Quadratec Mirror Relocation Bracket Kit Installation guide

Type
Installation guide
The Trusted Source
®
Mirror Mover Kit
for Jeep Wrangler ’97-’06 (TJ/LJ)
Installation and Instruction Manual
#13125.0201
REQUIRED TOOLS:
Safety Glasses
1/4” Drive Ratchet
1/4” Drive Extension
3/8” Drive Ratchet
T20 Torx Screwdriver
for door check strap footman loop removal
T27 Torx Socket 1/4” Drive
for mirror bolts removal
T40 Torx Socket 3/8” Driver
for removal of windshield bracket bolts
5/32” Hex Key
for installing new mirror hardware and
button head cap screws
3/16” Hex Key
for installing new windshield bracket bolts
7/16” Combination Wrench
KIT CONTENTS LIST:
Mirror Relocation Brackets:
Passenger Side (1)
Driver Side (1)
Adjustable Door Check Straps (2)
Hex Button Head Cap Screws:
A. 5/16 - 18 x 1 (4)
B. 1/4 - 20 x 1 (6)
Hex Button Head Cap Screws:
C. 1/4 - 20 x 3/8 (6)
Hex Head Lock Nuts:
D. 1/4 - 20 (6)
READ ALL SAFETY MESSAGES AND UNDERSTAND ALL
INSTRUCTIONS AND PROCEDURE NOTICES BEFORE
ATTEMPTING TO INSTALL OR USE THIS PRODUCT.
(x4)
(x6)
(x6)
(x6)
A
B
C
D
Mirror_Mover_INST_UPDATE.qxp_A4 4/5/17 3:41 PM Page 1
04052017154205
The Trusted Source
®
2
Overview:
Quadratec Mirror Mover Kits are designed to effectively relocate the side view
mirrors from the doors to the body of the vehicle know as the “A” pillars. This
enables convenient door removal without loosing the mirrors. Mirrors are a safety
requirement. Never operate a vehicle that does not have adequately installed side
view mirrors.
Original stock mirror location
READ ALL SAFETY MESSAGES AND ALWAYS WEAR
SAFETY GLASSES WHEN WORKING WITH TOOLS.
New location with mirror movers
Mirror_Mover_INST_UPDATE.qxp_A4 4/5/17 3:41 PM Page 2
04052017154205
The Trusted Source
®
3
Step One: Mirror Removal
Put on safety glasses. Remove the three Torx screws that attach each mirror to the ve-
hicle using a T27 Torx socket. Install three hex button head cap screws (1/4-20x3/8)
into the tapped holes on both sides to keep moisture and debris out and provide a fin-
ished look. Paint bolt heads if desired with available touch up paints.
Step Two: Adjustable Door Check Strap Installation
The existing factory door check straps allow the doors to swing open far enough to
come in contact with relocated side view mirrors. By replacing your door check
straps with the included adjustable versions, this problem can be eliminated.
Remove footman loops on the doors using a T20 Torx bit tool and install adjustable
check straps. We recommend starting with the 5th slot from the door’s footman loop.
T27 Torx Socket -
1/4” drive ratchet
with extension
Install three button head cap
screws (1/4 - 20 x 3/8)
per side as shown
5/32” Hex Key
Remove the factory
door check strap
Install adjustable
door check straps
at the 5th slot
T20 Torx
Screwdriver
Mirror_Mover_INST_UPDATE.qxp_A4 4/5/17 3:43 PM Page 3
04052017154407
The Trusted Source
®
4
Step Three: Mirror Relocation Bracket Installation
Remove the two Torx screws shown that attach each windshield frame bracket
using a T40 Torx socket. Place the appropriate mirror relocation bracket to correct
left or right hand side and attach each bracket using two hex button head cap
screws (5/16-18x1). Note: bottom fastener can be reached through the mirror bolt
hole shown or through the side of the bracket. Using a 3/16” hex head key, tighten
each fastener firmly. Re-check for tightness after both fasteners have been installed.
Step Four: Mirror Installation
Place the corresponding mirror onto the
relocation bracket and fasten each mirror
to its bracket using three hex button head
cap screws (1/4-20x1) and three 1/4-20
hex lock-nuts for each. Make sure all fas-
teners are tight and adjust both mirrors
for safety. Make sure all fasteners are
secure and adjust the door swing so it
checks before it hits the mirror.
If you have a question specific to your
purchase, our customer service staff is
standing by. Call toll free: (800) 745-6037
or visit our #1 rated website at
www.quadratec.com
© Quadratec, Inc. 2017
All Rights Reserved. Version 4.5.17
#12999.9009
T40 Torx Socket -
3/8” drive ratchet
Install two hex button
head cap screws
(5/16 - 18 x 1)
per side as shown
3/16”
Hex Key
5/32”
Hex Key
7/16” Combination Wrench
Hex button
head cap
screws with
lock nuts
Only remove
these two
bolts per side
Mirror_Mover_INST_UPDATE.qxp_A4 4/5/17 3:43 PM Page 4
04052017154408
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Quadratec Mirror Relocation Bracket Kit Installation guide

Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI