Tele Radio R8-20 Operating instructions

Brand: Tele Radio

Model: R8-20

Type: Operating instructions

This manual is also suitable for

R8-22
R8-26

safe smart strong

ED-PN-RX109-EN-v03

Language: English (original)

ENDUSER

INSTRUCTIONS

Receivers: R8-20, R8-22,

R8-26

©Tele-Radio i Lysekil AB

Datavägen 21

SE-436 32 Askim

Sweden

Phone: +46 (0)31 748 54 60

Enduser instructions│R8│

CONTENTS

CHAPTER 1: INTRODUCTION 4

1.1About this document 6

1.2About R8 receivers – R8-20, R8-22,R8-26 – 7

CHAPTER 2: SAFETY 8

2.1Warnings & restrictions 8

CHAPTER 3: TECHNICAL DATA 11

3.1Receiver specifications 11

3.2Current consumption 12

CHAPTER 4: PRODUCT GENERAL DESCRIPTION 13

4.1Receiver description 13

4.2Mechanical installation 14

CHAPTER 5: OPERATION 15

CHAPTER 6: WARRANTY, SERVICE, REPAIRS, AND MAINTENANCE 16

CHAPTER 7: REGULATORY INFORMATION 17

7.1Europe 17

ANNEX A: INDEX 18

ED-PN-RX109-EN-v03 3

Enduser instructions│R8│Chapter 1: Introduction

CHAPTER 1: INTRODUCTION

Thank you for using a Tele Radio product

READ ALL INSTRUCTIONS AND WARNINGS CAREFULLY BEFORE OPERATING

THE PRODUCTS.

These End user instructions have been published by Tele Radio and are not subject

to any guarantees. The End user instructions may be withdrawn or revised by Tele

Radio at any time and without further notice. Corrections and updates will be

added to the latest version of the manual. Always download the End user

instructions from our website, www.tele-radio.com, for the latest available version.

Keep the safety instructions for future reference.

IMPORTANT! These instructions are intended for end users. The instructions can be

printed and handed to end user.

Tele Radio remote controls are often built into wider applications. This

documentation is not intended to replace the determination of suitability or

reliability of the product for specific user applications and should not be used for

this purpose. It is the responsibility of any such users or integrators to perform the

appropriate and complete risk analysis, evaluation and testing of the products with

respect to the relevant specific application or use. Tele Radio shall not be

responsible or liable for misuse of the information contained herein.

Always refer to the applicable local regulations for installation and safety

requirements relating to cranes, hoists, material handling applications, lifting

equipment, industrial machinery, and/or mobile hydraulic applications using Tele

Radio products, e.g.:

lapplicable local and industrial standards and requirements,

lapplicable occupational health and safety regulations,

lapplicable safety rules and procedures for the factory where the equipment

is being used,

luser and safety manuals or instructions of the manufacturer of the

equipment where Tele Radio remote control systems are installed.

Tele Radio End user instructions do not include or address the specific instructions

and safety warnings of the end product manufacturer.

4 ED-PN-RX109-EN-v03

Enduser instructions│R8│Chapter 1: Introduction

Tele Radio products are covered by a warranty against material, construction, or

manufacturing faults. See "Chapter 6: Warranty, service, repairs, and maintenance".

ED-PN-RX109-EN-v03 5

Enduser instructions│R8│Chapter 1: Introduction

1.1About this document

Before installing or operating the product, read the corresponding documentation

carefully.

Tele Radio's product range is composed of transmitters, receivers, and accessories

intended for use together as a system.

These End user instructions cover general safety issues, main technical

specifications, and standard operating instructions. Images shown in this document

are for illustrative purposes only.

Please report any error or omission in this document, as well as any improvement

or amendment suggestion to td@tele-radio.com.

1.1.1TERM AND SYMBOL DEFINITIONS

The capitalized terms and symbol used herein shall have the following meaning:

lWARNING: indicates a hazardous situation which, if not avoided, could result

in death or serious injury.

lCAUTION: indicates a hazardous situation which, if not avoided, will result in

minor or moderate injury.

lIMPORTANT: is used for information that requires special consideration.

lNOTE: is used to address practices not related to physical injury.

This symbol is used to call attention to safety messages that would be

assigned the signal words "WARNING"or "CAUTION".

6 ED-PN-RX109-EN-v03

Enduser instructions│R8│Chapter 1: Introduction

1.2About R8 receivers – R8-20, R8-22,R8-26 –

R8 receivers have simplex communication and work in either discontinuous or

continuous mode.

There are three models.

Base board Expansion board Antenna

12–24V DC

1 relay

Analog IOs Internal External

R8-20 ● ●

R8-22 ● ● ●

R8-26 ● ● ●

●Standard

NOTE: R8-2* receivers are custom devices. Contact your representative for

assistance.

R8-2* receivers can control two DC motors via PWM outputs and have a built-in

feature for current output limitation (Max Current Cut Off).

R8-2* receivers can only be programmed via Tele Radio's proprietary programming

language.

On this receiver, supply voltage is also used as output voltage (if the receiver is

supplied with 12 VDC, so will the output).

1.2.1PWM OUTPUTS

PWM outputs are used for controlling the valves and DC motors (e.g to control the

speed or flow of the fluid).

1.2.2MAX CURRENT CUT OFF

This feature gives the possibility to limit the current output in ampere.

Ex: R8-20 is controlling a DC motor and the DC motor is stuck. the current of the DC

motor will increase. Adjusting the max. current cut off for DC motor via LML will

allow the receiver to cut the output when the max. current limit is reached and

protect both the DC motor and the receiver from damage.

ED-PN-RX109-EN-v03 7

Enduser instructions│R8│Chapter 2: Safety

CHAPTER 2: SAFETY

2.1Warnings & restrictions

Carefully read through the following safety instructions before

proceeding with the installation, configuration, operation, or

maintenance of the product. Failure to follow these warnings could

result in death or serious injury.

This product must not be operated without having read and understood the

Enduser instructions, the specific technical documentation (for customized

systems), and having received the appropriate training. The purchaser of this

product has been instructed how to handle the system safely. The following

information is intended for use as a complement to applicable local regulations

and standards.

IMPORTANT! Tele Radio remote controls are often built into wider applications.

These systems should be equipped with:

• a wired emergency stop where necessary

• a brake

• an audible or visual warning signal

2.1.1OPERATION

This radio system must not be used in areas where there is a risk of

explosion.

This equipment is not suitable for use in locations where children are

likely to be present.

Only qualified personnel should be permitted to access the transmitter

and operate the equipment.

The user should:

8 ED-PN-RX109-EN-v03

Enduser instructions│R8│Chapter 2: Safety

lAlways follow operating and maintenance instructions as well as all

applicable safety procedures and requirements.

lDo not open the receiver encapsulation unless you are qualified.

lYou must satisfy the age requirements in your country for operating

the equipment.

lIt is strictly prohibited to operate the equipment under the influence

of drugs, alcohol and/or medications.

lAlways test the transmitter stop button before operating it. Press

the stop button then twist and pull it out. This test should be done

on each shift, without a load.

lNever use a transmitter if the stop button is mechanically

damaged.Contact your supervisor or representative for service

immediately.

lNever leave the transmitter unattended.

lAlways switch the transmitter off when not in use. Store in a safe

place.

lKeep a clear view of the work area at all times.

2.1.2MAINTENANCE

Before maintenance intervention on any remote controlled equipments:

• always remove all electrical power from the equipment.

• always follow lockout procedures.

lKeep the safety information for future reference. Always download the

Enduser instructions from our website, www.tele-radio.com, for the latest

available version.

lIf error messages are shown, it is very important to find out what caused

them. Contact your representative for help.

lThe functionality of the stop button should be tested at least after every 200

hours’ use.

lIf the stop button is mechanically damaged, do not use the transmitter.

Contact your supervisor or representative for service immediately.

lDo not try to open the encapsulation.

lAlways contact your representative for service and maintenance work on the

product.

ED-PN-RX109-EN-v03 9

Enduser instructions│R8│Chapter 2: Safety

lKeep contacts and antennas clean.

lWipe off dust using a clean, slightly damp cloth.

lNever use cleaning solutions.

lCheck the encapsulation, foils and cable for damages every day. If you use

the product although the encapsulation or foil is damaged, moisture can

cause serious damage to the electronics.

10 ED-PN-RX109-EN-v03

Enduser instructions│R8│Chapter 3: Technical data

CHAPTER 3: TECHNICAL DATA

3.1Receiver specifications

R8-20, R8-22, R8-26

Power supply 12–24V DC, max. 10 A per H-bridge

Number of relays 1 (potential free*, 10A, 250V AC or 30 V

DC)1

Relay functionality Momentary, latching, interlocking

(programmable)

Number of digital inputs 8

Number of motor outputs 2**, 10A continuous load and 15A

transient (at 25°C) per motor output).

Radio frequency band 2405–2480 MHz

Frequency management Direct Sequence Spread Spectrum (DSSS)

Number of channels 16 (channel 11–26)

Channel separation 5 MHz

Radio communication Simplex

Max. number of registered transmitters 8

Antenna Internal antenna

Operating temperature -20 – +55 °C / -4 – +130 °F

IP code IP66

Dimensions (LxWxH) 120 x 117 x 51 mm / 4.7 x 4.6 x 2 in

Weight 420 g / 0.926 lbs

* Potential free means that a supply voltage is needed to get voltage out of a relay.

