H3C S3100-16T P-EI-W Quick start guide

H3C S3100 Series Ethernet Switches

Quick Start (For Soliton)

Hangzhou H3C Technologies Co., Ltd.

http://www.h3c.com

Manual Version: T2-08011H-20080410-C-1.00

and its licensors

No part of this manual may be reproduced or transmitted in any form

or by any means without prior written consent of Hangzhou H3C

Technologies Co., Ltd.

Trademarks

H3C, , Aolynk, , H

3

Care,

, TOP G, , IRF,

NetPilot, Neocean, NeoVTL, SecPro, SecPoint, SecEngine, SecPath,

Comware, Secware, Storware, NQA, VVG, V

2

G, V

n

G, PSPT, XGbus,

N-Bus, TiGem, InnoVision and HUASAN are trademarks of Hangzhou

H3C Technologies Co., Ltd.

All other trademarks that may be mentioned in this manual are the

property of their respective owners.

Notice

The information in this document is subject to change without notice.

Every effort has been made in the preparation of this document to

ensure accuracy of the contents, but all statements, information, and

recommendations in this document do not constitute the warranty of

any kind, express or implied.

To obtain the latest information, please access:

http://www.h3c.com

Technical Support

customer_service@h3c.com

http://www.h3c.com

About This Manual

Related Documentation

In addition to this manual, each H3C S3100 Series Ethernet

Switches documentation set includes the following:

Manual Content

H3C S3100 Series Ethernet

Switches Operation Manual

(For Soliton)

It is used for assisting the users

in data configurations and

typical applications.

H3C S3100 Series Ethernet

Switches Command Manual

(For Soliton)

It is used for assisting the users

in using various commands.

H3C S3100 Series Ethernet

Switches Installation Manual

(For Soliton)

It is used for assisting the users

in switch installation, booting up,

hardware and software

maintenance.

Organization

H3C S3100 Series Ethernet Switches Quick Start (For Soliton) is

organized as follows:

Chapter Contents

1 Product Overview

Introduces the characteristics and

technical specifications of S3100

Series Ethernet Switches.

Chapter Contents

2 Installation Preparation

Introduces the installation

preparation and precaution of

S3100 Series Ethernet Switches.

3 Installation

Introduces the procedures to install

an S3100 Series Ethernet Switch,

including the setup of the

mainframe, cards and cables.

4 Lightning Protection of the

Switch

Introduces lightning protection of

S3100 Series Ethernet Switches.

Conventions

The manual uses the following conventions:

I.

Symbols

Convention Description

Warning

Means reader be extremely careful.

Improper operation may cause bodily

injury.

Caution

Means reader be careful. Improper

operation may cause data loss or damage

to equipment.

 Note Means a complementary description.

Environmental Protection

This product has been designed to comply with the requirements

on environmental protection. For the proper storage, use and disposal

of this product, national laws and regulations must be observed.

Quick Start (For Soliton)

H3C S3100 Series Ethernet Switches

Table of Contents

i

Table of Contents

Chapter 1 Product Overview ........................................................1-1

1.1 Overview ............................................................................1-1

1.2 Introduction to S3100 Series Ethernet Switches ...............1-2

1.2.1 S3100-26TP-EI-W ...................................................1-2

1.2.2 S3100-16TP-EI-W ...................................................1-4

1.2.3 S3100-8TP-EI-W .....................................................1-7

1.3 Introduction to Front Panel LEDs.......................................1-9

1.3.1 Power LED ..............................................................1-9

1.3.2 Auto-Sensing 10/100BASE-TX Ethernet Port Status

LED.................................................................................

1-10

1.3.3 1000 Mbps Uplink Port Status LED.......................1-12

1.4 Technical Specifications ..................................................1-12

1.5 SFP Modules Supported by S3100 Series Ethernet

Switches ................................................................................

