Sensio SA9005HDALWHK8THD Installation guide

Brand
Sensio
Model
SA9005HDALWHK8THD
Type
Installation guide

This manual is also suitable for

Sensio SA9005HDALWHK8THD is a square surface mount puck light with a power of 1.25W, designed for indoor use in dry rooms. It operates on low voltage (24V DC) and is suitable for under-cabinet lighting or attaching to a mounting surface such as wood or laminate. The light comes with an adhesive pad for easy affixing, or it can be screwed down. The LEDs in this fixture cannot be replaced. It's important to note that the fixture must not be covered by insulation and should not be exposed to steam or splashes. Use of surge protection in problem areas is recommended to maintain the warranty.

Sensio SA9005HDALWHK8THD is a square surface mount puck light with a power of 1.25W, designed for indoor use in dry rooms. It operates on low voltage (24V DC) and is suitable for under-cabinet lighting or attaching to a mounting surface such as wood or laminate. The light comes with an adhesive pad for easy affixing, or it can be screwed down. The LEDs in this fixture cannot be replaced. It's important to note that the fixture must not be covered by insulation and should not be exposed to steam or splashes. Use of surge protection in problem areas is recommended to maintain the warranty.

Installation
Instructions
Installation
Instructions
Product #: SA9007
Square Surface
Mount Puck Light
(1.25W)
IMPORTANT: Please read these instructions before starting installation and retain for future reference.
Components: Tools Required:
Important Safety Information
Safety Instructions
Screwdriver Bit
Drill
Please read these instructions carefully before attempting to install this product.
It is advisable to keep these instructions in a safe place for further reference. These products must not be modified; if
any modifications are made, it may invalidate the warranty and may render the product unsafe. These LED lights
operate on low voltage (24V). Do not wire the individual LED light fixtures directly to line power. This product is for
indoor use only. Keep out of moisture and use only in dry rooms.
The National Electrical Code (NEC) does not permit cords to be concealed where damage to insulation may go
unnoticed. To prevent fire danger, do not run cord behind walls, ceilings, soffits, or cabinets where it may be
inaccessible for examination. Cords should be visually examined periodically and immediately replaced when any
damage is noted.
CAUTION - To reduce the risk of fire, electric shock, or injury to persons:
a) Use only insulated staples or plastic ties to secure cords
b) Route and secure cords so that they will not be pinched or damaged when the cabinet is pushed to the wall
c) Not intended for recessed installation in ceilings, or soffits.
1.Turn off the main electrical supply for the appropriate
circuit at the breaker box.
2.This product is only suitable for connecting to a 24V DC
power source.
3.Position lights where they will not be exposed to
steam, splashes, etc.
4.The LEDs in this fixture cannot be replaced.
5. Suitable for under cabinet lighting, attached to a
mounting surface such as wood or laminate.
6.Failure to use surge protection in problem areas will
void the warranty.
7.Use only approved accessories.
8.IMPORTANT: Fixture must NOT be covered by
insulation.
Surface Light
Screws
Drill Bit
9-11mm
(3/8” -7/16”)
Adhesive
pad
Square Surface Mount Puck Light (1.25W)
1
Carefully remove LED light from square
cover
2
Screw down LED, or use adhesive pad
to affix to cabinet
3
Snap Square cover back on LED light
(proceed to step 5)
Mount for wire exiting side of LED light
1
Mark location for wire hole to be drilled
Feed lead wire through hole
2
3
Snap Square cover back on LED light
4
Sensio America
877-501-5337
www.sensioamerica.com
• Ensure that the power is disconnected prior to cleaning.
• To keep the finish of this product, wipe over with soft cloth
periodically.
• Do not use harsh chemical solvents, it may discolor or
damage the finish.
Maintenance & Care
Support
5
Run lead to driver
LED Power
Supply
Distributo
r
6
Connect driver to power
Mount for wire exiting under LED light
Screw down LED, or use adhesive pad
to affix to cabinet
  • Page 1 1
  • Page 2 2

Sensio SA9005HDALWHK8THD Installation guide

Brand
Sensio
Model
SA9005HDALWHK8THD
Type
Installation guide
This manual is also suitable for

Sensio SA9005HDALWHK8THD is a square surface mount puck light with a power of 1.25W, designed for indoor use in dry rooms. It operates on low voltage (24V DC) and is suitable for under-cabinet lighting or attaching to a mounting surface such as wood or laminate. The light comes with an adhesive pad for easy affixing, or it can be screwed down. The LEDs in this fixture cannot be replaced. It's important to note that the fixture must not be covered by insulation and should not be exposed to steam or splashes. Use of surge protection in problem areas is recommended to maintain the warranty.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents