Hagerco 4700 Series - SVR - Grade 1 Surface Vertical Rod Device Installation guide

Hagerco
Brand
Hagerco
Model
4700 Series - SVR - Grade 1 Surface Vertical Rod Device
Type
Installation guide

This manual is also suitable for

DEVICES COVERED IN THESE INSTRUCTIONS:
47DT Dummy-Pull When Dogged
47NL Night Latch - Key Retracts Latchbolt 47BE Blank Escutcheon - Always Operable
APPLICATIONS
TOOLS
10/28/2011
Cylinder collar
Cylinder locking plate
Trim actuating shaft
Cylinder cam
Lever handle
Mounting posts
Handing pin
47CE shown
Tools Required
Machine Screws Door Handing
1/2”
1-3/32”
1-1/4”
Door
[57]
C
L
1/4” - 20
C
L
Door
Surface Vertical Rod Exit Device
1-7/16”
[37]
2-1/4”
[57]
Vertical Rods
C
L
Surface Vertical Rod Exit Device
Door
2-1/4”
[57]
1-7/16”
[37]
Door Door
C
L
C
L
Surface Vertical Rod Exit Device
Rim Exit Device
Double Door
Strike
2-3/4”
[70]
2-3/4”
[70]
C
L
C
L
Door
Door
Rim Exit Device Rim Exit Device
Mullion
2-1/4”
[57]
2-1/4”
[57]
1 of 3
Single Door with Rim Device
Double Door with
SVR Device
Double Door with Mullion
Double Door with
Rim Device and
SVR Device
Inside of Door
Outside of Door
RHR
LHR
4700 Series Trim
Installation Instructions
I-ED00791
47CE Cylinder Escutcheon - Key Locks & Unlocks Lever
TRIM ACTUATING SHAFT
LEVER HANDLE
CYLINDER COLLAR
MOUNTING POSTS
HANDING PIN
CYLINDER LOCKING PLATE
CYLINDER CAM
CASHBOX NUT
47CE CYLINDER ESCUTCHEON SHOWN
Rim Exit Device
2-1/4”
4700 Series Trim
Installation Instructions
I-ED00791
INSTRUCTIONS
1. Set trim handing.
A. Rotate lever handle to the right or left direction to match desired door handing.
B. Insert square handing pin into hub as shown.
C. For Surface Vertical Rod devices only, be sure the handing matches what is indicated on the product box label.
Surface Vertical Rod handing cannot be changed in the field.
Note: See back of trim for a label that indicates which direction to position handle for RHR or LHR handing. The label
also indicates which direction the trim actuating shaft should rotate.
10/28/2011
Step 1A: Door Handing
Right Hand Reverse
(RHR)
Left Hand Reverse
(LHR)
(Not applicable on
Rim devices)
(Not applicable on
Rim devices)
RHR
LHR
Hub
Square Handing Pin
Step 1B: Insert Square Handing Pin
2. Install mortise cylinder.
A. Remove key from mortise cylinder.
B. Slide wave washer (if desired) and cylinder collar onto mortise cylinder body.
C. Install mortise cylinder into escutheon trim with cam position as shown.
D. Install cylinder locking plate and use stet screws to secure.
Wave Washer
Cylinder Collar
Mortise Cylinder
Position Cam pointing up
Mortise Cylinder
Cylinder
Locking
Plate
Step 2D + 2E: Install Cylinder Locking Plate
Step 2B & 2C:
Install Mortise Cylinder
2 of 3
E. Screw cylinder nut onto mortise cylinder until secure.
CYLINDER COLLAR
WAVE SPRING
MORTISE CYLINDER
POSITION CAM POINTING UP
MORTISE CYLINDER
CYLINDER
LOCKING
PLATE
4700 Series Trim
Installation Instructions
I-ED00791
INSTRUCTIONS (CONTINUED)
3. Mark and drill mounting holes for escutcheon trim.
A. Mark horizontal centerline by matching it to exit
device centerline, which can be found on push
side of door.
B. Apply template to door using centerline. Refer
to Applications section on page one to
determine location of vertical centerline.
Vertical centerline should match exit device
vertical centerline located on push side of door.
C. Mark and drill 1/2” holes for mounting posts as
shown on template.
D. Mark and drill 1/2” hole for trim actuator shaft,
which mates with exit device (not required for
47DT). See exit device instructions for further
details.
10/28/2011
4. Install escutcheon trim.
A. Insert trim mounting posts and
actuating shaft through door.
B. Mate trim actuating shaft with
cam on back of exit device.
C. Secure from push side of door
with provided 1/4” - 20 screws.
D. Test installation by rotating lever
handle or key to verify trim
activates exit device.
Note: Dummy trim is only for pulling
door. The handle does not rotate.
3 of 3
Trim actuator shaft hole
Ø 1/2”
Trim
mounting
holes
Ø 1/2”
See page one for details on
your specific application
2-7/8”
[73]
Trim actuating shaft
Door
Exit device mounting
holes
Cam mates with trim
actuating shaft
  • Page 1 1
  • Page 2 2
  • Page 3 3

Hagerco 4700 Series - SVR - Grade 1 Surface Vertical Rod Device Installation guide

Hagerco
Brand
Hagerco
Model
4700 Series - SVR - Grade 1 Surface Vertical Rod Device
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents