Elpro Technologies 450U-E Quick start guide

Brand: Elpro Technologies

Model: 450U-E

Category: WLAN access points

Type: Quick start guide

Elpro Technologies 450U-E is a wireless ethernet modem and device server that allows you to connect devices to a network wirelessly. It can be used to create a bridge network between two or more devices, or to connect a device to a network without the need for an Ethernet cable. The 450U-E is easy to set up and use, and it supports a variety of security features to keep your network safe.

Some of the key features of the 450U-E include:

Wireless connectivity: The 450U-E uses wireless technology to connect to other devices on your network. This means that you don't need to run Ethernet cables between devices, which can be a hassle.

Some of the key features of the 450U-E include:

Wireless connectivity: The 450U-E uses wireless technology to connect to other devices on your network. This means that you don't need to run Ethernet cables between devices, which can be a hassle.

450U-E WIRELESS ETHERNET MODEM AND DEVICE SERVER QUICK START GUIDE

www.cooperbussmann.com/wirelessresources

10/16 Page 1 of 2 Version 1.0

Setting Up a Bridge Network with Two 450U-E Radios

The following procedures provide instructions on how to connect a computer to the 450U-E,

configure the essential radio parameters, and then set up a bridged network between two modules.

Configure a PC to Connect to the 450U-E

1. On the PC Control Panel, open Network and Sharing Center-->Change Adapter Settings

-->Local Area Connection.

The following instructions are for Windows 7

. Earlier Windows operating systems have

similar settings.

2. Open Properties of Local Area Connection.

3. Select “Internet Protocol Version 4 (TCP/IPv4)” and click Properties (Figure 1).

4. Select “Use the following IP address” (Figure 2).

5. Enter an IP address in the range192.168.0.XXX, where “XXX” is an IP address that will not

conflict with any other device that may be connected on the same network.

6. Enter the subnet mask 255.255.255.0, and click OK. Click OK again, and then click Close to

return to the Network Connections window.

Figure 1 Local Area Connection Properties Figure 2 Internet Protocol Version Properties

7. On the module, set the Run/Setup DIP switch (located on the bottom) to the SETUP position.

8. Connect an Ethernet cable between the 450U-E and the PC.

9. Apply power to the SUPPLY terminals (9–30 Vdc) on the module.

10. Open Internet Explorer

version 7 or greater, and enter the default IP address of the module

into the address bar.

You do not need to enter “http” or “www” or any other prefix.

The module’s Setup Mode IP address is on the label on the back of the module.

11. Step through any security warnings, and when prompted enter the username “user” and the

password “user” (case sensitive).

12. When connected to the module, set the Run/Setup DIP switch back to the RUN position.

• If the modem is new and never been configured, or it has been reset to its factory

default settings, the Locale page appears (Figure 3). Go on to step 13.

• If the module has been previously configured, the home page appears. Skip step 13

and go on to the next procedure.

13. If the Locale page appears, select the appropriate locale from the drop down list, and then

click Save and Activate Changes. Go on to the next procedure.

The table on this page shows the available locales and frequency ranges obtainable from

the radio hardware. When you click Save and Activate Changes, the Quick Start page

appears.

Figure 3 Locale Page

450U-E WIRELESS ETHERNET MODEM AND DEVICE SERVER QUICK START GUIDE

10/16 Page 2 of 2 Version 1.0

www.cooperbussmann.com/wirelessresources

Configure the Radio Parameters

Next, you will configure the essential radio parameters required for the modems to communicate

with each other. These parameters must be the same for all modems that are communicating

within the system, and also need to be implemented for a bridge network.

1. If the Quick Start page is not already displayed, click Quick Start on the home page menu.

2. On the Quick Start page, configure the following radio parameters in accordance with your

radio license and the regulations of your country:

• Transmit Power Level

• Transmit Data Rate

• Frequency Step Size

3. Continue to the next procedure to configure a bridge network.

Bridge Network Configuration

1. Assign the operating mode of the first modem to be an access point.

2. Create a system address (ESSID) and record as all radios In the system must use the same

ESSID (case sensitive).

3. By default, the 450U-E is configured with WPA2 encryption. Enter a passphrase and make

a note of the passphrase for later reference.

All radios in the system must use the same encryption method and key (case sensitive).

4. Enter the IP address required for your network.

Each radio In the system must have a different IP address, typically within the same subnet

(for example, 192.168.0.120, 192.168.0.121, and so on).

5. Click Save Changes and Reset.

6. Repeat steps 1 through 5 on the other radios, except select “Client” in the Operating Mode

field.

NOTE Make sure that the IP address is unique to each modem, the ESSID and

encryption methods are the same as the access point, and the radio conﬁguration

parameters are the same for all radios.

7. After all parameters are entered and saved, make sure to reset the modems.

8. When all the modems have restarted, connect the antennas and confirm that the Link LED

is on, indicating that a connection has been made.

NOTE It is important to perform the link check while the modems are on the bench,

rather than at their ﬁnal destination. The normal link time between an access point

and a client will be less than 30 seconds after the modems have ﬁnished restarting.

Figure 4 Home Page

Figure 5 Quick Start Page

Figure 6 Bridge Network

• Transmit Frequency

• Receive Frequency

Elpro Technologies 450U-E Quick start guide

Brand: Elpro Technologies

Model: 450U-E

Category: WLAN access points

Type: Quick start guide

Some of the key features of the 450U-E include:

Wireless connectivity: The 450U-E uses wireless technology to connect to other devices on your network. This means that you don't need to run Ethernet cables between devices, which can be a hassle.

Download PDF

report

Elpro Technologies 450U-E Quick start guide

Elpro Technologies 450U-E Quick start guide

Related papers

Other documents