Movincool Office Pro 12 / Office Pro 18 / Office Pro 24 Owner's manual

SERVICE MANUAL

OFFICE PRO 60

SERIAL NUMBER FROM APRIL 2007 (0407) TO PRESENT

DocID: 00G00016E

whole or in part, without the written permission of the publisher. DENSO

SALES CALIFORNIA, INC. reserves the right to make changes without

prior notice. MovinCool is a registered trademark of DENSO

Corporation.

Table of Contents

Operation Section

1. PRECAUTIONS FOR SAFETY

1.1 Foreword. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.2 Definition of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.3 General Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2. GENERAL DESCRIPTION

2.1 Spot Cooler. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.2 Compact Design. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.3 Easy Transportation and Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.4 Energy Conservation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3. CONSTRUCTION

3.1 Exterior Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

3.2 Exterior Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3.3 Internal Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

3.4 Basic Construction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

3.5 Air Flow. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3.6 Compressor and Fans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3.7 Condensate Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3.8 Drain Tanks (optional). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

4. SPECIFICATIONS

4.1 Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4.2 Characteristics (at 230 V). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

4.3 Characteristics (at 208 V). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

5. REFRIGERANT SYSTEM

5.1 Refrigerant System Construction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

5.2 Compressor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

5.3 Condenser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

5.4 Capillary Tube. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

5.5 Evaporator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

5.6 High Pressure Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

6. ELECTRICAL SYSTEM

6.1 Circuit Diagram and Control Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

6.2 Basic Operation of The Office Pro 60 Electrical Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Table of Contents

6.3 Control Box. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

6.4 Fan Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

6.5 Compressor Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

6.6 Condensate Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

6.7 Drain Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

6.8 Automatic Restart after Power Interruption. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

6.9 Compressor Protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

6.10 Temperature Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

6.11 Fan Mode Control Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

6.12 Temperature Scale Display Switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

6.13 Warning Signal Connection (Output Signal Terminal L+ and L-) . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

6.14 Fire Alarm Control Panel Connection (Input Signal Terminal E+ and E-). . . . . . . . . . . . . . . . . . . . . 30

Table of Contents

Repair Section

7. TROUBLESHOOTING

7.1 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

7.2 Self-Diagnostic Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

7.3 Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

7.4 Basic Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

8. DISASSEMBLY

8.1 Parts Construction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

8.2 Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

8.3 Removal of Electrical Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

8.4 Removal of Blower Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

8.5 Removal of Condensate Pump. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

8.6 Inspection of Capacitor (for Fan Motor and Compressor) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

8.7 Inspection of Drain Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

8.8 Inspection of Fan Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

8.9 Inspection of Compressor Motor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

8.10 Inspection of Wiring Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

8.11 Inspection of Thermistor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

8.12 Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

9. REFRIGERANT SYSTEM REPAIR

9.1 Repair of Refrigerant System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

9.2 Removal of Refrigeration Cycle Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

9.3 Charging the System with R-410A Refrigerant. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

9.4 Refrigerant Charging Work. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

10. REASSEMBLY

10.1 Removal of Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

10.2 Compressor Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

10.3 Blower Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

10.4 Wiring Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

10.5 Perform the Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

10.6 Caster Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

10.7 Schematic. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Operation Section

6

1. PRECAUTIONS FOR SAFETY

1.1 Foreword

• This manual has been published to service the MovinCool Office Pro 60. Please use this service

manual only when servicing the Office Pro 60.

1.2 Definition of Terms

1.3 General Precautions

WARNING

• All electrical work if necessary, should only be performed by qualified electrical

personnel. Repair to electrical components by non-certified technicians may result in

personal injury and/or damage to the unit. All electrical components replaced must be

genuine MovinCool parts, purchased from an authorized reseller.

• When handling refrigerant, always wear proper eye protection and do not allow the

refrigerant to come in contact with your skin.

• Do not expose refrigerant to an open flame.

• The proper electrical outlet for MovinCool units must be equipped with a “UL” approved

ground-fault breaker to prevent electrical shock from the unit.

• When brazing any tubing, always wear eye protection, and work only in a well ventilated

area.

• Disconnect power before servicing unit.

• Be careful of any sharp edges when working on unit.

Describes precautions that should be observed in order to prevent injury to

the user during installation or unit operation.

Describes precautions that should be observed in order to prevent damage to

the unit or its components, which may occur during installation or unit

operation if sufficient care is not taken.

NOTE Provides additional information that facilitates installation or unit operation.

WARNING

CAUTION

Operation Section

7

2. GENERAL DESCRIPTION

2.1 Spot Cooler

• In general, conventional air conditioners cool

the entire enclosed environment. They act as

“heat exchangers”, requiring an interior unit

(evaporator) to blow cool air into the interior

and an exterior unit (condenser) to exhaust

exchanged heat to the outdoors.

• Unlike conventional air conditioners, the

MovinCool Office Pro 60 is a spot cooler which

directs cool air to particular areas or objects.

MovinCool Office Pro 60 has the following features:

2.2 Compact Design

• The innovative design of MovinCool Office Pro

60 has resulted in one compact unit, replacing

the need for two separate units.

2.3 Easy Transportation and

Installation

• With the whole cooling system built into one

compact unit, MovinCool Office Pro 60

requires no piping and can be easily

transported and installed.

2.4 Energy Conservation

• MovinCool Office Pro 60 is economical

because it cools only the area or objects which

need to be cooled.

I000501

Condenser

(Outdoor Unit)

Evaporator

(Indoor Unit)

I001905

Operation Section

8

3. CONSTRUCTION

3.1 Exterior Dimensions

I001906

(40.8)

(8.5)

(2.6)

(29.9)

(3.6)

(51.6)

(Unit: inch)

(30.2)

(55.0)

(DIA. 15.7)

(62.2)

(6.1)

(65.0)

(10.0)

(27.6)

(18.7)

(2.4)

(3.6)

(2.6)

Operation Section

9

3.2 Exterior Components

I001907

Cold Air Outlet Grill

Evaporator Air Inlet Grill

Condenser Air Outlet Duct

Service PanelPower CordCondenser Air Inlet Panel

Caster

Operation Panel

Operation Section

10

3.3 Internal Structure

3.4 Basic Construction

• The MovinCool Office Pro 60 is compact in construction because the condenser and the

evaporator are enclosed in one unit. The interior is divided into three sections. The upper front

face is equipped with the evaporator, and the lower front face contains the condensate pump

and optional drain tanks. The rear section contains the condenser, the compressor and the

control box.

I001908

Evaporator

Fan

(Evaporator)

Fan

(Condenser)

Fan Motor

(Condenser)

Fan Motor

(Evaporator)

(Behind Fan)

Control Box

Drain Switch

Compressor

Condensate Pump

Drain Pan

Capillary Tube

High Pressure

Switch

Condenser

Operation Section

11

3.5 Air Flow

• Air drawn from the right side face passes through the condenser which extracts the heat. This

hot air is blown out through the upper exhaust air duct. Air taken in from the front face is cooled

by the evaporator and then blown through the cool air vent. All the air inlets are equipped with

filters, and the exhaust air duct is protected by metal grill.

3.6 Compressor and Fans

• The compressor is hermetically sealed. Two sets of a two-speed fan motor with a centrifugal fan

are used to draw air across the evaporator and condenser.

3.7 Condensate Pump

• The condensate pump and a 20 ft (6 m) drain hose are included with the Office Pro 60 to provide

continuous operation without the need of the drain tanks. The condensate pump has a maximum

head lift of 17 ft (5.2 m) at 230 VAC or 13 ft (4.0 m) at 208 VAC.

3.8 Drain Tanks (optional)

• A set of two 5.0 gal (19 L) drain tanks are supplied as optional accessory for Office Pro 60. When

drain tanks are used instead of condensate pump, the condensate (water) is collected into both

tanks. The drain switch activates and stops the operation when tanks reach the level of

approximately 8.0 gal (30 L).

I001909

Condenser Air In

Evaporator Air In

Exhaust Air Out

Cool Air Out

Operation Section

12

4. SPECIFICATIONS

4.1 Technical Specifications

ITEM SPECIFICATIONS

cinortcelElenaP lortnoCserutaeF cinortcelE

cinortcelElortnoC tatsomrehT

Cooling Capacity

*1

)W 58571/54171( h/utB 00006/00585V 032/802-yticapaC

llorcS citemreHepyT noisserpmoCrosserpmoCtiucriC tnaregirfeR

Wk 98.3V 032 ta tuptuO detaR rotoM

niF etalProtaropavE

niF etalPresnednoC

ebuT yrallipaClortnoC tnaregirfeR

)gk 08.1( bl 79.3/A 014-Rytitnauq desolcnE/tnaregirfeR

Ventilation Equipment For

Evaporator

lagufirtneCepyT naF

m 0003/0033( MFC 0771/0491wol/hgih-wolF riA .xaM

3

/h)

