Anova LBCBR Installation guide

Type
Installation guide

This manual is also suitable for

Anova LBCBR2 is a bike rack that can be installed on concrete footings or slabs. It is made of stainless steel and has a powder coating finish. The rack can accommodate up to 4 bikes and comes with all the necessary hardware for installation. The LBCBR2 is a sturdy and durable bike rack that is perfect for use in both residential and commercial applications.

Anova LBCBR2 is a bike rack that can be installed on concrete footings or slabs. It is made of stainless steel and has a powder coating finish. The rack can accommodate up to 4 bikes and comes with all the necessary hardware for installation. The LBCBR2 is a sturdy and durable bike rack that is perfect for use in both residential and commercial applications.

anovafurnishings.com
888.535.5005 tel
TOOLS NEEDED: HARDWARE NEEDED:
Installation Instructions
Step-by-Step Installation Sequence
!
Hammer DrillHammer
Pencil
9/16"Wrench
Wire Brush
Level
Safety Glasses
Beacon Hill Standard & Custom Bike Racks
(4) 3/8" x 5" 18-8
Stainless Steel Stud Anchors
92188A203
Optional: (4) 3/8"
Rubber Washers
90130A050
Masonry Drill Bit Set
3/16", and 3/8"
Product requires assembly before installation.
Examine the footing or slab for damage or defects. The footing or slab should be reinforced concrete rated at a
3,000 psi minimum and be cured for at least 28 days prior to the installation of the bike rack.
CAUTION: Oversized holes and holes drilled too deep in the concrete will make it dicult to set the anchor.
SECTION A-A
SCALE 1 / 20
A A
1
1
2
2
A A
B B
1
???
7-BIKE SURFACE RACK - POWDER
OF
LBR7PSURF
1
REV
SHEET
1:1
SCALE
DATE 4/18/2018
DWG NO
TITLE
A
DRAWN D. METZ
SIZE
ALL DIMENSIONS ARE IN INCHES AND ALL ANGLES
OR BENDS ARE 90
UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
PRINT IS FOR FABRICATION ONLY. ALL SURFACES
MAY EXPAND BY .125
.0625 DURING COATING.
TOLERANCES UNLESS NOTED:
X
1 X.X
.5 X.XX ± .25 X.XXX ± .125
X.XXXX ± .0625 X.XXXXX ± .03125
X.XXXXXX
.015625 ANGULAR ± 1°
211 North Lindbergh Blvd.
St. Louis, MO 63141
888.535.5005 tel
314.754.0835 fax
specify@anovafurnishings.com
anovafurnishings.com
THIS DRAWING AND ALL THE INFORMATION CONTAINED HEREIN IS THE PROPERTY OF
ANOVA. DO NOT USE OR COPY WITHOUT WRITTEN PERMISSION.
THIS DRAWING IS CONFIDENTIAL AND IS SUBJECT TO RETURN ON DEMAND.
THIRD ANGLE PROJECTION
REV DESCRIPTION DATE
A01 ADDED FOOT MOUNT AND
DIMENTIONS 08/30/18
NOTES:
THIS DRAWING IS FOR PROTOTYPE OR TOOLING
USE ONLY. DO NOT USE FOR PRODUCTION.
63.6250
2.3750 O.D.
5.0000Ø
9.8750
14.6250
36.0000
66.2500
3.4641
(6 PLCS)
3.0000
(4 PLCS)
1.7321
(4 PLCS)
57.2500
.4375
(6 PLCS)
1.73"
(4 PLCS)
3.00"
(4 PLCS)
3.46"
(6 PLCS)
29.5"
Ø .44"
(6 PLCS)
Manufactured in the U.S.
Note: Please contact Customer Care at 1-866-797-1761 when ordering replacement parts.
Installation Instructions
Step-by-Step Installation Sequence
1.
2.
3.
5.
4.
Evacuate debris from mounting holes using compressed air and a steel wire
brush. This will create a clean environment for the anchor system.
!
Locate an anchor and adjust the nut so it is ush with the top of the anchor to
protect the threads from being damaged. Insert the anchor into the hole.
Use the hammer to x the anchor into the drilled hole by giving it several
hammer blows.
6.
7.
8.
!
Repeat steps 2 - 5 until all anchors are installed.
24
5
10/04/2018 Copyright 2019 ANOV
Care should be given to avoid rubbing the powder coating o the foot.
A 3/8" rubber washer is a suitable replacement option. Mount the bike rack
to the ground by placing a washer and a nut onto each anchor. Leave the
hardware nger tight until all of them have been installed. Verify that the bike
rack is level before tightening the anchors. Tighten all of the hardware with a
9/16" wrench.
Remove the nuts and washers o of the anchors. Align the mounting holes of
the bike rack over top of the anchors and slide it down into place.
It is recommended that you start holes in sequential order from the
smaller to the larger drill bits to avoid oversized holes or holes drilled too
deep. Begin with 3/16" diameter drill bit followed by the 3/8" diameter bit.
Place bike rack in the desired location. Mark the location of the holes with a
pencil. To verify the alignment of the anchor markings you may reference the
bottom of page 1.
7
8.28.1
Beacon Hill Standard & Custom Bike Racks
  • Page 1 1
  • Page 2 2

Anova LBCBR Installation guide

Type
Installation guide
This manual is also suitable for

Anova LBCBR2 is a bike rack that can be installed on concrete footings or slabs. It is made of stainless steel and has a powder coating finish. The rack can accommodate up to 4 bikes and comes with all the necessary hardware for installation. The LBCBR2 is a sturdy and durable bike rack that is perfect for use in both residential and commercial applications.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI