Diamond Systems Rhodeus User manual

GF

Rhodeus

Low P

ower AMD Geode™ LX800 PC/104 CPU Module with CRT/LCD, LAN and CF

User’s Manual

Copyright  2008

Diamond Systems Corporation

1255 Terra Bella Ave.

Mountain View, CA 94043

Tel (650) 810-2500

www.diamondsystems.com

- i -

Index

Table of Contents

Chapter 1 - Introduction....................................................1

1.1 Copyright Notice.............................................................2

1.2 About User’s Manual .....................................................2

1.3 Warning.............................................................................2

1.4 Replacing the lithium battery ......................................3

1.5 Technical Support ..........................................................3

1.6 Warranty............................................................................4

1.7 Packing List .....................................................................5

1.8 Ordering Information .....................................................5

6SHFL¿FDWLRQ....................................................................6

1.10 Board Dimensions........................................................7

Chapter 2 - Installation ......................................................9

2.1 Block Diagrams............................................................ 10

2.2 Jumpers and Connectors ...........................................11

KBM1: Keyboard & Mouse Connector ..................13

LAN1: Fast Ethernet Connector.............................13

IDE1: 44 pin IDE Connector....................................14

PWR1: Power Supply Connector...........................14

PC/104: PC/104 ISA Interface .................................15

JRS1: COM 2 RS-232/422/485 Select.....................16

LLED1: LAN LED Indicators...................................16

JFRT1: Switches and Indicators............................16

IR1: Intrared Connector ..........................................17

VGA1: CRT Connector............................................17

USB1: USB Connector............................................17

FDD1: 20 pins FDD Connector...............................18

JBAT1: CMOS Setup ...............................................18

LPT1: 20 pins Parallel Port Connector..................19

CON1: RS-422/ 485 Output Connector ..................19

LCD1: TTL LCD Connector.....................................20

- ii -

Index

COM1/ COM2: Serial Port Connector

....................

20

CFD1: CompactFlash II Socket

..............................21

2.3 The Installation Paths of CD Driver......................... 22

Chapter 3 - BIOS ................................................................23

3.1 BIOS Introduction........................................................ 24

3.2 BIOS Setup.................................................................... 24

3.3 Standard CMOS Features .......................................... 25

3.4 Advanced BIOS Features........................................... 28

3.5 Advanced Chipset Features...................................... 30

3.6 Integrated Peripherals................................................ 32

3133&,&RQ¿JXUDWLRQV............................................. 39

3.8 PC Health Status.......................................................... 41

3.9 Load Optimized Defaults .......................................... 42

3.10 Set Password ............................................................ 43

3.11 Save & Exit Setup ...................................................... 44

3.12 Exit Without Saving .................................................. 45

3.13 BIOS Beep Sound code list..................................... 46

3.14 BIOS memory mapping............................................ 46

3.15 Award BIOS POST Codes........................................ 47

Chapter 4 - Appendix .......................................................51

4.1 I/O Port Address Map.................................................. 52

4.2 Interrupt Request Lines (IRQ)................................... 53

4.3 DMA Map........................................................................ 53

4.4 Memory Address Map................................................. 54

4.5 LCD Data Cable Pin Assignment Example........... 55

- 1 -

Introduction

1Chapter 1

Introduction

Chapter 1 - Introduction

- 2 -

Introduction

1.1 Copyright Notice

The information in this document is subject to change without prior notice in

order to improve the reliability, design and function. It does not represent a

commitment on the part of the manufacturer.

Under no circumstances will the manufacturer be liable for any direct,

indirect, special, incidental, or consequential damages arising from the

use or inability to use the product or documentation, even if advised of the

possibility of such damages.

This document contains proprietary information protected by copyright.

All rights are reserved. No part of this manual may be reproduced by any

mechanical, electronic, or other means in any form without prior written

permission of the manufacturer.

1.2 About User’s Manual

This User’s Manual is intended for experienced users and integrators with

hardware knowledge of personal computers. If you are not sure about any

description in this User’s Manual, please consult your vendor before further

handling.

1.3 Warning

Single Board Computers and their components contain very delicate

Integrated Circuits (IC). To protect the Single Board Computer and its

components against damage from static electricity, you should always follow

the following precautions when handling it :

1. Disconnect your Single Board Computer from the power source when you

want to work on the inside.

2. Hold the board by the edges and try not to touch the IC chips, leads or

circuitry.

3. Use a grounded wrist strap when handling computer components.

4. Place components on a grounded antistatic pad or on the bag that came

with the Single Board Computer, whenever components are separated

from the system.

- 3 -

Introduction

1.4 Replacing the lithium battery

Incorrect replacement of the lithium battery may lead to a risk of explosion.

The lithium battery must be replaced with an identical battery or a battery

type recommended by the manufacturer

.

Do not throw lithium batteries

into the trashcan. It must be disposed of in

accordance with local regulations concerning special waste.

1.5 T

echnical Support

Please do not hesitate to e-mail our

support team when you need assistance

www.diamondsystems.com

[email protected]

- 4 -

Introduction

1.6 Warranty

This product is warranted to be in good working order for a period of two

years from the date of purchase. Should this product fail to be in good

working order at any time during this period, we will, at our option, replace

or repair it at no additional charge except as set forth in the following terms.

7KLVZDUUDQW\GRHVQRWDSSO\WRSURGXFWVGDPDJHGE\PLVXVHPRGL¿FDWLRQV

accident or disaster.

9HQGRUDVVXPHVQROLDELOLW\IRUDQ\GDPDJHVORVWSUR¿WVORVWVDYLQJVRUDQ\

other incidental or consequential damage resulting from the use, misuse of,

or inability to use this product. Vendor will not be liable for any claim made

by any other related party.

Vendors disclaim all other warranties, either expressed or implied, including

EXWQRWOLPLWHGWRLPSOLHGZDUUDQWLHVRIPHUFKDQWLELOLW\DQG¿WQHVVIRU

a particular purpose, with respect to the hardware, the accompanying

product’s manual(s) and written materials, and any accompanying hardware.

7KLVOLPLWHGZDUUDQW\JLYHV\RXVSHFL¿FOHJDOULJKWV

Return authorization must be obtained from the vendor before returned

merchandise will be accepted. Authorization can be obtained by calling or

faxing the vendor and requesting a Return Merchandise Authorization (RMA)

number. Returned goods should always be accompanied by a clear problem

description.

-

5

-

Introduct

i

on

1.7 Packing List

If any of the above

i

tems

i

s damaged or m

i

ss

i

ng, contact your vendor

i

mmed

i

ately.

1.8 Ordering Information

Rhodeus

PC/104 CPU module w

i

th AMD Geode™ LX800

(

5

00MHz), 1 x SO-DIMM, CRT/LCD & LAN

Cable K

i

t

(Opt

i

onal)

1 x USB Cable

2

x COM Port Cable

1 x FDD Flat Cable

1 x IDE Cable

1 x Parallel Port Cable

1 x LAN Cable

1 x VGA Cable

1 x KB/MS Cable

1 x Rhodeus Single Board Computer

1 x CD-ROM

1 x Qu

i

ck Installat

i

on Gu

i

de

- 6 -

Introduction

6SHFL¿FDWLRQ

Form Factor PC/104 CPU module

Processor AMD Geode™ LX800

Cache 64K L1 cache and 128K L2 cache

Chipset AMD LX800 + CS5536

System Memory 1 x 200 pins DDR SO-DIMM up to 1GB SDRAM

VGA/ LCD Controller

AMD Geode LX series CPU integrated VGA

controller with 2D Engine (Shared memory Max.

64MB)

Ethernet Realtek 8100CL 10/100 base-T Ethernet

LCD Supports 18/24-bit TTL up to 1280 x 1024

I/O Chips W83627HG

BIOS Phoenix-Award BIOS

IDE Interface 1 x Ultra DMA

33, support 2 IDE devices

Serial Port

2 x RS-232 ports

COM2: RS-232/RS-422/RS-485 selectable

Parallel Port / Floppy

1 x SPP/EPP/ECP mode

1 x Floppy connector

KBMS Standard PS/2 Keyboard and Mouse

Universal Serial Bus 2 x USB 2.0 ports

PCI to ISA bridge ITE8888G

Expansion Bus 1 x PC/104 interface

Flash Disk 1 x Type II Compact Flash Disk Socket up to 8GB

Hardware Monitor Integrated in W83627HG

RTC

AMD Geode CS5536 built-in RTC with lithium

battery

Power Input Connector 1*4 pins power connector

Operation Temp.

-20

oC to +70oC or -40oC to +85oC

Watchdog Timer 1 - 255 Level (Sec. or Min.)

Dimension (L x W) 96 x 90 mm (3.8” x 3.5”)

- 7 -

Introduction

1.10 Board Dimensions

Unit:mm

- 8 -

Introduction

Unit:mm

- 9 -

Installation

2Chapter 2

Installation

Chapter 2 - Installation

- 10 -

Installation

2.1 Block Diagrams

1 x 200pin

SO-DIMM Socket

PCI LAN

Controller

LAN

RJ-45

Analog

R.G.B.

TTL 18/24 bit

VGA

LCD

AMD Geode

LX800 CPU

500MHz

Memory Bus

USB I/F

IDE ATA I/F

1 x IDE

4 x USB

COM1

COM2

LPT1

FDD

IrDA

KB

MS

1 x CF

CS5536

AMD Geode

Super IO

Controller

PC/104

PCI to ISA

Bridge

ISA Bus

LPC I/F

PCI Bus

- 11 -

Installation

2.2 Jumpers and Connectors

10

9

1

2

JBAT1

13

COM1

17

KBM1

1

LAN1

2

IDE1

3

COM2

18

LCD1

16

LPT1

14

FDD1

12

USB1

11

VGA1

10

IR1

9

PWR1

4

JFRT1

8

LLED1

7

JRS1

6

PC/104

5

CON1

15

10

9

1

2

44

43

9

1

2

1

4

1

2

6

5

1

2

C19

B32

A32

D19

1

16

15

1

2

C0

A1

B1

D0

9

1

2

20

19

1

2

20

19

1

2

40

39

1

2

- 12 -

Installation

Label Function

JRS1 COM2 RS-232/422/485 Select

JBAT1 CMOS Jumper Settings

Jumper / Connector Quick Reference

Jumpers

DIMM1 200 pins DDR SDRAM DIMM Socket

PC104_1 PC/104 for ISA Interface

KBM1 PS/2 Keyboard and Mouse

VGA1 CRT Display

LCD1 TTL LCD Panel Connector

COM1 ~ COM2 Serial Ports

CON1 RS-422/485 Output

IR1 Infrared (IR) Connector

LPT1 Parallel Port

LAN1 LAN Ethernet Connector

LLED1 LAN LED Connector

USB1 USB 1/2 Connector

PWR1 Power Connector Small 4P

JFRT1 Front Panel (Switches and Indicators)

FDD1 Floppy Disk Drive Connector

IDE1 Primary IDE Connector

CFD1 Compact Flash Socket

Connectors

- 13 -

Installation

KBM1: Keyboard & Mouse Connector (1)

Connector type: 2.0mm pitch 1x6 pins wafer connector

Pin Description

1 KB_DATA

2 GND

3 MS_DATA

4 KB_CLK

5 KB_VCC

6 MS_CLK

1

LAN1: Fast Ethernet Connector (2)

Pin Description Pin Description

1 TX+ 2 TX-

3 RX+ 4 N/C

5 N/C 6 RX-

7 N/C 8 N/C

9 GND 10 N/C (Key)

10

9

1

2

Connector type: 2.0mm pitch 2x5 pin header

- 14 -

Installation

PWR1: Power Supply Connector (4)

Pin Description

1 +5V

2 GND

3 GND

4 +12V

1

IDE1: 44 pins IDE Connector (3)

Pin Description Pin Description

1 IDE RESET 2 GND

3 DATA7 4 DATA8

5 DATA6 6 DATA9

7 DATA5 8 DATA10

9 DATA4 10 DATA11

11 DATA3 12 DATA12

13 DATA2 14 DATA13

15 DATA1 16 DATA14

17 DATA0 18 DATA15

19 GND 20 N/C (Key)

21 REQ 22 GND

23 IO WRITE 24 GND

25 IO READ 26 GND

27 IO READY 28 IDESEL

29 DACK 30 GND

31 IRQ14 32 N/C

33 ADDR1 34 DIAG

35 ADDR0 36 ADDR2

37 CS#2 38 CS#3

39 IDEACTP 40 GND

41 +5V 42 +5V

43 GND 44 N/C

44

43

2

1

Connector type: 2.0mm pitch 2x22 pin header

Connector type: 2.54mm pitch 1x4 pins wafer one wall connector

- 15 -

Installation

PC/104: PC/104 ISA Interface (5)

A1

B1

A32

B32

D19

C19

D0

C0

Pin Description Pin Description Pin Description Pin Description

D0 GND C0 GND A1 IOCHCK# B1 GND

D1 MEMCS16# C1 SBHE# A2 SD7 B2 RST_DRV

D2 IOCS16# C2 LA23 A3 SD6 B3 +5V

D3 IRQ10 C3 LA22 A4 SD5 B4 IRQ9

D4 IRQ11 C4 LA21 A5 SD4 B5 N/C

D5 IRQ12 C5 LA20 A6 SD3 B6 DREQ2

D6 IRQ15 C6 SA19 A7 SD2 B7 N/C

D7 IRQ14 C7 SA18 A8 SD1 B8 0WS#

D8 DACK0# C8 SA17 A9 SD0 B9 +12V

D9 DREQ0 C9 MEMR# A10 IOCHRDY B10 GND

D10 DACK5# C10 MEMW# A11 AEN B11 SMEMW#

D11 DREQ5 C11 SD8 A12 SA19 B12 SMEMR#

D12 DACK6# C12 SD9 A13 SA18 B13 IOW#

D13 DREQ6 C13 SD10 A14 SA17 B14 IOR#

D14 DACK7# C14 SD11 A15 SA16 B15 DACK3#

D15 DREQ7 C15 SD12 A16 SA15 B16 DREQ3

D16 +5V C16 SD13 A17 SA14 B17 DACK1#

D17 MASTER# C17 SD14 A18 SA13 B18 DREQ1

D18 GND C18 SD15 A19 SA12 B19 REFRESH#

D19 GND C19 GND A20 SA11 B20 SYSCLK

A21 SA10 B21 IRQ7

A22 SA9 B22 IRQ6

A23 SA8 B23 IRQ5

A24 SA7 B24 IRQ4

A25 SA6 B25 IRQ3

A26 SA5 B26 DACK2#

A27 SA4 B27 TC

A28 SA3 B28 BALE

A29 SA2 B29 +5V

A30 SA1 B30 ISA_CLK

A31 SA0 B31 GND

A32 GND B32 GND

Connector type: PC104 PRESS FIT 2x20P connector

- 16 -

Installation

JFRT1: Switches and Indicators (8)

It provides connectors for system indicators that provides light indication of

the computer activities and switches to change the computer status.

Connector type: 2.54mm pitch 1x8 pin header.

Pin Description

1 RESET+

2 RESET-

3 PWRLED+

4 PWRLED-

5 HDD LED+

6 HDD LED-

7 SPK OUT+

8 SPK OUT-

1

,WFDQEHFRQ¿JXUHG&20WRRSHUDWHLQ5656RU56PRGH

Connector type: 2.00mm pitch 2x3 pin header.

Select 1-2 3-4 5-6

RS-232 (Default) ON OFF OFF

RS-422 OFF ON OFF

RS-485 OFF OFF ON

JRS1: COM 2 RS-232/422/485 Select (6)

6

5

2

1

6

5

2

1

6

5

2

1

LLED1: LAN LED indicators (7)

Pin Description

1 LAN1_ACTIVE-

2 LAN1_ACTIVE+

3 LAN1_LINK-

4 LAN1_LINK+

1

Connector type: 2.54mm pitch 1x4 pin header.

- 17 -

Installation

USB1 supports two USB 2.0 w/ 480MB/s by pin header

Pin Description Pin Description

1 +5V 2 +5V

3 USBD- 4 USBD-

5 USBD+ 6 USBD+

7 GND 8 GND

9 GND 10 N/C (Key)

USB1: USB Connector (11)

10

9

1

2

VGA1: CRT Connector (10)

Pin Description Pin Description

1 RED 2 GREEN

3 BLUE 4 N/C

5 GND 6 GND

7 GND 8 GND

9 N/C 10 GND

11 N/C (Key) 12 VDDAT

13 HSYNC 14 VSYNC

15 VDCLK 16 N/C

16

15

1

2

IR1: Infrared Connector (9)

Connector Type: 2.54mm pitch 5 pins header

Pin Voltage

1 +5V

2 N/C

3 IRRX

4 GND

5 IRTX

1

Connector type: 2.0mm pitch 2x5 pin header

Page is loading ...

Diamond Systems Rhodeus User manual

This manual is also suitable for

Diamond Systems Rhodeus User manual

Related papers

Other documents