H3C S5500-EI Series Ethernet Switches
Installation Manual
Hangzhou H3C Technologies Co., Ltd.
http://www.h3c.com
Manual Version: 20090726-C-1.02
Copyright © 2007-2009, Hangzhou H3C Technologies Co., Ltd. and its licensors
All Rights Reserved
No part of this manual may be reproduced or transmitted in any form or by any means without prior
written consent of Hangzhou H3C Technologies Co., Ltd.
Trademarks
H3C, , Aolynk, , H
3
Care,
, TOP G, , IRF, NetPilot, Neocean, NeoVTL,
SecPro, SecPoint, SecEngine, SecPath, Comware, Secware, Storware, NQA, VVG, V
2
G, V
n
G, PSPT,
XGbus, N-Bus, TiGem, InnoVision and HUASAN are trademarks of Hangzhou H3C Technologies Co.,
Ltd.
All other trademarks that may be mentioned in this manual are the property of their respective owners.
Notice
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute the warranty of any kind, express or implied.
Technical Support
customer_service@h3c.com
http://www.h3c.com
About This Manual
Organization
H3C S5500-EI Series Ethernet Switches Installation Manual is organized as follows:
Chapter Contents
1 Product Overview
Briefly introduces the appearance, system description, as well as
the features and applications of the S5500-EI series switches.
2 Preparing for Installation
Describes the requirements on installation site, the safety
recommendations before and during installation, and the
required tools.
3 Installing the Switch
Covers the procedures for installing the S5500-EI series
switches, ground wire connection, power module installation,
interface module installation, and so on.
4 Starting and Configuring the
Switch
Helps you get familiar with the basic knowledge of how to boot
and configure the S5500-EI series switches, including device
startup, power-on, and initialization of system files, and so on.
5 Boot ROM and Host Software
Loading
Introduces how to load Boot ROM and host software for an
S5500-EI series switch
6 Maintenance and
Troubleshooting
Introduces the problems that might occur during the installation
and the booting of an S5500-EI series switch and the related
solution.
Appendix A Lightning Protection
of the Switch
Introduces lightning protection of S5500-EI Series Ethernet
Switches.
Conventions
The manual uses the following conventions:
Command conventions
Convention Description
Boldface
The keywords of a command line are in Boldface.
italic
Command arguments are in italic.
[ ] Items (keywords or arguments) in square brackets [ ] are optional.
{ x | y | ... }
Alternative items are grouped in braces and separated by vertical bars.
One is selected.
[ x | y | ... ]
Optional alternative items are grouped in square brackets and
separated by vertical bars. One or none is selected.
{ x | y | ... } *
Alternative items are grouped in braces and separated by vertical bars.
A minimum of one or a maximum of all can be selected.
[ x | y | ... ] *
Optional alternative items are grouped in square brackets and
separated by vertical bars. Many or none can be selected.
&<1-n>
The argument(s) before the ampersand (&) sign can be entered 1 to n
times.
# A line starting with the # sign is comments.
GUI conventions
Convention Description
Boldface
Window names, button names, field names, and menu items are in
Boldface. For example, the New User window appears; click OK.
>
Multi-level menus are separated by angle brackets. For example, File >
Create > Folder.
Symbols
Convention Description
Means reader be extremely careful. Improper operation may cause
bodily injury.
Means reader be careful. Improper operation may cause data loss or
damage to equipment.
Means a complementary description.
Related Documentation
In addition to this manual, each H3C S5500-EI Series Ethernet Switches documentation set includes
the following:
Manual Description
H3C S5500-EI Series Ethernet
Switches Operation Manual
It is used for assisting the users in data configurations and typical
applications. It includes Product Overview, Access Volume, IP
Service Volume, IP Routing Volume, IP Multicast Volume, QoS
Volume, Security Volume and System Volume.
H3C S5500-EI Series Ethernet
Switches Command Manual
It is used for assisting the users in using various commands. It
includes Command Index, Access Volume, IP Services Volume,
IP Routing Volume, IP Multicast Volume, QoS Volume, Security
Volume and System Volume.
Obtaining Documentation
You can access the most up-to-date H3C product documentation on the World Wide Web at this URL:
http://www.h3c.com.
The following are the columns from which you can obtain different categories of product documentation:
[Products & Solutions]: Provides information about products and technologies, as well as solutions.
[Technical Support & Document > Technical Documents]: Provides several categories of product
documentation, such as installation, configuration, and maintenance.
[Technical Support & Document > Software Download]: Provides the documentation released with the
software version.
Documentation Feedback
You can e-mail your comments about product documentation to [email protected].
We appreciate your comments.
Environmental Protection
This product has been designed to comply with the requirements on environmental protection. For the
proper storage, use and disposal of this product, national laws and regulations must be observed.
i
Table of Contents
1 Product Overview······································································································································1-1
Overview ·················································································································································1-1
Introduction to S5500-EI Series Ethernet Switches················································································1-3
S5500-28C-EI··································································································································1-3
S5500-28C-EI-DC ···························································································································1-5
S5500-52C-EI··································································································································1-5
S5500-28C-PWR-EI ························································································································1-6
S5500-52C-PWR-EI ························································································································1-7
S5500-28F-EI ··································································································································1-8
Ports······················································································································································1-10
Console Port··································································································································1-10
10/100/1000Base-T Ethernet Port·································································································1-10
SFP Port ········································································································································1-10
Combo Port ···································································································································1-12
LEDs······················································································································································1-13
System Status LED ·······················································································································1-13
Hot Swappable Power Module Status LEDs·················································································1-13
RPS Status LED ····························································································································1-14
Port Mode LED ······························································································································1-14
Seven-Segment LED·····················································································································1-15
10/100/1000Base-T Auto-Sensing Ethernet Port Status LED·······················································1-16
SFP Port Status LED·····················································································································1-17
Interface Module Status LED ········································································································1-17
Optional Interface Modules ···················································································································1-17
Dual-port GE SFP interface module······························································································1-18
Short-haul Dual-Port 10 GE CX4 Interface Module ······································································1-19
Dual-Port 10 GE SFP+ Interface Module ······················································································1-20
Dual-Port 10 GE XFP Interface Module ························································································1-22
One-port 10 GE XFP Interface Module ·························································································1-23
Description of LEDs of Interface Modules ·····················································································1-23
2 Preparing for Installation··························································································································2-1
Safety Precautions ··································································································································2-1
Installation Site········································································································································2-1
Temperature/Humidity·····················································································································2-1
Cleanness········································································································································2-1
Electromagnetic Susceptibility·········································································································2-2
Laser Safety ····································································································································2-2
Installation Tools ·····································································································································2-3
3 Installing the Switch··································································································································3-1
Installation Flow of the Switch·················································································································3-1
Installing the Switch into a 19-Inch Rack Using Mounting Brackets·······················································3-2
Installation Modes····························································································································3-2
Introduction to Mounting Bracket·····································································································3-3
ii
Introduction to Guide Rail················································································································3-4
Use Front Mounting Brackets to Install a Switch·············································································3-4
Use Front Mounting Brackets and a Tray to Install a Switch ··························································3-5
Use Front and Rear Mounting Brackets to Install a Switch·····························································3-6
Use Front Mounting Brackets and Guide Rails to Install a Switch··················································3-9
Mounting the Switch on a Workbench ··································································································3-11
Connecting the Grounding Cable··········································································································3-11
When a Grounding Strip is Available·····························································································3-12
Where a Grounding Conductor Can be Buried ·············································································3-13
