Atlas Metal Industries WHGP-1, WHGP-2 Datasheet

  • Hello! I am an AI chatbot trained to assist you with the Atlas Metal Industries WHGP-1 Datasheet. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
a subsidiary of Mercury Aircraft
1135 NW 159 Dr., Miami, Florida 33169
Tel: (305) 625-2451 or (800) 762-7565 Fax: (305) 623-0475
DROP-IN SERVING EQUIPMENT
CARVING STATION
Item No.
Quantity
WHGP-1
WHGP-2
DESCRIPTION:
Sell the sizzle! Nothing increases impulse sales
more than a carving steamship round, roast
turkey or ham right in the serving line. With the
Set-N-Serve Carving Station, virtually any
counter can be converted to a carving station.
It’s fully assembled and pre-wired - just plug it
in and turn it on. Even a gravy pan is provided.
The unit is fully insulated and provided with a
factory applied gasket so that it can be installed
in the finest wood fixtures, without marring the
counter top. The WHGP-2 is furnished with a
3/4 dia. drain; each unit is furnished with au-jus
gravy pan, perforated stainless steel top plate
with meat prongs, and thermostat control.
FEATURES:
Fully insulated to retain heat - protects
fixtures and saves energy
Thermostatically controlled
Factory applied gasket - makes installation a
snap and seals units to the counter top, thus
eliminating seepage
Comes complete - au-jus pan and perforated
stainless top with meat prongs
SS-27
WHGP-1 SHOWN
a subsidiary of Mercury Aircraft
1135 NW 159 Dr., Miami, Florida 33169
Tel: (305) 625-2451 or (800) 762-7565 Fax: (305) 623-0475
SS-28
TOP: Constructed of 18 gauge, type 304 stainless
steel, die stamped with a raised perimeter bead.
There shall be a solid vinyl gasket under the beaded
edge to form a seal to the counter top, thus prevent-
ing seepage or marring of the counter top.
Embossed mounting lugs are provided along the
inner surface of the top to hold the removable adapter
bars in place. A full set of adapter bars is provided.
LINER: The inner liner shall be 18 gauge, type 304
stainless steel, one piece construction, all welded,
ground and polished to a uniform finish. All corners
are coved with a minimum 1/4" radius. A 3/4" dia.
drain with strainer, 4" PVC nipple, and valve is provid-
ed in WHGP-2 only.
INSULATION: The pan is fully insulated with high
density fiberglass insulation, 1" thick on all sides, 2"
thick on the bottom, and enclosed by a 22 gauge
galvanized steel outer liner. The entire unit is remov-
able without the use of tools.
PERFORATED ADAPTER: The liner is fitted with a
perforated adapter plate with four-prong meat holder
and ladle opening. Directly beneath the adapter plate
SPECIFICATIONS:
is a sloped gravy pan to hold the meat juices for bast-
ing or gravy. The adapter and pan are removable for
cleaning.
ELECTRICAL: All heating elements are pre-wired to a
single thermostat control with a pilot light. The unit is
supplied with a 6' long, 3-wire cord and plug on oper-
ators left. Available for single phase only.
Specifications subject to change without notice.
ACCESSORIES:
Apron mounted, remote controls
(CONTACT FACTORY for opening size)
Drain, with strainer, brass nipple and valve on
WHGP-1
CARVING STATION
MODEL “A”
PAN SIZE
W x L x D
CUT-OUT
REQUIRED
SHIP WT.
(lbs.)
WHGP-1 16 19-7/8” X 11-3/4” X 6 22-1/4” X 14-1/4” 30
WHGP-2 29-3/4” 19-7/8” X 25-1/2” X 6 22-1/4” X 28” 30
MODEL
ELECTRICAL
CHARACTERISTICS
NEMA
CONFIGURATION
WHGP-1 8.3 amps - 1.0 KW - 120V 5-15P
WHGP-2 14.2 amps - 1.7 KW - 120V 5-15P
01/08-SC
A
24”
9”
WH-2 Hot Unit
A
DGP-2 Gravy Pan
3 3/4”
7 1/4”4 1/8”
1
9 7/8”
4”
6”
3 3/4”
2 1/2”
3 3/4”
/