SCE SCE-ETHCK Installation guide

Brand
SCE
Model
SCE-ETHCK
Type
Installation guide
DIN Rail mounng clip
Converter kit assembly
DIN6797 A5.3 toothed washer
DIN7985 M5x8mm screw
SCE-ETHCK Manual
Assembly Instrucons:
For “DIN Rail mounng” x the two DIN Rail clips
supplied with this kit as shown below.
For “Panel Mounng” use the 1:1 drilling template on
page 2.
485-
485+
V-
V+
12
34
HDR-15-24
BF-430
RJ-45 port
A
Gnd
B
485
RS485
3-pole
connector
on A/C unit
Cat 5e cable
to TCP/IP
network
Switch
set to
RS485
85~264VAC
47~63 Hz
N
L
RS485 wiring
requirements
to be
determined
according to
installation
environment.
24VDC
• Components to be connected as shown on the wiring diagram.
• Instrucons on how to congure this converter can be found on the “BF430 Setup” document
(Doc. No. RDTG-2103) which can be downloaded from the Technical Documents secon on our website or
directly accessed by scanning the QR code below.
• Informaon and instrucons on how to communicate to the unit through MODBUS can be found in the
“MODBUS Communicaton Datasheet” (Doc. No. RDTG2001) which can be downloaded from the Technical
Documents secon on our website or directly accessed by scanning the QR code below.
Notes:
Ethernet
Interface
RS485 connection
Power
Working temperature
Working humidity
Dimensions (W:H:D)
Mounting
IP mode
IP address
Subnet mask
Default gateway
Primary DNS
Device name
Login username
Login password
Static IP
192.168.168.125
255.255.255.0
192.168.168.254
168.95.1.1
“CHIYU”
“admin”
“admin”
10/100Base-T/Tx, Automatic MSI/MDI-x port
RJ45 jack
Data +/-, Max. cable length 1200m
3 W
0~65 °C (32~149 °F)
20~90% RH, non-condensing
170x70x65 mm (6.2x2.8x2.6 in)
DIN Rail / Panel
Default BF 430 Conguration:
Technical Data:
https://www.saginawcontrol.com/instman/modbus-table.pdf
Modbus table
https://www.saginawcontrol.com/instman/sce-ethck-setup.pdf
SCE ETHCK setup
Assembly outline
Assembly outline
58 [2.28]
154 [6.06]
Ø4.5 [Ø0.18]
70 [2.76]
170 [6.69]
Drilling template for panel mounted assembly
Dimensions in mm [inch]
is instruction sheet contains information and instructions to enable the user to work safely, correctly
and economically on the product. e information, data and instructions contained in this instruction
sheet are current at the time of going to the press. We reserve the right to make technical changes to the
product in the course of its development. erefore, no claims can be accepted for previously delivered
products based on the information, diagrams or descriptions contained in this instruction sheet. No
liability can be accepted for damage and production caused by:
• Disregard of the instruction sheet
• Operating error
• Inappropriate work on/with the product
• e use of non-specied spare parts and accessories
• Unauthorized modications or changes to the unit by the user or his personnel.
e supplier is only liable for errors and omissions as outlined in the guarantee conditions contained in
the main contractual agreement. Claims for damages on any grounds are excluded. e product can only
be installed and maintained by technical competent and qualied personnel, using only supplied material
according to the supplied instructions. Only specialized personnel are allowed to maintain the product.
It must be ensured that during maintenance, the product is disconnected from the electrical supply. is
product is not intended for household use. e electric equipment meets the valid safety regulations. One
can nd dangerous voltages (above 50 V AC or above 100 V DC) at the power supply of this product.
sce-ethck-manual.pdf
Relevant Links:
  • Page 1 1
  • Page 2 2

SCE SCE-ETHCK Installation guide

Brand
SCE
Model
SCE-ETHCK
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents