has been exposed to rain or moisture, does

not operate normally, or has been dropped.

Attention:

Motionless picture might cause permanent destruction to the display.

Be sure not to display motionless picture on the LE D TV for more than•

2 hours, because it would cause picture remnants to appear, which is

called "screen burns". To avoid such picture remnants, please decrease

the "contrast" and "brightness" of the display when displaying motionless

picture.

While watching TV program in 4:3 size mode for a long time, there would•

be traces on the edge of the screen's left, right and center parts because

of different transmition of the light on the screen.Similar impact on the

screen will occur when playing DVD or connecting games control. Products

destroyed by these reasons can't be guaranteed for maintenance.

It might cause picture remnants to display electronic games and motionless•

picture of PC more than a period of time.To avoid such effect, please

decrease the "contrast" and "brightness" when displaying motionless

picture.

CAUTION

W

here the MAINS plug or an appliance coupler is used as the disconnect device,

the disconnect device shall remain readily operable.

CAUTION

These servicing instructions are for use by qualied service personnel only. To

reduce the risk of electric shock, do not perform any servicing other than that

contained in the operating instructions unless you are qualied to do so.

CAUTION

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type.

Batteries shall not be exposed to excessive heat such as sunshine, re or the

like.

Used batteries should not be thrown into the garbage can, please leave them

at an appropriate depot.

IMPORTANT INFORMATION

If a television is not positioned in a sufciently stable location, it can be potentially

hazardous due to falling. Many injuries, particularly to children, can be avoided

by taking simple precautions such as:

● Using cabinets or stands recommended by the manufacturer of the

television.

● Only using furniture that can safely support the television.

● Ensuring the television is not overhanging the edge of the supporting

furniture.

● Not placing the television on tall furniture (for example, cupboards or

bookcases) without anchoring both the furniture and the television to a

suitable support.

● Not standing the televisions on cloth or other materials placed between

the television and supporting furniture.

● Educating children about the dangers of climbing on furniture to reach

the television or its controls.

The each USB terminal should be loaded with 0.5 A under normal operation;

Do not attach candle to accessible opening area, to avoid flammable foreign

material from entering the TV

●

Minimum distances around the apparatus for sufficient ventilation;

The ventilation should not be impeded by covering the ventilation openings

with items,such as newspapers,table-cloths,curtains,etc.;

No naked flame sources,such as lighted candles,should be placed on the

apparatus;

Attention should be drawn to the environmental aspects of battery disposal;

The use of apparatus in tropical and/or moderate climates.

●

Put the TV in the environment of moderate temperature,not to lay aside the

Air Conditioner outlet or stove to avoid damage.

Use both hands when carrying TV, make TV suffer stable outside force.

●

Place the TV on a firm and flat surface,leaving a space of at lease 10cm around

the set and 30cm from the top of the set to the wall or cabinet.Ensure the TV is

positioned close to the wall to avoid it falling when pushed.

To avoid the TV overturning,when installed,it must with screw through

screw hole on the base for fixing

TV on the desk

Screw hole

Top view

●

When you turning the TV set,do not hold the top side of

the TV set ,you

should hold the bottom side .

●

When you lifting the TV set,do not use one hand to handle it,you

shoud lift the TV set by two hands.

1

CONTENTS

1. Connection and Preparation of TV

.............................................

1.1 Accessories .........................................................................

2

1.2 Installation of Stand.............................................................

2

1.4 Keys and Interfaces.............................................................

3

1.5 Remote Control....................................................................

1.6 Installation of Batteries......................................................... 5

2. Basic Operation..........................................................................

5

2.1 Power ON/OFF.....................................................................

5

2.2 Setting of Standby Mode

......................................................

2.3 Selection of Input Mode........................................................

3. Select input source ....................................................................

..........................................................................

................................................................

.......................................................................

........................................................................

7. T

echnical Speciication................................................................

8. Supported Signal Modes............................................................ 25

9. Simple Troubleshooting .............................................................

26

.....................................................................

1.3 Installation of Wall Mount Kit(Optional)................................

LE D COLOR TV

5.1 Picture menu

4. First time setup

5. Main Menu Operation

5.2 Sound menu

5.3 Channel menu

5.4 Lock system menu...............................................................

5.5 Setup menu..........................................................................

6. USB Operation ..........................................................................

6.1 Photo...................................................................................

6.2 Music...................................................................................

6.3 Movie...................................................................................

6.4 Text......................................................................................

2

22

23

2

4

5

6

7

8

10

12

16

17

22

24

Service and support ...................................................................

10.

WEE...........................................................................................

11.

CE..............................................................................................

12.

27

28

LE D COLOR TV

3

The design and specication takes actual

products as the standard

1.4 Keys and Interfaces

LE D COLOR TV

󱍃 󱍄

󱍅

󱍇

󱍈 󱍉

󱍆

23

22

VIDEO R

L

AV I N

RF IN

PC(VGA)

PC AUDIO

EARPHONE

HDMI3

USB

HDMI1 HDMI2

COAXIAL

SCART

YPbPr IN

CI

24

25

1.

Remote sensor

window

2.

Power indicator

3. Speaker

4.

Power switch

5.

Menu key

6.

Program “

+

”

key

7. Program “ ” key

8. Volume “

+

” key

9.

Volume “

-

”

key

10.

Source key

1

1.

Standby

key

12.

Power plug input

13. AV input

20 .

HDMI1

19.EARPHONE output

17.RF input

21.HDMI2

15.PC AUDIO input

24.USB

25.Coaxial

14.Scart input

16.PC(VGA) input

22.HDMI3

-

18.YPbPr IN

23.CI card

12

4

1.5 Remote Control

1. STANDBY(

): Standby turn on and off.

2. SOURCE: Select the signal source.

3. 0~9: Continue to press the keys to select

a channel.

4. DISPLAY: Display the information of

current video and audio.

5. RECALL: Return to previous channel.

20.TIMESHIFT:DTV mode time shift.

23. RECORD:DTV mode record data USB disk.

22. FAV.LIST: Favorite channel list

10.

VOL+:

Increase the volume.

11. CH∧

: Select the channel forward.

12. MUTE: Mute sound.

13.

VOL-: Decrease the volume.

14. CH∨

: Select the channel backward.

15. MENU: Enter or exit menu.

16. EXIT:Exit current function.

17.

, ,

,

key: The menu item selection.

18.

ENTER: Conrm or enter.

9. S.MODE: Select the sound mode.

MEDIA mode: Press one time to pause,

press again to playback.

21. ASPECT:Select picture size.

8. P.MODE: Select the picture mode.

24. SUBTITLE:DTV mode select subtitle mode.

7. TV/RADIO:Select the TV or Radio mode.

25. AUDIO: Select TV audio mode.

30. RED: Access the red item or page.

31. BLUE: Access the blue item or page.

32. GREEN: Access the green item or page.

33. YELLOW: Access the yellow item or

page.

FREEZE

P.MODE

TIMESHIFT

AUDIO

SUBTITLE

RECORD

FAV.LIST

SUBPAGE

INDEX

HOLD

REVEAL

EXIT

MEDIA mode: Fast Backward

MEDIA mode: Next

MEDIA mode: Fast Forward

MEDIA mode: Previous.

26.

INDEX: Display the index page.

27. SUBPAGE: Enter the sub page mode.

28. HOLD: Hold the current page.

29. REVEAL: Reveal the hidden information.

S.MODE

TV/RADIO

TXT

19. TXT: Enter or exit teletext

6. FREEZE: Freeze the picture.

SOURCE

STANDBY

MIXMIX SIZESIZE

CANCELCANCEL

LE D COLOR TV

ASPECT

5

2. Basic Operation

2.1 Power ON/OFF

- Connect the power cord to the AC input. Insert the power cord into the

appropriate socket.

- Press the Power switch to switch on the TV, then press Power button to

turn on the unit.

- Press the Power switch again to switch off the TV.

Note: After switch off the TV, please don’t immediately re-open the

power switch ,should be delayed one minute more to re-open the

power switch.

2.2 Setting of Standby Mode

- Press ( ) button to turn on the unit.

- Press ( ) button again to return the display to standby mode. The

power indicator turns red.

- Be sure not to set your TV in standby mode for a long period of time.

2.3 Selection of Input Mode

This set has different signal source modes, you may continue to press the

Source button to select a signal source.

1.6 Installation of Batteries

1. Open the back lid of the remote control.

2. Install two 7#(AAA)1.5V batteries.

Ensure the correct polarity of the batteries.

3. Cover the back lid.

Please take out of the batteries from the remote

control for long time of no use.

If the remote control doesn't work properly,

please carry out the following checks.

- Check the TV is turned on.

- Check the polarity of the batteries are correct.

- Check the batteries are not drained.

- Check the power supply is normal or the power cord

is correctly connected.

- Check there are no special uorescent light or neon

light around.

LE D COLOR TV

Select input Source

Press SOURCE button to display the input source list,

Press  /  or SOURCE button to select the input source you want to,

Press ENTER button to enter the input source,

Press EXIT button to quit.

6

LE D COLOR TV

Source

ATV

AV

YPBPR

HDMI 1

HDMI 2

HDMI 3

PC

USB

SOURCE:Exit

SCART

4. First Time Setup

Connect an RF cable from the TV’s input called “RF-In” and to your TV Aerial socket.