In Other Installation Sites ··············································································································3-14
Installing a Power Module·····················································································································3-15
Installing the Power Module ··········································································································3-15
Removing the Power Module ········································································································3-16
Connecting the Power Cords ················································································································3-17
Connecting the AC Power Cord ····································································································3-17
Connecting the -48V DC Power Cord ···························································································3-18
Connecting the RPS Power Cord··································································································3-19
Installing an Interface Module ···············································································································3-21
Installing an Interface Card ···········································································································3-21
Removing an Interface Module ·····································································································3-22
Installing Dedicated CX4/SFP+ Cable ··························································································3-23
Removing Dedicated CX4/SFP+ Cable ························································································3-23
Installing Switches for an IRF ···············································································································3-23
Installation Flow for an IRF············································································································3-24
Drawing a Plan for an IRF with Switches ······················································································3-25
Verifying the Installation························································································································3-28
4 Starting and Configuring the Switch·······································································································4-1
Setting up the Configuration Environment ······························································································4-1
Connecting the Console Cable ···············································································································4-1
Console Cable ·································································································································4-1
Connection Procedure·····················································································································4-2
Setting Terminal Parameters ··················································································································4-2
Booting the Switch ··································································································································4-5
Checking before Powering on the Switch························································································4-5
Powering on the Switch···················································································································4-5
Changing the Startup Mode ············································································································4-8
5 Boot ROM and Host Software Loading ···································································································5-1
Introduction to Loading Modes················································································································5-1
Loading Software Through the Boot ROM Menu····················································································5-1
Boot Menu ·······································································································································5-1
Loading Software Using XMODEM Through Console Port·····························································5-3
Loading Software Using TFTP through Ethernet Port·····································································5-8
Loading Software Using FTP Through Ethernet Port····································································5-10
Loading Software Through CLI ·············································································································5-12
Loading Software Using FTP ········································································································5-12
Loading Software Using TFTP ······································································································5-14
iii
6 Maintenance and Troubleshooting··········································································································6-1
Software Loading Failure ························································································································6-1
Password Missing Failure ·······················································································································6-1
Missing User Password ···················································································································6-1
Missing Boot ROM Password··········································································································6-1
Power Supply Failure······························································································································6-2
Fixed Power Module Failure············································································································6-2
Hot Swappable Power Module Failure ····························································································6-3
Fan Failure ··············································································································································6-4
Configuration System Failure··················································································································6-4
1-1
1 Product Overview
Overview
H3C S5500-EI Series Ethernet Switches (hereinafter referred to as the S5500-EI series) are Layer 3
Gigabit Ethernet switching products developed by Hangzhou H3C Technologies Co., Ltd. (hereinafter
referred to as H3C).
The S5500-EI series are designed as distribution or access devices for intranets and metropolitan area
networks (MANs). Supporting IPv4/IPv6 dual stack and 10 GE uplink interfaces, the S5500-EI series
provide abundant service features and can also be used for connecting server groups in data centers.
The S5500-EI series support the H3C-specific cluster management function, which facilitates your
network management. And they also support the Intelligent Resilient Framework (IRF) technology. You
can connect multiple S5500-EI switches through 10 GE ports to form a logical entity, thus to establish a
new intelligent network with high reliability, expandability and manageability.
The S5500-EI series include six models, and have the system specifications as shown in
Table 1-1.
Table 1-1 System specifications of the S5500-EI series
Item
S5500-28
C-EI-DC
S5500-
28C-EI
S5500-52
C-EI
S5500-52C-
PWR-EI
S5500-28C-P
WR-EI
S5500-28F-EI
Physical
dimensions
(H × W × D)
43.6 × 440 × 300 mm
(1.72 × 17.32 × 11.81 in.)
43.6 × 440 × 420 mm
(1.72 × 17.32 × 16.54 in.)
43.6 × 440 ×
360 mm
(1.72 × 17.32 ×
14.17 in.)
Weight <5 kg (11.02 lb) <7.5 kg (16.53 lb) <6 kg (13.23 lb)
Management
port
One console port, on the front panel
24 ×
10/100/1000Base-T
auto-sensing
Ethernet port
4 × 1000Base-X
SFP port
48 ×10/100/1000Base-T
auto-sensing Ethernet
port
4 × 1000Base-X SFP port
24 ×
10/100/1000B
ase-T
auto-sensing
Ethernet port
4 ×
1000Base-X
SFP port
8 ×
10/100/1000Ba
se-T Ethernet
port
24 ×
100/1000Base-
X SFP port
The last four 10/100/1000Base-T Ethernet ports and the four SFP
ports comprise four Combo ports.
The last eight
SFP ports and
the eight
10/100/1000Ba
se-T Ethernet
ports comprise
eight Combo
ports.
GE ports
Note: For each Combo port, either the SFP port or the corresponding Ethernet port
can be used at a time. For details about the combo port mapping relationship, please
refer to
Table 1-5.
1-2
Item
S5500-28
C-EI-DC
S5500-
28C-EI
S5500-52
C-EI
S5500-52C-
PWR-EI
S5500-28C-P
WR-EI
S5500-28F-EI
Interface
card models
supported
(optional)
2, on the rear panel
z Dual-port GE SFP interface module (LSPM2GP2P, not support IRF)
z Short-haul dual-port 10GE CX4 interface module (LSPM1CX2P, support IRF)
z Dual-port 10 GE SFP+ interface module (LSPM2SP2P, support IRF)
z Dual-port 10 GE XFP interface module (LSPM1XP2P, support IRF)
z One-port 10 GE XFP interface module (LSPM1XP1P, support IRF)
Optional hot
swappable
power
modules
—
PSR150-A
PSR150-D
Power
supply
system
The S5500-28F-EI is delivered with a hot-swappable power module PSR150-A by
default. You can install another PSR150-A or a PSR150-D for backup.
The other five models of the S5500-EI series switches are designed with two fixed
power receptacles respectively. The two power inputs can be simultaneously used,
acting as backup for each other. Alternatively, you can use either power input.
Power
socket types
and quantity
1 -48V DC
power
socket and
1 RPS
power
socket
1 AC power socket
and 1 RPS power
socket
1 AC power socket and 1 RPS
power socket
PSR150-A: 1
AC power
socket
PSR150-D: 1
-48V DC power
socket
AC
Rated voltage range: 100 VAC to 240 VAC, 50 Hz or 60 Hz
Input voltage range: 90 VAC to 264 VA.C, 47 Hz to 63 Hz
–48V
DC
Rated voltage range: –48 VDC to –60 VDC
Input voltage range: –36 VDC to –72 VDC
You can use the –48 VDC power supply in the equipment room directly or one of the
following two external RPS power supply units recommended by H3C to provide
power supply.
z RPS500-A3 (–50 VDC/7.5 A, cable suite-0404A03V) or RPS1000-A3 (–54
VDC/8 A, cable suite-0404A054) for the PSR150-D power module installed on an
S5500-28F-EI.
z RPS500-A3 (–50 VDC/7.5 A, cable suite-0404A03U) for the S5500-28C-EI-DC.
Input
volta
ge
RPS
Use the external RPS power supply units recommended by H3C only.
z S5500-28C-EI/S5500-28C-EI-DC has a rated voltage range of 10.8 VDC to 13.2
VDC, and adopts RPS500-A3 using its 12 VDC/10.5 A output and the cable suite
of 0404A08G.
z S5500-52C-EI has a rated voltage range of 10.8 VDC to 13.2 VDC, and adopts
RPS800-A using its 12 VDC/17.25 A output and the cable suite of 0404A08G.
z S5500-28C-PWR-EI/S5500-52C-PWR-EI has a rated voltage range of –55 VDC
to –52 VDC, and adopts RPS1000-A3 using its –54 VDC/25 A output and the
cable suite of 0404A053.