**Each motor output can be configured to 4 individual transistor outputs. For

customization, please contact your representative.

1Maximum load is indicated for resistive load only.

ED-PN-RX109-EN-v03 11

Enduser instructions│R8│Chapter 3: Technical data

3.2Current consumption

Input power Min.* Typical**

12V DC 1mA 50mA

24V DC 1mA 35mA

*Minimum current consumption = Receiver on, no radio communication established,

sleep mode activated.

**Typical current consumption = Receiver on, no radio communication established,

sleep mode deactivated.

12 ED-PN-RX109-EN-v03

Enduser instructions│R8│Chapter 4: Product general description

CHAPTER 4: PRODUCT GENERAL DESCRIPTION

The pictures shown in this chapter are for illustrative purposes only.

4.1Receiver description

1. Cable glands (M20x1.5)

ED-PN-RX109-EN-v03 13

Enduser instructions│R8│Chapter 4: Product general description

4.2Mechanical installation

NOTE: For mounting on a wall or equipment, use 4 M5x30mm screws or equivalent

fastening method.

14 ED-PN-RX109-EN-v03

Enduser instructions│R8│Chapter 5: Operation

CHAPTER 5: OPERATION

The receiver is always delivered with customized functionality and has no analog

output functions by default. Contact your representative for more information.

ED-PN-RX109-EN-v03 15

Enduser instructions│R8│Chapter 6: Warranty, service, repairs, and

maintenance

CHAPTER 6: WARRANTY, SERVICE, REPAIRS, AND

MAINTENANCE

Tele Radio products are covered by a warranty against material, construction and

manufacturing faults. During the warranty period, Tele Radio may replace the

product or faulty parts. Work under warranty must be performed by Tele Radio or

by an authorized service center specified by Tele Radio.

The following are not covered by the warranty:

lFaults resulting from normal wear and tear

lParts of a consumable nature

lProducts that have been subject to unauthorized modifications

lFaults resulting from incorrect installation and use

lDamp and water damage

Maintenance

lRepairs and maintenance must be performed by qualified personnel

lOnly use spare parts from Tele Radio

lContact your representative for service or any other assistance

lKeep the product in a clean, dry place

lKeep contacts and antennas clean

lWipe off dust using a slightly damp, clean cloth

NOTE: Never use cleaning solutions or high-pressure washer.

16 ED-PN-RX109-EN-v03

Enduser instructions│R8│Chapter 7: Regulatory information

CHAPTER 7: REGULATORY INFORMATION

NOTE: Models including additional naming conventions:

Model Article names Additional naming conventions

R8 R8-20

R8-22

R8-26

R00008-20, PN-R8-20

R00008-22, PN-R8-22

R00008-26, PN-R8-26

7.1Europe

Applies to: R8-20, R8-22, R8-26

7.1.1CE MARKING

Hereby, Tele-Radio i Lysekil AB, declares that the product(s) listed above

is/are in compliance with the Radio Equipment Directive 2014/53/EU.

The latest version of the complete EU Declaration of Conformity is

available at the following website: www.tele-radio.com.

7.1.2WEEE DIRECTIVE

This symbol means that inoperative electrical and electronic products

must not be mixed with household waste.The European Union has

implemented a collection and recycling system for which producers are

responsible. For proper treatment, recovery and recycling, please take

this product to a designated collection point.

Tele Radio strives to minimize the use of hazardous materials, promotes reuse and

recycling, and reduces emissions to air, soil and water. When a commercially viable

alternative is available, Tele Radio strives to restrict or eliminate substances and

materials that pose an environmental, health or safety risk.

ED-PN-RX109-EN-v03 17

Enduser instructions│R8│Annex A: Index

ANNEX A: INDEX

About R15 receivers 7

CE marking 17

Current consumption 12

Dimensions 11

IP code 11

Maintenance 16

Mounting dimensions

Receiver 14

Number of channels 11

Operating temperature 11

Power supply 11

Radio communication 11

Radio frequency band 11

Specifications 11

18 ED-PN-RX109-EN-v03

Enduser instructions│R8│Annex A: Index

Warnings & restrictions 8

Maintenance 9

Operation 8

WEEE directive 17

Weight 11

ED-PN-RX109-EN-v03 19

safe smart strong

These Enduser instructions are subject to change without prior notice.

Download the latest Enduser instructions from www.tele-radio.com .

Tele Radio R8-20 Operating instructions

Brand: Tele Radio

Model: R8-20

Type: Operating instructions

This manual is also suitable for

R8-22
R8-26

Download PDF

report

Tele Radio R8-20 Operating instructions

This manual is also suitable for

Tele Radio R8-20 Operating instructions

Related papers

Other documents