OSD Language

Press  /  button to select the language to be used for menus and message.

Mode Setting

Press  /  button to select mode.

Country

Press  /  button to select the country you want to.

Tuner Type

Press  /  button to select Air or Cable.

Auto Scan

Press  /  button to select Mode: DTV+ATV, DTV, ATV.

Auto Tuning Status

First tuning digital, press MENU button to skip digital tuning, Second tuning analogue, press MENU

button to skip analogue tuning.

First Time Setup

7

LE D COLOR TV

5. Main Menu Oper

ation

5.1 Picture Menu

P

ress MENU button to display the main menu.

Press  /  button select PICTURE in the main menu, then press ENTER /  to enter.

1. P

ress  /  button to select the option that you want to adjust in the PICTURE menu.

2 Press Enter/ /  button to adjust.

3 After  nishing your adjustment, Press MENU button to save and return back to the previous menu.

Picture MODE

Press  /  button to select Picture Mode, then press  /  button to select.

Brightness/Contrast/ Sharpness/Saturation/Hue

Press  /  button to select option, then press  /  button to adjust.

Brightness Adjust the optical  ber output of the entire picture, it will e ect the dark region of the

picture.

Contrast Adjust the highlight intensity of the picture, but the shadow of the picture is invariable.

Sharpness Aadjust the peaking in the detail of the picture.

Saturation Adjust the saturation of the color based on your own like.

Hue Use in compensating color changed with the transmission in the NTSC code.

Color Temp

Change the overall color cast of the picture.

Press  /  button to select Color Temp, then press  /  button to select Standard/Cool/Warm.

Standard Produces a vivid image.

Cool Produces a gentle blue-hued image.

Warm Produces a red-hued image.

Aspect Ratio

Press  /  button to select Aspect Ratio, then press  /  button to select.

Auto Automatically adjust Aspect Ratio based on TV size and TV program.

Full/4:3 /Zoom1/Zoom2 To select the available display format.

PC Setting

Press to select PC source.

Press MENU to enter the main menu, then press  /  button to select PICTURE menu.

Press ENTER /  to enter and press  to select PC Setting.

Main Menu O

peration

(

Available Picture mode: Standard, Mild,Personal,Dynamic).

8

LE D COLOR TV

SOURCE

Main Menu Operation

Press  /  button to select PC Settings, then press  /  button to adjust.

Auto Adjust Press MENU /  button to adjust to the screen automatically to the optimal position of

the picture.

H Position Adjust the horizontal position of the picture.

V Position Adjust the vertical position of the picture.

Phase Minimize horizontal distortion.

Clock Minimize vertical stripes in the screen image.

Screen Mode

Press  /  button to select HDMI Mode, then press  /  button to select Auto, Video or PC.

It is available in HDMI Input only.

Advanced Settings

Adjust advanced video features to  ne tune the picture.

Press  /  button to select Advanced Settings, then press Enter /  button to enter sub-menu.

NR

Set options to reduce video noise.

Press  /  button to select NR, then press  /  button to select.

O Select to turn o video noise detection.

Week Detect and reduce low video noise.

Medium Detect and reduce moderate video noise.

Strong Detect and reduce enhanced video noise.

Mpeg NR

Set options to reduce MPEG noise.

Press  /  button to select Mpeg NR, then press  /  button to select.

O Select to turn o MPEG noise detection.

Week Detect and reduce low MPEG noise.

Medium Detect and reduce moderate MPEG noise.

Strong Detect and reduce enhanced MPEG noise.

Dynamic Contrast

Automatically adjust picture detail and brightness.

Press  /  button to select Dynamic Contrast, then press  /  button to select.

(Available Dynamic Contrast: O , Week, Medium, Strong).

9

LE D COLOR TV

Main Menu Operation

5.2 Sound Menu

Press MENU button to display the main menu.

Press  /  button select SOUND in the main menu, then press ENTER /  to enter.

1. Press  /  button to select the option that you want to adjust in the SOUND menu.

2. Press Enter/ /  button to adjust.

3. After  nishing your adjustment, Press MENU button to save and return back to the previous menu.

Sound Mode

Press  /  button to select Sound Mode, then press  /  button to select.

Treble/Bass/Balance

Press  /  button to select option, then press  /  button to adjust.

Treble Adjust the treble e ect. Increases or decreases high-pitched sounds.

Bass Adjust the bass e ect. Increases or decreases lower-pitched sounds.

Balance Adjust the balance between left and right speakers to adapt to your listening position.

Surround Sound

Press  /  button to select Surround Sound, then press  /  button to select On or O .

EQ Setting

Adjust the curve of 7 bands equalizer.

