© ®
P S I
G P M
Single Handle Pull-out Bathroom Faucet
STANDARDS
Tools:
PLUMBERS PUTTY FLASHLIGHT BASIN WRENCH
SAFETY GLASSES SCREWDRIVER
PLIERSCHANNELLOCKS ADJUSTABLE WRENCH
HEX-KEY TAPE
Attention:
Helpful Information
Flow Rate Chart
Important
Eleganzia
2017-12-22 MAAN4320-1
SEALED-TUBE
Please keep the tools for future use!
ASME A112.18.1/CSA B125.1
ASME A112.18.2/CSA B125.2
LISTED IAPMO/cUPC
Gather the necessary tools as shown below to complete the installation of
this faucet. Some may not be needed depending on the model of faucet you
are installing. Check with your local hardware store on the requirements of
your installation situation.
WARNING:
For easy installation, you will need:
- To read all the installation instructions completely before beginning.
- To read all the warning, attention and maintenance information.
- To purchase the proper supply lines.
Tighten connection with two wrench to prevent
damage to tube body. Be careful not to bend the
stem as this will void the product warranty.
Faucet Installation
1
2
Tools might be applied to the following places:
Installation size map
Position the faucet, o-ring on the installation
surface.
Adjust the position of the faucet and
secure it with the fixing kit as shown.
3 9/16 in.
(90.2 mm)
6 3/16 in.
(157 mm)
3 7/16 in.
(86.8 mm)
2 1/16 in.
(52 mm)
7 5/16 in.
(185.2 mm)
1 3/8 in.
(35 mm)
1/2-14NPSM
1 3/8 in.
(35 mm)
Checking and Testing
Maintenance:
3
5
Connect the flexible hoses to water
supply valves (not included) and
copper tubes, and tighten it with
adjustable wrench. DON'T OVER
TIGHTEN!
Caution: make sure the hot and
cold flexible hose are connected to
supply valves correctly.
Warning: The supply valves are
not included, please purchase
them at your local hardware store.
6
Remove the aerator by hand. Turn
the faucet handle all the way on,
turn on hot and cold water supply
and flush water lines for one
minute.
Check all connections at arrows for
leaks, retighten if necessary.
BUT DON’T OVERTIGHTEN
Simply rinse the surface with clear water or
mild liquid detergents (if necessary). Dry the
faucet with a clean soft cotton cloth. Do not
use any cleaning agents containing acids
polish abrasives or harsh cleaners.
Connect to water supply lines with either
risers with the coupling nuts or
supplied tube head interior connector or
4
A. B. C.
1. Clean it with water and dry it with soft cloth.
2. Clean the product with gentle liquid or glass cleaner.
3. Don't use acid cleaner.
4. Don't clean with abrasive material, abrasive paper or knife.
Parts listCleaning and care
Daily cleaning and care are required in order to keep the product shining and working properly.
NO. PART NAME
Handle1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
Screw
Index
Trim cap
Cartridge lock nut
Cartridge
Watersaving piece
Cartridge pretend sleeve
O-ring
O-ring
Anti-splash
Spout
Body
O-ring
Screw
Screw
O-ring
Copper tube
Copper tube
20
Screen filter
Clamp
21
22
23
24
25
Nut
Allen key
Washer
Flexible hose
1
2
3
4
5
6
7
8
9
10
12
13
14
15
16
21
22
23
11
24
17
18
20
19
25
-
1
-
2
-
3
-
4
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Whitehaus Collection WH2070800-ORBH Installation guide
-
Whitehaus Collection WH2070826-C Installation guide
-
ANZZI LSAZ074-097B Installation guide
-
Roswell 102112-BAF-PC Installation guide
-
-
-
-
Unbranded LSAZ055-095B Installation guide
-
ANZZI Bravo L-AZ030 Installation guide
-