1-14

Chapter 2 Installation Preparation...............................................2-1

2.1 Precautions ........................................................................2-1

2.2 Requirements on Environment ..........................................2-1

2.2.1 Temperature/Humidity Requirements .....................2-2

2.2.2 Cleanness Requirements ........................................2-3

2.2.3 Anti-interference Requirements...............................2-4

2.2.4 Laser Usage Security ..............................................2-5

2.3 Installation Tools ................................................................2-5

Chapter 3 Installation....................................................................3-1

3.1 Installing a Switch ..............................................................3-1

Quick Start (For Soliton)

H3C S3100 Series Ethernet Switches

Table of Contents

ii

3.1.1 Cabinet Mounting ....................................................3-1

3.1.2 Desk Mounting.........................................................3-9

3.1.3 Wall Mounting..........................................................3-9

3.1.4 Magnet Mounting...................................................3-12

3.2 Connection of Power Cord and Grounding Cable ...........3-16

3.2.1 Connecting AC Power Cord ..................................3-16

3.2.2 Connecting DC Power Cable ................................3-17

3.2.3 Connecting Grounding Cable ................................3-19

3.3 Connecting Optical Fiber .................................................3-24

3.4 Connection of Console Cable ..........................................3-25

3.4.1 Console Cable .......................................................3-25

3.4.2 Connecting Console Cable....................................3-26

3.5 Installation Verification .....................................................3-27

Chapter 4 Lightning Protection of the Switch ............................4-1

4.1 Installation of Lightning Arrester for AC Power (Socket Strip

with Lightning Protection).........................................................

4-1

4.2 Installation of Lightning Arrester for Network Port .............4-4

Quick Start (For Soliton)

H3C S3100 Series Ethernet Switches

Chapter 1 Product Overvie

w

1-1

Chapter 1 Product Overview

1.1 Overview

H3C S3100 Series Ethernet Switches are high-performance,

high-density, easy-to-install, NMS-manageable intelligent Ethernet

switches which support wire-speed Layer 2 switching.

Table 1-1 lists the models of H3C S3100 Series Ethernet

Switches.

Table 1-1 Models of H3C S3100 Series Ethernet Switches

Model

Power

supply

Number of

10/100M

electrical

ports

1000M

uplink

ports

Number of

console

ports

S3100-26T

P-EI-W

AC input or

12V-RPS

DC input

24

2 Combo

ports

1

S3100-16T

P-EI-W

16

2 Combo

ports

1

S3100-8T

P-EI-W

AC input

8

1 Combo

port

1

Quick Start (For Soliton)

H3C S3100 Series Ethernet Switches

Chapter 1 Product Overvie

w

1-2

1.2 Introduction to S3100 Series Ethernet

Switches

1.2.1 S3100-26TP-EI-W

I. Front panel

S3100-26TP-EI-W Ethernet switches each provide twenty-four

auto-sensing 10/100/1000Base-TX Ethernet ports, two

10/100/1000BASE-T Ethernet ports, two 100/1000Base-X SFP ports,

and one console port. Each SFP port and the corresponding

10/100/1000BASE-T Ethernet port form a Combo port. For each

Combo port, either the SFP port or the corresponding

10/100/1000BASE-T Ethernet port can be used at a time.

Figure 1-1 shows the front panel of an S3100-26TP-EI-W

Ethernet switch.

(1) (2) (3) (4) (5)

(6)(7)(8)(9)

(1) Auto-sensing 10/100Base-TX Ethernet port status LED

(2) Link LED for Combo port (3) Console port

(4) Power LED (PWR) (5) RPS DC power LED

(6) A/L LED (7) D/S LED

(8) Mode button (9) Active LED for Combo port

Figure 1-1 Front panel of an S3100-26TP-EI-W Ethernet switch

Quick Start (For Soliton)

H3C S3100 Series Ethernet Switches

Chapter 1 Product Overvie

w

1-3

 Note:

For details about LEDs on the front panel, refer to section 1.3

“

Introduction to Front Panel LEDs”.