Static power
consumption
27 W 36 W 63 W 83 W 60 W
PSR150-A: 44
W
PSR150-D: 30
W
1-3
Item
S5500-28
C-EI-DC
S5500-
28C-EI
S5500-52
C-EI
S5500-52C-
PWR-EI
S5500-28C-P
WR-EI
S5500-28F-EI
AC power
supply:
640 W, with
270 W of
system
power
consumption
and 370 W of
PoE power
AC power
supply:
575 W, with
205 W of
system power
consumption
and 370 W of
PoE power
Power
consumption
(full load)
105 W 110 W 155 W
RPS power
supply:
910 W, with
170 W of
system
power
consumption
and 740 W of
PoE power
RPS power
supply:
485 W, with
115 W of
system power
consumption
and 370 W of
PoE power
115 W
Cooling
system
4 fans 6 fans
6 fans (4 for the
system, and 1
for each power
module)
Operating
temperature
0°C to 45°C (32°F to 113°F)
Relative
humidity
(noncondens
ing)
10% to 90%
z Only the recommended RPS can be used for S5500-EI Ethernet switches. The –48 VDC in the
equipment room cannot be used directly. Otherwise, the device may be damaged.
z For details about the RPS power supply units, see the user manual and RPS Ordering Guide for
H3C Low-End Series Ethernet Switches.
Introduction to S5500-EI Series Ethernet Switches
S5500-28C-EI
Front Panel
The S5500-28C-EI Ethernet switch provides 24 × 10/100/1000Base-T auto-sensing Ethernet ports, four
1000 Base-X SFP ports and one console port on the front panel. The last four 10/100/1000Base-T
Ethernet ports and the four SFP ports comprise four Combo ports, with one port of a Combo port
working at a time.
1-4
Figure 1-1 Front panel of the S5500-28C-EI Ethernet switch
(1) 10/100/1000 Base-T auto-sensing Ethernet port
(2) 10/100/1000 Base-T auto-sensing Ethernet port status LED
(3) 1000 Base-X SFP port (4) 1000Base-X SFP port status LED
(5) Console port (6) Seven-segment LED
(7) Port mode LED (Mode) (8) System status LED (PWR)
(9) RPS status LED (RPS) (10) Interface module 1 status LED (MOD1)
(11) Interface module 2 status LED (MOD2) (12) Port status LED mode switching button
Rear Panel
Figure 1-2 Rear panel of the S5500-28C-EI Ethernet switch
(1) AC power input (2) RPS power input (shipped with a protective cover)
(3) Grounding screw (4) Interface module slot 1 (MOD1)
(5) Interface module slot 2 (MOD2)
The S5500-28C-EI provides two interface module slots on its rear panel. Each slot is installed with a
filler panel when the switch is shipped. You can select one or two interface modules for your switch as
needed. See
Optional Interface Modules on page 1-17 for the interface module models supported by
the S5500-EI series, and see
Installing an Interface Module on page 3-21 for the installation of interface
modules.
1-5
S5500-28C-EI-DC
Front Panel
The front panel of the S5500-28C-EI-DC is the same as that of the S5500-28C-EI. For related
description, refer to
S5500-28C-EI on page 1-3.
Rear Panel
Figure 1-3 Rear panel of the S5500-28C-EI-DC Ethernet switch
(1) -48V DC power input (2) RPS power input (shipped with a protective cover)
(3) Grounding screw (4) Interface module slot 1 (MOD1)
(5) Interface module slot 2 (MOD2)
The S5500-28C-EI-DC provides two interface module slots on its rear panel. Each slot is installed with
a filler panel when the switch is shipped. You can select one or two interface modules for your switch as
needed. See
Optional Interface Modules on page 1-17 for the interface module models supported by
the S5500-EI series, and see
Installing an Interface Module on page 3-21 for the installation of interface
modules.
S5500-52C-EI
Front Panel
The S5500-52C-EI Ethernet switch provides 48 ×10/100/1000Base-T auto-sensing Ethernet ports, four
1000 Base-X SFP ports and one console port on the front panel. The last four 10/100/1000Base-T
Ethernet ports and the four SFP ports comprise four Combo ports, with one port of a Combo port
working at a time.