Wk 33.0/06.0V 032 ta wol/hgih-tuptuO detaR rotoM

)aP 422( GWI 9.0erusserP citatS lanretxE .xaM

Ventilation Equipment For

Condenser

lagufirtneCepyT naF

m 0054/0184( MFC 0562/0382wol/hgih - wolF riA .xaM

3

/h)

Wk 29.0/02.1V 032 ta wol/hgih-tuptuO detaR rotoM

)aP 212( GWI 58.0erusserP citatS lanretxE .xaM

zH 06 HP 1 ,V 032/802tnemeriuqeR rewoPscitsiretcarahC cinortcelE

V 352 XAM ,V 891 NIMegatloV .XAM .NIM

Current Consumption-208/230 V

*1

32/29 A

Total Power Consumption-208/230 V

*1

6.6/6.6 kW

Power Factor-208/230 V

*1

99/99 %

A 061tnerruC gnitratS

A 05ezis esuF dednemmoceR

05-6noitarugifnoC gulP AMENdroC rewoP

tf 6 x )eroc-3( GWA 6htgneL x egauG

)dednemmocer( epyt tcatnoc yrD•tupnI mralA eriFnoitcennoC langiS

• No-Voltage Contact Input/Contact

resistance Less than 100 ohm

ssel ro )CA/CD( V 03 ta A 2tuptuO langiS gninraW

(resistive load)

Net weight 623 lb (283 kg)

Operation Section

13

• Specifications are subject to change without notice.

< NOTE >

*1 :Rating Condition: 95 °F (35 °C), 60 %RH

*2 :Measured at 3.28 ft (1 m) from surface of unit.

Operating Condition Inlet air: Maximum 105 °F (41 °C), 50 %RH

Inlet air: Minimum 65 °F (18.3 °C), 50 %RH

Sound Level

*2

With Condenser Duct-high/low 69/67 dB (A)

Without Condenser Duct-high/low 71/69 dB (A)

Max. Duct Equivalent Length-Per Cold Duct Hose/Hot Duct Hose 40/100 ft (12.1/30.5 m)

Condensate Pump 1/30 HP, 230 V, 0.5 A, 75 W,

Discharge: 3/8 in (9.53 mm)

OD barbed

ITEM SPECIFICATIONS

Operation Section

14

4.2 Characteristics (at 230 V)

I001910

65

60

50

55

45

40

20

30

35

25

15

>evruC ecnereffiD erutarepmeT riA looC<>evruC yticapaC gnilooC<

23.4(13)

21.6(12)

19.8(11)

18.0(10)

16.2(9)

14.4(8)

12.6(7)

10.8(6)

9.0(5)

68(20)

77(25)

86(30)

95(35)

7.2(4)

Delta-T °F (°C)

Dry Bulb Temp. °F (°C)

Wet Bulb Temp. °F (°C)

(25)

77

(20)

68

(35)

95

(30)

86

(15)

59

(10)

50

Cooling Capacity (x10

3

Btu/h)

Relative Humidity (%)

30 40 50 60 70 80

Current Consumption (A)

Power Consumption (kW)

>evruC noitpmusnoC tnerruC<>evruC noitpmusnoC rewoP<

8.0

7.0

6.0

5.0

4.0

68(20)

77(25)

86(30)

95(35)

68(20)

77(25)

86(30)

95(35)

(25)

77

(20)

68

Wet Bulb Temp. °F (°C)

(35)

95

(30)

86

(25)

77

(20)

68

Operation Section

15

4.3 Characteristics (at 208 V)

I001911

65

60

50

55

45

40

25

35

40

30

20

>evruC ecnereffiD erutarepmeT riA looC<>evruC yticapaC gnilooC<

23.4(13)

21.6(12)

19.8(11)

18.0(10)

16.2(9)

14.4(8)

12.6(7)

10.8(6)

9.0(5)

68(20)

77(25)

86(30)

95(35)

7.2(4)

Delta-T °F (°C)

Dry Bulb Temp. °F (°C)