Press  /  button to select EQ Setting, then press Enter /  button to enter sub-menu.

EQ Mode

Press  /  button to select EQ Mode, then press  /  button to select.

(Available EQ mode: O , Rock, Pop, Jazz, User).

AVL

Set the auto volume control.

Press  /  button to select AVL, then press  /  button to select On or O .

Standard

(Available Sound mode: Music, Personal, Movie).

Sound Sound

Sound Mode

10

LE D COLOR TV

Main Menu Operation

SPDIF

Press  /  button to select SPDIF, then press  /  button to select O / Auto / PCM.

Audio Description

Press  /  button to select Audio Description, then press Enter /  button to enter sub-menu.

Mode

Press  /  button to select Mode, then press  /  button to select On or O .

When the mode is On, Volume can be adjust by users.

Sound Type

Press  /  button to select Sound Type, then press  /  button to select.

(Available Sound Type: Stereo, Dual I, Dual II, Mixed).

11

LE D COLOR TV

Main Menu O

peration

5.3 Channel Menu

P

ress MENU button to display the main menu.

Press  /  button to select CHANNEL in the main menu, then press ENTER /  to enter.

1. P

ress  /  button to select the option that you want to select in the CHANNEL menu.

2. Press Enter button to enter sub-menu.

3. Press MENU button to return back to the previous menu.

Tuner Type

Press  /  button to select Tuner Type, then press  /  button to select Antenna or Cable.

Auto Scan

Press  /  button to select Auto Scan, then press Enter /  button to enter sub-menu.

Tuner type is Antenna Tuner type is Cable

C

ountry

Press  /  button to select country

Mode

Press  /  button to select Mode: DTV+ATV, DTV, ATV.

Scan Type

Press  /  button to select Scan Type: Advanced, Quick, Full.

Network ID

Press  /  button to select Network ID: Auto or enter digital numbers.

Frequency

Press  /  button to select Frequency: Auto or enter digital numbers.

Symbol Rate

Press  /  button to select Symbol Rate: Auto or enter digital numbers.

Start

Press Enter /  button to start the auto searching.

It will search digital channels  rst, then analog channels.

Before execute auto channel search, please con rm your antenna type is Air or Cable.

Wrong setting of Signal Type maybe cause  nding no channel. Found numbers do not include

encryption programs.

12

LE D COLOR TV

Main Menu O

peration

Manual S

can

Press  /  button to select Manual Scan, then press Enter /  button to enter sub-menu.

Digital Manual S

can

Press  /  button to select Digital Manual Scan, then press Enter /  button to enter sub-menu.

Tuner type is Antenna Tuner type is Cable

Netw

ork ID

Press  /  button to select Network ID: Auto or enter digital numbers.

Frequency

Press  /  button to select Frequency: Auto or enter digital numbers.

Symbol Rate

Press  /  button to select Symbol Rate: Auto or enter digital numbers.

Modulation

Press  /  button to select Modulation: Auto, 16QAM, 32QAM, 64QAM, 128QAM, 256QAM.

Start

Press Enter /  button to start the channel searching.

Analog Manual Scan

Press  /  button to select Analog Manual Scan, then press Enter /  button to enter sub-menu.

13

LE D COLOR TV

Main Menu Operation

Analog Scan

Press  /  button to select Analog Scan.

Color System

Press  /  button to select Color System: Auto, PAL or SECAM.

Sound System

Press  /  button to select Sound System: Auto, DK, BG, I or L.

Modulation

Press  /  button to select Modulation: Auto, 16QAM, 32QAM, 64QAM, 128QAM, 256QAM.

AFC

Automatic Fine tuning.

Press  /  button to select On or O .

Start

Press Enter /  button to start the channel searching.

14

LE D COLOR TV

Channel to save CH001

BG

Searching 48.25 MHz...

Channel to save CH001

BG

Main Menu Operation

Channel Edit

Press  /  button to select Channel Edit, then press Enter /  button to enter sub-menu.

The three colored keys are the shortcut key for programming the channel.

First press  /  to highlight the channel you want to delete or move or skip, then:

- Press the Red button to delete the channel.

- Press the Green button to skip the select channel.

- (Your TV set will skip the channel automatically when using CH+/- to view the channels.)

- Press the Blue button to to set the channel to moving state. Then press  /  to move it to the

position you want to put.

Common interface

Press  /  button to select Common interface, then press Enter button to enter sub-menu.

Only available when there is CI card under DTV.

Signal Information

Press  /  button to select Signal Information, then press the Enter button to see the detail

information about the signal. Only available when there is signal under DTV.

15

LE D COLOR TV

Page is loading ...

Lenco LED-3213 Operating instructions

Lenco LED-3213 Operating instructions

in other languages

Related papers

Other documents