II. Rear panel

Figure 1-2 shows the rear panel of an S3100-26TP-EI-W

Ethernet switch.

(1) (2) (3)

(1) AC power socket (2) RPS DC power socket

(3) Grounding screw

Figure 1-2 Rear panel of an S3100-26TP-EI-W Ethernet switch

III. Power system

S3100-26TP-EI-W Ethernet switches can adopt AC input, or RPS

12 VDC input, or both to provide backup. Only the recommended RPS

can be used.

1) AC input:

z Rated voltage range: 100 VAC to 240 VAC, 50 Hz/60 Hz

z Input voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz

2) RPS DC input:

z Rate voltage range: 10.8 VDC to 13.2 VDC

Quick Start (For Soliton)

H3C S3100 Series Ethernet Switches

Chapter 1 Product Overvie

w

1-4

IV. Cooling system

S3100-26TP-EI-W Ethernet switches cool off naturally.

1.2.2 S3100-16TP-EI-W

I. Front panel

S3100-16TP-EI-W Ethernet switches each provide sixteen

auto-sensing 10/100Base-TX Ethernet ports, two 10/100/1000Base-T

Ethernet ports, two 100/1000Base-X SFP ports, and one console port.

Each SFP port and the corresponding 10/100/1000BASE-T Ethernet port

form a Combo port. For each Combo port, either the SFP port or the

corresponding 10/100/1000BASE-T Ethernet port can be used at a time.

Figure 1-3 shows the front panel of an S3100-16TP-EI-W

Ethernet switch.

(1) (2) (3) (4)

(5)(6)(7)(8)

(1) Auto-sensing 10/100Base-TX Ethernet port status LED

(2) Link LED for Combo port (3) Console port

(4) Power LED (PWR) (5) A/L LED

(6) D/S LED (7) Mode button

(8) Active LED for Combo port

Figure 1-3 Front panel of an S3100-16TP-EI-W Ethernet switch

Quick Start (For Soliton)

H3C S3100 Series Ethernet Switches

Chapter 1 Product Overvie

w

1-5

 Note:

For details about LEDs on the front panel, refer to section 1.3

“

Introduction to Front Panel LEDs”.

II. Rear panel

Figure 1-4 shows the rear panel of an S3100-16TP-EI-W

Ethernet switch.

(1) (2)

(1) AC power socket (2) Grounding screw

Figure 1-4 Rear panel of an S3100-16TP-EI-W Ethernet switch

III. Side panel

Each S3100-16TP-EI-W Ethernet switch provides a security slot,

through which you can lock the device together with an irremovable

object to prevent theft.

The security slot is located at the rear end of the left side panel,

as shown in

Figure 1-5.

Quick Start (For Soliton)

H3C S3100 Series Ethernet Switches

Chapter 1 Product Overvie

w

1-6

(1)

(1) Security slot

Figure 1-5 Security slot on left side panel of an

S3100-16TP-EI-W Ethernet switch

 Note:

If the left screw hole above the security slot is used, the security slot

cannot be used.

IV. Power system

S3100-16TP-EI-W Ethernet switches:

z Rated voltage range: 100 VAC to 240 VAC, 50/60Hz

z Input voltage range: 90 VAC to 264 VAC, 47Hz to 63Hz

V. Cooling system

S3100-16TP-EI-W Ethernet switches cool off naturally.

Quick Start (For Soliton)

H3C S3100 Series Ethernet Switches

Chapter 1 Product Overvie

w

1-7

1.2.3 S3100-8TP-EI-W

I. Front panel

S3100-8TP-EI-W Ethernet switches each provide eight

auto-sensing 10/100Base-TX Ethernet ports, one 10/100/1000Base-T

Ethernet port, one 100/1000Base-X SFP port, and one console port.

The SFP port and the 10/100/1000BASE-T Ethernet port form a

Combo port. Either the SFP port or the 10/100/1000BASE-T Ethernet

port can be used at a time.

Figure 1-6 shows the front panel of an S3100-8TP-EI-W Ethernet

switch.

(1) (2) (3) (4)

(5)(6)(7)(8)

(1) Auto-sensing 10/100Base-TX Ethernet port status LED

(2) Link LED for Combo port (3) Console port

(4) Power LED (PWR) (5) A/L LED

(6) D/S LED (7) Mode button

(8) Active LED for Combo port

Figure 1-6 Front panel of an S3100-8TP-EI-W Ethernet switch

Quick Start (For Soliton)

H3C S3100 Series Ethernet Switches

Chapter 1 Product Overvie

w

1-8

 Note:

For details about LEDs on the front panel, refer to section 1.3

“

Introduction to Front Panel LEDs”.

II. Rear panel

Figure 1-7 shows the rear panel of an S3100-8TP-EI-W Ethernet

switch.

(1) (2)

(1) AC power socket (2) Grounding screw

Figure 1-7 Rear panel of an S3100-8TP-EI-W Ethernet switch

III. Side panel

Each S3100-8TP-EI-W Ethernet switch provides a security slot,

through which you can lock the device together with an irremovable

object to prevent theft.

The security slot is located at the rear end of the left side panel,

as shown in

Figure 1-5.

Quick Start (For Soliton)

H3C S3100 Series Ethernet Switches

Chapter 1 Product Overvie

w

1-9

 Note:

If the left screw hole above the security slot is used, the security slot

cannot be used.

IV. Power system

S3100-8TP-EI-W Ethernet switches:

z Rated voltage range: 100 VAC to 240 VAC, 50/60Hz

z Input voltage range: 90 VAC to 264 VAC, 47Hz to 63Hz

V. Cooling system

S3100-8TP-EI-W Ethernet switches cool off naturally.

1.3 Introduction to Front Panel LEDs

1.3.1 Power LED

Table 1-2 Description of the power LED on S3100 series

LED

Mark on

the panel

Status Description

ON The switch is powered on.

Power LED PWR

OFF The switch is powered off.

ON DC input is normal.

RPS DC

power LED

RPS

OFF There is no DC input.

Quick Start (For Soliton)

H3C S3100 Series Ethernet Switches

Chapter 1 Product Overvie

w

1-10

 Note:

Only S3100-26TP-EI-W AC-powered Ethernet switches have an RPS

DC power LED.

1.3.2 Auto-Sensing 10/100BASE-TX Ethernet Port

Status LED

There are two port status LEDs on both sides (yellow LED on the

left and green LED on the right) of each 10/100BASE-TX Ethernet port

of S3100 series. They indicate the active, link, duplex, and speed

statuses of the port.

In addition, there are an A/L LED and a D/S LED on each model

of S3100 series. These two LEDs indicate the mode of the port status

LEDs. When the A/L LED is on, the port status LEDs respectively

indicate the active status and link status of ports. When the D/S LED is

on, the port status LEDs respectively indicate the duplex status and

speed status of ports. Either the A/L LED or the D/S LED is on at a

specific time. For details, see

Table 1-3.

Quick Start (For Soliton)

H3C S3100 Series Ethernet Switches

Chapter 1 Product Overvie

w

1-11

Table 1-3 Description of port status LEDs on S3100 series

Port status

mode LED

Port status LED Description

BLINKING

The port is in the active state

and there is traffic on the port.

Yellow

LED

(left)

OFF

The port is in the active state

but there is no traffic on the

port.

ON

The port is connected

properly.

The A/L

LED is on

Green

LED

(right)

OFF

The port is not connected or

is incorrectly connected.

ON

The port operates in the full

duplex mode.

Yellow

LED

(left)

OFF

The port operates in the half

duplex mode.

ON The port rate is 100 Mbps.

The D/S

LED is on

Green

LED

(right)

OFF The port rate is 10 Mbps.

You can switch the mode of the port status LEDs by pressing the

Mode button. After a switch is powered on, the A/L LED is on initially. If

you press the Mode button, the D/S LED will be on. After that, if you

press the Mode button again within 45 seconds, the A/L LED will be on

again. Otherwise, the A/L LED will automatically be on 45 seconds

later.

Quick Start (For Soliton)

H3C S3100 Series Ethernet Switches

Chapter 1 Product Overvie

w

1-12

1.3.3 1000 Mbps Uplink Port Status LED

Table 1-4 Description of 1000 Mbps uplink port status LED on

S3100 series

LED

Mark on

the panel

Status Description

ON

The port is connected

properly.

1000

Mbps

uplink port

link LED

LINK

OFF

The port is not connected

or is incorrectly connected.

BLINKING

The port is in the active

state and there is traffic on

the port.

1000

Mbps

uplink port

active

LED

ACT

OFF

The port is in the active

state but there is no traffic

on the port.

1.4 Technical Specifications

Table 1-5 Technical specifications for S3100 Series Ethernet

switches

Model

S3100-26TP-

EI-W

S3100-16TP-

EI-W

S3100-8TP-EI

-W

Physical

dimensions (H

x W x D)

43.6 x 440 x

260 mm (1.7 x

17.2 x 10.2 in)

43.6 x 300 x

220 mm (1.7 x

11.8 x 8.7 in)

43.6 x 230 x

200 mm (1.7 x

9.1 x 7.9 in)

Weight <3.5 kg (7.7 lb) <2.5 kg (5.5 lb) <1.8 kg (4 lb)

Quick Start (For Soliton)

H3C S3100 Series Ethernet Switches

Chapter 1 Product Overvie

w

1-13

Model

S3100-26TP-

EI-W

S3100-16TP-

EI-W

S3100-8TP-EI

-W

Number of

fixed ports

24 x

auto-sensing

10/100BASE-

TX Ethernet

port

2 x 1000M

Combo port

16 x

auto-sensing

10/100BASE-

TX Ethernet

port

2 x 1000M

Combo port

8 x

auto-sensing

10/100BASE-

TX Ethernet

port

1 x 1000M

Combo port

Number of

management

port

1 x console port

Power system

S3100-16TP-EI-W/S3100-8TP-EI-W Ethernet

switches support only AC input.

S3100-26TP-EI-W AC-powered switches support

AC input and RPS DC input.

AC input:

z Rated voltage range: 100 VAC to 240 VAC, 50

Hz /60 Hz

z Input voltage range: 90 VAC to 264 VAC, 47

Hz to 63Hz

RPS DC input:

z Input voltage range: 10.8 VDC to 13.2 VDC

PoE (as

powered

device)

Not supported Not supported Not supported

System power

consumption

(full load)

22 W 17 W 14 W

Fan None None None

Operating

temperature

0°C to 45°C (30°F to 113°F)

Quick Start (For Soliton)

H3C S3100 Series Ethernet Switches

Chapter 1 Product Overvie

w

1-14

Model

S3100-26TP-

EI-W

S3100-16TP-

EI-W

S3100-8TP-EI

-W

Relative

humidity (non-

condensing)

10% to 90%

Caution:

Only the recommended 12V-RPS DC power supply can be used for

S3100-26TP-EI Ethernet switches.

1.5 SFP Modules Supported by S3100

Series Ethernet Switches

The front panel of S3100 Series Ethernet switches provides one

or two 1000M SFP ports in which you can select the required small

form-factor pluggable (SFP) modules to insert. For the models of SFP

modules, see

Table 1-6.

Page is loading ...

H3C S3100-16T P-EI-W Quick start guide

This manual is also suitable for

H3C S3100-16T P-EI-W Quick start guide

Related papers

Other documents