1-6
Figure 1-4 Front panel of the S5500-52C-EI Ethernet switch
(1) 10/100/1000 Base-T auto-sensing Ethernet port
(2) 10/100/1000 Base-T auto-sensing Ethernet port status LED
(3) Console port (4) Seven-segment LED
(5) Port mode LED (Mode) (6) System status LED (PWR)
(7) RPS status LED (RPS) (8) Interface module 1 status LED (MOD1)
(9) Interface module 2 status LED (MOD2) (10) Port status LED mode switching button
(11) 1000 Base-X SFP port (12) 1000Base-X SFP port status LED
Rear Panel
Figure 1-5 Rear panel of the S5500-52C-EI Ethernet switch
(1) AC power input (2) RPS power input (shipped with a protective cover)
(3) Grounding screw (4) Interface module slot 1 (MOD1)
(5) Interface module slot 2 (MOD2)
The S5500-52C-EI provides two interface module slots on its rear panel. Each slot is installed with a
filler panel when the switch is shipped. You can select one or two interface modules for your switch as
needed. See
Optional Interface Modules on page 1-17 for the interface module models supported by
the S5500-EI series, and see
Installing an Interface Module on page 3-21 for the installation of interface
modules.
S5500-28C-PWR-EI
Front Panel
The S5500-28C-PWR-EI Ethernet switch provides 24 ×10/100/1000Base-T auto-sensing Ethernet
ports, four 1000 Base-X SFP ports and one console port on the front panel. The last four
10/100/1000Base-T Ethernet ports and the four SFP ports comprise four Combo ports, with one port of
a Combo port working at a time.
1-7
Figure 1-6 Front panel of the S5500-28C-PWR-EI Ethernet switch
(1) 10/100/1000 Base-T auto-sensing Ethernet port
(2) 10/100/1000 Base-T auto-sensing Ethernet port status LED
(3) 1000 Base-X SFP port (4) 1000Base-X SFP port status LED
(5) Console port (6) Seven-segment LED
(7) Port mode LED (Mode) (8) System status LED (PWR)
(9) RPS status LED (RPS) (10) Interface module 1 status LED (MOD1)
(11) Interface module 2 status LED (MOD2) (12) Port status LED mode switching button
Rear Panel
Figure 1-7 Rear panel of the S5500-28C-PWR-EI Ethernet switch
(1) RPS power input (2) AC power input
(3) Grounding screw (4) Interface module slot 1 (MOD1)
(5) Interface module slot 2 (MOD2)
The S5500-28C-PWR-EI provides two interface module slots on its rear panel. Each slot is installed
with a filler panel when the switch is shipped. You can select one or two interface modules for your
switch as needed. See
Optional Interface Modules on page 1-17 for the interface module models
supported by the S5500-EI series, and see
Installing an Interface Module on page 3-21 for the
installation of interface modules.
S5500-52C-PWR-EI
Front Panel
The S5500-52C-PWR-EI Ethernet switch provides 48 ×10/100/1000Base-T auto-sensing Ethernet
ports, four 1000 Base-X SFP ports and one console port on the front panel. The last four
10/100/1000Base-T Ethernet ports and the four SFP ports comprise four Combo ports, with one port of
a Combo port working at a time.
1-8
Figure 1-8 Front panel of the S5500-52C-PWR-EI Ethernet switch
(1) 10/100/1000 Base-T auto-sensing Ethernet port
(2) 10/100/1000 Base-T auto-sensing Ethernet port status LED
(3) Console port (4) Seven-segment LED
(5) Port mode LED (Mode) (6) System status LED (PWR)
(7) RPS status LED (RPS) (8) Interface module 1 status LED (MOD1)
(9) Interface module 2 status LED (MOD2) (10) Port status LED mode switching button
(11) 1000 Base-X SFP port (12) 1000Base-X SFP port status LED
Rear Panel
Figure 1-9 Rear panel of the S5500-52C-PWR-EI Ethernet switch
(1) RPS power input (2) AC power input
(3) Grounding screw (4) Interface module slot 1 (MOD1)
(5) Interface module slot 2 (MOD2)
The S5500-52C-PWR-EI provides two interface module slots on its rear panel. Each slot is installed
with a filler panel when the switch is shipped. You can select one or two interface modules for your
switch as needed. See
Optional Interface Modules on page 1-17 for the interface module models
supported by the S5500-EI series, and see
Installing an Interface Module on page 3-21 for the
installation of interface modules.
