AETEK TE22-110-TX Quick Installation Manual

Brand
AETEK
Model
TE22-110-TX
Category
Security camera accessories
Type
Quick Installation Manual

This manual is also suitable for

1. Use CAT5e or CAT6 UTP/STP cables.
2. Please avoid using low quality cables, which will seriously limit the cabling distance and power delivery.
3. Make sure the power source is sufcient for your conguration.
TE10-110-RX / TE11-110-RX / TE10-110-TX / TE12-120-TX /
TE22-110-TX / TE22-120-TX EPoT Adapter
Model Power Source Description
TE10-110-RX 56VDC/65W EPoT DC in Rx Adapter, 1x EPoT RJ45, 1x FE RJ45, 1 DC Jack, -20ºC~60ºC
TE11-110-RX PoE Input EPoT PoE in Rx Adapter, 1x EPoT RJ45, 1x FE RJ45, -20ºC~60ºC
TE10-110-TX EPoT Tx Adapter, 1x EPoT RJ45, 1x FE RJ45, 1 DC Jack, -20ºC~60ºC
TE12-120-TX EPoT Tx Adapter, 2x EPoT RJ45, 1x FE RJ45, 1 DC Jack, -20ºC~60ºC
TE22-110-TX EPoT Outdoor Tx Adapter, 1x EPoT RJ45, 1x FE RJ45, -30ºC~60ºC
TE22-120-TX EPoT Outdoor Tx Adapter, 2x EPoT RJ45, 1x FE RJ45, -30ºC~60ºC
IMPORTANT:
INTRODUCTION
CONNECTION
PACKAGE CONTENTS
Quick Installation Guide
* 1x Quick Installation Guide * 1x 56VDC/65W Power Adapter (TE10-021-RX only)
* Waterproof Connect (TE22-110-TX / TE22-120-TX only)
EPoT Link
Connect to
EPoT TX
EPoT Link
Connect to
EPoT RX
Connect to
Switch
Connect 56V/65W
PowerAdapter
Connect to
PoE IP Camera
Connect 56V/65W
Power Adapter(Option)
PoE On/Off Switch
LINK
PWR
LAN
PoE
JOIN
OFF / ON
PoE
Outdoor 1-Port EPoT TX
4-Pair
LINK
1-4 Pin V-
5-8 Pin V+
++++
----
LAN
EPoT Link
Connect to EPoT RX
Connect to
PoE IP Camera
TE10-110-RX
TE10-110-TX
TE22-110-TX
EPoT Cat.5e/6 LINK pin assignment
5-8 Pin V+
++++
----
1-4 Pin V-
PWR
LINK
LAN PoE
JOIN
1-Port PoE PD EPoT Rx
EPoT
LINK
1-4 Pin V-
5-8 Pin V+
++++
----
4-Pair
LINK
4-Pair
LINK
EPoT Link
Connect to
EPoT TX
TE11-110-RX
Connect to
PoE Switch
LINK
PWR
LAN
1 2
PoE
2-Port EPoT TX
1 2
1
2
56VDC
EPoT
LINK
1-4 Pin V-
5-8 Pin V+
++++
----
OFF
ON
1
JOIN
PoE
2
LINK
PWR
LAN
1
JOIN
ON
OFF
PoE
2
PoE
Outdoor 2-Port EPoT TX
EPoT
LINK
1-4 Pin V-
5-8 Pin V+
----
12
1
2
2 1
EPoT Link
Connect to
EPoT RX
TE12-120-TX
Connect to
PoE IP Camera
Connect to
PoE IP Camera
EPoT Link
Connect to EPoT RX
Connect to
PoE IP Camera
Connect to
PoE IP Camera
PoE On/Off Switch
TE22-120-TX
Connect 56V/65W
Power Adapter(Option)
Ethernet (Data)
Power
TE10-110-RX
Network Switch
TE10-110-TX
Cat5e/6 cable
TX
TE22-110-TX
Cat5e/6 cable
Application :
TE11-110-RX
4-Pair
LINK
4-Pair
LINK
H30-044-90
NDR-240-48
240W Power Supply
UPoE Swich
Cat.5e/6 PoE (Data + Power)
PWR
LINK
LAN PoE
JOIN
1-Port PoE PD EPoT Rx
EPoT
LINK
1-4 Pin V-
5-8 Pin V+
++++
----
TE10-110-RX
Network Switch
TE12-120-TX
Cat5e/6 cable
TE22-120-TX
Cat5e/6 cable
TE11-110-RX
4-Pair
LINK
H30-044-90
NDR-240-48
240W Power Supply
UPoE Swich
PWR
LINK
LAN PoE
JOIN
1-Port PoE PD EPoT Rx
EPoT
LINK
1-4 Pin V-
5-8 Pin V+
++++
----
LINK
PWR
LAN
1 2
PoE
2-Port EPoT TX
1 2
1
2
56VDC
EPoT
LINK
1-4 Pin V-
5-8 Pin V+
++++
----
OFF
ON
1
JOIN
PoE
2
INSTALLATION
NOTE:
The TE22-110-TX Outdoor EPoC Adapter must be
grounded using a ground wire between the
ground
screw and earth ground.
IMPORTANT:
Ground screw
* Make sure the grouning
resistance is lower than
0.5Ω.
TE22-110-TX
LINK
PWR
LAN
PoE
JOIN
OFF / ON
PoE
Outdoor 1-Port EPoT TX
4-Pair
LINK
1-4 Pin V-
5-8 Pin V+
++++
----
LAN
TE22-120-TX
LINK
PWR
LAN
1
JOIN
ON
OFF
PoE
2
PoE
Outdoor 2-Port EPoT TX
EPoT
LINK
1-4 Pin V-
5-8 Pin V+
----
12
1
2
2 1
LEDs
PoE Yellow ON PoE: Power port is connected to PD
LAN Green ash LAN: Data is being transmitted or received.
OFF No connection
PWR Yellow ON Power adapter is connected the EPoT adapter
LINK Green ON Rx and Tx EPoT adapter is connected.
DIP Switch
DIP# On Delivery PoE output to PD device
Off No PoE output to PD device
NOTE:The PoE On/Off switch is only available on TE10-110-TX / TE12-120-TX
/ TE22-110-TX
/
TE22-120-TX
Distance/Power Chart
NOTE:
1. The number comply using 4 pair Cat6 cables.
2. The length of network cable for camera connection is 1m Cat6 cable.
3. The power delivery will vary on the quality of Cat6 cable due to
resistance.
AETEK INC.
3F, No.192, Lien-Cheng Rd., Chung-Ho, New Taipei City, 235, Taiwan, R.O.C.
|T: +886-2-82452822| W: www.aetektec.com| E: [email protected]
All specications are subject to change without noice.
Copyright © 2018 AETEK INC. All rights reserved.
To disconnect a LAN cable, loosen the cable
gland and pull the cable against the socket
wall towards the side of the locking tab.
Outdoor LAN Port
IMPORTANT -
please follow the procedures below carefully to ensure the best seal:
1. Fit a RJ45 plug to the Cat5e/6 cable
2. Thread the Cat5e/6 cable through the cap(A) & grip(B)
3. Split rubber(C), rubber have two sizes for meet 4.5~6.5mm Cat5e/6 cable.
4. Fit the split rubber(C) over the Cat5e/6 cable
5. Thread the Cat5e/6 cable through the body(D)
6. Fit the washer(E) to the TE22-110-TX/TE22-120-TX connector
7. Plug the RJ45 connector on the Cat5e/6 cable into the TE22-110-TX/
TE22-120-TX
8. Hold TE22-110-TX/TE22-120-TX and then screw the body(D) onto the
TE22-110-TX/TE22-120-TX connector tighten rmly
9. Push rubber(C) in the grip(B) and screw the cap tighten firmly. The
Cat5e/6 cable is sealed when the rubber(C) & grip(B) bulges to the edge
of the cap(A).
Outdoor 4 Pair LINK Port Connector Assembly
Washer (E)
Body (D)
Rubber (C) Grip (B)
Cap (A)
Rubber (C) Rubber (C)
Split
Length of Coaxial Cable
300m 34.72W
500m 25.2W
800m 13.11W
1000m 10W
1200m 9.66W
1200m ~ 2400m Data only (100Mbps)
  • Page 1 1
  • Page 2 2

AETEK TE22-110-TX Quick Installation Manual

Brand
AETEK
Model
TE22-110-TX
Category
Security camera accessories
Type
Quick Installation Manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents