45˚
PLUG TUB
OUTLET
5-7/8"
Installation
Instructions
Certied to comply with ANSI A112.18.1
Recommended Tools & Materials
ROUGHING-IN DIMENSIONS
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
Electric Drill
Torch
6mm (15/64")
Drill Bit
Pencil
Phillips Screwdriver
Hammer
COMMERCIAL SHOWER
SYSTEM KITS: 1.5 gpm & 2.5 gpm
1662SG.212
1662SG.222
TOP OF TUB RIM
BOTTOM OF TUB
74" FOR HEAD
CLEARANCE
4"
18"
OPTIONAL
5-1/8" REF.
12"
OPTIONAL
12"
OPTIONAL
1/2"
COPPER
1/2" SUPPLIES
6" DIA.
1" MIN.
8"
Universal Inlets / Outlets:
1/2" NOM Copper Sweat or 1/2" NPT
1-1/4"
1/2"
1/2" NPT
FINISHED WALL
2-3/4" DIA.
Adjustable Wrench
10'
Pipe Wrench
Tubing Cutter
Tape
Measure
Sealing Tape
Installation must conform to all local building codes.
1660766.002
(1.5 gpm)
1660767.002
(2.5 gpm)
3-5/16"
8-1/8"
1/2" NPSM
OPTIONAL
1662SG.212 (1.5gpm)
1662SG.222 (2.5gpm)
48"
1-5/8"
36"
37-1/2"
FINISHED
WALL
3-1/8" DIA.
OPTIONAL TO FINISHED FLOOR
USUALLY BETWEEN
36"
60"
TO
3-1/8" DIA.
3-1/8" DIA.
M965667 Rev. 1.0 (1/17)
M965667 Rev. 1.0 (1/17)
1
When nished tiling the wall, remove PLASTER GUARD.
Remove cap from tub supply pipe.
REFER TO INSTALLATION INSTRUCTIONS (M968763) SUPPLIED WITH VALVE
TRIM KIT FOR COMPLETE INSTALLATION AND REPAIR PART INFORMATION.
NOTE
MAKE ALL CONCEALED PIPING CONNECTIONS
INSTALL VALVE TRIM
3
4
See Roughing-in diagram before starting.
Make Hot and Cold supply connections to the VALVE BODY. Inlet and outlet connections to the valve body are 1/2" copper sweat.
Make Tub Filler connection from DIVERTER. (Use the port with the BATH TUB picture). DIVERTER IS 1/2" NPT. TUB SPOUT
connection is 1/2" copper for SLIP-ON SPOUT.
Make the connections for the HAND SHOWER. The HAND SHOWER connections are 1/2" NPT.
For support, use PIPE BRACES secured to wooden braces. Cap off HAND SHOWER and TUB SPOUT FILLER PIPE.
With the R120SS VALVE turned off, turn on water supplies. Check for leaks.
Finish all wall construction.
CAP
PLASTER GUARD
INSTALL THE R422 TWO-WAY DIVERTER
2
TWO-WAY
DIVERTER
REFER TO INSTALLATION INSTRUCTIONS (M965673) SUPPLIED WITH DIVERTER
FOR COMPLETE INSTALLATION AND REPAIR PART INFORMATION.
The reverse side of the body is marked with arrows.
CAUTION: Do not solder near the VALVE. Damage to the SEAL may occur. Do not seal
any outlets. The DIVERTER cannot be used as a stop valve. Use thread sealant or sealing
tape on threaded connections.
NOTE
IMPORTANT
1/2" NPT INLET
1/2" NPT
SHOWER
1/2" NPT HAND
SHOWER
See Roughing-in diagram before starting. The port with the BATH TUB picture is the high ow.
The DIVERTER can be installed with the inlet rotated in any position.
All connections are 1/2" NPT.
For proper positioning the nished wall must be within the side of PLASTER GUARD.
Connect the R422 TWO-WAY DIVERTER to the R120SS VALVE BODY.
1/2" SWEAT PLUG
INSTALL THE R121SS VALVE BODY
R121SS
When soldering, remove PLASTER GUARD, CARTRIDGES and CHECK STOPS
(IF PRESENT). When finished soldering, flush valve body, replace cartridges, check stops
(if present) and plaster guard to continue installation. Use thread sealant or Teflon tape
on threaded connections.
NOTE
IMPORTANT
See Roughing-in diagram before starting.
Connections are:
1/2" NOM Copper Sweat or 1/2" NPT inlets
1/2" NOM Copper Sweat or 1/2" NPT tub and shower outlets
REFER TO INSTALLATION INSTRUCTIONS (M965661) SUPPLIED WITH VALVE BODY FOR
COMPLETE INSTALLATION AND REPAIR PART INFORMATION.
M965667 Rev. 1.0 (1/17)
INSTALL WALL SUPPLY
1/2" NPT
APPLY SEALANT
OR SEALING TAPE
Supply to WALL SUPPLY is 1/2" NPT. See rough-in above for detailed information.
Apply sealant or sealing tape to threads of 1/2" NPT supply nipple.
6
INSTALL HOSE AND HAND SHOWER
TEST SHOWER SYSTEM
7
Turn on water supplies and check all fuctions of of the SHOWER
SYSTEM KIT. Check for any leaks.
INSTALL DIVERTER TRIM AND HANDLE
5
PLASTER GUARD
MAX
When nished tiling the wall, remove PLASTER GUARD.
Place ESCUTCHEON (1) onto ESCUTCHEON HOLDER (2).
Thread ESCUTCHEON HOLDER (2) onto DIVERTER VALVE (3).
Tighten until ESCUTCHEON (1) is snug against nished wall.
Install HANDLE SKIRT (4) onto VALVE STEM (5).
Push DECORATIVE RING (6) onto LEVER HANDLE (7).
Align LEVER HANDLE (7) and push onto
HANDLE SKIRT (4). Install HANDLE
SCREW (8) and tighten.
Push INDEX CAP (9) into LEVER
HANDLE (7).
1
5
6
7
8
9
2
4
3
Install SEAL (1) into COUPLING NUT (2). Connect COUPLING NUT (2)
to WALL SUPPLY NIPPLE (3) and tighten.
INSTALL second SEAL (4) into SPRAY HOSE END (5) and connect
HAND SHOWER (6) to SPRAY HOSE END (5). Hand tighten.
6
4
5
1
3
2
M965667 Rev. 1.0 (1/17)
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH
WITH A COARSE SURFACE.
8
INSTALLATION INSTRUCTIONS
OPTIONAL TO FINISHED FLOOR
USUALLY BETWEEN
FINISHED
FLOOR
915mm
(36")
1525mm
(60")
TO
914mm
(36")
The SLIDE BAR (1) works best when secured to the wall studs or cross brace using WOOD SCREWS. If mounting
into the studs is not possible, use appropriate wall fasteners provided to secure the installation.
Mark a vertical center line in the location you wish to install the SLIDE BAR (1). NOTE: The height from the finished
floor is optional. See rough-in drawing for suggested dimensions.
Determine desired height from the nished oor to the lower support and mark a horizontal center line. Slide the two
WALL ESCUTCHEONS (5) away from the MOUNTING FLANGES (3). Position the SLIDE BAR (1) as shown in Fig. A and
mark the location of the six mounting holes to be drilled. Fig. A. Using a #10 masonry drill, drill six mounting holes
1-1/4" max. deep. Fig. B.
Install the six ANCHORS (2) provided into the mounting holes. Use a hammer to lightly tap ANCHORS (2) into place.
Make sure they are installed ush against the nished wall. Fig. B.
Align and place the SLIDE BAR MOUNTING FLANGES (3) over the installed ANCHORS (2). Secure the SLIDE BAR (1)
to the wall with the SCREWS (4) provided. Fig. B.
Push WALL ESCUTCHEONS (5) against nished wall. Rotate WALL ESCUTCHEONS (5) clockwise to lock into
position. Fig. C.
Check operation of SLIDE BAR (1) by rotating HOLDER LEVER (7) and moving HAND SHOWER HOLDER (9) up and down.
Rotate LEVER HANDLE (7) back to lock HAND SHOWER HOLDER (6). Fig. B.
2
LEVEL
VERTICAL
CENTER LINE
DRILLED
MOUNTING
HOLES
ROTAT E
CLOCKWISE
TO LOCK
LOCK
UNLOCK
LARGE
DIAMETER UP
C/L
6
1 1
1
8
7
3
4
5
5
5
Fig. A Fig. B Fig. C
Make sure larger diameter side of SPRAY HOLDER (6) is facing upward. If not rotate SPRAY HOLDER (6) 180 dergees.
Rotate the LEVER HANDLE (7) to the unlocked position. Push the SPRAY HOLDER (6) side onto the SLIDE BAR (1).
Push the LEVER HANDLE SIDE (7) over the SPRAY HOLDER ARMS (8) until the two snap togerther.
M965667 Rev. 1.0 (1/17)
954027-002OA
ESCUTCHEON HOLDER
012157-0020A
HANDLE SKIRT
012673-0020A
LEVER HANDLE
012205-0070A
COLOR RING KIT
012189-0020A
INDEX BUTTON
918572-0070A
HANDLE SCREW
MODEL NUMBER
MODEL NUMBER
T675.500
8888.056
MODEL NUMBER
R121SS
012288-0020A
ESCUTCHEON KIT
M952100-0070A
PRESSURE BALANCING UNI
023529-0070A
CARTRIDG
023603-0070A
CARTRIDGE SCREWS
051122-0070A
SCREWDRIVER STOPS
050145-0070A
1/2" SWEAT PLUG
PRESSURE BALANCE
TEMPERATURE/VOLUME
CONTROL VALVE
COLONY SOFT
TRIM
MODEL NUMBER
R422
2-WAY DIVERTER
VALVE
MODEL NUMBER
T342.430
HERITAGE HANDLE
DIVERTER TRIM
TUB SPOUT
M961854-0070A
FIXATION RING WITH SCREWS
PLASTER
GUARD
MA
X
M964432-0070A
DIVERTER REPAIR KIT
060219-0070A
STEM KIT
051310-0070A
SPRING KIT
051309-0070A
CAP
912647-0070A
CAP SEAL
912737-0070A
STEM O-RING
M961856-0020A
ESCUTCHEON AND SCREWS
078016-0020A
ESCUTCHEON SCREWS
M909606-0020A
DECAL
M907050-0020A
ESCUTCHEON CAP SET
8888.056-0020A
SPOUT (Slip-on)
M961636-0020A
LEVER HANDLE KIT
030126-0070A
HANDLE SCREW KIT
013205-0070A
STOP VALVE O-RING
CHROME 002
Appropriate nish code
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 442-1902
Mon. - Fri. 8:00 a.m. to 8:00 p.m. EST
Saturday 10:00 a.m. to 4:00 p.m. EST
IN CANADA 1-800-387-0369
(TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
Product names listed herein are trademarks of AS America, Inc. © AS America, Inc. 2017
TWO WAY
BODY
M965667 Rev. 1.0 (1/17)
8888.037.002
WALL SUPPLY
8888.035.002
METAL HOSE
1660.236.002
36" SLIDE BAR
8888037.002
WALL SUPPLY
030782-0020A
HOSE KIT
M962520-0020A
CHECK VALVE
3-FUNCTION HAND
SHOWER
1660766.002
(1.5 gpm)
1660767.002
(2.5 gpm)
M9641800020A
SPRAY HOLDER
ASSEMBLY
M964179-0070A
MOUNTING KIT
CHROME 002
Appropriate nish code
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 442-1902
Mon. - Fri. 8:00 a.m. to 8:00 p.m. EST
Saturday 10:00 a.m. to 4:00 p.m. EST
IN CANADA 1-800-387-0369
(TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
Product names listed herein are trademarks of AS America, Inc. © AS America, Inc. 2017
-
1
-
2
-
3
-
4
-
5
-
6
American Standard 1662SG.212.002 Installation guide
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
American Standard 1662SG.215.002 Installation guide
-
-
-
-
-
-
-
-
-
Other documents
-
Franke 0738024 Datasheet
-
-
-
-
Signature Hardware 354411 Installation guide
-
Boyel Living RB0710 Installation guide
-
Delta RP90159PCPR Installation guide
-
Ovios TH8045 Installation guide
-
-
Duravit CE4210012 Specification Manual