Wet Bulb Temp. °F (°C)

(25)

77

(20)

68

(35)

95

(30)

86

(15)

59

(10)

50

Cooling Capacity (x10

3

Btu/h)

Relative Humidity (%)

30 40 50 60 70 80

Current Consumption (A)

Power Consumption (kW)

>evruC noitpmusnoC tnerruC<>evruC noitpmusnoC rewoP<

8.0

7.0

6.0

5.0

4.0

68(20)

77(25)

86(30)

95(35)

68(20)

77(25)

86(30)

95(35)

(25)

77

(20)

68

Wet Bulb Temp. °F (°C)

(35)

95

(30)

86

(25)

77

(20)

68

Operation Section

16

5. REFRIGERANT SYSTEM

5.1 Refrigerant System Construction

The component parts of the refrigerant system include the following:

• Compressor, Evaporator, Condenser, Capillary tube, High Pressure Switch

These parts are all connected by copper tubing. All the connections have been brazed.

I001912

Condenser

Evaporator

Condenser

Compressor

Suction Pipe

Condenser

Inlet Pipe

Compressor

Discharge Pipe

Compressor

Condenser

Outlet Pipe

Evaporator

Inlet Pipe

Capillary

Tube

Evaporator

Outlet Pipe

Condenser

Fan

Evaporator

Fan

Evaporator

Compressor

Capillary

Tubes

Flow of Refrigerant

Operation Section

17

5.2 Compressor

• The compressor used for the unit is hermetically sealed. The compressor and the compressor

motor are in one casing.

(1) Compressor theory of operation

• The scroll utilizes an involuted spiral which, when matched with a mating scroll form, generates

a series of crescent-shaped gas pockets between the two members. During compression, one

scroll remains stationary (fixed scroll) while the other form (orbiting scroll) is allowed to orbit (but

not rotate) around the first form. As this motion occurs, the pockets between the two forms are

slowly pushed to the center of the two scrolls while simultaneously being reduced in volume.

When the pocket reaches the center of the scroll form, the gas, which is now at a high pressure,

is discharged out of a port located at the center. During compression, several pockets are being

compressed simultaneously, resulting in a very smooth process. Both the suction process (outer

portion of the scroll members) and the discharge process (inner portion) are continuous.

(2) Compressor operation

1) Compression in the scroll is created by the interaction of an orbiting spiral and a stationary spiral.

Gas enters the outer openings as one of the spirals orbits.

2) The open passages are sealed off as gas is drawn into the spiral.

3) As the spiral continues to orbit, the gas is compressed into two increasingly smaller pockets.

4) By the time the gas arrives at the center port, discharge pressure has been reached.

5) Actually, during operation, all six gas passages are in various stages of compression at all times,

resulting in nearly continuous suction and discharge.

< NOTE >

When the compressor shuts off, the compressor motor may run backward for a moment or two

until internal pressures is equalized. This has no effect on compressor durability but may cause

an unexpected sound after the compressor is turned off and should not be diagnosed as a

malfunction.

I001767

1㧕 3㧕 4㧕 5㧕2㧕

Operation Section

18

5.3 Condenser

• The condenser is a heat exchanger with copper tubes that are covered with thin aluminum

projections called plate fins.

• Heat is given off and absorbed by air being pulled across the condenser fins by the centrifugal

fan and then expelled through the exhaust air duct.

5.4 Capillary Tube

• The capillary tube is a long thin tube utilizing

line flow resistance to serve as an expansion

valve. The length and the inner diameter of the

capillary tube are determined by the capacity of

the refrigeration system, specified operating

conditions, and the amount of refrigerant. The

capillary tube causes the high pressure, high

temperature liquid refrigerant sent from the

condenser to expand rapidly as the refrigerant

is sprayed out through the fixed orifice in the capillary tube. As a result, the temperature and

state of the refrigerant becomes low and mist-like respectively, causing it to evaporate easily.

5.5 Evaporator

• The evaporator, like the condenser, is a heat exchanger covered with plate fins. Heat is removed

from the air being pulled across the evaporator by the centrifugal fan and the resulting cool air

is expelled through the cool air vent.

5.6 High Pressure Switch

• The high pressure switch prevents the

condenser and compressor from being

damaged by excessively high pressure in the

high pressure line of the refrigeration cycle.

The switch is normally closed. The snap disk

responds to the variations in pressure and, if

pressure is abnormally high, the snap disk

moves down to push the pin down, causing the

internal contacts to open. This interrupts the

ground signal at the control board (J104 connector) which turns the compressor off.

• Possible causes of this trouble include:

- The condenser air filter is dirty, restricting air flow.

- The condenser blower is defective.

I001887

High Temp./High Pressure

Liquid Refrigerant

Low Temp./Low Pressure

Gas and Liquid Mixture

I001768

Pressure of Refrigerant

Movable Point

Snap Disk

Terminal

Lead Wires

Stationary Point

Molding by Resin

Case

Operation Section

19

6. ELECTRICAL SYSTEM

6.1 Circuit Diagram and Control Box

I001913

TB2

TB1

G

AC 208/230 V 1φ 60 Hz

AP

G

T1

TB1

3L2

1L1

HI

LO

MF2

2T1

5L3

MCC

MC

MDP

Condensate Pump

RTH THS DS

CB

HPRS

TB2

L-

J106

J108

J105

J101 J102 J103 J104

J201

L+

E-

E+

3

2

1

IOLC

IOLF

MF1

IOLF

CC

12

CF2

12

CF1

12

G

ODSFDS

4T2

6T3

A1

A2

TRR1

J9

J10

RB

J8

J7

J6

J5

J4

J3

J2

J1

AP

TB1

TB2

CB

RB

MF1

MF2

MC

CF1

CF2

CC

Attachment Plug

Terminal Block

Control Board

Relay Board

Condenser Fan Motor

Evaporator Fan Motor

Compressor Motor

Capacitor for Condenser Motor

Capacitor for Evaporator Motor

Capacitor for Compressor

IOLF

IOLC

DS

THS

RTH

G

HPRS

MCC

MDP

FDS

ODS

Inner Overload Relay of Fan Motor

Inner Overload Relay of Compressor

Full Drain Warning Switch

Freeze Protection Thermistor

Room Thermistor

Grounding

High Pressure Switch

Relay for Compressor and Condenser Fan Motor

Condensate Pump Motor

Drain Float Switch

Drain Overflow Switch

Terminal Block

(Signal Connection)

Relay Board Fuse

Relay Board

Relay

Terminal Block

Dip Switch

Fan Capacitor

(Condenser)

Fan Capacitor

(Evaporator)

Compressor

Capacitor

Operation Section

20

6.2 Basic Operation of The Office Pro 60 Electrical Circuit

• There are two basic components used to control the operation of the Office Pro 60 electrical

system:

- Control panel assembly

- Control box

• The control panel assembly contains the control panel, control board (with inputs for the freeze

and room temperature thermistors), drain switch, high pressure switch and a microprocessor.

(1) Fan mode

High Fan Mode

• When the FAN MODE button on the control panel is pressed, the microprocessor turns on “FAN

HI” “COOL OFF” indication of LCD and activates both the fan on relay and fan mode relay. This

sends line voltage (208/230 VAC) from the fan on relay to the N.O. (normally open) contacts of

the fan mode relay. This output is connected to the J8 terminal (relay board) where the high

speed wire of the fan motor is connected.

• When this button is pressed again, fan turns to low mode (see below). Press again, fan stops.

• High fan mode is automatically switched

depending on room temperature. When room

temperature is decreased down to 80 °F

(27 °C) or below, fan mode is switched to

HIGH. When room temperature is increased to

88 °F (31 °C) or higher, fan mode is switched

from HIGH to LO.

Low Fan Mode

• When the FAN MODE button on the control panel is pressed again, the microprocessor turns on

“FAN LO” “COOL OFF” indication of LCD and activates both the fan on relay and fan mode relay.

This sends line voltage (208/230 VAC) from the fan on relay to the N.C. (normally closed)

contacts of the fan mode relay. This output is connected to the J7 terminal (relay board) where

the low speed wire of the fan motor is connected.

• When this button is pressed again, fan stops.

I001914

80 °F

(27 °C)

Room Temperature

(High)

(LO)

Condenser Fan

88 °F

(31 °C)

Page is loading ...

Movincool Office Pro 12 / Office Pro 18 / Office Pro 24 Owner's manual

This manual is also suitable for

Movincool Office Pro 12 / Office Pro 18 / Office Pro 24 Owner's manual

Related papers

Other documents