S5500-28F-EI
Front Panel
The S5500-28F-EI Ethernet switch provides 24 × 100/1000Base-X SFP ports, eight
10/100/1000Base-T auto-sensing Ethernet ports and one console port on the front panel. The last eight
SFP ports and the eight 10/100/1000Base-T Ethernet ports comprise eight Combo ports, with one port
of a Combo port working at a time.
1-9
Figure 1-10 Front panel of the S5500-28F-EI Ethernet switch
(1) 100/1000Base-X SFP port status LED (2) 10/100/1000 Base-T auto-sensing Ethernet port
status LED
(3) Console port (4) Port status LED mode switching button
(5) Interface module 1 status LED (MOD1) (6) Interface module 2 status LED (MOD2)
(7) System status LED (SYS) (8) Hot swappable power module 1 status LED
(PWR1)
(9) Hot swappable power module 2 status LED
(PWR2)
(10) Port mode LED (Mode)
(11) Seven-segment LED
Rear Panel
Figure 1-11 Rear panel of the S5500-28F-EI Ethernet switch
(1) Grounding screw (2) Hot swappable power module 1
(3) Hot swappable power module 2 (4) Interface module slot 1 (MOD1)
(5) Interface module slot 2 (MOD2)
z The S5500-28F-EI provides two interface module slots on its rear panel. Each slot is installed with
a filler panel when the switch is shipped. You can select one or two interface modules for your
switch as needed. See
Optional Interface Modules on page 1-17 for the interface module models
supported by the S5500-EI series, and see
Installing an Interface Module on page 3-21 for the
installation of interface modules.
z The S5500-28F-EI provides two power module slots on its rear panel, with only a power module
RPS150-A installed in PWR1 upon device delivery while a blank panel on PWR2. You can install a
power module, which can be PSR150-A or PSR150-D, in PWR2 to serve as a backup. For details
about PSR150-A and PSR150-D, refer to H3C PSR150-A & PSR150-D Power Modules User
Manual. For details about how to install the two power modules, refer to
Installing a Power Module.
1-10
Ports
Console Port
Each S5500-EI series provides one console port on the front panel. Table 1-2 describes the console
port specifications.
Table 1-2 Console port specifications
Item Specification
Connector type
RJ-45
Compliant standard
EIA/TIA-232
Transmission baud
rate
9600 bps to 115200 bps (defaulting to 9600 bps)
Service
z It can be connected to an ASCII terminal.
z It can be connected to a serial port of a local or remote (through a pair of
modems) PC running terminal emulation program.
10/100/1000Base-T Ethernet Port
Each S5500-EI series provides 10/100/1000Base-T Ethernet ports on its front panel. Table 1-3
describes the specifications of the 10/100/1000Base-T Ethernet ports.
Table 1-3 10/100/1000Base-T Ethernet port specifications
Item Specification
Connector type
RJ-45
Interface standard
z 10 Mbps, full duplex
z 100 Mbps, full duplex
z 1000 Mbps, full duplex
z MDI/MDI-X, auto-sensing
Max transmission
distance
100 m (328.08 ft.)
Transmission medium
Category-5 unshielded twisted pair cable
Standard
IEEE 802.3i, 802.3u, 802.3ab
SFP Port
Each S5500-EI series provides SFP ports on its front panel. You can select the SFP transceivers
described in
Table 1-4.
All SFP transceivers are hot swappable and optional. Therefore, networking is more flexible.
1-11
Table 1-4 SFP transceivers supported by the S5500-EI series SFP ports
Transceiver
Central
wavelength
Connect
or
Fiber
Max
transmiss
ion
distance
50/125 µm
multimode
optical fiber
550 m
(1804.5 ft)
SFP-GE-SX-MM850-A 850 nm
62.5/125 µm
multimode
optical fiber
275 m
(902.2 ft)
SFP-GE-LX-SM1310-A
10 km
(about 6.2
mi)
SFP-GE-LH40-SM1310
1310 nm
40 km
(about
24.9 mi)
SFP-GE-LH40-SM1550
40 km
(about
24.9 mi)
SFP-GE-LH70-SM1550
1550 nm
LC
9/125 µm
single mode
optical fiber
70 km
(about
43.5 mi)
SFP-GE-LX-
SM1310-BIDI
TX: 1310 nm
RX: 1490 nm
GE SFP
transcei
ver
SFP-GE-LX-
SM1490-BIDI
Note that
these two
transceiver
models
should be
used in
pairs.
TX: 1490 nm
RX: 1310 nm
LC
9/125 µm
single mode
optical fiber
10 km
(about 6.2
mi)
SFP-FE-SX-MM1310-A
62.5/125 µm
multimode
optical fiber
2 km
(about 1.2
mi)
SFP-FE-LX-SM1310-A
9/125 µm
single mode
optical fiber
15 km
(about 9.3
mi)
SFP-FE-LH40-SM1310
1310 nm
9/125 µm
single mode
optical fiber
40 km
(about
24.9 mi)
SFP-FE-LH80-SM1550 1550 nm
LC
9/125 µm
single mode
optical fiber
80 km
(about
49.7 mi)
SFP-FE-LX-S
M1310-BIDI
TX: 1310 nm
RX: 1550 nm
FE SFP
transcei
ver
SFP-FE-LX-S
M1550-BIDI
Note that
these two
transceiver
models
should be
used in
pairs.
TX: 1550 nm
RX: 1310 nm
LC
9/125 µm
single mode
optical fiber
15 km
(about 9.3
mi)
1-12
z You are recommended to use SFP transceivers of H3C on the S5500-EI series.
z The types of SFP transceivers may update with time. For information about transceivers, contact
H3C technical support or marketing staff.
z For the models and specifications of each kind of transceivers, refer to H3C Low End Series
Ethernet Switches Pluggable Modules Manual.
Combo Port
One SFP port and the corresponding 10/100/1000Base-T Ethernet port form a Combo port. For each
Combo port, either the SFP port or the corresponding 10/100/1000Base-T Ethernet port can be used at
a time. For details about the combo port mapping relationship, please refer to
Table 1-5.
Table 1-5 Combo port mapping relationship
Model SFP port 10/100/1000Base-T Ethernet port
GigabitEthernet1/0/25 GigabitEthernet1/0/22
GigabitEthernet1/0/26 GigabitEthernet1/0/24
GigabitEthernet1/0/27 GigabitEthernet1/0/21
S5500-28C-EI
S5500-28C-EI-DC
S5500-28C-PWR-EI
GigabitEthernet1/0/28 GigabitEthernet1/0/23
GigabitEthernet1/0/49 GigabitEthernet1/0/46
GigabitEthernet1/0/50 GigabitEthernet1/0/48
GigabitEthernet1/0/51 GigabitEthernet1/0/45
S5500-52C-EI
S5500-52C-PWR-EI
GigabitEthernet1/0/52 GigabitEthernet1/0/47
GigabitEthernet1/0/25 GigabitEthernet1/0/17
GigabitEthernet1/0/26 GigabitEthernet1/0/18
GigabitEthernet1/0/27 GigabitEthernet1/0/19
GigabitEthernet1/0/28 GigabitEthernet1/0/20
GigabitEthernet1/0/29 GigabitEthernet1/0/21
GigabitEthernet1/0/30 GigabitEthernet1/0/22
GigabitEthernet1/0/31 GigabitEthernet1/0/23
S5500-28F-EI
GigabitEthernet1/0/32 GigabitEthernet1/0/24
The SFP port and its corresponding 10/100/1000Base-T autosensing Ethernet port cannot be used
together at the same time. For details, refer to the Ethernet Port Configuration part in the Access
Volume of the H3C S5500-EI Series Ethernet Switches Operation Manual.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
